Loading...
Report iiCOMcheck Software Version 4.0.0 Envelope Compliance Certificate RECEIVED Section 1: Project Information DEC 3 0 2015 Energy Code:2014 Oregon Energy Efficiency Specialty Code CITY OF TIGARD Project Title: River Terrace North Pump Station and Force Main BUILDING DIVISION Project Type: New Construction Envelope Compliance Method:Simplified Trade-Off Construction Site: Owner/Agent: goer/Contractor: 17480 SW Clementine St Mike Kebbe Alex Bargmeyer Beaverton,OR 97007 Clean Water Services Murray,Smith&Assocates,Inc. Building Location(for weather data): Tigard,Oregon OFFICE COPY Climate Zone: 4c Building Use:Area Type Floor Area �y-,�, 1-Pump Station(Workshop):Nonresidential 815 A-5UP2EJ' --nC2Cy 1711nU Si Clrwie.k )1 c S7- Section 2: Envelope Assemblies and Requireme is Checklist Envelope FAILS: Design 3 pc..worse than code. Envelope Assemblies: - Component Name/Description Gross Cavity Cont. Proposed Budget Area or R-Value R-Value U-Factor U-Factorial Perimeter Roof 1:Attic Roof with Wood Joists,[Bldg.Use 1 -Pump Station] 519 38.0 0.0 0.027 0.027 Exterior Wall 1:Concrete Block:8",Partially Grouted,Cells 940 0.0 10.9 0.070 0.150 Empty,Normal Density,Furring:Wood,[Bldg.Use 1 -Pump Station] Door 1:Insulated Metal,Swinging,[Bldg.Use 1 -Pump Station] 21 --- --- 0.700 0.700 Door 2:Insulated Metal,Swinging,[Bldg.Use 1 -Pump Station] 21 --- --- 0.700 0.700 Door 3:Insulated Metal,Swinging,[Bldg.Use 1 -Pump Station] 48 --- --- 0.700 0.700 Basement Wall 1:Solid Concrete:12"Thickness,Normal Density, 973 --- 0.0 0.630 0.108 Furring:None,Wall Ht 11.0,Depth B.G.11.0,[Bldg.Use 1 - Pump Station] Floor 1:Slab-On-Grade:Unheated,[Bldg.Use 1 -Pump Station] 458 --- --- --- --- (a)Budget U-factors are used for software baseline calculations ONLY,and are not code requirements. In the following requirements,blank checkboxes identify requirements that the applicant has not acknowledged as being met. Checkmarks identify requirements that the applicant acknowledges are met or excepted from compliance. 'Plans reference page/section'identifies where in the plans/specs the requirement can be verified as being satisfied. Fenestration Product Rating: ✓ 1. U-factors of fenestration products(windows,doors and skylights)are determined in accordance with NFRC 100 by an accredited, independent laboratory,and labeled and certified by the manufacturer or are determined using the commercial size category values listed in Chapter 15 of the 2009 ASHRAE Handbook of Fundamentals,Table No.4 and shall include the effects of the window frame. The temporary label afixed to the fenestration products must not be removed prior to inspection. Plans reference page/section: G-6 u 2. Solar heat gain coefficient(SHGC)of glazed fenestration products(windows,glazed doors and skylights)shall be determined in accordance with NFRC 200 by an accredited,independent laboratory,and labeled and certified by the manufacturer or be determined using the Solar Heat Gain Coefficients(SHGC)in Chapter 15 of the 2009 ASHRAE Handbook of Fundamentals,Table No.10.The overall values must consider type of frame material and operator for the SHGC at normal incidence. Exception(s): Li Site-built fenestration products shall have a single certificate specifying glazing type,special coatings,spacers,gas fills, center-of-glass and overall U-factor,and center-of-glass SHGC for every type of site built glass used.These certificates shall be maintained on the jobsite and made available to the inspector. Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- Plans reference page/section: NA Air Leakage, Insulation,and Component Certification: • 3. Sealing of the building envelope.Openings and penetrations in the building envelope are sealed with caulking materials or closed with gasketing systems compatible with the construction materials and location.Joints and seams are sealed in the same manner or taped or covered with a moisture vapor-permeable wrapping material.Sealing materials spanning joints between construction materials allow for expansion and contraction of the construction materials. Plans reference page/section: • 4. Window and door assemblies.The air leakage of window and sliding or swinging door assemblies that are part of the building envelope are determined in accordance with AAMA/WDMA/CSA 101/I.S.2/A440,or NFRC 400 by an accredited,independent laboratory,and labeled and certified by the manufacturer. Plans reference page/section: • 5. Curtain wall,storefront glazing and commercial entrance doors.Curtain wall,storefront glazing and commercial-glazed swinging entrance doors and revolving doors are tested for air leakage in accordance with ASTM E 283. For curtain walls and storefront glazing, the maximum air leakage rate is 0.3 cubic foot per minute per square foot of fenestration area.For commercial glazed swinging entrance doors and revolving doors,the maximum air leakage rate is 1.00 cfm/ft2 of door area. Requirement is not applicable. Plans reference page/section: • 6. Building