Loading...
Report (22) Oregon Residential Specialty Code N1107.2 HIGH-EFFICIENCY INTERIOR LIGHTING SYSTEMS Permit No.: �. 5 .��� c>c)o q Jurisdiction: Site Address: 1 33 AJ`4-- Subdivision/Lot#: and/or Map and Tax Lot#: By my signature below, I certify that all of the permanently installed lighting fixtures in the above mentioned building contain high-efficacy lamps. Screw-in compact fluorescent and LED lamps comply with this requirement. (Oregon Residential Specialty Code N1107.2)1 Signature: Date: 6 Owne/General Contractor/Authorized Agent Print Name: Ake*--0 'ORSC Section N1107.2.High-efficacy lamps. All permanently installed lighting fixtures shall contain high- efficacy lamps. Screw-in compact fluorescent and LED lamps comply with this requirement. The building official shall be notified in writing at the final inspection that the permanently installed lighting fixtures have met this requirement. Exception: Two permanently installed lighting fixtures are not required to have high-efficacy lamps. I:\Building\Forms\RES-HighEfficiencyLightingAcknowledgement_022018 Oregon Residential Specialty Code R318.2 MOISTURE CONTENT ACKNOWLEDGEMENT FORM I, , am the general contractor or the owner-builder at the following address: Site Address: I _ i% City: *. Permit#: p.‘% c- i- \ -- 0000 .{ Subdivision/Lot#: and/or Map and Tax Lot#: To conform with the 2017 Oregon Residential Specialty Code(ORSC), Section R318.2 and OAR 918-480-0140, I am notifying the building official that I am aware of the moisture content Requirement of ORSC Section R318.2 and have taken steps to meet this code requirement. [Section R318.2 is provided for reference]. R318.2 Moisture Content: Prior to the installation of interior finishes,the building official shall be notified in writing by the general contractor that all moisture-sensitive wood framing members used in construction have a moisture content of not more than 19 percent by dry weight of dry framing members. Signature: Date: Genera C tractor or Owner-Builder I:\Building\Form\RES-MoistureContentAcknowledgement_022018 Oregon Residential Specialty Code R408.1 OISTURE BARRIER ACKNOWLEDGEMENT FORM I, , am the general contractor or the owner-builder at the following address: Site Address: (41 _1,3 3 5 -76 +'4. toy.— City: 1-`,/` Permit#: Subdivision/Lot#: and/or Map and Tax Lot#: 2-7-- To conform with the 2017 Oregon Residential Specialty Code (ORSC), Section R408.1 Ventilation. I am notifying the building official that I have installed the Moisture Barrier as per Requirement in ORSC Section 408.1 and have taken the following steps to meet this code requirement: NThe ground surface of the under-floor space is covered by a Class I vapor retarder or other approved materials,with 1i Joints lapped 12 inches at seams and If' Extending up the foundation walls 12 inches. Signature: Date: C)-- V /C( Gener 1 Contractor or Owner-Builder I:\Buildin \Form\RES-MoistureBarrierAcknowled ement 022018 B S _ pi,sra&,S r a6aa " r '>S 33 Srw -76 4 q , 1 „,..„,.,6 rui , ...., , A .11SI i. . , ,,,, ,..,, ,s, A -14,"4,4 Local Relationships.National Resources. USI JB Insulation 14255 SW Galbreath Drive Sherwood, OR 97140 Installed Insulation Certificate We certify that the insulation material listed here was installed at the address listed below: Other than loose fill only aluminum foil only loose flif a aluminum foil Initial)riled& Aluminum Foam No.of Coverage ; Minimum Settled,f } Air Spaces Direction of Loose Fill Kraft Unfaced Foil Open/Closed BIBS® R-Value Thickness Pkgs Area(SF);' Thickness, . ;No,(Thickness Heat Flow Attic _'► ❑ ❑ ❑ 0 ❑ 49 j Ceilings ❑ ❑ ��� ❑ ❑ ❑ 49 i I i Floors ❑ ❑ ❑ ❑ ❑ ❑ f j Walls 0 e ❑ ❑ ❑ ❑ 21 1 Basement ❑ ❑ ❑ ❑ ❑ ❑ Crawlspace ❑ ❑ '°1 ❑ ❑ ❑ 30 Other ❑ ❑ ❑ ❑ ❑ ❑ i � M� 3 lib _....10111111110 Contractor - .�"”— Address or Lot Number: 14833 SW 76th AVE LOT 22 (Signatur City,ST Zip: PORTLAND,OR 97224 „"- Title _ ��, Date Installed: / TT.OPS.FRM.010