The URL can be used to link to this page

Report Fp82o19-cam //71?6c/ 07 GL 4,4 BE 4077 Airpark Dr. Standish, MI 48658 •989-846-4583•www.globesprinkler.com FIRE SPRINKLER CORPORATION Technical Support•989-414-2600•techservice@globesprinkler.com SPECIFIC APPLICATION MODEL "IC" INTERSTITIAL COMBUSTIBLE CONCEALED SPACE UPRIGHT SPRINKLER GL5608 RECEIVED GENERAL DESCRIPTION The Globe Series GL-SS/IC GL5608 Interstitial Combustible JAN 7 2020 Space Sprinkler is a quick response, upright, specific appli- cation sprinkler designed to provide protection of light haz- ` CITY OF TIGARD and combustible and non-combustible concealed spaces, dUILDING DIVISION inclusive of interstitial (between floors) or attic spaces (with slopes 2:12 or less). Each GL5608 sprinkler can be de- signed for up to 16ft x 16ft (4.9m x 4.9m) spacing, providing as much as 256 ft2 (23.8m2)of protection per sprinkler. The GL5608 sprinkler meets the requirements of Under- writers Laboratories UL 199H to comply with criteria for the protection of combustible concealed spaces as described in ----- NFPA —NFPA 13. < When heat is absorbed, liquid within the glass bulb ex- pands, increasing the internal pressure. At the prescribed temperature the internal pressure within the ampule ex- ceeds the strength of the glass causing the glass to shatter. GL 608 This results in water discharge which is distributed in an ap- proved V a!V pattern. • APPLICATION SERIES GL—SS/IC UPRIGHT The GL-SS/IC GL5608 can be designed for installation in SPRINKLER: CPVC wet pipe sprinkler systems and steel wet pipe or dry pipe sprinkler systems. The GL5608 can be used in The Globe GL-SS/IC GL5608 Interstitial Combustible Up- concealed spaces having roof pitch of 2 in 12 or less con- right Sprinkler has been Listed to be used beyond the 36" structed of wood truss, non-combustible bar joist, solid (914.4mm) height to a height of 60" (1.5m) to provide more wood joists, or composite wood joists. The specific design functionality in installation specifically in areas where the requirements for each type of piping system, and construc- height of the concealed space is both above and below the tion materials can be found in the following sections of this height of 36" (914.4mm). document. NFPA 13 REQUIREMENTS TECHNICAL DATA • cULus Listed for coverage areas up to 256 ft2 (23.8 m2) Sprinklers shall be Listed for use in combustible concealed • 16 ft (4.9 m) maximum and 6 ft (1.8 m) minimum spaces (with a slope not exceeding 2 in 12) with combus- Sprinkler Spacing tible wood truss, wood joist construction, or bar joist con- • Maximum Open Space Height 60 in (1.5 m) struction having a combustible upper surface and where the • Temperature Ratings- 175°F (79°C), 200°F (93°C) depth of the space is less than 36" (914.4mm) from deck to deck or with double wood joist and composite wood joist • Finish - Factory Bronze construction with a maximum of 36" (914.4mm) between the • Water Working Pressure Rating - 175 psi (12 Bars) top of the bottom joist and the bottom of the upper joist. • Maximum low temperature glass bulb rating -67°F (-55° ) HYDRAULIC DESIGN AREA • Materials of Construction, Frame - bronze, Deflector- For all pipe and construction types the design area shall be brass, Screw- brass, Bulb seat- copper, Spring - nickel 1000 ft2 (92.9m2) except for Steel Pipe Systems with insula- alloy, Seal -teflon, Bulb -glass with alcohol based tion filled joists, the design area shall be in accordance with solution, 3mm size the Light Hazard Systems requirements of NFPA 13. SPRINKLER COVERAGE AREA The coverage area of any single GL-SS/IC Sprinkler shall . utilize the SxL rule for all sprinkler spacings (i.e. 16 x 10 = 160 sq. ft. X 0.10 = 16 gpm). NOV 2018 REV. B GFS-600 (Formerly A-40) Page 1 of 6 TABLE A GENERAL INSTALLATION ALLOWANCES STEEL PIPING CPVC PIPING OPEN SPACE HEIGHT TOTAL OPEN SPACE HEIGHT TOTAL COVERAGE DISTANCE CONSTRUCTION TYPE ALLOWED ALLOWED AREA BETWEEN SPACE SPACE Feet2 Meters2 SPRINKLERS MINIMUM MAXIMUM HEIGHT' MINIMUM MAXIMUM HEIGHT' ( ) Feet(Meters) Inches(mm) Inches(mm) Inches(mm) Inches(mm) Inches(mm) Inches(mm) Unobstructed Wood Truss 6(152) 60(1524) 60(1524) 6(152) 60(1524) 60(1524) 1.8 Non-Combustible Bar Joist 6(1.8) 256(78.0) MINIMUM Obstructed Wood Truss 6(152) 60(1524) 84(2134) N/A N/A N/A MAXIMUM 16(4.9) Solid Wood Joist MAXIMUM Insulation Filled Joist 6(152) 60(1524) 72(1829)2 6(152) 60(1524) 72(1829)" NOTE:METRIC CONVERSIONS ARE APPROXIMATE. WHEN TRUSS OR JOIST SPACE IS NONINSULATION FILLED, THE MAXIMUM ALLOWED TOP MEMBER DEPTH IS 12"(305 mm). UP TO 12"(305mm)LOWER MEMBER SPACE. TABLE B SPRINKLER SPECIFICATION AND