thermal envelope insulation.An R-value identification mark is applied(by manufacturer)to each piece of insulation 12 inches or greater in width.Alternately,the insulation installers have provided a signed,dated and posted certification listing the type, manufacturer and R-value of insulation installed.Refer to code section for blown or sprayed insulation installation/settling depths and marker requirements. • 7. Insulation mark installation. Insulating materials are installed such that the manufacturer's R-value mark is readily observable upon inspection. • 8. Insulation product rating.The thermal resistance(R-value)of insulation has been determined in accordance with the U.S. FTC R-value rule. • 9. Installation.All material,systems and equipment are installed in accordance with the manufacturer's installation instructions and the International Building Code. • 10.Outdoor air intakes and exhaust openings.Stair and elevator shaft vents and other outdoor air intakes and exhaust openings integral to the building envelope shall be equipped with not less than a Class I motorized,leakage-rated damper with a maximum leakage rate of 4 cfm per square foot at 1.0 inch water gauge when tested in accordance with AMCA 500D.Stair and shaft vent dampers shall be capable of being automatically closed during normal building operation and interlocked to open as required by fire and smoke detection systems. Requirement is not applicable. Plans reference page/section: • 11.Loading dock weatherseals.Cargo doors and loading dock doors are equipped with weather seals to restrict infiltration when vehicles are parked in the doorway. Requirement is not applicable. Plans reference page/section: 12.Recessed lighting. Recessed luminaires installed in the building thermal envelope are sealed to limit air leakage between conditioned and unconditioned spaces.All recessed luminaires are IC-rated and labeled as meeting ASTM E 283.All recessed luminaires are sealed with a gasket or caulk between the housing and interior wall or ceiling covering. Requirement is not applicable. Plans reference page/section: • 13.Vestibules. Doors that separate conditioned space from the exterior are protected with an enclosed vestibule,with all doors of the vestibule equipped with self-closing devices.Vestibules are designed so interior and exterior doors to not operate simultaneously. Exception applies:Doors that open directly from a space less than 3000 sq.ft.in area. Plans reference page/section: A-1 • 14'Other'components have supporting documentation for proposed U-Factors. Plans reference page/section: Project Notes: Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- The basement portion or valve vault of the envelope does not meet the insulation requirement because the valve vault is an unoccupied, declassified space with continous ventilation air changes. The surrounding ground provides additional heat to the system that would otherwise be reduced by insulation and higher heating costs. Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- COMcheck Software Version 4.0.0 Interior Lighting Compliance Certificate Section 1: Project Information Energy Code:2014 Oregon Energy Efficiency Specialty Code Project Title: River Terrace North Pump Station and Force Main Project Type: New Construction Envelope Compliance Method:Simplified Trade-Off Construction Site: Owner/Agent: Designer/Contractor: 17480 SW Clementine St Mike Kebbe Alex Bargmeyer Beaverton,OR 97007 Clean Water Services Murray,Smith&Assocates, Inc. Section 2: Interior Lighting and Power Calculation A B C D Area Category Floor Area Allowed Allowed Watts (ft2) Watts/ft2 (B x C) Control Room(Common Space Types:Workshop)(Ceiling Height 10 ft.) 356 1.64 584 Valve Vault(Common Space Types:Workshop)(Ceiling Height 10 ft.) 459 1.64 753 Total Allowed Watts= 1337 Section 3: Interior Lighting Fixture Schedule A B C D E Fixture ID:Description/Lamp/Wattage Per Lamp/Ballast Lamps/ #of Fixture (C X D) Fixture Fixtures Watt. Control Room(Common Space Types:Workshop 356 sq.ft.) LED 1:Other: 1 7 66 462 Valve Vault(Common Space Types:Workshop 459 sq.ft.) LED 1:Other: 1 9 66 594 Total Proposed Watts= 1056 Section 4: Requirements Checklist In the following requirements,blank checkboxes identify requirements that the applicant has not acknowledged as being met. Checkmarks identify requirements that the applicant acknowledges are met or excepted from compliance. 