Loading...
Specifications 4 FP crc c 17 i 622:30 s w P0., ,6� 14,,4iY '' I(00 -. • ' 7 i • VICO Fire & Building Products APR 2 2 2009 CITY OF TIGARD � ' ?' ' 1 r' \I(-`, D i` 1 Technical Services: Tel: (800) 381 -9312 / Fax: (800) 791 -5500 �" ° ' IS ' ® � Series TY -FRB — 2.8, 4.2, t* and 8.0 K- factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage tained when exposed to corrosive at- G eneral mospheres. Although corrosion resis- tant coated sprinklers have passed the �- Description standard corrosion tests of the appli- -`�'` r x "} cable approval agencies, the testing is ...... The Tyco® Series TY -FRB, 2.8, 4.2, not representative of all possible cor- h - 5.6, and 8.0 K- factor, Upright and Pen- rosive atmospheres. Consequently, it1 dent Sprinklers described in this data is recommended that the end user be - sheet are quick response - standard consulted with respect to the suitability i coverage, decorative 3 mm glass bulb of these coatings for any given corro- t:.,. type spray sprinklers designed for use sive environment. The effects of ambi- ! in light or ordinary hazard, commercial ent temperature, concentration of _. - 4 occupancies such as banks, hotels, chemicals, and gas /chemical velocity, IN 4- =., shopping malls, etc. should be considered, as a minimum, The recessed version of the Series along with the corrosive nature of the TY -FRB Pendent Sprinkler, where ap- chemical to which the sprinklers will be plicable, is intended for use in areas exposed._ with a finished ceiling. It uses either a An intermediate level versions of the two -piece Style 10 (1/2 inch NPT) or Series TY -FRB Pendent Sprinklers Style 40 (3/4 inch NPT) Recessed Es- are detailed in Technical Data Sheet ` cutcheon with 1/2 inch (12,7 mm) of TFP356, and Sprinkler Guards are de- 't recessed adjustment or up to 3/4 inch tailed in Technical Data Sheet TFP780 i.. ' i. (19,1 mm) of total adjustment from the - 1 fl pendent position, or a two -piece WARNINGS , ak, T ∎ Style 20 (1/2 inch NPT) or Style 30 (3/4 The Series TY -FRB Sprinklers de- ,�_ - • inch NPT) Recessed Escutcheon with scribed herein must be installed and ■'::f'- • 1/4 inch (6,4 mm) of recessed adjust- maintained in compliance with this ment or up to 1/2 inch (12,7 mm) of document, as well as with the applica- total adjustment from the flush pen- b/e standards of the National Fire Pro - dent position. The adjustment pro- tection Association, in addition to the vided by the Recessed Escutcheon re- standards of any other authorities hay- Model/Sprinkler duces the accuracy to which the fixed ing jurisdiction. Failure to do so may pipe drops to the sprinklers must be impair the performance of these de- Identification cut. vices. Corrosion resistant coatings, where The owner is responsible for maintain- Numbers applicable, are utilized to extend the ing their fire protection system and de- life of copper alloy sprinklers beyond vices in proper operating condition. TY1131 - Upright 2.8K, 1/2 "NPT that which would otherwise be ob- The installing contractor or sprinkler TY1231 - Pendent 2.8K, 1/2 "NPT manufacturer should be contacted TY2131 - Upright 4.2K, 1/2 "NPT with any questions. TY2231 - Pendent 4.2K, 1/2 "NPT IMPORTANT TY3131 - Upright 5.6K, 1/2 "NPT Always refer to Technical Data TY3231 - Pendent 5.6K, 1/2 "NPT Sheet TFP700 for the °INSTALLER TY4131 - Upright 8.0K, 3/4 "NPT WARNING" that provides cautions TY4231 - Pendent 8.0K, 3/4 "NPT with respect to handling and instal- TY4831 Upright 8.0K, 1/2 "NPT lation of sprinkler systems and corn- TY4931 Pendent 8.0K, 1/2 "NPT ponents. Improper handling and in- . stallation can permanently damage a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 10 AUGUST, 2007 TFP171 .4 • Page 2 of 10 TFP171 ESCUTCHEON 7/16° (11,1 mm) STYLE 10 or 20 PLATE SEATING NOMINAL RECESSED SURFACE NPT MAKE-IN ESCUTCHEON DEFECTOR 7 --- ---------------=----------: =--=---------- r te r s 1■r 7/16" ! (57,2 mm) II II (11 mm) jpr I 4 1 IIII NOA ` MAKE -IN MINL 2 1 -9/16" I r I' �� 2- " V 9 3 (39,7 mm) WRENCH 1 3/16 (55,6 mm 66 i ll F LATS = ) 1 Illaif SSP DEFLECTOR * — 2 -7/8" (73,0 mm) DIA. 1/2" NPT PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression 7 - Bushing orifice seat on frame. Screw FIGURE 1 QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY1131) AND PENDENT (TY1231) SPRINKLERS 2.8 K- FACTOR, 1/2 INCH NPT ESCUTCHEON 7/16" (11,1 mm) STYLE 10 or 20 PLATE SEATING NOMINAL RECESSED SURFACE NP MAKE -IN ESCUTCHEON T DEFLECTOR F — —___ 6* 7/16" ,ff„ 5 2 -3/16° ��1rr '� (11,1 mm) (55,6 mm) = 1 /e �� I NOMINAL ■ 4 i MAKE -IN l - 1 -1/2" I 4101 , =� 2-3/16 "� 2 (38,1mm) WRENCH (55,6 mm ) : � t, 1 . _.. . ... FLATS _ 3 I fi SSP DEFLECTOR * r— 2 -7/8" (73,0 mm) DIA. 1/2" NPT PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE 2 QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY2131) AND PENDENT (TY2231) SPRINKLERS 4.2 K- FACTOR, 1/2 INCH NPT J TFP171 Page 3 of 10 • ESCUTCHEON 7/16" (11,1 mm) STYLE 10 or 20 PLATE SEATING NOMINAL RECESSED SURFACE 1/2° PT MAKE -IN ESCUTCHEON DEFLECTOR F .... r 7/16" ��� 2 -3/16" 1� �,� L (11,1 mm) i i (55,6 mm) A = A NOMINAL 4 ���� L 7� 1 MAKE -IN � � 1-1 1/2" . I I' I ∎' i 2 (38,1.mm) + 2 - G� WRENCH (55,6 mm) 0 FLATS �1 • SSP DEFLECTOR * - 2 -7/8" (73,0 mm) DIA. 1/2" NPT f 1 PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw , FIGURE 3 . QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY3131) AND PENDENT (TY3231) SPRINKLERS 5.6 K- FACTOR, 1/2 INCH NPT ESCUTCHEON 1/2" (12,7 mm) STYLE 30 or 40 PLATE SEATING NOMINAL RECESSED SURFACE NP MAKE -IN ESCUTCHEON DEFLECTOR I ` 6 * — - — III 1/2" 5 2 -5/16" (12,7 mm) (58,7 mm) ICI r ` - . NOMINAL I i 4 � ��� I MAKE -IN - II 1- 9/16 ") I I�� 2 -1/4" , V 1� 2 N'm (39,7 mm) WRENCH . (57,2 mm) ,6 Ir FLATS I YY 3 SSP DEFLECTOR 2 -7/8" (73,0 mm) DIA. 3/4" NPT f PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION • 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE 4 QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY4131) AND PENDENT (TY4231) SPRINKLERS 8.0 K- FACTOR, 3/4 INCH NPT Page 4 of 10 TFP171 7/16" (11,1 mm) 1/2" NOMINAL SSU NPT MAKE -IN DEFLECTOR r'rr'r� � ; - /fT!o *offs 6 i ' 5 2 -1/4" — 2 -3/16 i ( 57,2 mm) 1 =�1 I (55,6 6 mm) i4 V 1 -9/16 „ WRENCH !".11 �r 2 _ _ (39,7 mm) FLATS 3 w- - - - - -- SSP* 1 DEFLECTOR CROSS PENDENT UPRIGHT SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw FIGURE 5 QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY4831) AND PENDENT (TY4931) SPRINKLERS 8.0 K- FACTOR, 1/2 INCH NPT Technical Operation Data The glass Bulb contains a fluid which expands when exposed to heat. When Approvals the rated temperature is reached, the . UL and C -UL Listed. fluid expands sufficiently to shatter the FM, LPCB, and NYC Approved. glass Bulb, allowing the sprinkler to (Refer to Table A and B for complete activate and water to flow. approval information including corro- - sion resistant status.) Design Maximum Working Pressure Refer to Table C. Criteria Discharge Coefficient K = 2.8 GPM /psi / (40,3 LPM /bar1 /2) The Series TY -FRB Pendent and Up- K = 4.2 GPM /psi / (60,5 LPM /bar1 /2) right Sprinklers are intended for fire K = 5.6 GPM /psi / (80,6 LPM /bar1 /2) protection systems designed in ac- K = 8.0 GPM /psi / (115,2 LPM /bar1 /) cordance with the standard installation rules recognized by the applicable Temperature Ratings Listing or Approval agency (e.g., UL Refer to Table A and B Listing is based on the requirements of Finishes NFPA 13, and FM Approval is based Sprinkler: Refer to Table A and B. on the requirements of FM's Loss Pre - Recessed Escutcheon: White Coated, vention Data Sheets ). Only the Style Chrome Plated, or Brass Plated. 10, 20, 30, or 40 Recessed Escutch- eon, as applicable, is to be used for recessed pendent installations. Physical Characteristics o Frame Bronze E Button Brass /Copper o Sealing Assembly 2 Beryllium Nickel w /Teflont a Bulb Glass ;, • Compression Screw Bronze 6- Deflector Copper /Bronze 0 Bushing (K =2.8) Bronze 'E a 0 4- TFP171 Page 5 of 10 SPRINKLER FINISH (See Note 7) K TYPE TEMP. BULB NATURAL CHROME WHITE"" LIQUID BRASS PLATED POLYESTER 135 °F /57 °C Orange PENDENT 155 °F /68 °C Red 1231 ) and 175 °F /79 ° C Yellow 1, 2, 3, 5 UPRIGHT 200 °F /93 ° C Green 2.8 (TY1131) 286 °F /141 °C Blue 1/2" NPT 135F/57°C Orange RECESSED 155 °F /68 °C Red PENDENT (TY1231)* 175 °F /79 °C Yellow Figure 6 200F/93°C Green 1, 2, 5 135 °F /57 °C Orange RECESSED 155 °F /68 °C Red PENDENT (TY1231)" 175 °F /79 °C Yellow Figure 7 200 °F /93 °C Green 135 °F /57 °C Orange PENDENT 155 °F /68 °C Red (TY2231) and 175 °F /79 °C Yellow UPRIGHT 200 °F /93 °C Green 4.2 (TY2131) 286 °F /141 °C Blue 1/2" 1, 2 NPT 135 °F /57 °C Orange RECESSED 155 °F /68 °C Red PENDENT (TY2231)• 175 °F /79 ° C Yellow Figure 8 200F/93°C Green 135F/57°C Orange RECESSED 155 °F /68 °C Red PENDENT (TY2231)" 175F/79°C Yellow Figure 9 20OF/93°C Green NOTES: 1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers. 2. Listed by Underwriters Laboratories, Inc. for use in Canada (C -UL) as Quick Re- sponse Sprinklers. 