APPROVALS TEMPERATURE RATING NOMINAL MAX.LOW STYLE SIN K" HAZARD' THREAD SPRINKLER FINISH PRESSURE TEMP.BULB cULus MODEL FACTOR SIZE LENGTH 175°F 200°F RATING RATING (79°C) (93°C) UPRIGHT GL5608 5.6 LH 1/2"NPT 2 1/4" Factory X X 175 psi -67'F X (80 metric) (15mm) (5.7cm) Bronze (12 Bars) (-55°C) NOTE: METRIC CONVERSIONS ARE APPROXIMATE. SPRINKLERS SHALL BE LIMITED AS PER THE REQUIREMENTS OF NFPA13 AND ANY OTHER RELATED DOCUMENTS. OBSTRUCTION CRITERIA For systems where the Globe "IC" Upright Sprinklers are the Globe "IC" Upright Sprinkler must use the obstruction positioned with 15' (4.6m) or less between sprinklers the requirements for extended coverage upright sprinklers. Globe "IC" Upright Sprinkler must use the obstruction re- quirements for standard spray upright sprinklers. NOTE: For systems where the Globe "IC" Upright Sprinklers are WEB MEMBERS AND GUSSETS SHALL NOT BE CONSIDERED OB- STRUCTIONS PROVIDED THE MINIMUM 4-1/2 INCH LATERAL DISTANCE positioned with greater than 15' (4.6m) between sprinklers REQUIRED BY THE SPECIFIC APPLICATION LISTING IS MAINTAINED. CPVC DESIGN REQUIREMENTS SYSTEM TYPE PARTITION REQUIREMENTS The concealed space being protected must be broken up Wet pipe system. into areas no greater than 1000 square feet either by full height walls or by draft curtains. ALLOWABLE CONSTRUCTION TYPES DRAFT CURTAINS • Unobstructed wood truss construction' When draft curtains are used they must be 8" (203.2mm) in height or one third of the depth of the concealed • Unobstructed bar joist construction' space, whichever is greater. Draft curtains must be • Non-combustible insulation filled solid wood joist constructed of a material that will not allow for heat to construction' escape through or above them. • Non-combustible insulation filled composite wood joist construction' NOTE: Upperjoist/truss cannot be more than 4"(101.6mm)in height. 2 The joist space in non-combustible insulation filled joist construction must be completely filled with noncombustible insulation and secured in place by metal wire netting to hold the insulation in place in the event of a fire. NOV 2018 REV. B GFS-600 (Formerly A-40) Page 2 of 6 DEFLECTOR POSITION CPVC PIPE INSTALLATION • 1 1/2 to 4 inches below the upper deck for unobstructed Horizontal runs of CPVC piping must be located with the wood truss and bar joist constructions. Deflector must bottom of the piping not more than 6" (152.4mm) above the be below the bottom of the top chord in trusses or below ceiling below or above ceiling insulation (if present), or one bottom of joist. third depth of the combustible concealed space as mea- - * 1 '/2 to 4 inches below the joists for non-combustible sured between the top surface of the ceiling below to the insulation filled solid and composite wood joist bottom of the floor above or the bottom of the noncombus- constructions. tible insulation above. Whichever is smaller. _ * 4 '/2 inches away from trusses. When the lower joists are greater than 6"(152.4mm) in height, CPVC piping is permitted to be attached directly to CONCEALED SPACE SIZE the top of the joist. The CPVC piping can be used to supply All spaces must have a minimum open space (from top of the Globe "IC" Upright Sprinklers as well as the sprinklers Protecting the space below. lower joist, cord, or truss to bottom of upper joist, cord, or truss) of 6" (152.4mm). (see Figures 1 and 2) When using 1" (DN25) or larger pipe, a hanger must be re- Unobstructed wood truss and bar joist construction must not stralocated at the truss nearest a sprig for purposes of have a total bottom of floor to top of ceiling space height of (304.t. If using /b (D laterally19) piping, all sprigs methodsover 12" more than 60" (1.5m). (see Figure 2) (304.8mm) must be braced using described in the NFPA standards. Where CPVC piping must Joist construction with noncombustible insulation in the be offset to go over an obstruction that will violate the hori- upper deck must not have an open space (from top of lower zontal positioning requirements the CPVC piping must be joist to bottom of upper joist) of greater than 60 inches in spaced not greater than 6 inches from that obstruction and size. They must not have a total concealed space height of an additional Globe IC Upright Sprinkler must be provided greater than 72" (1.8m). This allows for a maximum lower to protect the section of CPVC piping (see Figure 1 and 2). joist space of 12" (304.8mm). CPVC piping must be kept a minimum of 18" (457.2mm) lat- Solid wood joist and obstructed truss construction must erally away from heat sources such as heat pumps, fan mo- not have an open space (from top of lower joist or truss to tors, and heat lamps. bottom of upper joist or truss) of greater than 60"(1.5m) in size. They must not have a total concealed space height of greater than 84"(2.1m). The upper joist space must not be greater than 12"(304.8mm) in depth (see Figure 2) -.