'Plans reference page/section'identifies where in the plans/specs the requirement can be verified as being satisfied. Lighting Wattage: u 1. Total proposed watts must be less than or equal to total allowed watts. Allowed Wattage:1337 Proposed Wattage:1056 Complies:YES Mandatory Requirements: Li 2. Exit signs.Internally illuminated exit signs shall not exceed 5 watts per side. Plans reference page/section: u 3. Daylight zone control.All daylight zones are provided with individual controls that control the lights independent of general area lighting in the non-daylight zone.In all individual daylight zones larger than 350 sq.ft.,automatic daylight controls is provided.Automatic daylight sensing controls reduce the light output of the controlled luminaires at least 50 percent,and provide an automatic OFF control, while maintaining a uniform level of illumination.Contiguous daylight zones adjacent to vertical fenestration may be controlled by a single controlling device provided that they do not include zones facing more than two adjacent cardinal orientations(i.e.,north,east, south,west).Daylight zones under skylights shall be controlled separately from daylight zones adjacent to vertical fenestration. Exception(s): 0 Retail spaces adjacent to vertical glazing(retail spaces under overhead glazing are not exempt). ❑ Display,exhibition and specialty lighting Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- LI HID lamps 150 watts or less. p Spaces required to have occupancy sensors. Plans reference page/section: u 4. Interior lighting controls.At least one local shutoff lighting control has been provided for every 2,000 square feet of lit floor area and each area enclosed by walls or floor-to-ceiling partitions.The required controls are located within the area served by the controls or are a remote switch that identifies the lights served and indicates their status. Exception(s): p Lighting systems serving areas designated as security or emergency areas that must be continuously lighted. Li Lighting in public areas such as concourses,stairways or corridors that are elements of the means of egress with switches that are accessible only to authorized personnel. LI Lighting for warehouses,parking garages or spaces using less than 0.5 watts per square foot. Li Lighting for contiguous,single-tenant retail spaces. Plans reference page/section: Li 5. Sleeping unit controls.Master switch at entry to hotel/motel guest room. Plans reference page/section: O 6. Egress lighting.Egress illumination is controlled by a combination of listed emergency relay and occupancy sensors to shut off during periods that the building space served by the means of egress is unoccupied. Exception(s): O Building exits as defined in Section 1002 of the Oregon Structural Specialty Code. Plans reference page/section: O 7. Additional controls. Each area that is required to have a manual control shall have additional controls that meet the requirements of Sections 505.2.2.1 and 505.2.2.2. Plans reference page/section: O 8. Light reduction controls. Each space required to have a manual control also allows for reducing the connected lighting load by at least 50 percent by either 1)controlling(dimming or multi-level switching)all luminaires;or 2)dual switching of alternate rows of luminaires,alternate luminaires,or alternate lamps;or 3)switching the middle lamp luminaires independently of other lamps;or 4)switching each luminaire or each lamp. Exception(s): Li Only one luminaire in space. LI An occupant-sensing device controls the area. U The area is a corridor,storeroom,restroom,public lobby or sleeping unit. J Electrical and mechanical room. LI Areas that use less than 0.6 Watts/sq.ft. Plans reference page/section: Li 9. Buildings larger than 2,000 square feet are equipped with an automatic control device to shut off lighting in those areas.This automatic control device shall function on either: 1)a scheduled basis,using time-of-day,with an independent program schedule that controls the interior lighting in areas that do not exceed 10,000 square feet and are not more than one floor;or 2)an occupant sensor that shall turn lighting off within 30 minutes of an occupant leaving a space;or 3)a signal from another control or alarm system that indicates the area is unoccupied. Exception(s): LI Sleeping units,patient care areas;and spaces where automatic shutoff would endanger safety or security. Plans reference page/section: ▪ 10.Occupancy sensors in rooms that include daylight zones are required to have Manual ON activation. Plans reference page/section: ▪ 11.An occupant sensor control device is installed that automatically turns lighting off within 30 minutes of all occupants leaving a space. Exception(s): U Classrooms and lecture halls. U Conference,meeting and training rooms. Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- ❑ Employee lunch and break rooms. ❑ Rooms used for document copying and printing. ❑ Office spaces up to 300 square feet. ❑ Restrooms. ❑ Dressing,fitting and locker rooms. Plans reference page/section: ❑ 12.Additional controls.An occupant sensor control device that automatically turns lighting off within 30 minutes of all occupants leaving a space or a locally activated switch that automatically turns lighting off within 30 minutes of being activated is installed in all storage and supply rooms up to 1000 square feet. Plans reference page/section: ❑ 13.Occupant override.Automatic lighting shutoff operating on a time-of-day scheduled basis incorporates an override switching device that: 1)is readily