3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprin- klers 5. Approved by the City of New York under MEA 354 -01 -E 7. Where Polyester Coated Sprinklers are noted to be UL and C -UL Listed, the sprin- klers are UL and C -UL Listed as Corrosion Resistant Sprinklers. Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable. " Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable. '•' Frame and Deflector only. Listings and approvals apply to color (Special Order). N /A. Not Available TABLE A LABORATORY LISTINGS AND APPROVALS 2.8 AND 4.2 K- FACTOR SPRINKLERS • Page 6 of 10 TFP171 SPRINKLER FINISH (See Note 8) K TYPE TEMP. BULB NATURAL CHROME WHITE"` LEAD LIQUID BRASS PLATED POLYESTER COATED 135 °F /57 °C Orange PENDENT- 155"F/68°C Red (TY3231) 1, 2, 3, 4, 5, 6, 7 1, 2, 3, 5 and 175 °F /79 °C Yellow UPRIGHT 200"F193°C Green 5 6 (TY3131) 286 °F /141 °C Blue 1/2" NPT 135 °F /57 °C Orange RECESSED 155 °F /68 °C Red PENDENT 1, 2, 4, 5 N/A (TY3231)` 175 °F /79 °C Yellow Figure 10 200 °F /93 °C Green 135"F/57°C Orange RECESSED 155 °F /68 °C Red PENDENT 1, 2, 3, 4, 5 N/A (TY3231)" 175 °F /79 °C Yellow Figure 11 200"F/93°C Green 135 °F /57 °C Orange PENDENT 155 °F /68 °C Red (TY4231) 1, 2, 5 and 175"F/79°C Yellow 1, 2, 3, 4, 5, 6, 7 UPRIGHT 200"F/93°C Green 8.0 (TY4131) 286"F/141°C Blue 3/4" NPT 135"F/57°C Green RECESSED 155 °F /68 °C Orange PENDENT 1, 2, 4, 5 N/A (TY4231)` 175 °F /79 °C Red Figure 12 200"F/93°C Yellow 135 °F /57 °C Orange RECESSED 155 °F /68 °C Red PENDENT 1, 2, 3, 4, 5 N/A (TY4231)" 175 °F /79 °C Yellow Figure 13 200"F/93°C Green 135 °F /57 °C Orange PENDENT 155 °F /68 °C Red 8.0 (TY4931) 1, 2, 5 1/2" and 175 °F /79 °C Yellow 1, 2, 4, 5, 6 NPT UPRIGHT 200 °F /93 °C Green (TY4831) 286 °F /141 °C Blue NOTES: 1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers. 2. Listed by Underwriters Laboratories, Inc. for use in Canada (C -UL) as Quick Response Sprinklers. 3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers 4. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/04) as Quick Response Sprinklers; however, the LPCB does not rate the thermal sensitivity of recessed sprinklers 5. Approved by the City of New York under MEA 354 -01 -E. 6. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31 -53- 428- 4444/Fax 31 -53- 428 - 3377). 7 Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/06) as Quick Response Sprinklers. 8 Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C -UL Listed, the sprinklers are UL and C -UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, the spnnklers are FM Approved as a Corrosion Resistant Sprinklers. • Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable. • " Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable "` Frame and Deflector only. Listings and approvals apply to color (Special Order) N /A: Not Available TABLE B LABORATORY LISTINGS AND APPROVALS 5.6 AND 8.0 K- FACTOR SPRINKLERS TFP171 Page 7 of 10 SPRINKLER FINISH K TYPE NATURAL CHROME WHITE LEAD BRASS PLATED POLYESTER COATED PENDENT (TY3231) and 2 UPRIGHT (TY3131) 175 PSI (12,1 BAR) N/A 1/2" RECESSED PENDENT NPT (TY323) PENDENT (TY4231) and 4 2 UPRIGHT (TY4131) 175 PSI (12,1 BAR) N/A 3/4" RECESSED PENDENT NPT (TY4231) PENDENT (TY3231) and 250 PSI (17,2 BAR) 175 PSI (12,1 BAR) 5.6 UPRIGHT (TY3131) OR 1/2" RECESSED PENDENT 175 PSI (12,1 BAR) NPT (TY3231) (SEE NOTE 1) N/A PENDENT (TY4231) and 175 PSI (12,1 BAR) 175 PSI (12,1 BAR) 8.0 UPRIGHT (TY4131) 3/4" RECESSED PENDENT NPT (TY4231) N/A 8.0 PENDENT (TY4931) 1/2" and 175 PSI (12,1 BAR) 175 PSI (12,1 BAR) NPT UPRIGHT (TY4831) NOTES: . 1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories Inc. (UL); the Listing by Underwriters Laboratories, Inc. for use in Canada (C -UL); and , the Approval by the City of New York. TABLE C, MAXIMUM WORKING PRESSURE tained with a torque of 10 to 20 ft.lbs. the sprinkler into the sprinkler fitting. Installation (13,4 to 26,8 Nm). A maximum of 30 Step 3. Tighten the sprinkler into the ft.lbs. (40,7 Nm) of torque is to be used sprinkler fitting using only the W -Type The Series TY -FRB Sprinklers must to install sprinklers with 3/4 NPT con- 6 Sprinkler Wrench (Ref. Figure 14). be installed in accordance with the fol- nections. Higher levels of torque may With reference to Figures 1, 2, 3, 4, lowing instructions: distort the sprinkler inlet and cause and 5, the W -Type 6 Sprinkler Wrench leakage or impairment of the sprinkler. is to be applied to the sprinkler wrench NOTES Do not attempt to make -up for insuffi- flats. Do not install any bulb type sprinkler if cient adjustment in the escutcheon The Series TY -FRB Recessed Pen - the bulb is cracked or there is a loss of plate by under- or over - tightening the dent Sprinklers must be installed in liquid from the bulb. With the sprinkler sprinkler. Readjust the position of the accordance with the following instruc- held horizontally, a small air bubble should be present. The diameter of the sprinkler fitting to suit. tions. air bubble is approximately 1/16 inch The Series TY -FRB Pendent and Up- Step A. After installing the Style 10. (1,6 mm) for the 135 °F /57 ° C to 3/32 right Sprinklers must be installed in 20, 30, or 40 Mounting Plate, as appli- inch (2,4 mm) for the 286 °F /141 °C accordance with the following instruc- cable, over the sprinkler threads and temperature ratings. tions. with pipe thread sealant applied to the A leak tight 1/2 inch NPT sprinkler joint Step 1. Pendent sprinklers are to be pipe threads, hand tighten the sprin- • should be obtained with a torque of 7 installed in the pendent position, and kler into the sprinkler fitting. to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- upright sprinklers are to be installed in Step B. Tighten the sprinkler into the mum of 21 ft. lbs. (28,5 Nm) of torque the upright position. sprinkler fitting using only the W -Type may be used to install sprinklers with St 2. With pipe thread sealant ap- 7 Recessed Sprinkler Wrench (Ref. ep e 1/2 NPT connections. A leak tight 3/4 St ep 2 the pipe a thr ea, hand tighten Figure 15). With reference to Figure 1, inch NPT sprinkler joint should be ob- 2, 3, and 4, the W -Type 7 Recessed J Page 8 of 10 TFP171 2 -7/8" DIA. 2 -7/8" DIA. 5/8±1/4° (73,0 mm) 3/4" (19,1 mm) 1/211/8" (73,0 mm) 1/2" (12,7 mm) (15,9±6,4 mm) 2.1/4" DIA. 1/4" (6,4 mm) (12,7±3,2 mm) 2 -1/4" DIA. 1/4" (6,4 mm) FACE OF (57,2 mm) MOUNTING FACE OF (57,2 mm) MOUNTING SPRINKLER PLATE SPRINKLER PLATE FITTING FITTING 1/8" 1/8" _ •; , (3,2 mm) •� (3 mm) � � r r xlli % , 1 A .. - _ l ` 0/ f , MOUNTING � SURFACE J J . SURFACE --� *-! '. i v *-■-a-� CLOSURE SERIES 1 -5/16° (33,3 mm) CLOSURE SERIES 1 -5116° (33,3 mm) TY -FRB 13/16" (20.6 mm) TY -FRB 1 -1 /16" (27,0 mm) FIGURE 6 FIGURE 7 SERIES TY -FRB RECESSED PENDENT SERIES TY -FRB RECESSED PENDENT WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON 2.8 K- FACTOR, 1/2 INCH NPT 2.8 K- FACTOR, 1/2 INCH NPT 2 -7/8" DIA. 2 -7/8° DIA. 5/8±1/4" (73,0 mm) 3/4" (19,1 mm) (73,0 mm) 1/2±1/8" 1/2" (12,7 mm) (15,9±6,4 mm) 2 -1/4° DIA. 1/4° (6,4 mm) (12,7±3,2 mm) 2 -1/4" DIA. 1/4° (6,4 mm) FACE OF (57,2 mm) MOUNTING FACE OF (57,2 mm) MOUNTING SPRINKLER PLATE SPRINKLER PLATE FITTING FITTING 1/8' 1/8" -1 � ' ' (3,2 mm) 2. � (3,2 mm) -J M NTIN t OU G MO UNTING �, SURFA � SURFACE - • -- - • - CLOSURE SERIES 1 -1/4" (31,8 mm) CLOSURE SERIES 1 -1/4" (31,8 mm) TY -FRB 3/4" (19,1 mm) TY-FRB 1° (25,4 mm) FIGURE 8 FIGURE 9 SERIES TY -FRB RECESSED PENDENT SERIES TY -FRB RECESSED PENDENT WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON 4.2 K- FACTOR, 1/2 INCH NPT 4.2 K- FACTOR, 1/2 INCH NPT Sprinkler Wrench is to be applied to work on the fire protection system that altered after leaving the factory. Modi- the sprinkler wrench flats. it controls, permission to shut down the fied sprinklers must be replaced. Step C. After the ceiling has been in- affected fire protection system must be Sprinklers that have been exposed to stalled or the finish coat has been ap- obtained from the proper authorities corrosive products of combustion, but plied, slide on the Style 10, 20, 30, or and all personnel who may be affected have not operated, should be replaced 40 Closure over the Series TY-FRB by th act must be not if they cannot be completely cleaned Sprinkler and push the Closure over The owner must assure that the sprin- by wi the sprinkler with a cloth or the Mounting Plate until its flange klers are not used for hanging of any by brush i t w a soft br brush. comes in contact with the ceiling. objects; otherwise, non - operation in Care must be exercised to avoid dam - the event of a fire or inadvertent opera- age to the sprinklers - before, during, are and tion may result. and after installation. Sprinklers dam - Absence of an escutcheon, which is aged by dropping, striking, wrench used to cover a clearance hole, may twist/slippage, or the like, must be re- Maintenance delay the time to sprinkler operation in placed. Also, replace any sprinkler The Series TY -FRB Sprinklers must a fire situation. that has a cracked bulb or that has lost P liquid from its bulb. (Ref. Installation tallation ' be maintained and serviced in accord- Sprinklers that are found to be leaking Section). ance with the following instructions: or exhibiting visible signs of corrosion must be replaced. Frequent visual inspections are rec- NOTES ommended to be initially performed for • Before closing a fire protection system Automatic sprinklers must never be corrosion resistant coated sprinklers, main control valve for maintenance painted, plated, coated or otherwise after the installation has been corn- : TFP171 Page 9 of 10 - 2 -7/8" DIA. 2 -7/8" DIA. (73,0 mm) (19,1 mm) (73,0 mm) 3/4° 5/811/4" ( ) 1/211/8° 1/2" (12.7 mm) (15,936,4 mm) 2 -1/4" DIA. 1/4" (6,4 mm) (12,713,2 mm) 2 -1/4" DIA. 1/4° (6,4 mm) FACE OF (57,2 mm) MOUNTING FACE OF (57,2 mm) MOUNTING SPRINKLER PLATE SPRINKLER PLATE FITTING FITTING 1/8' 1/8' (3,2 mm) � ) 1 i p• i ; ' k , �, 1 ■ MOUNTING �,�' MOUNTING I SURFACE SURFACE - i.