--4 1/2"(114mm)MIN. 38mm MIN. TO FACE OF WOOD TRUSS 6"(152mm)MAX.-••• f 1 172" (38mm) OR TOP CHORD OF BAR JOIST FOR CPVC PIPE UPPER DECK 4"(102mm)MAX. DEFLECTOR MUST BE L// /////////////////////////////////////////4j BELOW BOTTOM OF TOP CHORD TOP CHORD 4"(100mm)MAX. FRAME ARMS MUST BE i INSTALLED IN-LINE WITH PIPE RUN �--6 (125mm)MAX. GL560R L FOR CPVC PIPE (MODEL IC SPRINKLER) 11 u,.0 U LI u • 3• •� 0'i C• 6"(152mm)MIN. 12"(305mm)MIN. CI.CI o•CI"CI • 60"(1524mm)MAX. •❑ ❑ ❑I o`! �❑ • OBSTRUCTION • 3•3.1 .11- :1;30.3.iCST+ I . .0 3• .'.0 3C. 0• O-o-o-io-o I - \' = \ \\ OPOF CEILING COR � DP WHEN OFFSETTING CPVC PIPE OVER AN "(152mm)MAX.ABOVE CEILING TO BOTTOM OF PIPE MUST BE INSTALLED DIRECTLY ON THE CPVC SPRINKLER OR NON-COMBUSTIBLE CEILING INSULATION,OR 1/3 OVER THE OBSTRUCTION. THE DEPTH OF CONCEALED SPACE(AS MEASURED FROM TOP SURFACE OF CEILING TO BOTTOM SURFACE OF DECK),OR WHICH EVER IS SMALLER. FIGURE 1 : CPVC PIPE UNOBSTRUCTED WOOD TRUSS AND BAR JOIST CONSTRUCTION NOV 2018 REV. B GFS-600 (Formerly A-40) Page 3 of 6 INSULATION MUST BE HELD ON-COMBUSTIBLE SOLID WOOD JOIST IN PLACE WITH METAL INSULATION COMPOSITE WOOD JOIST 12"(305mm)MAX.DEPTH WIRE NETTING 12"(305rnm)MAX.DEPTH WOOD TRUSS \\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\'`A\\\\\\\\\\\\\\`:Q\\`\\\\\\\\\\\\ UPPER DECK TOP CHORD if /' %;/,r12"(305mm)MAX.DEPTH ��1 1/2"(38mm)MIN4"(102mm)MAXiI /� �j 0 _ A i. ../.10/1P GL5608 •"(152mm)MAX. II n (MODEL IC SPRINKLER) FOR CPVC FRAME ARMS MUST —�_,� •"(152mm)MAX. _ BE INSTALLED I FOR GPVC IN-LINE WITH PIPE RUN I ■ 6"(152mm)MIN. i F OBSTRUCTION 72 60"(1524mm)MAX. (1829mm) MAX. WOOD TRUSS D O D WEB MEMEBER + O yj�0 0-W ,{1� •t CEILING `lfi ORME_1 BOTTOM OF PIPE/ I % MEW II TOP OF CHORD `\\\\\\\\\\\\\\\\\\\\\\\CS"\ \\`\\\\\\\\\\\\\\\\\\\\\\\\\\\\"\\\ WHEN OFFSETTING CPVC PIPE OVER AN OBSTRUCTION,A GL5608 MODEL'IC"SPRINKLER MUST BE INSTALLED DIRECTLY ON THE PIPE OVER THE OBSTRUCTION. 6"(152mm)MAX.ABOVE CEILING OR NON-COMBUSTIBLE CEILING INSULATION.OR 1)3 THE DEPTH OF CONCEALED— AREA(AS MEASURED FROM TOP SURFACE OF CEILING TO TOP SURFACE OF JOIST INSULATION ABOVE),OR WHICH EVER IS SMALLER. WHEN THE LOWER JOIST IS GREATER THAN 6"(152mm)IN HEIGHT CPVC PIPING IS PERMITTED TO BE ATTACHED DIRECTLY TO THE TOP OF THE JOIST. FIGURE 2: CPVC PIPE NON-COMBUSTIBLE INSULATION FILLED UPPER DECK SOLID WOOD, COMPOSITE WOOD JOIST, OR WOOD TRUSS CONSTRUCTION STEEL PIPING DESIGN REQUIREMENTS SYSTEM TYPE DRAFT CURTAINS " Wet pipe system and dry type systems. Draft Curtain for Unobstructed wood truss construction and noncombustible bar joist construction must be 8" (203.2mm) ALLOWABLE CONSTRUCTION in height or one third of the depth of the concealed space, whichever is greater. Draft curtains must be constructed of TYPES a material that will not allow for heat to escape through or • Unobstructed wood truss construction' above them. • Unobstructed bar joist construction' Draft Curtain for Obstructed wood truss and solid wood joist • Solid wood joist construction2 construction must be 6" (152.4mm) in height or one third of the depth of the concealed space, whichever is greater. • Obstructed wood truss construction2Draft curtains must be constructed of a material that will not • Non-combustible insulation filled solid wood joist allow for heat to escape through or above them. construction3 • Non-combustible insulation filled composite wood joist DEFLECTOR POSITION construction3 • 1 1/2 to 4 inches below the upper deck for unobstructed NOTE: wood truss and bar joist constructions. Deflector must Upper joist/truss cannot be more than 4"(101.6mm)in height. be below the bottom of the top chord in trusses or below 2 Upper joist/truss cannot be more than 12"(304.8mm)in height. bottom of joist. 