Report (81) k 445f-vl1-- /
F Residential Energy Additional
I I I � S w /pc)�
. ;''',-.*,'•.4, Measure Selection �' .
i- ' `i= Department of Consumer and Business Services
• "' Building Codes Division JAN 3 2B1g5
I'-5g 1535 Edgewater NW,Salem,Oregon
Mailingaddress:P.O.Box 14470,Salem,OR 97309-0404 CITa OF
503-373-1210•Fax:503-378-3656 � .
Web:bcd.oregon.gov RD
U I M3 DI'1V i tO(
RESIDENTIAL INFORMATION
Date: 1/2/2018 Building permit number:
Owner's name: Andrew Meeker
Job address: 11180 SW Errol St
City: Tigard State:oR ZIP: 97223
INSTRUCTIONS
Please select type of construction below; sign,date, and complete the entire form. Submit this form with
your permit application or your project will be placed on hold until the required information is provided.
❑ New construction.All conditioned spaces within residential buildings must comply with Table N1101.1(1)and two
additional measures(one numbered and one lettered)from Table N1101.1(2)on page 2.
Additions.Additions to existing buildings or structures may be made without making the entire building or structure
comply if the new additions comply with the requirements of this chapter. (N1101.3)
❑■ Large additions.Additions that are equal to or more than 40 percent of the existing building heated floor area or 600
square feet(55 m2)in area,whichever is less,must comply with Table N1101.1(2)on page 2. (N1101.3.1) (Note: You
must select one numbered and one lettered measure.)
El Small additions.Additions that are less than 40 percent of the existing building heated floor area or less than 600
square feet in area,whichever is less,must select one measure from Table N1101.1(2)on page 2 or comply with Table
N1101.3 below. (N1101.3.2)
El Exception: Additions that are less than 15 percent of existing building heated floor area or 200 square feet(18.58 m2)
in area,whichever is less,are not required to comply with Table N1101.1(2)or Table N1101.3.
Selected item number: Selected item letter:
Note:Depending on which Additional Measures you have selected, there may be sub-options that you will have to specify.
Check the appropriate box if provided.
Applicant's signature: Print name:
TABLE N1101.3—SMALL ADDITION ADDITIONAL MEASURES(SELECT ONE)
❑ 1 Increase the ceiling insulation of the existing portion of the home as specified in Table N1101.2.
❑ 2 Replace all existing single-pane wood or aluminum windows to be U-value as specified in Table N1101.2.
Insulate the floor system as specified in Table N1101.2 and install 50 percent of permanently installed lighting fixtures
D 3 as CFL or linear fluorescent or min.efficacy of 40 lumens per watt as specified in Section N1107.2.
O 4 Test the entire dwelling with blower door and exhibit no more than 7.0 air changes per hour @ 50 Pascals.
O 5 Seal and performance test the duct system.
❑ 6 Replace existing 78 percent AFUE or less gas furnace with a 92 percent AFUE or greater system.
0 7 Replace existing electric radiant space heaters with a ductless mini-split system with a minimum HSPF of 8.5.
O 8 Replace existing electric forced air furnace with an air source heat pump with a minimum HSPF of 8.5.
O 9 Replace existing water heater for a natural gas/propane water hear with a minimum EF of 0.67.
O 10 Install a solar water heating system with a minimum of 40 square feet of gross collector area.
PcCtEP.�ftT11EnT OF
C,�.OBN{�S5UMEEER
,(Sills R�1Cf5 440-4854(2/16/COM) Page 1
TABLE N1101.1(2) ADDITIONAL MEASURES
High-efficiency walls and windows:
❑ 1 Exterior walls-U-0.047/R-19+5(insulation sheathing)/SIPS,and one of the following options:
O Windows—Max 15 percent of conditioned area,or
❑ Windows—U-0.30
High-efficiency envelope:
Exterior walls—U-0.058/R-2I Intermediate framing,and
Vaulted ceilings—U-0.033/R-30Ad'`,and
Flat ceilings—U-0.025/R-49,and
® 2 Framed floors—U-0.025/R-38,and
Windows—U-0.30;and
❑ Doors—All doors U-0.20,or
❑ Additional 15 percent of permanently installed lighting fixtures as high-efficacy lamps or
0 Conservation Measure D and E
High-efficiency ceiling,window and duct sealing(Cannot be used with Conservation Measure E)
❑ 3 Vaulted ceilings—U-0.033/R-30A C,and
Flat ceiling—U-0.025/R-49,and
Windows—U-0.30,and Performance tested duct systemsb
❑ 4 High-efficiency thermal envelope UA:
Proposed UA is 15 percent lower than the Code UA when calculated in Table N1104.1(1)
Building tightness testing,ventilation and duct sealing:
A mechanical exhaust,supply,or combination system providing whole-building ventilation rates specified in Table Ni 101.1(3),or
❑ 5 ASHRAE 62.2,and
The dwelling must be tested with a blower door and found to exhibit no more than
O 1.6.0 air changes per hourrand
O 2.Performance tested duct systemsb
C 6 Duct tested HVAC systems within conditioned space:(Cannot be used with Conservation Measure B or C)
All ducts and air handler are contained within building envelope'
11 High-efficiency HVAC system:
El A
❑ Gas-fired furnace or boiler with minimum AFUE of 90 percent a,or 0 Air-source heat pump with minimum HSPF of 8.5 or
O Closed-loopground source heat pumpwith minimum COP of 3.0
❑ B Ducted HVAC systems within conditioned space:
All ducts and air handler are contained within building envelop&
Ductless heat pump:
Replace electric resistance heating in at least the primary zone of dwelling with at least one ductless mini-split heat pump having a
minimum HSPF of 8.5.Unit must not have integrated backup resistance heat,and the unit(or units,if more than one is installed in the
0 C dwelling)must be sized to have capacity to meet the entire dwelling design heat loss rate at outdoor design temperature condition.