___ _ A _. ; CLOSURE SERIES 1 -1/4" (31,8 mm) CLOSURE SERIES 1 -1/4" (31,8 mm) TY -FRB 3/4" (19,1 mm) TY-FRB 1° (25,4 mm) FIGURE 10 FIGURE 11 SERIES TY -FRB RECESSED PENDENT SERIES TY -FRB RECESSED PENDENT WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON 5.6 K- FACTOR, 1/2 INCH NPT 5.6 K- FACTOR, 1/2 INCH NPT 2 -7/8" DIA. 2 -7/8" DIA. 5/811/4" (73,0 mm) 3/4' (19,1 mm) 1/21118" (73,0 mm) 1/2° (12,7 mm) (15,916,4 mm) 2 -1/4" DIA. 1/4" (6,4 mm) (12,713,2 mm) 2 -1/4" DIA. 1/4° (6,4 mm) FACE OF (57,2 mm) MOUNTING FACE OF (57,2 mm) MOUNTING SPRINKLER PLATE SPRINKLER PLATE FITTING FITTING 1/8" 1/8' � (3,2 mm) Ww="---'011; (3,2 m JJA ' � V f , MOUNTING 1I MOUNTING SURFACE . SURFACE • ' CLOSURE SERIES 1 -5/16' (33,3 mm) CLOSURE SERIES 1 -5/16" (33,3 mm) TY -FRB 13/16' (20,6 mm) TY-FRB 1 -1/16" (27,0 mm) FIGURE 12 FIGURE 13 SERIES TY -FRB RECESSED PENDENT SERIES TY -FRB RECESSED PENDENT WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON STYLE 30 RECESSED ESCUTCHEON 8.0 K- FACTOR, 3/4 INCH NPT 8.0 K- FACTOR, 3/4 INCH NPT pleted, to verify the integrity of the cor- L WRENCH rosion resistant coating. Thereafter, a RECESS annual inspections per NFPA 25 should suffice; however, instead of in- WRENCH RECESS giro specting from the floor level, a random (END "A" USED FOR �� sampling of close -up visual inspec- 1/2" NPT MODELS) tions should be made, so as to better � determine the exact sprinkler condi- S° 0 tion and the long term integrity of the �.., corrosion resistant coating, as it may WRENCH RECESS PUSH WRENCH be affected by the corrosive conditions (END "B" USED FOR IN TO ENSURE present. 3/4" NPT MODELS) ENGAGEMENT The owner is responsible for the in- FIGURE 14 WRENCHING AREA spection, testing, and maintenance of W - TYPE 6 SPRINKLER their fire protection system and de- WRENCH FIGURE 15 vices in compliance with this docu- W - TYPE 7 RECESSED - ment, as well as with the applicable SPRINKLER WRENCH facturer should be contacted relative standards of the National Fire Protec- to any questions. tion Association (e.g., NFPA 25), in Inspection Service in accordance with addition to the standards of any other It is recommended that automatic local requirements and /or national authorities having jurisdiction. The in- sprinkler systems be inspected, codes. stalling contractor or sprinkler manu- tested, and maintained by a qualified • • Page 10 of 10 TFP171 P/N 57 - XXX - X - XXX I I TEMPERATURE MODEUSIN RATING SPRINKLER - 330 2.8K UPRIGHT (1/2 "NPT) TY1131 135 135 °F /57 °C 331 2.8K PENDENT (1/2 "NPT) TY1231 1 NATURAL BRASS 155 155 °F /68 °C 340 4.2K UPRIGHT (1/2 "NPT) TY2131 4 WHITE POLYESTER 175 175F/79°C 341 4 2K PENDENT (1/2 "NPT) TY2231 3 WHITE (RAL9010)' 200 200 °F /93 °C 370 5.6K UPRIGHT (1/2"NPT) TY3131 9 CHROME PLATED 286 2B6F/141°C 371 5.6K PENDENT (1/2 "NPT) TY3231 7 LEAD COATED 390 8.0K UPRIGHT (3/4 "NPT) TY4131 391 8.0K PENDENT (3/4 "NPT) TY4231 • Eastern Hemisphere sales only 360 8.0K UPRIGHT (1/2 "NPT) TY4831* 361 8.0K PENDENT (1/2 "NPT) TY4931' TABLE D PART NUMBER SELECTION SERIES TY -FRB PENDENT AND UPRIGHT SPRINKLERS In no event shall TFBP be liable, in Ordering Limited contract, tort, strict liability or under any other legal theory, for incidental, Warranty indirect, special or consequential dam- Procedure ages, including but not limited to labor Products manufactured by Tyco Fire & charges, regardless of whether TFBP When placing an order, indicate the Building Products (TFBP) are war- was informed about the possibility of full product name. Refer to the Price ranted solely to the original Buyer for such damages, and in no event shall List for complete listing of Part Num- - ten (10) years against defects in mate- TFBP's liability exceed an amount bers. rial and workmanship when paid for equal to the sales price. Contact your local distributor for avail - and properly installed and maintained under normal use and service. This The foregoing warranty is made in lieu ability. warranty will expire ten (10) years of any and all other warranties. ex- from date of shipment by TFBP. No press or implied. including warranties Sprinkler Assemblies with NPT warranty is given for products or corn - of merchantability and fitness for a oar- Thread Connections: ponents manufactured by companies ticular purpose. Specify: (Specify Model /SIN), Quick Response, (specify K- factor), (specify not affiliated by ownership with TFBP This limited warranty sets forth the ex- temperature rating), Series TY -FRB or for products and components which clusive remedy for claims based on (specify Pendent or Upright) Sprinkler have been subject to misuse, improper failure of or defect in products, materi- with (specify type of finish or coating), installation, corrosion, or which have als or components, whether the claim P/N (specify from Table D). not been installed, maintained, modi- is made in contract, tort, strict liability fled or repaired in accordance with ap- or any other legal theory. Recessed Escutcheon: plicable Standards of the National Fire Specify: Style (10, 20, 30, or 40) Re- Protection Association, and /or the This warranty will apply to the full ex- P fY tY ( ) standards of any other Authorities tent permitted by law. The invalidity, in cessed Escutcheon with (specify) fin - Having Jurisdiction. Materials found whole or part, of any portion of this ish, P/N (specify "). by TFBP to be defective shall be either warranty will not affect the remainder. repaired or replaced, at TFBP's sole Refer to Technical Data Sheet TFP770. option. TFBP neither assumes, nor Sprinkler Wrench: authorizes any person to assume for it, Specify: W -Type 6 Sprinkler Wrench, any other obligation in connection with P/N 56- 000 -6 -387. the sale of products or parts of prod- ucts. TFBP shall not be responsible for Specify: W -Type 7 Sprinkler Wrench, sprinkler system design errors or inac- P/N 56- 850 -4 -001. curate or incomplete information sup- . plied by Buyer or Buyer's repre- sentatives. TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 . . Vito Fire & Building Products Technical Services: Tel: (800) 381 -9312 / Fax: (800) 791 -5500 Series TY -B — 2.8, 5.6 and 8.0 K- factor Upright, Pendent, an Recessed Pendent Sprinklers Standard Response, Standard Coverage General cable approval agencies, the testing is ' not representative of all possible cor- _ Description rosive atmospheres. Consequently, it ' °` KF _ • is recommended that the end user be 1 . -, -- "� consulted with respect to the suitability , :. >.,,` ,• The Series TY -B, 2.8, 5.6, and 8.0 of these coatings for any given corro- a 1 ; 4 K- factor, Upright and Pendent Sprin- sive environment. The effects of ambi- { f t klers described in this data sheet are ent temperature, concentration of standard response - standard cover- chemicals, and gas /chemical velocity, age, decorative 5 mm glass bulb type should be considered, as a minimum, spray sprinklers designed for use in along with the corrosive nature of the x light, ordinary, or extra hazard, corn- chemical to which the sprinklers will be mercial occupancies such as banks, exposed. . . • - hotels, shopping malls, factories, refin- eries, chemical plants, etc. An intermediate level version of the Series TY -B Pendent Sprinkler can be The recessed version of the Series obtained by utilizing the Series TY -B h TY -B Pendent Sprinkler, where appli- Pendent Sprinkler in combination with cable, is intended for use in areas with the Model S2 Shield. :. , a finished ceiling. It uses a two -piece . r Style 10 (1/2 inch NPT) or Style 40 (3/4 WARNINGS rc inch NPT) Recessed Escutcheon. The The Series TY-B Sprinklers described Recessed Escutcheon provides 1/2 herein must be installed and main - inch (12,7 mm) of recessed adjust- tained in compliance with this docu- ment or up to 3/4 inch (19,1 mm) of ment, as well as with the applicable total adjustment from the flush pen- standards of the National Fire