accessible,2)is located so that a person using the device can see the lights or the area controlled by that switch,or so that the area being lit is annunciated,3)is manually operated,4)allows the lighting to remain on for no more than 2 hours when an override is initiated,and 5)controls an area not exceeding 2,000 square feet. Exception(s): ❑ In malls and arcades,auditoriums,single-tenant retail spaces,industrial facilities and arenas,where captive-key override is utilized,override time is permitted to exceed 2 hours. ❑ In malls and arcades,auditoriums,single-tenant retail spaces,industrial facilities and arenas,the area controlled shall not exceed 20,000 square feet. Plans reference page/section: ❑ 14.Holiday scheduling.Automatic lighting shutoff operating on a time-of-day scheduled basis has an automatic holiday scheduling feature that turns off all loads for at least 24 hours,then resumes the normally scheduled operation. Exception(s): ❑ Retail stores and associated malls,restaurants,grocery stores,places of religious worship,theaters and exterior lighting zones. ❑ Single zone electronic time control devices and self-contained wall box preset lighting controls. Plans reference page/section: ❑ 15.Exterior lighting controls.Lighting not designated for dusk-to-dawn operation shall be controlled by either a combination of a photosensor and a time switch,or an astronomical time switch.Lighting designated for dusk-to-dawn operation shall be controlled by an astronomical time switch or photosensor. Plans reference page/section: ❑ 16.Tandem wiring.The following luminaires located within the same area shall be tandem wired: 1. Fluorescent luminaires equipped with one,three or odd-numbered lamp configurations,that are recess-mounted within 10 feet center-to-center of each other. 2. Fluorescent luminaires equipped with one,three or any odd-numbered lamp configuration,that are pendant-or surface-mounted within 1 foot edge-to-edge of each other. Exception(s): ❑ Where electronic high-frequency ballasts are used. ❑ Luminaires on emergency circuits. ❑ Luminaires with no available pair in the same area. Plans reference page/section: ❑ 17.Medical task lighting or art/history display lighting claimed to be exempt from compliance has a control device independent of the control of the nonexempt lighting. Plans reference page/section: ❑ 18.Each dwelling unit in a building is metered separately. Plans reference page/section: Interior Lighting PASSES: Design 21%better than code. Section 5: Compliance Statement Compliance Statement: The proposed lighting design represented in this document is consistent with the building plans,specifications and other calculations submitted with this permit application.The proposed lighting system has been designed to meet the 2014 Oregon Energy Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- Efficiency Specialty Code requirements in COMcheck Version 4.0.0 and to comply with the mandatory requirements in the Requirements Checklist. Digitally signed by Alex M.Bargmeyer Alex M. Bargmeyer Alex IVI. Bargmeyer Dace:2015.,22911:33:08-08'00' Name-Title Signature Date Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- COMcheck SoftwareLighting Version 4.0.0 Compliance Certificate Section 1: Project Information Energy Code:2014 Oregon Energy Efficiency Specialty Code Project Title: River Terrace North Pump Station and Force Main Project Type: New Construction Envelope Compliance Method:Simplified Trade-Off Exterior Lighting Zone: 2 (Residentially zoned area) Construction Site: Owner/Agent: Designer/Contractor: 17480 SW Clementine St Mike Kebbe Alex Bargmeyer Beaverton,OR 97007 Clean Water Services Murray,Smith&Assocates, Inc. Section 2: Exterior Lighting Area/Surface Power Calculation A B C D E F Exterior Area/Surface Quantity Allowed Tradable Allowed Proposed Watts Wattage Watts Watts /Unit (B x C) Parking area 3 ft2 0.06 Yes 0 120 Total Tradable Watts'= 0 120 Total Allowed Watts= 0 Total Allowed Supplemental Watts**= 600 Wattage tradeoffs are only allowed between tradable areas/surfaces. **A supplemental allowance equal to 600 watts may be applied toward compliance of both non-tradable and tradable areas/surfaces. Section 3: Exterior Lighting Fixture Schedule A B C D E Fixture ID:Description/Lamp/Wattage Per Lamp/Ballast Lamps/ #of Fixture (C X D) Fixture Fixtures Watt. Parking area(3 ft2):Tradable Wattage LED 2:Type 3:Wall Mounted Light:Other: 1 3 40 120 Total Tradable Proposed Watts= 120 Section 4: Requirements Checklist In the following requirements,blank checkboxes identify requirements that the applicant has not acknowledged as being met. Checkmarks identify requirements that the applicant acknowledges are met or excepted from compliance. 