3 The joist space in non-combustible insulation filled joist construction must be • completely filled with noncombustible insulation and secured in place by metal 1 1/2 to 4 inches below the joists for noncombustible wire netting to hold the insulation in place in the event of a fire. insulation filled solid and composite wood joist construction. PARTITION REQUIREMENTS • 1 1/2 to 2 inches below the joist or truss for solid wood For unobstructed wood truss construction, unobstructed joist or obstructed truss construction. bar joist construction, solid wood joist construction, and • 4 '/2 inches away from trusses obstructed wood truss construction the concealed space being protected must be broken up into areas no greater BLOCKING than 1000 square feet either by full height walls or by draft For solid wood joist and obstructed wood truss construction curtains. blocking must be provided in each of the channels between Noncombustible insulation filled joist construction is not re- the upper joists or trusses. The blocking must be located - quired to be broken up into partitioned areas. where the draft curtains intersect the channels. The block- ing must be installed to the full depth of the joists and be installed as to not allow heat to escape through or above the blocking. The blocking must be installed using either the - same material as the joists or a noncombustible material. NOV 2018 REV. B GFS-600 (Formerly A-40) Page 4 of 6 CONCEALED SPACE SIZE All spaces must have a minimum open space (from top of size. They must not have a total concealed space height of lower joist, cord, or truss to bottom of upper joist, cord, or greater than 72"(1.8m). This allows for a maximum lower truss)of 6"(152.4mm) (see Figures 3,4, and 5). joist space of 12"(304.8mm) (see Figure 4). Unobstructed wood truss and bar joist construction must not Solid wood joist and obstructed truss construction must • have a total concealed space height of more than 60"(1.5m). not have an open space (from top of lower joist or truss to (see Figure 3). bottom of upper joist or truss) of greater than 60"(1.5m) in Joist construction with noncombustible insulation in the size. They must not have a total concealed space height of - upper deck must not have an open space (from top of lower greater than 84"(2.1m). The upper joist space must not be joist to bottom of upper joist) of greater than 60"(1.5m) in greater than 12"(304.8mm) in depth(see Figure 4). 4 1/2"(114mm)MIN.Ts UPPER DECK FACE OF WOOD TRUSS OR 1 1/2"(38mm)MIN. TOP CHORD OF BAR JOISTDEFLECTOR MUST BE 4"(100mm)MAX. BELOW BOTTOM OF TOP ��`�`�`�`��`��`�� CHORD TOP CHORD % I e % 4"(100mm)MAX. L5808 ; (MODEL IC SPRINKLER) FRAME ARMS MUST ��r� (1524mm) BE INSTALLED MAX. IN-LINE WITH PIPE RUN 11 6" (15,2mm) MIN. 1 2 % /-% EILING FIGURE 3: STEEL PIPE UNOBSTRUCTED WOOD TRUSS OR NON-COMBUSTIBLE BAR JOIST CONSTRUCTION 2x FLOOR SOLID WOOD JOISTS/OBSTRUCTED TRUSS UPPER DECK 16"(406mm)ON CENTER -1--- i 1 12"(3005mm) MAX / 1 1/2"(38mm)MIN. r 2"(51mm)MAX. L5608 FRAME ARMS MUST (MODEL IC SPRINKLER) 1 84" BE INSTALLED I (2134mm) IN-LINE WITH PIPE RUN : -Y- MAX. I I 6"(152mm)MIN. EILING 60"(1524mm) MAX. FRAMING MINIM % i CEILING FIGURE 4: STEEL PIPE OBSTRUCTED WOOD TRUSS OR SOLID WOOD JOIST CONSTRUCTION NOV 2018 REV. B GFS-600 (Formerly A-40) Page 5 of 6 UPPER DECK NON-COMBUSTIBLE 2x FLOOR SOLID INSULATION COMPOSITE WOOD JOIST WOOD JOIST Itt✓irrlltltl Ht:71111f11r11rr,,,lf1 irli AY4n SIrtt 11 tVoii 7 u�%uuuuuu/luuu��u�/,�uu�uuu��'�.u��u��ur, ul wi��rlrlrlrlrlt�r�rlrlti 1�rlt�rlrlrlt�tlr� erlld ItIrIrltltnrltlrltI,IIem erltltlw%11111 11/2°(38mm)MIN. - 111�/rrr/r1/t/H1t//tlttttt/ttt /ttt ttltfttl PI t11111M11) 'ft F 4"(102mm)MAX. u. a,uu�uu�,. I,,,,,u,1,1,,,u%111u11uu141.w8uu,111,014” EERErtl.rtt.tr:VLrrrr.tr,,11111/tr.reJ./J.t.G./,J..11111/.rrr.Nhoh,* INSULATION MUST BE HELD L5608 IN PLACE WITH METAL _ (MODEL IC SPRINKLER) _ WIRE NETTING N. r i 6"(152mm)MIN. " IN ill-Y- 60"(1524mm)MAX. FRAME ARMS MUST BE INSTALLED I 72" IN-LINE WITH PIPE RUN (1629mm) MAX. -Y-1, CEILING FRAMING 1 .\\\\`\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\\C\\\\\\ CEILING FIGURE 5: STEEL PIPE NON-COMBUSTIBLE INSULATION FILLED UPPER DECK SOLID WOOD OR COMPOSITE WOOD JOIST CONSTRUCTION ORDERING INFORMATION GLOBE® PRODUCT Quantity • SIN • Style • Orifice *Thread Size WARRANTY Temperature • Finishes • Desired Quantity Globe agrees to repair or replace any of its own manu- factured products found to be defective in material or work- Wrench - P/N 325390 manship for a period of one year from date of shipment. For specific details of our warranty please refer to Price List Terms and Conditions of Sale (Our Price List). 4077 Airpark Dr. Technical Support Standish, MI 48658 1-800-248-0278 www.globesprinkler.com ,.