Protec- dent position The adjustment pro- tion Association, in addition to the vided by the Recessed Escutcheon re- standards of any other authorities hay- �`'1.,; - , duces the accuracy to which the fixed ing jurisdiction. Failure to do so may ' , - r „.K pipe drops to the sprinklers must be impair the performance of these de- cut. vices. Corrosion resistant coatings, where The owner is responsible for maintain - applicable, are utilized to extend the ing their fire protection system and de- life of copper alloy sprinklers beyond vices in proper operating condition. that which would otherwise be ob- The installing contractor or sprinkler tained when exposed to corrosive at- manufacturer should be contacted mospheres. Although corrosion resis- with any questions. tant coated sprinklers have passed the standard corrosion tests of the appli- Model /Sprinkler IMPORTANT Identification Always refer to Technical Data Sheet TFP700 for the "INSTALLER Numbers WARNING” that provides cautions with respect to handling and instal- TY1151 - Upright 2.8K, 1/2"NPT lation of sprinkler systems and corn- TY1251 - Pendent 2.8K, 1/2 "NPT / ponents. Improper handling and in- TY3151 - Upright 5.6K, 1/2 "NPT C� • stallation can permanently damage TY3251 - Pendent 5.6K, 1/2 "NPT a sprinkler system or its compo- TY4151 - Upright 8.0K, 3/4 "NPT nents and cause the sprinkler to fail TY4251 - Pendent 8.0K, 3/4 "NPT to operate in a fire situation or cause TY4851 - Upright 8.0K, 1/2"NPT it to operate prematurely. TY4951 - Pendent 8.0K, 1/2 "NPT Page 1 of 8 DECEMBER, 2007 TFP151 Page 2 of 8 TFP151 . ESCUTCHEON 7/16" (11,1 mm) PLATE SEATING 1/2 „ ** NOMINAL SSU - SURFACE NPT MAKE -IN DEFLECTOR • + 6 • t t - ir1� } :,,'r1 -711. ,'TT ,, 5 • . \ I 2 -1/4” 1 —� 2 -3/16" (57,2 mm) I =, ' (55,6 mm) 4 1 -9/16 ' WRENCH M IMI 6' , i 3 (39,7 mm) FLATS I ;6 1 ! s� 7 of SSP 7 . DEFLECTOR CROSS PENDENT UPRIGHT SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression 7 - Bushing orifice.seat on frame. Screw * * Pipe thread connections per ISO 7/1 can be provided on special request. - FIGURE 1 STANDARD RESPONSE SERIES TY -8 UPRIGHT (TY1151) AND PENDENT (TY1251) SPRINKLERS 2.8 K- FACTOR, 1/2 INCH NPT ESCUTCHEON 7/16" (11,1 mm) STYLE 10 PLATE SEATING 1/2" ** NOMINAL RECESSED SURFACE MAKE -IN ESCUTCHEON SSU* NPT I DEFLECTOR 5 :// ///T1r Ry . /:,i77��s.j rr 7/16" � 2 -3/16" 1 .11'� (11.1 mm) • - (55,6 mm) t A= A ��- NOMINAL I. i 4 _ `_ MAKE -IN • 1-1/2" RIP ��� `� 2-3/16" ...r F� 2 (38,1 mm WRENCH (55,6 mm) y 3 l = f,/ ■ 1 - �_��.:- - FLATS = / ¢ . 1 SSP DEFLECTOR 2 -7/8" (73,0 mm) DIA. --I 1/2" NPT ** PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw * * Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 2 STANDARD RESPONSE SERIES TY-B UPRIGHT (TY3151) AND PENDENT (TY3251) SPRINKLERS 5.6 K- FACTOR, 1/2 INCH NPT • TFP151 Page 3 of 8 • ESCUTCHEON 1/2" (12,7 mm) . STYLE 40 PLATE SEATING ** NOMINAL RECESSED SURFACE NP MAKE -IN ESCUTCHEON T DEFLECTOR — — , * 6 T --- — 1/2 . �% 5 2- 5/16" `� 'F M (12,7 mm) (58,7 mm) I1�A NOMINAL 4 ce _ 1 L J I MAKE 1 -9/16" 2 -1/4" A 1 !o 2 (39,7 mm) id , I �� (57,2 mm) O � � y WRENCH l 0 3 1 - -- • - -- -.. - - ° --- FLA 1 �S iz 1 SSP DEFLECTOR - - 2 -7/8" (73,0 mm) DIA. - " { 3/4" NPT PENDENT . RECESSED PENDENT UPRIGHT CROSS SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjace to 2 - Button Assembly 5• Compression .• orifice seat on frame. Screw • • _ * * Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 3 • STANDARD RESPONSE SERIES TY -B UPRIGHT (TY4151)-AND PENDENT (TY4251) SPRINKLERS 8.0 K- FACTOR, 3/4 INCH NPT • ESCUTCHEON 7/16" (11,1 mm) PLATE SEATING 1/2" ** NOMINAL SSU SURFACE NPT MAKE -IN DEFLECTOR \ _„_- — .- 1 ., 6 t — ______ _ r'r '�'v 1..% s, irol 5 2-1/4" 2 -3/16" (57,2 mm) I. r .. (55,6 mm) 4 1 -9/16" WRENCH de V '0I 2 (39,7 mm) FLATS 7 L • SSP 1 DEFLECTOR CROSS PENDENT UPRIGHT SECTION 1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to 2 - Button Assembly 5 - Compression orifice seat on frame. Screw * * Pipe thread connections per ISO 7/1 can be provided on special request. FIGURE 4 STANDARD RESPONSE SERIES TY -B UPRIGHT (TY4851) AND PENDENT (TY4951) SPRINKLERS 8.0 K- FACTOR, 1/2 INCH NPT • Page 4 of 8 TFP151 • - SPRINKLER' FINISH (See Note 8)- - • . K TYPE TEMP. BULB NATURAL CHROME WHITE° ° LEAD WAX . WAX OVER , LIQUID BRASS PLATED POLYESTER - COATED • COATED LEAD COATED 135 °F /57 °C Orange • PENDENT 155 °F /68 °C Red • 2.8 (TY1251) 1, 2, 3 N/A 1/2" and 175"F179°C Yellow . NPT UPRIGHT 200 °F /93 °C Green (TY1151) 286 °F /141 °C Blue 360 °F /182 °C Mauve 1, 2 135 °F /57 °C Orange PENDENT 155 °F /68 °C Red (TY3251) 1, 2, 3, 4, 5, 6, 7 1, 2, 3, 5 1, 2, 3, 5 1, 2, 3, 5 and 175 °F /79 °C • Yellow UPRIGHT 200 °F /93 °C _ ..Green • 5.6 (TY3151) 286 °F /141 °C Blue 1 ",2 ", 3", 5" 1", 2 ", 3", 5" 1/2" • • NPT 360 °F /182 °C •Mauve - • I • N/A - . 135 °F /57 °C Orange - - _ RECESSED 155 °F /68 °C Red PENDENT 1, 2, 3, 4, 5 N/A - (TY3251)° 175 °F /79 °C Yellow • Figure 4 200 °F /93 °C Green 286 °F /141 °C Blue 1, 2 • 135 °F /57 °C Orange PENDENT 155 °F /68 °C Red (TY4251) 1,2,5 1,2,3,5 1,2,5 and 175 °F /79 °C Yellow 1, 2, 3, 4, 5, 6, 7 8 0 UPRIGHT 200 °F /93 °C Green 3/4° (TY4151) • 286 °F /141 °C Blue 1 ",2'° 3°' 5" I 1« 2« 5** NPT 360 °F /182 °C . Mauve I N/A ' 135 °F /57 °C Orange RECESSED - . 155°F/68°C _ Red • PENDENT 1,2,3,4,5 N/A (TY4251)° , 175'F/79°C Yellow • Figure 5 200 °F /93 °C Green 286 °F /141. °C Blue 1, 2 135 °F /57 °C Orange PENDENT 155 °F /68 °C Red 8.0 (TY 1/2" and 175 °Fl79 °C Yellow 1, 2, 3, 4, 5, 6 N/A NPT UPRIGHT 200 °F /93 °C Green (TY4851) 286 °F /141 °C - Blue 360 °F /182 °C Mauve NOTES: 1. Listed by Underwriters Laboratories, Inc. (UL). 2. Listed by Underwriters Laboratories, Inc. for use in Canada (C -UL). 3. Approved by Factory Mutual Research Corporation (FM). 4. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/03). 5. Approved by the City of New York under MEA 354 -01 -E. 6. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31- 53- 428- 4444/Fax 31 -53 -428- 3377). 7. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/05). 8. Where Polyester Coated, Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted to be UL and C -UL Listed, the sprinklers are UL and C -UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as Corrosion Resistant Sprinklers. • Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4° Total Adjustment Recessed Escutcheon, as applicable. °° 150 °F /66 °C Maximum Ceiling Temperature. ° °° Frame and deflector only. Listings and approvals apply to color (Special Order). TABLE A, LABORATORY LISTINGS AND APPROVALS • • TFP151 Page 5 of 8 • • - SPRINKLER FINISH K TYPE NATURAL CHROME WHITE LEAD WAX WAX OVER BRASS PLATED POLYESTER COATED COATED LEAD COATED 2.8 - PENDENT (TY1251) 1/2" and 175 PSI (12,1 BAR) N/A NPT UPRIGHT (TY1151) PENDENT (TY3251) 5.6 and 250 PSI (17,2 BAR) 175 PSI (12,1 BAR) 1/2" UPRIGHT (TY3151) OR NPT RECESSED PENDENT= 175 PSI (12,1 BAR) (1Y3251) (SEE NOTE 1) N/A 8.0 PENDENT(TY4251) 3/4" and 175 PSI (12,1 BAR) NPT UPRIGHT (TY4151) • • RECESSED PENDENT (TY4251) 175 PSI (12,1 BAR) N/A • 8.0 PENDENT(TY4951) 1/2" and 175 PSI (12,1 BAR) NPT UPRIGHT (TY4851) NOTE: 1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories, Inc. (UL); the Listing by Underwriters Laboratories, Inc. for use in Canada (C -UL); and, the Approval by the City of New York. TABLE B, MAXIMUM WORKING PRESSURE Technical .Operation Data The glass Bulb contains a fluid which expands when exposed to heat. When Approvals .. the rated temperature is reached, 'the • UL and C -UL Listed. fluid expands sufficiently shatter the FM, LPCB „VdS, and NYC Approved. glass Bulb, allowing the sprinkler to • (Refer to •Table--A for complete ap- activate and water to flow. proval information including corrosion resistant status.) Design' Maximum Working Pressure Refer to Table B. Criteria Discharge Coefficient • K = 2.8 GPM /psi (40,3 LPM /bar1/2) The Series TY -B Pendent and Upright K = 5.6 GPM /psi / (80,6 LPM /bar1/2 Sprinklers are intended for fire protec- K = 8.0 GPM /psi / (115,2 LPM /bar1 /2 ) tion systems designed in accordance with the standard installation rules rec- Temperature Ratings ognized by the applicable Listing or Refer to Table A. Approval agency (e.g., UL Listing is Finishes based on the requirements of NFPA Sprinkler: Refer to Table A. 13, and FM Approval is based on the Recessed Escutcheon: White Coated, requirements of FM's Loss Prevention Chrome Plated, or Brass Plated. Data Sheets). Only the Style 10 or 40 E Recessed Escutcheon, as applicable, Physical Characteristics is to be used for recessed pendent Frame Bronze installations. '— Button Brass /Copper Sealing Assembly m • Beryllium Nickel w/Teflont y Bulb Glass Compression Screw Bronze Deflector Copper ° Bushing (K =2.8) Bronze } • Page 6 of 8 TFP151 • • 2 -7/8" DIA. , 5/8±1/4" (73,0 mm) 3/4" (19,1 mm) (15,9±6,4 mm) 2 -1/4" DIA. 1/4" (6,4 mm) WRENCH RECESS FACE OF (57,2 mm) MOUNTING ^ (E 1/2" NPT MODELS) SPRINKLER • PLATE • FITTING 1/8" WRENCH RECESS •�' (3,2 mm) (END "B" USED FOR 3/4" NPT MODELS) / ✓ � 1 FIGURE 7 W -TYPE 6 SPRINKLER e J, WRENCH MOUNTING SURFACE — • - WRENCH CLOSURE SERIES 1 -1/4" (31,8 mm) RECESS TY-B 3/4" (19,1 mm) • - j HrIP TIIP. FIGURE 5 SERIES TY -B RECESSED PENDENT SPRINKLER ASSEMBLY WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON 5.6 K- FACTOR, 1/2 INCH NPT PUSH WRENCH IN TO ENSURE 2 -7/8" DIA. ENGAGEMENT (73,0 mm) 3/4" (19,1 mm) WITH SPRINKLER 5/8±1/4" WRENCHING AREA • (15,9±6,4 mm) 2 -1/4" DIA. 1/4" (6,4 mm) (57,2 mm) FIGURE 8 FACE OF MOUNTING W -TYPE 7 RECESSED SPRINKLER PLATE • SPRINKLER WRENCH FITTING • 1/8" - • rlllj (3,2 mm) Installation. • The Series TY -B Sprinklers must be � I , — installed in accordance with the follow - � in instructions: MOUNTING NOTES SURFACE • Do not install any bulb type sprinkler if - - - -- - the bulb is cracked or there is a loss of CLOSURE SERIES 1 -5/16" (33,3 mm) liquid from the bulb. With the sprinkler TY-B 13/16" 20,6 mm) held horizontally, a small air bubble ( ) should be present. The diameter of the air bubble is approximately 1/16 inch FIGURE 6 (1,6 mm) for the 135"F/57°C to 3/32 SERIES TY -B RECESSED PENDENT SPRINKLER ASSEMBLY inch (2,4 mm) for the 360 °F /182 °C temperature ratings. WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON A 1/2 inch NPT sprinkler joint should 8.0 K- FACTOR, 3/4 INCH NPT be obtained with a minimum to maxi- mum torque of 7 to 14 ft.lbs. (9,5 to 19,0 Nm). A 3/4 inch NPT sprinkler joint should be obtained with a mini- mum to maximum torque of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). Higher levels • of torque may distort the sprinkler inlet and cause leakage or impairment of the sprinkler. Do not attempt to make -up for insuffi- cient adjustment in the escutcheon plate by under- or over - tightening the TFP151 Page 7 of 8 sprinkler. Readjust the position of the The Series TY -B Recessed Pendent and after installation. Sprinklers dam - sprinkler fitting to suit. Sprinklers must be installed in ac- aged by dropping, striking, wrench The Series TY -B Pendent and Up- cordance with the following instruc- twist/slippage, or the like, must be re- right Sprinklers must be installed in tions. • placed. Also, replace any sprinkler accordance with the following instruc- Step A. After installing the Style 10 or that has a cracked bulb or that has lost tions. 40 Mounting Plate, as applicable, over liquid from its bulb. (Ref. Installation Section). the sprinkler• threads and with pipe Step 1. Pendent sprinklers are to be thread sealant applied to the pipe Frequent visual inspections are rec- installed in the pendent. position, and threads, hand tighten the sprinkler into ommended to be initially performed for upright sprinklers are to be installed in the sprinkler fitting. corrosion resistant coated sprinklers, the upright position. after the installation has been com- Step 2. With pipe thread sealant a - Step B . Tighten the sprinkler into the , to plie to the pipe threads, hand tighten sprinkler fitting using only the W -Type r on res stant ngr Thereafter, the sprinkler into the sprinkler fitting. 7 Recessed Sprinkler Wrench (Ref. annual inspections per NFPA 25 Figure 8). With reference to Figure 3 should suffice; however, instead of in- Step 3. Tighten the sprinkler into the or 4, the W -Type 7 Recessed Sprinkler s hould g from the floor level, instead a random sprinkler fitting using only the W -Type Wrench is to be applied to the sprinkler sampling. of close -up visual inspec- 6 Sprinkler Wrench (Ref. Figure 7), wrench flats. except that an.8 or 10 inch adjustable tions should be made, so as to better • Crescent wrench is to be used for wax Step C. After. the ceiling has been in- determine the exact sprinkler condi- coated sprinklers. With reference to stalled or the finish coat has been ap- tion and the long term integrity of the Figures 1, 2, 3, and 4 the W -Type to plied, slide on the Style 10 or 40 Clo- corrosion resistant coating, as it may Sprinkler Wrench or the adjustable sure over the Series TY -B Sprinkler be affected by the corrosive conditions Crescent wrench, as applicable is to and push the Closure over the Mount- present: - be applied to the wrench flats. ing Plate until its flange comes in con- : • tact with the ceiling. The owner is responsible for the in- When installing wax coated sprinklers spection, testing,'and maintenance of with the adjustable Crescent wrench, their fire protection system and de- additional care needs to be exercised C are a n d vices in compliance with this docu- to prevent damage to the wax coating ment, as well as with the applicable on the sprinkler wrench flats or frame M a i n t enance standards of the National Fire Protec- arms and, consequently, exposure of tion Association (e.g., NFPA 25), in bare metal to the corrosive environ- The Series TY -B Sprinklers must be addition to the standards of any other ment. The jaws of the wrench should maintained and serviced in accord- authorities having jurisdiction. The in- be opened sufficiently wide to pass ance with the following instructions: stalling contractor or sprinkler menu- over the wrench flats without damag- N OTES facturer should be contacted relative ing the wax coating. Before wrench to any questions. tightening the sprinkler, the jaws of the Before closing a fire protection system ' wrench are to be adjusted to just con- main control valve for maintenance Automatic sprinkler systems should be tact the sprinkler wrench flats. After work on the fire protection system that inspected, tested, and maintained by wrench tightening the sprinkler, loosen it controls, permission to shut down the a .qualified Inspection Service• in ac- the wrench jaws before removing the affected fire protection system must be cordance with local requirements wrench. obtained from. the proper authorities and /or national codes. • and all personnel who may be'affected ' After installation, the sprinkler wrerich by this action must be notified. .' ' • flats and frame arms must be iri- spected and the wax coating re- The owner must assure that the sprin- touched (repaired) whenever the coat- klers are not used for hanging of any ing has been damaged and bare metal objects; otherwise, non - operation in is exposed. The wax coating on the the event of a fire or inadvertent opera - wrench flats can be retouched by gen -- tion may result. tly applying a heated 1/8 inch diameter Absence of an escutcheon, which is steel rod to the areas of wax that have used to cover a clearance hole, may been damaged, to smooth it back over delay the time to sprinkler operation in areas where bare metal is exposed. a fire situation. NOTES Sprinklers that are found to be leaking Only retouching of the wax coating ap- or exhibiting visible signs of corrosion plied to the wrench flats and frame must be replaced. arms is permitted, and the retouching Automatic sprinklers must never be is t� be performed only at the time of painted, plated, coated or otherwise the initial sprinkler installation. altered after leaving the factory. Modi- The steel rod should be heated only to fied sprinklers must be replaced. the point at which it can begin to melt Sprinklers that have been exposed to the wax, and appropriate precautions corrosive products of combustion, but - need to be taken, when handling the have not operated, should be replaced heated rod, in order to prevent the if they cannot be completely cleaned installer from being burned. by wiping the sprinkler with a cloth or by brushing it with a soft bristle brush. Care must be exercised to avoid dam- age to the sprinklers - before, during, Page 8 of 8 TFP151 •P /N 57 -XXX -X -XXX • SPRINKLER TEMPERATURE • MODEUSIN RATING 530 2.8K UPRIGHT (1/2 "NPT) TY1151 1 NATURAL BRASS 135 135 °F /57 °C • 531 .2.8K PENDENT (1/2 "NPT) " TY1251 4 WHITE POLYESTER 155 155 °F /68 °C 570 5.6K UPRIGHT (1/2 "NPT) TY3151 3 WHITE (RAL9010) • 175 175 °F /79 °C 571 5.6K PENDENT (1/2 "NPT) TY3251 9 CHROME PLATED 200 200 °F /93 °C • 590 8.0K UPRIGHT (3/4 "NPT) TY4151 7 LEAD COATED 286 286 °F /141 °C 591 8.0K PENDENT (3/4 "NPT) TY4251 6 WAX COATED 360 360 °F /182 °C • 286 °F /141 °C MAX. 560 8.0K UPRIGHT (1/2 "NPT) TY4851 8 WAX OVER LEAD 561 8.0K PENDENT (1/2 "NPT) TY4951 286 °F /141 °C MAX. • • Eastern Hemisphere sales only. TABLE C PART NUMBER SELECTION SERIES TY -B PENDENT AND UPRIGHT SPRINKLERS any other legal theory, for incidental, Limited indirect, special or consequential dam- Ordering Warranty ages, including but not limited to labor charges, regardless of whether TFBP Procedure was informed about the possibility of Products manufactured by Tyco Fire & such damages, and in no event shall When placing an order, indicate the Building Products (TFBP) are war- TFBP's liability exceed an amount full product name. Refer to the Price ranted solely to the original Buyer for equal to the sales price. List for complete listing' of Part Num- . ten (10) years against defects