'Plans reference page/section'identifies where in the plans/specs the requirement can be verified as being satisfied. Controls, Switching, and Wiring: 0 1. Lighting designated to operate more than 2000 hours per year for Uncovered Parking Areas shall be equipped with motion sensors that will reduce the luminaire power by thirty-three percent or turn off one-third the luminaires when no activity is detected. Plans reference page/section: Exterior Lighting Restrictions and Exceptions: Li 2. Mercury vapor and incandescent lighting is not permitted for use as exterior lighting. Exception(s): Incandescent lighting controlled by motion sensors and having total power less than 150 watts. LI Incandescent lighting used in or around swimming pools,water features,or other locations subject to the requirements of Article 680 of the National Electric Code. Li 3. Exempt lighting fixtures are equipped with a control device independent of the control of the nonexempt lighting and are identified in Section 3 table above. Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- Plans reference page/section: Section 5: Compliance Statement Compliance Statement: The proposed exterior lighting design represented in this document is consistent with the building plans,specifications and other calculations submitted with this permit application.The proposed lighting system has been designed to meet the 2014 Oregon Energy Efficiency Specialty Code requirements in COMcheck Version 4.0.0 and to comply with the mandatory requirements in the Requirements Checklist. Digitally signed by Alex M.Bargmeyer Alex M. Bargmeyer Alex M. BargmeyerDate:2015.12.2911:33:37-08'00' Name-Title Signature Date Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- COMcheck Software Version 4. 00 Mechanical Complian. ce Certificate Section 1 : Project Information Energy Code:2014 Oregon Energy Efficiency Specialty Code Project Title: River Terrace North Pump Station and Force Main Project Type: New Construction Envelope Compliance Method:Simplified Trade-Off Construction Site: Owner/Agent: Designer/Contractor: 17480 SW Clementine St Mike Kebbe Alex Bargmeyer Beaverton,OR 97007 Clean Water Services Murray,Smith&Assocates,Inc. Section 2: General Information Building Location(for weather data): Tigard,Oregon Climate Zone: 4c Section 3: Mechanical Systems List Quantity System Type&Description 1 HVAC System 1 (Single Zone) : Heating:1 each-Unit Heater,Electric,Capacity=27 kBtu/h No minimum efficiency requirement applies Cooling:1 each-Split System,Capacity=35 kBtu/h,Air-Cooled Condenser,No Economizer,Economizer exception:Computer Room Applications Proposed Efficiency=14.00 SEER,Required Efficiency=13.00 SEER Fan System: FAN SYSTEM 1 I Control Room--Compliance(Motor nameplate HP method) :Passes Fans: FAN 3 Supply,Constant Volume,1190 CFM,0.5 motor nameplate hp 1 HVAC System 2(Single Zone) : Heating:1 each-Duct Furnace,Electric,Capacity=35 kBtu/h No minimum efficiency requirement applies Fan System: FAN SYSTEM 2 I Valve Vault--Compliance(Motor nameplate HP method) :Passes Fans: FAN 4 Supply,Constant Volume,600 CFM,0.2 motor nameplate hp FAN 5 Return,Constant Volume,600 CFM,0.3 motor nameplate hp Section 4: Requirements Checklist In the following requirements,blank checkboxes identify requirements that the applicant has not acknowledged as being met. Checkmarks identify requirements that the applicant acknowledges are met or excepted from compliance. 'Plans reference page/section'identifies where in the plans/specs the requirement can be verified as being satisfied. Requirements Specific To: HVAC System 1 : ❑ 1. Equipment meets minimum efficiency: Split System: 13.00 SEER ❑ 2. Energy recovery ventilation systems.Individual fan systems that have both a design supply air capacity of 5,000 cfm or greater and a minimum outside air supply of 70 percent or greater of the design supply air quantity have an energy recovery system. Exception(s): ❑ Where energy recovery systems are prohibited by the International Mechanical Code. ❑ Systems serving spaces that are not cooled and are heated to less than 60°F. ❑ Where more than 60 percent of the outdoor heating energy is provided from site-recovered or site solar energy. ❑ Type 1 kitchen exhaust hoods. ❑ Cooling systems in climates with a 1-percent cooling design wet-bulb temperature less than 64°F(18°C). Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- Ul Systems requiring dehumidification that employ series-style energy recovery coils wrapped around the cooling coil when the • evaporative coil is located upstream of the exhaust air stream. LI Systems exhausting toxic,flammable,paint exhaust,corrosive fumes,or dust. ILI Laboratory fume hood systems that include qualifying features. Plans reference page/section: u 3. Hydronic system controls.Hydronic systems of at least 300,000 Btu/h design output capacity supplying heated and chilled water to comfort conditioning systems include controls that meet the requirements of Section 503.4.3. Plans reference page/section: Requirements Specific To: HVAC System 2 : O 1. Energy recovery ventilation systems.Individual fan systems that have both a design supply air capacity of 5,000 cfm or greater and a minimum outside air supply of 70 percent or greater