• . Ph. 989-846-4583 techservice@globesprinkler.com :' 111.4 NOV 2018 REV. B GFS-600 (Formerly A-40) Page 6 of 6 r BE`1J1/ 4077 Airpark Dr. Standish, MI 48658•989-846-4583•www.globesprinkler.com FIRE SPRINKLER CORPORATION Technical Support•989-414-2600•techservice@globesprinkler.com SPECIFIC APPLICATION MODEL "IC" INTERSTITIAL COMBUSTIBLE CONCEALED SPACE UPRIGHT SPRINKLER GL5608 RECEIVED GENERAL DESCRIPTION JAN 7 2020 The Globe Series GL-SS/IC GL5608 Interstitial Combustible Space Sprinkler is a quick response, upright, specific appli- CITY OF TIGARD cation sprinkler designed to provide protection of light haz- "T 3UILDING DIVISION and combustible and non-combustible concealed spaces, inclusive of interstitial (between floors) or attic spaces (with slopes 2:12 or less). Each GL5608 sprinkler can be de- signed for up to 16ft x 16ft (4.9m x 4.9m) spacing, providing as much as 256 ft2 (23.8m2)of protection per sprinkler. The GL5608 sprinkler meets the requirements of Under- writers Laboratories UL 199H to comply with criteria for the protection of combustible concealed spaces as described in 740- NFPA 13. ' ° When heat is absorbed, liquid within the glass bulb ex- pands, increasing the internal pressure. At the prescribed temperature the internal pressure within the ampule ex- -ceeds the strength of the glass causing the glass to shatter. GL 5608 -This results in water discharge which is distributed in an ap- proved V .!V pattern. APPLICATION SERIES GL-SS/IC UPRIGHT The GL-SS/IC GL5608 can be designed for installation in SPRINKLER: CPVC wet pipe sprinkler systems and steel wet pipe or dry pipe sprinkler systems. The GL5608 can be used in The Globe GL-SS/IC GL5608 Interstitial Combustible Up- concealed spaces having roof pitch of 2 in 12 or less con- right Sprinkler has been Listed to be used beyond the 36" structed of wood truss, non-combustible bar joist, solid (914.4mm) height to a height of 60" (1.5m) to provide more wood joists, or composite wood joists. The specific design functionality in installation specifically in areas where the requirements for each type of piping system, and construc- height of the concealed space is both above and below the tion materials can be found in the following sections of this height of 36" (914.4mm). document. NFPA 13 REQUIREMENTS TECHNICAL DATA • cULus Listed for coverage areas up to 256 ft2 (23.8 m2) Sprinklers shall be Listed for use in combustible concealed • 16 ft(4.9 m) maximum and 6 ft (1.8 m) minimum spaces (with a slope not exceeding 2 in 12) with combus- Sprinkler Spacing tible wood truss, wood joist construction, or bar joist con- • Maximum Open Space Height 60 in (1.5 m) struction having a combustible upper surface and where the • Temperature Ratings- 175°F (79°C), 200°F (93°C) depth of the space is less than 36" (914.4mm) from deck to deck or with double wood joist and composite wood joist Finish• Factory Bronze construction with a maximum of 36" (914.4mm) between the • Water Working Pressure Rating - 175 psi (12 Bars) top of the bottom joist and the bottom of the upper joist. • Maximum low temperature glass bulb rating -67°F (-55°C) HYDRAULIC DESIGN AREA • Materials of Construction, Frame - bronze, Deflector- For all pipe and construction types the design area shall be brass, Screw- brass, Bulb seat- copper, Spring - nickel 1000 ft2 (92.9m2)except for Steel Pipe Systems with insula- alloy, Seal -teflon, Bulb -glass with alcohol based tion filled joists, the design area shall be in accordance with solution, 3mm size the Light Hazard Systems requirements of NFPA 13. SPRINKLER COVERAGE AREA The coverage area of any single GL-SS/IC Sprinkler shall utilize the SxL rule for all sprinkler spacings (i.e. 16 x 10 = 160 sq. ft. X 0.10 = 16 gpm). NOV 2018 REV. B GFS-600 (Formerly A-40) Page 1 of 6 r. TABLE A GENERAL INSTALLATION ALLOWANCES STEEL PIPING CPVC PIPING OPEN SPACE HEIGHT TOTAL OPEN SPACE HEIGHT TOTAL COVERAGE DISTANCE CONSTRUCTION TYPE ALLOWED ALLOWED AREA BETWEEN MINIMUM MAXIMUM SPACE MINIMUM MAXIMUM SPACE Feet2(Meters2) SPRINKLERS Inches(mm) Inches(mm) HEIGHT' Inches(mm) Inches(mm) HEIGHT' Feet(Meters) Inches(mm) Inches(mm) Unobstructed Wood Truss • 6(152) 60(1524) 60(1524) 6(152) 60(1524) 60(1524) Non-Combustible Bar Joist 6(1.8) Obstructed Wood Truss 256(78.0) MINIMUM • 6(152) 60(1524) 84(2134) N/A N/A N/A MAXIMUM 16(4.9) Solid Wood Joist MAXIMUM Insulation Filled Joist 6(152) 60(1524) 72(1829)2 6(152) 60(1524) 72(1829)" NOTE:METRIC CONVERSIONS ARE APPROXIMATE. WHEN TRUSS OR JOIST SPACE IS NONINSULATION FILLED, THE MAXIMUM ALLOWED TOP MEMBER DEPTH IS 12"(305 mm). 2 UP TO 12"(305mm)LOWER MEMBER SPACE. TABLE B SPRINKLER SPECIFICATION AND APPROVALS TEMPERATURE RATING NOMINAL MAX.LOW SINTHREAD SPRINKLER PRESSURE STYLE MODEL K" HAZARD' SIZE LENGTH FINISH ° RATING TEMP.BULB cULus FACTOR 175 F 200°F RATING (79°C) (93°C) UPRIGHT GL5608 5.6 LH 1/2"NPT 2 1/4" Factory x X 175 psi -67°F X (80 metric) (15mm) (5.7cm) Bronze (12 Bars) (-55°C) NOTE: METRIC CONVERSIONS ARE APPROXIMATE. 