in mate- bers. • rial and workmanship when paid for The foregoing warranty is made in lien . - and properly installed and maintained of any and all other -warranties. ex- Contact your local distributor for avail - under normal use and service. This press or implied. including warranties ability. - warranty will expire ten (10) years of merchantability and fitness fora par - from date of shipment by TFBP. No Iicular`purpose.. Sprinkler Assemblies with NPT • Thread Connections: warranty is given for products or corn- This limited warranty sets forth the ex - Specify: (Specify Model /SIN), Stand - ponents manufactured by companies clusive remedy for claims based on and Response, (specify K- factor), not affiliated by ownership with TFBP failure of or defect in products, materi- (specify temperature rating), Series or for products and components which als or components, whether the claim TY -B (specify Pendent or Upright) have been subject to misuse, improper is made in contract, tort, strict liability Sprinkler with (specify type of finish or installation, corrosion, or which have or any other legal theory. coating), P/N (specify from Table C). not been installed, maintained, modi- . fled or repaired in accordance with ap- This warranty will apply to the full ex- plicable Standards of the National Fire tent permitted by law. The invalidity, in Recessed Escutcheon: Protection Association, and /or the whole or part, of any portion of this Specify: Style (specify 10 or 40 ) Re- standards of any other Authorities warranty will not affect the remainder. cessed Escutcheon with (specify *) fin- Having Jurisdiction. Materials found ish, P/N (specify *). by TFBP to be defective shall be either • Refer to Technical Data Sheet TFP770. repaired or replaced, at TFBP's sole option. TFBP neither assumes, nor Sprinkler Wrench: authorizes any person to assume for it, Specify: W -Type 6 Sprinkler Wrench, any other obligation in connection with P/N 56- 000 -6 -387. the sale of products or parts of prod- ucts. TFBP shall not be responsible for Specify: W -Type 7 Sprinkler Wrench, sprinkler system design errors or inac P/N 56 -850 -4 -001. curate or incomplete information sup- plied by Buyer or Buyer's repre- sentatives. • In no event shall TFBP be liable, in contract, tort, strict liability or under © 2007 TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446 IF/re t qcn &Building , J ... ,, , , , ,`, Products APR 2 2 2009 9 . ,.., I ` Technical Services: Tel: (800) 381 -9312 / Fax: (800) 791-5500 r ;�; � �: .r Series EC -11 & EC -14 — 11.2 and 14.0 K- factor Extended Coverage (Light and Ordinary Hazard) Upright, Pendent, and Recessed Pendent Sprinklers Corrosion resistant coatings, where General applicable, are utilized to extend the life of copper alloy sprinklers beyond Description that which would otherwise be ob- - tained when ex osed to corrosive at- " r� i mospheres. Although corrosion resis- The Tyco® Series EC -11 and EC -14 pr y f� te- Extended Coverage Upright and Pen- tant coated sprinklers have passed the r dent Sprinklers are decorative glass standard corrosion tests of the appli- ' • °..} , l bulb sprinklers designed for use in cable approval agencies, the testing is ; . ___..1 light or ordinary hazard occupancies. not representative of all possible cor- They are intended for use in automatic rosive atmospheres. Consequently, it v ^ - , + sprinkler systems designed in accord- is recommended that the end user be ' ° ,., ance with standard installation rules consulted with respect to the suitability - = r s (e.g., NFPA 13) for a maximum cover- of these corrosion resistant coatings age area of 400 ft (37,2 m as corn- for any given corrosive environment. pared to the maximum coverage area The effects of ambient temperature, of 130 ft (12,1 m for standard cover- concentration of chemicals, and age sprinklers used in ordinary haz- gas /chemical velocity, should be con- . and occupancies or 225 ft (20,6 m sidered, as a minimum, along with the for standard coverage sprinklers used corrosive nature of the chemical to in light hazard occupancies. which the sprinklers will be exposed. The Series EC -11 and EC -14 Sprin- - , .."\ klers feature a UL and C -UL Listing WARNINGS ; The Series EC -11 and EC -14 Ex- �u• � !` that permits their use with unob- tended Covera eS rinklersdescribed i i• , w.t. structed or non - combustible ob- g p structed ceiling construction as de- herein must be installed and main • } . fined and permitted by NFPA 13, as tamed in compliance with this docu well as a specific application listing for ment, as well as with the applicable use under concrete tees. standards of the National Fire Protec . tion Association, in addition to the - The Series EC -11 and EC -14 Ex- standards of any other authorities hav- tended Coverage Sprinklers have ing jurisdiction. Failure to do so may been fire tested to compare their per- impair the performance of these de ce to that of standard coverage vices. spray Model /Sprinkler spray sprinklers. These tests have shown that the protection provided is The owner is responsible for maintain - equal to or more effective than stand- ing their fire protection system and de - Identification and coverage spray sprinklers. vices in proper operating condition. The installing contractor or sprinkler Number manufacturer should be contacted with any questions. TY5137 - Upright, 11.2K IMPORTANT TY5237 - Pendent, 11.2K Always refer to Technical Data TY6137 - Upright, 14.0K Sheet TFP700 for the "INSTALLER TY6237 - Pendent,14.0K WARNING° that provides cautions TY5137 is a redesignation for C5137, with respect to handling and instal G1894, and S2510. lation of sprinkler systems and com- ponents. Improper handling and in- TY5237 is a redesignation for C5237, - stallation can permanently damage G1893, and S2511. a sprinkler system or its compo- nents and cause the sprinkler to fail G 1896, is a redesignation for C6137, to operate in a fire situation or cause G 1896, and S2610. - it to operate prematurely. TY6237 is a redesignation for C6237, G1895, and S2611. Page 1 of 8 DECEMBER, 2007 TFP220 Page 2 of 8 TFP220 WRENCH 3/4" ** ESCUTCHEON PLATE FLAT NPT SEATING SURFACE 1 1 - Frame r --- AB 2 - Button ,tre-i�ti : ,� 2 3 - Sealing Assembly ray& 4- Bulb 5 - Compression Screw >■11 6 - Deflector • � N 3 2-7/16" 1 il l ' Pil 11111 i (61,9 mm) •Temperature rating is I UPRIGHT & indicated on deflector PENDENT 1 I 1 4 ** Pipe thread �� kao (42,7 mm) \ 1 connections per ISO � �: 5 7/1 can be provided -_ :��_ on special request. — = — — — — — --- a i.- ' 6* 1/2" (12,7 mm) J NOMINAL MAKE -IN CROSS UPRIGHT PENDENT SECTION FIGURE 1 SERIES EC -11 AND EC -14 EXTENDED COVERAGE SPRINKLERS 11.2 K- FACTOR (TY5137) UPRIGHT AND (TY5237) PENDENT 14.0 K- FACTOR (TY6137) UPRIGHT AND (TY6237) PENDENT SPRINKLER FINISH (See Note 5) HAZARD TYPE TEMP. BULB NATURAL CHROME WHITE' LEAD LIQUID BRASS PLATED POLYESTER COATED 135 °F /57 °C Orange UPRIGHT 155 °F /68 °C Red 1, 2, 3", 4 LIGHT K =11.2 (TY5137) PENDENT 175"F/79°C Yellow K =11.2 (TY5237) 200 °F /93 °C Green 1, 2, 4 1, 2, 4 Refer to Table B for K =14.0 (TY6237) . UL and C -UL 286"F/141°C Blue Sensitivity Rating 135 °F /57 °C Orange and REC. PENDENT 155 °F /68 °C Red 1, 2, 3, 4 Refer to Table C for K =11.2 (TY5237) N/A - FM K =14.0 (TY6237) 175"F/79°C Yellow Sensitivity Rating With Style 30 200 °F /93 °C Green 1, 2, 4 Escutcheon • 286 °F /141 °C Blue UPRIGHT 135 °F /57 °C Orange K =11.2 (TY5137) 1, 2, 3, 4 ORDINARY K =14.0 (TY6137) 155 °F /68 °C Red 1, 2, 3, 4 and 175 °F /79 °C Yellow Refer to Table B for PENDENT 200 °F /93 °C Green 1, 2, 4 UL and C -UL K =11.2 (TY5237) Sensitivity Rating K =14.0 (TY6237) 286 °F /141 °C Blue and REC. PENDENT 135 °F /57 °C Orange Refer to Table C for K =11.2 (TY5237) 155 °F /68 °C Red FM K =14.0 (TY6237) 1, 2, 4 N/A Sensitivity Rating With Style 40 175 °F /79 °C Yellow Escutcheon 200 °F /93 °C Green NOTES: 1.Listed by Underwriters Laboratories, Inc. (UL). 2.Listed by Underwriters Laboratories, Inc. for use in Canada (C -UL). 3. Approved by Factory Mutual Research Corporation (FM). 4. Approved by the City of New York under MEA 177 -03 -E. 5. Where Polyester Coated or Lead Coated Sprinklers are noted to be UL and C -UL Listed, the sprinklers are UL and C -UL Listed as Corrosion Resistant Sprinklers. 