of the design supply air quantity have an energy recovery system. Exception(s): Ul Where energy recovery systems are prohibited by the International Mechanical Code. J Systems serving spaces that are not cooled and are heated to less than 60°F. J Where more than 60 percent of the outdoor heating energy is provided from site-recovered or site solar energy. ZI Type 1 kitchen exhaust hoods. LI Cooling systems in climates with a 1-percent cooling design wet-bulb temperature less than 64°F(18°C). J Systems requiring dehumidification that employ series-style energy recovery coils wrapped around the cooling coil when the evaporative coil is located upstream of the exhaust air stream. J Systems exhausting toxic,flammable,paint exhaust,corrosive fumes,or dust. J Laboratory fume hood systems that include qualifying features. Plans reference page/section: Generic Requirements: Must be met by all systems to which the requirement is applicable: u 1. Calculation of heating and cooling loads.Design loads are determined in accordance with the procedures described in the ASHRAE/ACCA Standard 183.Alternatively,design loads have been determined by an approved equivalent computation procedure. • 2. Packaged Electric Equipment.Specified packaged electrical equipment has a heat pump as the primary heating source. Exception(s): • Unstaffed equipment shelters or cabinets used solely for personal wireless service facilities. • Requirement is not applicable. Plans reference page/section: O 3. Equipment and system sizing.Heating and cooling equipment and systems capacity do not exceed the loads calculated in accordance with Section 503.2.1. Exception(s): Ul Required standby equipment and systems provided with controls and devices that allow such systems or equipment to operate automatically only when the primary equipment is not operating. O Multiple units of the same equipment type with combined capacities exceeding the design load and provided with controls that have the capability to sequence the operation of each unit based on load. Plans reference page/section: 0 4. HVAC Equipment Performance Requirements.Reported efficiencies have been tested and rated in accordance with the applicable test procedure.The efficiency has been verified through certification under an approved certification program or,if no certification program exists,the equipment efficiency ratings are supported by data furnished by the manufacturer. • 5. Thermostatic Controls.The supply of heating and cooling energy to each zone is controlled by individual thermostatic controls that respond to temperature within the zone. Plans reference page/section: Li 6. Heat pump supplementary heat.Heat pumps having supplementary electric resistance heat have controls that,except during defrost, prevent supplementary heat operation when the heat pump can meet the heating load. Plans reference page/section: • 7. Set point overlap restriction.Where used to control both heating and cooling,zone thermostatic controls provide a temperature range or deadband of at least 5°F(2.8°C)within which the supply of heating and cooling energy to the zone is capable of being shut off or reduced to a minimum. Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- 1 Exception(s): 0 Thermostats requiring manual change over between heating and cooling modes. Plans reference page/section: O 8. Optimum Start Controls. Each HVAC system has controls that vary the start-up time of the system to just meet the temperature set point at time of occupancy. Plans reference page/section: u 9. Off-hour controls. Each zone is provided with thermostatic setback controls that are controlled by either an automatic time clock or programmable control system. Exception(s): LI Zones that will be operated continuously. LI Zones with a full HVAC load demand not exceeding 6,800 Btu/h(2 kW)and having a readily accessible manual shutoff switch. Plans reference page/section: • 10.Shutoff damper controls.Both outdoor air supply and exhaust are equipped with not less than Class I motorized dampers. Exception(s): LI Gravity dampers shall be permitted for outside air intake or exhaust airflows of 300 cfm or less. Plans reference page/section: • 11.Freeze Protection and Snow melt system controls.Freeze protection systems,such as heat tracing of outdoor piping and heat exchangers,including self-regulating heat tracing,include automatic controls capable of shutting off the systems when outdoor air temperatures meet code criteria. Plans reference page/section: • 12.Separate air distribution systems.Zones with special process temperature requirements and/or humidity requirements are served by separate air distribution systems from those serving zones requiring only comfort conditions;or shall include supplementary control provisions so that the primary systems may be specifically controlled for comfort purposes only. Exception(s): 0 [503.2.4.8+]Zones requiring only comfort heating or comfort cooling that are served by a system primarily used