2 SPRINKLERS SHALL BE LIMITED AS PER THE REQUIREMENTS OF NFPA13 AND ANY OTHER RELATED DOCUMENTS. OBSTRUCTION CRITERIA For systems where the Globe "IC" Upright Sprinklers are the Globe "IC" Upright Sprinkler must use the obstruction positioned with 15' (4.6m) or less between sprinklers the requirements for extended coverage upright sprinklers. Globe "IC" Upright Sprinkler must use the obstruction re- quirements for standard spray upright sprinklers. NOTE: For where the Globe "IC" Upright Sprinklers are WEB MEMBERS AND GUSSETS SHALL NOT BE CONSIDERED O8- Fpor systemsed greater than (4.6m)C" beteen sprinklers STRUCTIONS PROVIDED THE MINIMUM 4-1/2 INCH LATERAL DISTANCE REQUIRED BY THE SPECIFIC APPLICATION LISTING IS MAINTAINED. CPVC DESIGN REQUIREMENTS SYSTEM TYPE PARTITION REQUIREMENTS The concealed space being protected must be broken up Wet pipe system. into areas no greater than 1000 square feet either by full height walls or by draft curtains. ALLOWABLE CONSTRUCTION DRAFT CURTAINS TYPES When draft curtains are used they must be 8" (203.2mm) • Unobstructed wood truss construction in height or one third of the depth of the concealed • Unobstructed bar joist construction' space, whichever is greater. Draft curtains must be • Non-combustible insulation filled solid wood joist constructed of a material that will not allow for heat to construction2 escape through or above them. • Non-combustible insulation filled composite wood joist construction2 NOTE: Upper joist/truss cannot be more than 4"(101.6mm)in height. 2 The joist space in non-combustible insulation filled joist construction must be completely filled with noncombustible insulation and secured in place by metal wire netting to hold the insulation in place in the event of a fire. NOV 2018 REV. B GFS-600 (Formerly A-40) Page 2 of 6 r A, DEFLECTOR POSITION CPVC PIPE INSTALLATION • 1 1/2 to 4 inches below the upper deck for unobstructed Horizontal runs of CPVC piping must be located with the wood truss and bar joist constructions. Deflector must bottom of the piping not more than 6" (152.4mm) above the be below the bottom of the top chord in trusses or below ceiling below or above ceiling insulation (if present), or one bottom of joist. third depth of the combustible concealed space as mea- • 1 1/2 to 4 inches below the joists for non-combustible sured between the top surface of the ceiling below to the insulation filled solid and composite wood joist bottom of the floor above or the bottom of the noncombus- constructions. tible insulation above. Whichever is smaller. • 41/2 inches away from trusses. When the lower joists are greater than 6"(152.4mm) in ' height, CPVC piping is permitted to be attached directly to CONCEALED SPACE SIZE the top of the joist. The CPVC piping can be used to supply All spaces must have a minimum open space (from top of the Globe "IC" Upright Sprinklers as well as the sprinklers lower joist, cord, or truss to bottom of upper joist, cord, or protecting the space below. truss)of 6" (152.4mm). (see Figures 1 and 2) When using 1" (DN25) or larger pipe, a hanger must be Unobstructed wood truss and bar joist construction must not located at the truss nearest a sprig for purposes of re- have a total bottom of floor to top of ceiling space height of (304.t. If using /" (DN19) piping, all sprigs over 12" more than 60" (1.5m). (see Figure 2) (304.8mm) must be laterally braced using methods described in the NFPA standards. Where CPVC piping must Joist construction with noncombustible insulation in the be offset to go over an obstruction that will violate the hori- upper deck must not have an open space (from top of lower zontal positioning requirements the CPVC piping must be joist to bottom of upper joist) of greater than 60 inches in spaced not greater than 6 inches from that obstruction and size. They must not have a total concealed space height of an additional Globe IC Upright Sprinkler must be provided greater than 72" (1.8m). This allows for a maximum lower to protect the section of CPVC piping (see Figure 1 and 2). joist space of 12" (304.8mm). CPVC piping must be kept a minimum of 18" (457.2mm) lat- Solid wood joist and obstructed truss construction must erally away from heat sources such as heat pumps, fan mo- not have an open space (from top of lower joist or truss to tors, and heat lamps. bottom of upper joist or truss) of greater than 60"(1.5m) in size. They must not have a total concealed space height of greater than 84"(2.1m). The upper joist space must not be greater than 12"(304.8mm) in depth (see Figure 2) • �4 1/2"(114mm)MIN. 1 1/2"(38mm)MIN. TO FACE OF WOOD TRUSS 6"(152mm)MAX-.- •�- 4" (38 m)MAX. OR TOP CHORD OF BAR JOIST FOR CPVC PIPE UPPER DECK DEFLECTOR MUST AE V/ ///77777777/777/77 W /////////////,//'ate////!