'Frame and Deflector only. Listings and approvals apply to color (Special Order). " Pendent Only N /A: Not Available TABLE A, LABORATORY LISTINGS AND APPROVALS TFP220 • Page 3 of 8 LIGHT HAZARD ORDINARY HAZARD 135 °F 155 °F 175 °F 200 °F 286 °F 135 °F 155 °F 175 °F 200 °F 286 °F AREA STYLE 14 x 14 Up. or Pend. — — — — — QR QR QR OR SR 14 x 14 Style 30 Recessed — — — — — QR QR QR QR N/A 14 x 14 Style 40 Recessed — — — — — QR OR QR QR N/A 16 x 16 Up. or Pend. OR QR• OR OR OR* SR SR SR SR SR 16 x 16 Style 30 Recessed OR* OR OR* OR* OR* SR SR SR SR N/A 16 x 16 Style 40 Recessed N/A N/A N/A N/A N/A SR SR SR SR N/A 18 x 18 Up. or Pend. OR* OR* OR* OR QR* SR SR SR SR SR 18 x 18 Style 30 Recessed OR* OR* OR* OR* OR* SR SR SR SR N/A 18 x 18 Style 40 Recessed N/A N/A N/A N/A N/A SR SR SR SR N/A 20 x 20 Up. or Pend. OR OR OR* SR* SR* SR SR SR SR SR 20 x 20 Style 30 Recessed OR SR* QR* SR* SR* SR SR SR SR N/A 20 x 20 Style 40 Recessed N/A N/A N/A N/A N/A SR SR SR SR N/A QR: Quick Response SR: Standard Response N /A: Not Applicable • Does not apply to Upright K = 14.0 TABLE B SENSITIVITY RATING FOR UL AND C -UL LISTING OF SERIES EC -11 OR EC -14 SPRINKLERS (SEE TABLED FOR PERMITTED K- FACTOR/AREA COMBINATIONS) LIGHT HAZARD ORDINARY HAZARD 135 °F 155 °F 175 °F 200 °F 286 °F 135 °F 155 °F 175 °F 200 °F 286 °F AREA STYLE 14 x 14 Up. or Pend. — — — — — SR SR SR SR SR 14 x 14 Style 30 Recessed — — — — — N/A N/A N/A N/A N/A 14 x 14 Style 40 Recessed — — — — — N/A N/A N/A N/A N/A 16 x 16 Up. or Pend. OR OR* N/A N/A N/A SR SR SR SR SR 16 x 16 Style 30 Recessed QR QR N/A N/A N/A N/A N/A N/A N/A N/A 16 x 16 Style 40 Recessed N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 18 x 18 Up or Pend. QR* QR* N/A N/A N/A SR SR SR SR SR 18 x 18 Style 30 Recessed QR QR N/A N/A N/A N/A N/A N/A N/A N/A 18 x 18 Style 40 Recessed N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 20 x 20 Up or Pend. QR* OW N/A N/A N/A SR SR SR SR SR 20 x 20 Style 30 Recessed QR QR N/A N/A N/A N/A N/A N/A N/A N/A 20 x 20 Style 40 Recessed N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A OR: Quick Response SR: Standard Response N /A: Not Applicable • Pendent Only TABLE C • SENSITIVITY RATING FOR FM APPROVAL OF SERIES EC -11 OR EC -14 SPRINKLERS (SEE FM LOSS PREVENTION DATA SHEET 2 -8N FOR PERMITTED K- FACTOR/AREA COMBINATIONS) • Page 4 of 8 TFP22O Technical Operation Sprinklers, prevent m) cold solder- ( ing, is 8 feet (2,4 m) for uprAright s slderprin- klers and 9 feet (2,7 m) for pendent Data The glass bulb contains a fluid which sprinklers. expands when exposed to heat. When Approvals the rated temperature is reached, the 5. The Series EC -11 and EC -14 Sprin - The Series EC -11 and EC -14 Ex- fluid expands sufficiently to shatter the klers are to be installed in accord - tended Coverage Upright, Pendent, glass bulb, which then allows the ance with all other requirements of and Recessed Pendent Sprinklers are sprinkler to activate and flow water. NFPA 13 for extended coverage up- UL and C -UL Listed. (Refer to Table A right and pendent sprinklers. For ex- for complete sprinkler approval infor- ample: obstructions to sprinkler dis- mation including corrosion resistant Design charge, obstructions to sprinkler status. The approvals apply to the C pattern development, obstructions service conditions indicated in the De- to prevent sprinkler discharge from sign Criteria section.) The Tyco® Series EC -11 and EC -14 reaching hazard, clearance to stor- The Series EC -11 and EC -14 Ex- Extended Coverage Sprinklers must age, etc. tended Coverage Upright and Pendent only be installed in accordance with Sprinklers are FM Approved. (Refer to the applicable UL and C -UL Listing or L and e Speci Application Table A for complete sprinkler ap- FM Approval requirements as indi- Lsting Reququrements For proval information including corrosion cated below. Only the Style 30 or 40 I nstallation U nder Concrete Tees resistant status. The approvals apply Recessed Escutcheon is to be used for The Series and Ent to the service conditions indicated in recessed installation, as applicable tended Coveraage ge U Upright annd d P Pe endent the Design Criteria section.) (Ref. Table A, B, and C). Sprinklers (TY5137, TY5237, TY6137 have a & TY6237) have a UL and C -UL Spe- The Style 60 Two -Piece Flush Es- UL and C -UL Listing cific Application Listing for use under cutcheon (Ref. Figure 4) is UL Listed Requirements concrete tees when installed as fol- and FM Approved for use with the Se- lows: ries EC -11 and EC -14 Pendent Sprin- 1. The Series EC -11 and EC -14 Sprin- klers. klers may be used for the coverage 1. The stems of the concrete tee con - Maximum Working Pressure areas shown in Table D, based on struction must spaced at less than 175 psi (12,1 bar) maintaining the minimum specified 7.5 feet (2,3 m) on center but more flow rate as a function of coverage than 3 feet (0,9 m) on center. The Pipe Thread Connection area and hazard group for all of the depth of the concrete tees must not 3/4 inch NPT sprinklers in the design area. exceed 30 inches (762 mm). The Discharge Coefficients maximum permitted concrete tee K = 11.2 GPM /psi112 2. The Series EC -11 and EC -14 Sprin- length is 32 feet (9,8 m); however, (161,3 LPM /bar112) klers are permitted to be used with where the concrete tee length ex- • K = 14.0 GPM /psi1 /2 unobstructed or non - combustible ceeds 32 feet (9,8 m), non- combus- (201,6 LPM /barlI2) obstructed ceiling construction as tible baffles, equal in height to the defined and permitted by NFPA 13. depth of the tees, can be installed so Temperature Ratings For example: that the space between the tees 135 °F /57 °C to 286 °F /141 °C does not exceed 32 feet (9,8 m) in Finish Unobstructed, combustible or non- length. Sprinkler: Refer to Table A combustible, ceiling construction • Recessed or Flush Escutcheon: White with a deflector to ceiling /roof deck 2. The sprinkler deflectors are to be Coated, Chrome Plated, and Brass distance of 1 to 12 inches (25 to 300 located in a horizontal plane at or Plated mm). above 1 inch (25,4 mm) below the bottom of the concrete tee stems. Physical Characteristics Obstructed, non - combustible, ceil- Frame Bronze ing construction with a deflector lo- 3. When the sprinkler deflectors are Button Bronze cation below structural members of located higher than a horizontal Sealing Assembly 1 to 6 inches (25 to 150 mm) and a plane 1 inch (251,4 mm) beneath the Beryllium Nickel w/Teflon t maximum deflector to ceiling /roof bottom of the concrete tee stems, Bulb Glass (3 mm dia.) deck distance of 22 inches (550 the obstruction to sprinkler dis- Compression Screw mm). charge criteria requirements of Bronze NFPA 13 for extended coverage up- Deflector Brass 3. The Series EC -11 and EC -14 Sprin- right sprinklers applies. klers having been specifically tested and listed for non - combustible ob- FM Approval Patents structed construction are permitted Requirements U.S.A. Patent Numbers 5,366,022; to be used within trusses or barjoists The Series EC -11 and EC -14 Ex- 5,579,846; 5,584,344; 5,609,211; having non - combustible web mem- tended Coverage Sprinklers are to be 5,862,994; and 5,865,256. bers greater than 1 inch (25.4 mm) installed in accordance with the appli- when applying the 4 times obstruc- cable Factory Mutual Loss Prevention tion criteria rule defined under "Ob- Data Sheet for limited use in buildings structions to Sprinkler Discharge of specific roof construction and for the Pattern Development ". protection of certain specific ordinary hazard (non- storage and /or non -flam- 4. The minimum allowable spacing be- mable or combustible liquid) occupan- tween the Series EC -11 and EC -14 cies. Information provided in the FM TFP22O Page 5 of 8 Loss Prevention Data Sheets relate to, but are not limited to, hydraulic design, 2 -7/8" DIA. ceiling slope and obstructions, mini - 1/2±1/8" (73,0 mm) 1/2" (12,7 mm) mum and maximum allowable spec- (12,7±3,2 mm) 2 -1/4" DIA. 1/4" (6,4 mm) ing, and deflector -to ceiling distance. FACE OF (57,2 mm) These criteria may differ from UL SPRINKLER 1/8" and /or NFPA criteria, therefore the de- FITTING (3,2 mm) signer should review and become fa- miliar � b with ments before proceeding Factory Mutual with require . design � = I l -- It } Installation MOUNTING SURFACE MOUNTING PLATE The Series EC -11 and EC -14 Sprin- CLOSURE �I klers must be installed in accordance -• - -_ - - -- with the following instructions: 1 -3/8" (34,9 mm) NOTES 1 - 1/8" (28,6 mm) Do not install any bulb type sprinkler if the bulb is cracked or there is a loss of liquid from the bulb. With the sprinkler FIGURE 2 held horizontally, a small air bubble SERIES EC -11 AND EC -14 RECESSED PENDENT SPRINKLER ASSEMBLY should be present. The diameter of the WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT air bubble is approximately 1/16 inch inch mm) for the for 28 to 3/32 STYLE 30 RECESSED ESCUTCHEON inch (2,4 mm) for the 286 °F /141 °C temperature ratings. A 3/4 inch NPT sprinkler joint should be obtained with a minimum to maxi- mum torque of 10 to 20 ft.lbs. (13,4 to 26,8 Nm). Higher levels of torque may 2 DIA. distort the sprinkler inlet with conse- 5/8±1/4" (73,0 mm) 3/4" (19,1 mm) quent leakage or impairment of the sprinkler. (15,916,4 mm) 2 - 1/4" DIA. 1/4" (6,4 mm) FACE OF (57,2 mm) Do not attempt to compensate for in SPRINKLER 1/8" sufficient adjustment in an Escutcheon FITTING (3,2 mm) Plate by under- or over - tightening the il position of the sprinkler fitting to ust sui t. rl' Step 1. The sprinkler must be installed with the deflector parallel to the mount- It ing surface. Pendent sprinklers must } be