for process temperature and humidity control. Plans reference page/section: • 13.Humidity control. If a system is equipped with a means to add or remove moisture to maintain specific humidity levels in a zone or zones,a humidity control device is provided. Plans reference page/section: • 14.Humidity control.Where a humidity control device exists it is set to prevent the use of fossil fuel or electricity to produce relative humidity in excess of 30 percent.Where a humidity control device is used for dehumidification,it is set to prevent the use of fossil fuel or electricity to reduce relative humidity below 60 percent. Exception(s): p Hospitals,process needs,archives,museums,critical equipment,and other non-comfort situations with specific humidity requirements outside this range. Plans reference page/section: • 15.Humidity control.Where a humidity control device exists it is set to maintain a deadband of at least 10%relative humidity where no active humidification or dehumidification takes place. Exception(s): LI Heating for dehumidification is provided with heat recovery or heat pumping and the mechanical cooling system efficiency is 10 percent higher than required in section 503.2.3, HVAC equipment performance requirements. Plans reference page/section: • 16.Ventilation.Ventilation,either natural or mechanical,is provided in accordance with Chapter 4 of the International Mechanical Code. Where mechanical ventilation is provided,the system has the capability to reduce the outdoor air supply to the minimum required by Chapter 4 of the International Mechanical Code. Plans reference page/section: • 17.Demand controlled ventilation(DCV).DCV is required for spaces larger than 500 ft2 for simple systems and spaces larger than 150 ft2 for multiple zone systems. Exception(s): LI Systems with energy recovery complying with Section 503.2.6 Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- O Spaces less than 750 ft2(69.7 m2)where an occupancy sensor turns the fan off,closes the ventilation damper,or closes the • zone damper when the space is unoccupied. Plans reference page/section: • 18.Kitchen hoods.Kitchen makeup is provided as required by the Oregon Mechanical Specialty Code. Exception(s): O Where hoods are used to exhaust ventilation air that would otherwise be exhausted by other fan systems. O Kitchen exhaust systems that include exhaust air energy recovery complying with section 503.2.6. Plans reference page/section: • 19.Enclosed parking garage ventilation controls.In Group S-2,enclosed parking garages used for storing or handling automobiles employs automatic carbon monoxide sensing devices. Plans reference page/section: • 20.Duct and plenum insulation and sealing.All supply and return air ducts and plenums are insulated with the specified insulation.When located within a building envelope assembly,the duct or plenum is separated from the building exterior or unconditioned or exempt spaces by a minimum of R-8 insulation.All ducts,air handlers and filter boxes are sealed.Joints and seams comply with Section 603.9 of the International Mechanical Code. Exception(s): O When located within equipment. O When the design temperature difference between the interior and exterior of the duct or plenum does not exceed 15°F(8°C). • 21.Low-pressure duct systems.All longitudinal and transverse joints,seams and connections of low-pressure supply and return ducts are securely fastened and sealed with welds,gaskets,mastics(adhesives),mastic-plus-embedded-fabric systems or tapes installed in accordance with the manufacturer's installation instructions. Exception(s): • Continuously welded and locking-type longitudinal joints and seams on ducts operating at static pressures less than 2 inches w.g. pressure classification. Plans reference page/section: u 22.Medium-pressure duct systems.All ducts and plenums designed to operate medium-pressure are insulated and sealed in accordance with Section 503.2.7. Pressure classifications specific to the duct system are clearly indicated on the construction documents. Plans reference page/section: • 23.High-pressure duct systems.Ducts designed to operate at high-pressure are insulated and sealed in accordance with Section 503.2.7. In addition,ducts and plenums are leak-tested in accordance with the SMACNA HVAC Air Duct Leakage Test Manual. Plans reference page/section: • 24.Piping Insulation.All pipes serving space-conditioning systems(hot water piping for heat systems,chilled water,refrigerant,and brine piping systems,and steam piping)are insulated as specified by this section. u 25.Air system balancing. Each supply air outlet and zone terminal device is equipped with means for air balancing in accordance with the requirements of IMC 603.17.Discharge dampers intended to modulate airflow are prohibited on constant volume fans and variable volume fans with motors 10 horsepower. Plans reference page/section: • 26.Hydronic system balancing.Individual hydronic heating and cooling coils are equipped