/97 I BELOW BOTTOM OF TOP CHORD TOP CHORD 4"(100mm)MAX. FRNSTALLAME AED IRMS N-MUST LINE BE S - - I WITH PIPE RUN GL5608 "(125mm)MAX. FOR CPVC PIPE (MODEL IC SPRINKLER) .u.0 u u u,n.I, �["� ��V } 6'(152mm)MIN. 12"(305mm)MIN. 0 00 0 o,�'`�C 60"(1524mm)MAX. 3 C/73 C- C3LV S V C jCI DO�^��p O�C OBSTRUCTION )0C.l3(D`1 ro.,309% D D D D. C �•6 re -D-o-D9 DSD:` ``\ \� I \\ \• \\��JJJJ \\\\ r EILING `TOP OF CORD7 ii ii ii ii .iiI l/>l////j/ WHEN OFFSETTING CPVC PIPE OVER AN "(152mm)MAX.ABOVE CEILING TO BOTTOM OF PIPE OBSTRUCTION A GL5608 MODEL"IC"SPRINKLER OR NON-COMBUSTIBLE CEILING INSULATION,OR 1/3 MUST BE INSTALLED DIRECTLY ON THE CPVC OVER THE OBSTRUCTION. THE DEPTH OF CONCEALED SPACE(AS MEASURED FROM TOP SURFACE OF CEILING TO BOTTOM SURFACE OF DECK),OR WHICH EVER IS SMALLER. FIGURE 1 : CPVC PIPE UNOBSTRUCTED WOOD TRUSS AND BAR JOIST CONSTRUCTION NOV 2018 REV. B GFS-600 (Formerly A-40) Page 3 of 6 INSULATION MUST BE HELD ON-COMBUSTIBLEI SOLID WOOD JOIST IN PLACE WITH METAL NSULATION COMPOSITE WOOD JOIST 12"(305mm)MAX.DEPTH WIRE NETTING 12"(305mm)MAX.DEPTH WOOD TRUSS %��%4707A®A� � ®��, AAAA ' ��VA UPPER DECK i 12"(305mm)MAX.DEPTH ; `ftt �" 1 1/2"(38mm) „4,4 MIN. ) 5' 41 4"(102mm "1v)MAX. � � 4 / '`11',"•"' GL5608 ”(152mm)MAX. (MODEL IC SPRINKLER) FOR CPVC FRAME ARMS MUST "(152mm)MAX. BE INSTALLED FOR CPVC IN-LINE WITH PIPE RUN 6"(152mm)MIN. OBSTRUCTION 1829mm 60"(1524mm)MAX. ( ) MAX. WOOD TRUSS WEB MEMEBER CEILING BOTTOM OF PIPE/J a° a TOP OF CHORD WHEN OFFSETTING CPVC PIPE OVER AN OBSTRUCTION,A GL5608 MODEL'IC"SPRINKLER MUST BE INSTALLED DIRECTLY ON THE PIPE OVER THE OBSTRUCTION. 6"(152mm)MAX.ABOVE CEILING OR NON-COMBUSTIBLE CEILING INSULATION.OR 1/3 THE DEPTH OF CONCEALED- AREA(AS MEASURED FROM TOP SURFACE OF CEILING TO TOP SURFACE OF JOIST INSULATION ABOVE),OR WHICH EVER IS SMALLER. WHEN THE LOWER JOIST IS GREATER THAN 6"(152mm)IN HEIGHT CPVC PIPING IS PERMITTED TO BE ATTACHED DIRECTLY TO THE TOP OF THE JOIST. FIGURE 2: CPVC PIPE NON-COMBUSTIBLE INSULATION FILLED UPPER DECK SOLID WOOD, COMPOSITE WOOD JOIST, OR WOOD TRUSS CONSTRUCTION STEEL PIPING DESIGN REQUIREMENTS SYSTEM TYPE DRAFT CURTAINS Wet pipe system and dry type systems. Draft Curtain for Unobstructed wood truss construction and noncombustible bar joist construction must be 8" (203.2mm) ALLOWABLE CONSTRUCTION in height or. one third of the depth of the concealed space, whichever is greater. Draft curtains must be constructed of TYPES a material that will not allow for heat to escape through or • Unobstructed wood truss construction' above them. • Unobstructed bar joist construction' Draft Curtain for Obstructed wood truss and solid wood joist • Solid wood joist construction2 construction must be 6" (152.4mm) in height or one third • Obstructed wood truss construction2 of the depth of the concealed space, whichever is greater. Draft curtains must be constructed of a material that will not • Non-combustible insulation filled solid wood joist allow for heat to escape through or above them. construction3 • Non-combustible insulation filled composite wood joist DEFLECTOR POSITION construction3 • 1 1/2 to 4 inches below the upper deck for unobstructed NOTE: wood truss and bar joist constructions. Deflector must Upper joist/truss cannot be more than 4"(101.6mm)in height. be below the bottom of the top chord in trusses or below 2 Upper joist/truss cannot be more than 12"(304.8mm)in height. bottom of joist. 3 The joist space in non-combustible insulation filled joist construction must be completely filled with noncombustible insulation and secured in place by metal • 1 1/2 to 4 inches below the joists for noncombustible wire netting to hold the insulation in place in the event of a fire. insulation filled solid and composite wood joist construction. PARTITION REQUIREMENTS • 1 1/2 to 2 inches below the joist or truss for solid wood For unobstructed wood truss construction, unobstructed joist or obstructed truss construction. bar joist construction, solid wood joist construction, and • 4 '/2 inches away from trusses obstructed wood truss construction the concealed space being protected must be broken up into areas no greater BLOCKING than 1000 square feet either by full height walls or by draft For solid woodjoist and obstructed wood truss construction curtains. blocking must be provided in each of the channels between Noncombustible insulation filled joist construction is not re- the upper joists or trusses. The blocking must be located _ quired to be broken up into partitioned areas. where the draft curtains intersect the channels. The block- ing must be installed to the full depth of the joists