installed in the pendent position, MOUNTING � MOUNTING and upright sprinklers must be in- SURFACE PLATE stalled in the upright position. CLOSURE Step 2. After installing the Style 30, 40, 1 -3/8" (34,9 mm) or 60 mounting plate (or other escutch- 7/8" (22,2 mm) eon, as applicable) over the sprinkler pipe threads and with pipe thread sealant applied to the pipe threads, hand tighten the sprinkler into the FIGURE 3 sprinkler fitting. SERIES EC -11 AND EC -14 RECESSED PENDENT SPRINKLER ASSEMBLY Step 3. Wrench tighten upright or pen - WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT dent sprinklers using only the W -Type STYLE 40 RECESSED ESCUTCHEON 3 (End A) Sprinkler Wrench. When in- stalling the pendent sprinkler with Style 30, 40, or 60 Escutcheon, wrench tighten the sprinkler using only the W -Type 22 Sprinkler Wrench. The wrench recess of the applicable sprin- kler wrench (Ref. Figure 5 and 6) is to • be applied to the sprinkler wrench flats (Ref. Figure 1). Page 6 of 8 TFP220 • 2-7/8 DIA. "FITTING SIDE" (73,0 mm) TOWARDS SPRINKLER INTERNAL FITTING 2 -1/4" DIA. -1/4 DIA. DIMENSIONS OF (57,2 STYLE 60 ESCUTCHEON IIIM ACCOMMODATE - t le CLASS 150 MALLEABLE 1 FACE OF IRON REDUCING SPRINKLER FITTING: SPRINKLER FITTING 3/8" (9,5 mm)ABOVE MOUNTING / WRENCH TO 1/8" (3,2 mm) BELOW RECESS MOUNTING SURFACE 7 1/8 SURFACE ) (3,2 mm) (END "A ") ESCUTCHEON PLATE — L pill. • FIGURE 5 SEATING SURFACE IIIIL CLOSURE ' W - TYPE 3 SPRINKLER 1/4" (6,4 mm) ABOVE I 2- 5/16" (58,7 mm) WRENCH TO 1/2" (12,7 mm) BELOW 3/4" NPT MOUNTING SURFACE, k__,• MOUNTING 1-13/16" (46,0 mm) 3/4" (19,1 mm) TOTAL PLATE WRENCH ADJUSTMENT - -_- -' " RECESS iL yi► FIGURE 4 SERIES EC -11 AND EC -14 PENDENT SPRINKLER ASSEMBLY r WITH 3/4 INCH TOTAL ADJUSTMENT �' ' �� STYLE 60 TWO -PIECE FLUSH ESCUTCHEON '8' I'�I� : — kii0 cZI o Care and twist/slippage, or the like, must be re- 1 1 II placed. Also, replace any sprinkler that WRENCH has a cracked bulb or that has lost HEX Maintenance liquid from its bulb. (Ref. Installation Section). FIGURE 6 The Tyco® Series EC -11 and EC -14 W - TYPE 22 RECESSED • Sprinklers must be maintained and Frequent visual inspections are rec- SPRINKLER WRENCH serviced in accordance with the follow- ommended to be initially performed for ing instructions: corrosion resistant coated sprinklers, after the installation has been corn- - NOTE pleted, to verify the integrity of the cor- ance with local requirements and /or Before closing a fire protection system rosion resistant coating. Thereafter national codes. main control valve for maintenance annual inspections per NFPA 25 work on the fire protection system that should suffice; however, instead of in- it controls, permission to shut down the specting from the floor level, a random affected fire protection systems must sampling of close-up visual inspec- be obtained from the proper authori tions should be made, so as to better ties and all personnel who may be determine the exact sprinkler condi- affected by this action must be notified. tion and the long term integrity of the corrosion resistant coating, as it may be affected by the corrosive conditions Sprinklers that are found to be leaking present. or exhibiting visible signs of corrosion must be replaced. The owner is responsible for the in- spection, testing, and maintenance of Automatic sprinklers must never be their fire protection system and de- painted, plated, coated, or otherwise vices in compliance with this docu- altered after leaving the factory. Modi- ment, as well as with the applicable fied sprinklers must be replaced. standards of the National Fire Protec- Sprinklers that have been exposed to tion Association (e.g., NFPA 25), in corrosive products of combustion, but addition to the standards of any other have not operated, should be replaced authorities having jurisdiction. The in- if they cannot be completely cleaned stalling contractor or sprinkler manu- by wiping the sprinkler with a cloth or facturer should be contacted relative by brushing it with a soft bristle brush. to any questions. Care must be exercised to avoid dam- Automatic sprinkler systems should be age to the sprinklers - before, during, inspected, tested, and maintained by a and after installation. Sprinklers dam- qualified Inspection Service in accord - aged by dropping, striking, wrench • TFP220 Page 7 of 8 • GROUP I GROUP II LIGHT HAZARD ORDINARY HAZARD ORDINARY HAZARD 0.10 GPM /FT 0.15 GPM /FT 0.20 GPM /FT DESCRIPTION AREA GPM PSI GPM PSI GPM PSI TY5137 (K =11.2) UPRIGHT 14 x 14 - - 30 7 2 39 12 1 16 x 16 30 7.2 39 12.1 51 20.7 18 x 18 33 8.7 49 19.1 65 33.7 20 x 20 40 12.8 60 28 7 80 51.0 TY5237 (K =11.2) PENDENT 14 x 14 - - 30 7.2 39 12.1 16 x 16 30 7.2 39 12.1 51 20.7 18 x 18 33 8.7 49 19.1 65 33.7 20 x 20 40 12.8 60 28.7 80 51.0 TY6137 (K =14.0) UPRIGHT 14 x 14 N/A N/A - - - - 16 x 16 N/A N/A 39 7.8 51 13.3 18 x 18 N/A N/A 49 12.3 65 21.6 20 x 20 N/A N/A 60 18.4 80 32.7 TY6237 (K =14.0) PENDENT 14 x 14 - - - - - - 16 x 16 37 7.0 39 7.8 51 13.3 18 x 18 37 7.0 49 12.3 65 21.6 20 x 20 40 8.2 60 18.4 80 32.7 1 ft. = 0.3048 m 1 ft = 0 093 m 1 gpm = 3.785 Ipm 1 psi = 0.06895 bar 1 gpm/ft = 40.74 mm /min TABLE D FLOW CRITERIA FOR UL AND C -UL LISTING OF SERIES EC -11 AND EC -14 SPRINKLERS sprinkler system design errors or inac- Li mited curate or incomplete information sup- . Warranty plied by Buyer or Buyer's repre- sentatives. Products manufactured by Tyco Fire & no event shall TFBP be liable, in Building Products (TFBP) are war- contract, tort, strict liability or under ranted solely to the original Buyer for any other legal theory, for incidental, ten (10) years against defects in mate- indirect, special or consequential dam - rial and workmanship when paid for ages, including but not limited to labor and properly installed and maintained charges, regardless of whether TFBP under normal use and service. This was informed about the possibility of warranty will expire ten (10) years such damages, and in no event shall from date of shipment by TFBP. No TFBP's liability exceed an amount warranty is given for products or com- equal to the sales price. ponents manufactured by companies The foregoing warranty is made in lieu not affiliated by ownership with TFBP of any and all other warranties. ex- or for products and components which press or implied. including warranties have been subject to misuse, improper of merchantability and fitness for a par - installation, corrosion, or which have ticular purpose. not been installed, maintained, modi- fied or repaired in accordance with ap- This limited warranty sets forth the ex- plicable Standards of the National Fire clusive remedy for claims based on Protection Association, and /or the failure of or defect in products, materi- standards of any other Authorities als or components, whether the claim Having Jurisdiction. Materials found is made in contract, tort, strict liability by TFBP to be defective shall be either or any other legal theory. repaired or replaced, at TFBP's sole This warranty will apply to the full ex- option. TFBP neither assumes, nor tent permitted by law. The invalidity, in authorizes any person to assume for it, whole or part, of any portion of this any other obligation in connection with warranty will not affect the remainder. the sale of products or parts of prod- ucts. TFBP shall not be responsible for • Page 8 of 8 • TFP22O Ordering P/N 51 - AAA - B -CCC Procedure AAA = 893 (for TY5237 When placing an order, indicate the full K11.2 Pendent) product name. Please specify the AAA = 894 (for TY5137 Sprinkler Identification Number (SIN), K11.2 Upright) quantity, and temperature rating. Re- AAA = 895 (for TY6237 fer to the Price List for complete listing • K14.0 Pendent) of Part Numbers. AAA = 896 (for TY6137 Contact your local distributor for avail- K14.0 Upright) ability. Sprinkler Assemblies with NPT B = 1 (for Natural Brass) Thread Connections: B = 3 (for White [RAL9010])* Specify: (specify SIN), (specify K -Fac- B = 4 (for White Polyester) tor), (specify temperature rating), B = 7 (for Lead Coated (specify Pendent or Upright) Extended B = 9 (for Chrome Plated) Coverage Sprinkler with (specify fin - ish), P/N (specify - from Table E, where applicable). CCC = 135 (for 135 °F /57 °C) CCC =155 (for 155 °F /68 °C) Recessed Escutcheon, Two -Piece : CCC = 175 (for 175 °F /79 °C) Specify: Style (30 or 40) Two -Piece CCC = 200 (for 200 °F /93 °C) Recessed Escutcheon with (specify material or finish'), P/N (specify). *Eastern Hemisphere sales only. *Refer to Technical Data Sheet TFP770. TABLE E PART NUMBERS FOR Flush Escutcheon, Two -Piece : EC - 11 AND EC - 14 SPRINKLERS Specify: Style 60 Two -Piece Flush Es- cutcheon with (specify finish'), P/N (specify). *Refer to Technical Data Sheet TFP778. Sprinkler Wrench: Specify: W -Type 3 Sprinkler Wrench, • P/N 56- 895 -1 -001 Specify: W -Type 22 Recessed Sprin- kler Wrench, P/N 56- 665 -7 -001 • • © TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446