with means for balancing and pressure test connections. Plans reference page/section: • 27.Manuals.The construction documents require that an operating and maintenance manual be provided to the building owner by the mechanical contractor.See long description for specifications. Plans reference page/section: u 28.Air System Design and Control. Each HVAC system having a total fan system motor nameplate hp exceeding 5 hp meets the provisions of Sections 503.2.10.1 through 503.2.10.2. Plans reference page/section: u 29.Allowable fan floor horsepower. Each HVAC system at fan system design conditions does not exceed the allowable fan system motor nameplate hp(Option 1)or fan system bhp(Option 2)as shown and calulated in requirement details. Exception(s): Li Hospital and laboratory systems that utilize flow control devices on exhaust and/or return to maintain space pressure relationships necessary for occupant health and safety or environmental control shall be permitted to use variable volume fan power limitation. Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- ❑ Individual exhaust fans with motor nameplate horsepower of 1 hp or less. Plans reference page/section: ❑ 30.Motor nameplate horsepower.For each fan,the selected fan motor is no larger than the first available motor size greater than the brake horsepower(bhp). Exception(s): j For fans less than 6 bhp,where the first available motor larger than the brake horsepower has a nameplate rating within 50 percent of the bhp,selection of the next larger nameplate motor size is allowed. ❑ For fans 6 bhp and larger,where the first available motor larger than the bhp has a nameplate rating within 30 percent of the bhp, selection of the next larger nameplate motor size is allowed. Plans reference page/section: ❑ 31.Large Volume Fan Systems.Fan systems over 8,000(7 m3/s)cfm without direct expansion cooling coils that serve single zones reduce airflow based on space thermostat heating and cooling demand.A two-speed motor or variable frequency drive reduces airflow to a maximum 60 percent of peak airflow or minimum ventilation air requirement as required by Chapter 4 of the International Mechanical Code,whichever is greater. Exception(s): U Systems where the function of the supply air is for purposes other than temperature control,such as maintaining specific humidity levels or supplying an exhaust system. Plans reference page/section: ❑ 32.AII air-conditioning equipment and air-handling units with direct expansion cooling and a cooling capacity at ARI conditions greater than or equal to 110,000 Btu/h that serve single zones have their supply fan operation controlled according to code specific requirements. Exception(s): ❑ Systems where the function of the supply air is for purposes other than temperature control,such as maintaining specific humidity levels or supplying an exhaust system. Plans reference page/section: ❑ 33.Series fan-powered terminal unit fan motors.Fan motors for series fan-powered terminal units are electronically-commutated motors and have a minimum motor efficiency of 70 percent when rated in accordance with NEMA Standard MG 1-2006 at full load rating conditions. Plans reference page/section: ❑ 34.Heating outside a building.Systems installed to provide heat outside a building are radiant systems.Such heating systems are controlled by an occupancy sensing device or a timer switch,so that the system is automatically deenergized when no occupants are present. Plans reference page/section: ❑ 35.Hot Gas Bypass Limitation.For cooling systems<=240 kBtu/h,maximum hot gas bypass capacity is no more than 50%total cooling capacity. Plans reference page/section: Section 5: Compliance Statement Compliance Statement: The proposed mechanical design represented in this document is consistent with the building plans,specifications and other calculations submitted with this permit application.The proposed mechanical systems have been designed to meet the 2014 Oregon Energy Efficiency Specialty Code requirements in COMcheck Version 4.0.0 and to comply with the mandatory requirements in the Requirements Checklist. Distally signed by Alex M.Bargmeyer Alex M. Bargmeyer Alex IVI. BargmeyerDate:2015.12.29„34:06-08'00' Name-Title Signature Date Section 6: Post Construction Compliance Statement ❑ HVAC record drawings of the actual installation,system capacities,calibration information,and performance data for each equipment provided to the owner. ❑ HVAC O&M documents for all mechanical equipment and system provided to the owner by the mechanical contractor. ❑ Written HVAC balancing and operations report provided to the owner. The above post construction requirements have been completed. Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North- Principal Mechanical Designer-Name Signature Date Project Title: River Terrace North Pump Station and Force Main Report date: 12/29/15 Data filename:G:\PDX_Projects\14\1611 -River Terrace North PS&FM\0204-Final Design\HVAC\River Terrace North-