Conventional electric resistance heating may be provided for any secondary zones in the dwelling.A packaged terminal heat pump
(PTHP)with comparable efficiency ratings may be used when no supplemental zonal heaters are installed in the building and integrated
backup resistance heat is allowed in a PTHP
High-efficiency water heating and lighting:
Natural gas/propane,on-demand water heating with minimum EF of 0.80,or heat pump water heater with minimum EF of 1.8(northern
D climate)and a minimum 75 percent of permanently installed lighting fixtures as CFL or linear fluorescent or a minimum efficacy of 40
lumens per watt as specified in Section N1107.2
Energy management device and duct sealing
C E Whole building energy management device that is capable of monitoring or controlling energy consumption,and
Performance tested duct systemsb,and
A minimum 75 percent of permanently installed fixtures as high efficacy lamps
❑
F Solar photovoltaic:
Minimum 1 watt/sq.ft.conditioned floor spaces
❑ G Solar water heating:
Minimum of 40 112 of gross collector areab
For SI:1 square foot=0.093 m2,I watt per square foot=10.8 W/m2.
a. Furnaces located within the building envelope must have sealed combustion air installed.Combustion air must be ducted directly from the outdoors.
b. Documentation of Performance Tested Ductwork shall be submitted to the building official upon completion of work.This work shall be performed by a technician certified by the
Performance Tested Comfort Systems(PTCS)program administered by the Bonneville Power Administration(BPA),documentation shall be proved that work demonstrates conformance to
PTCS duct performance standards.
c. Section N1107.2 requires 50 percent of permanently installed lighting fixtures to contain high efficacy lamps.Each of these additional measures adds an additional percent to the Section
N 1107.2 requirement.
d. A=advanced frame construction,which must provide full required ceiling insulation value to the outside of exterior walls.
e. The maximum vaulted ceiling surface area must not be greater than 50 percent of the total heated space floor area unless vaulted area has a U-factor no greater than U-0.026,
f. Building tightness test must be conducted with a blower door depressurizing the dwelling 50 Pascal's from ambient conditions.Documentation of blower door test must be submitted to the
Building Official upon completion of work.
g. Solar electric system size must include documentation indicating that Total Solar Resource Fraction is not less than 75 percent.
h. Solar water heating panels must be Solar Rating and Certification Corporation(SRCC)Standard 00-300 certified and labeled,with documentation indicating that Total Solar Resource
Fraction is not less than 75 percent.
i. A total of 5 percent of an HVAC systems ductwork must be permitted to be located outside of the conditioned space.Ducts located outside the conditioned space must have insulation
installed as required in this code.
440-4854(2/16/COM) Page 2
FOR OFFICE USE ONLY-SITE ADDRESS: I 1l?U Sit) /'VU f
This form is recognized by most building departments in the Tri-County area for transmitting information.
Please complete this form when submitting information for plan review responses and revisions.
This form and the information it provides helps the review process and response to your project.
City of Tigard • COMMUNITY DEVELOPMENT DEPARTMENT
'PI Transmittal a smittal Letter
T1 ; \k n 13125 SW Hall Blvd. • Tigard, Oregon 97223 • 503.718.2439 • www.tigard-or.gov
TO: 1 Orli DATFttyrnp
DEPT: BUILDING DIVISION
_. AN t�,N 9 Z018
FROM: ( `) yyl Mpekey-
CITY OF TIGARD
COMPANY: r BUILDING DIVISION
PHONE: fTi ' 276, 7gz 7 By:
RE: f 1R� t -Lyre, ' St (Permiik., -c.-- 2)( L.��t�C./(
(Site ddre
A Rc)
(Project name or subdivision name and lot number)
ATTACHED ARE THE FOLLOWING ITEMS:
Copies: Description: Copies: Description:
Additional set(s) of plans. Revisions:
Cross section(s) and details. Wall bracing and/or lateral analysis.
Floor/roof framing. Basement and retaining walls.
Beam calculations. Engineer's calculations.
X Other(explain): Ti rf1,,a. l Dejc t
REMARKS:
FOR OFFICE USE ONLY
Routed to Permit Technician: Date: i----- 1.11 — J 8 Initials: 11
Fees Due: ❑Yes No Fee Description: Amount Due:
$
$
$
Special
Instructions:
Reprint Permit(per PE): [ Yes ]No [ Done
Applicant Notified: Date: 7 Initials:
I:\Building\Forms\TransmittalLetter-Revisions.doc 05/25/2012