and be installed as to not allow heat to escape through or above the blocking. The blocking must be installed using either the - same material as the joists or a noncombustible material. NOV 2018 REV. B GFS-600 (Formerly A-40) Page 4 of 6 CONCEALED SPACE SIZE All spaces must have a minimum open space (from top of size. They must not have a total concealed space height of lower joist, cord, or truss to bottom of upper joist, cord, or greater than 72"(1.8m). This allows for a maximum lower truss) of 6"(152.4mm) (see Figures 3, 4, and 5). joist space of 12"(304.8mm) (see Figure 4). Unobstructed wood truss and bar joist construction must not Solid wood joist and obstructed truss construction must . have a total concealed space height of more than 60"(1.5m). not have an open space (from top of lower joist or truss to (see Figure 3). bottom of upper joist or truss) of greater than 60"(1.5m) in Joist construction with noncombustible insulation in the size. They must not have a total concealed space height of . upper deck must not have an open space (from top of lower greater than 84''(2.1m). The upper joist space must not be joist to bottom of upper joist) of greater than 60"(1.5m) in greater than 12"(304.8mm) in depth(see Figure 4). 4 1,2"(114mm)MIN.TO UPPER DECK FACE OF WOOD TRUSS OR TOP CHORD OF BAR JOIST 1 1/2"(38mm)MIN. DEFLECTOR MUST BE 4"(100mm)MAX. BELOW BOTTOM OF TOP alh. `MN& IN CHORD HORD 9 4"(100mof TOP C MAX / 4 g _ a i .." 1' GL5608 ' - (MODEL IC SPRINKLER) IIK ' FRAME ARMS MUST - ��r� (1524mm) BE INSTALLED MAX. IN-LINE WITH PIPE RUN 6" 052.)MIN. III / i 4 CEILING iiimmommoimmiiiimmoi FIGURE 3: STEEL PIPE UNOBSTRUCTED WOOD TRUSS OR NON-COMBUSTIBLE BAR JOIST CONSTRUCTION 2x FOR SOLLOID WOOD JOISTS/OBSTRUCTED TRUSS UPPER DECK 16"(406mm)ON CENTER P 12"(305— Q MAX. % 1 1/2"(3Bmm)MIN.i % mm) 1 2"(51 mm)MAX. L5608 FRAME ARMS MUST -- (MODEL IC SPRINKLER) . 84" BE INSTALLED t (2134mm) IN-LINE WITH PIPE RUN III MAX. I I 6"(152mm)MIN. 60"(1524mm)MAX. FILING —Y-J FRAMING :AQAAAAAxVVAVVVVVVV\VAAAAAVAVVVVVVxxxxAVAAAAC\VAVVV.,,xx xxxx, CEILING FIGURE 4: STEEL PIPE OBSTRUCTED WOOD TRUSS OR SOLID WOOD JOIST CONSTRUCTION NOV 2018 REV. B GFS-600 (Formerly A-40) Page 5 of 6 UPPER DECK NON-COMBUSTIBLE 2x FLOOR SOLID INSULATION COMPOSITE WOOD JOIST WOOD JOIST VNANANNANANAN.ANNN................................. W1'%iLtitititAtdiIY:PEIArddlbr:49 atiritu 'ddirAriri6r0 :1 Wiririt elt/tltltltititltl/rlMitMItM P/WiWIWAYMAYMMln�rlti r1 1/2"(38mm)MIN. ht.w Inflttitltit/t/tlt r tntrrtttIt/t,IItit/r/tit/rir/rlt/111,r/t/r/rlrlt/rlr/r/r/r1t1171rIt/r/ F 4"(102mm)MAX. • r.r.rrr.t.rtttta/,.........../r.r.rrr.�.trcrr.J��.rtrrrrrrr:/:.r INSULATION MUST BE HELD L5608 IN PLACE WITH METAL _ (MODEL IC SPRINKLER) WIRE NETTING t 6"(152mm)MIN. • ill-Y- 60"(1524mm)MAX. FRAME ARMS MUST BE INSTALLED 72" IN-LINE WITH PIPE RUN ' (1829mm) MAX. CEILING FRAMING /- VNA$ `.A A A A AANANA A A A A A A'NANSCVANAVONANANANAANNSNA FILING FIGURE 5: STEEL PIPE NON-COMBUSTIBLE INSULATION FILLED UPPER DECK SOLID WOOD OR COMPOSITE WOOD JOIST CONSTRUCTION ORDERING INFORMATION GLOBE® PRODUCT Quantity • SIN • Style • Orifice •Thread Size WARRANTY Temperature • Finishes • Desired Quantity Globe agrees to repair or replace any of its own manu- factured products found to be defective in material or work- Wrench - P/N 325390 manship for a period of one year from date of shipment. For specific details of our warranty please refer to Price List Terms and Conditions of Sale (Our Price List). 4077 Airpark Dr. Technical Support Standish, MI 48658 1-800-248-0278 www.globesprinkler.com 41 Ph. 989-846-4583 techservice@globesprinkler.com NOV 2018 REV. B GFS-600 (Formerly A-40) Page 6 of 6 t t 7.71;„ BE 4077 Airpark Dr. Standish, MI 48658•989-846-4583•www.globespnnkier.com FIRE SPRINKLER CORPORATION Technical Support•989-414-2600•techservice@globesprinkler.com SPECIFIC APPLICATION MODEL "IC" INTERSTITIAL COMBUSTIBLE CONCEALED SPACE UPRIGHT SPRINKLER GL5608 GENERAL DESCRIPTION The Globe Series GL-SS/IC GL5608 Interstitial Combustible Space Sprinkler is a quick response, upright, specific appli- cation sprinkler designed to provide protection of light haz- ard az and combustible and non-combustible concealed spaces, inclusive of interstitial (between floors) or attic spaces (with slopes 2:12 or less). Each GL5608 sprinkler can be de- signed for up to 16ft x 16ft (4.9m x 4.9m) spacing, providing as much as 256 ft2 (23.8m2)of protection per sprinkler. The GL5608 sprinkler meets the requirements of Under- •11 writers Laboratories UL 199H to comply with criteria for the - e. protection of combustible concealed spaces as described in NFPA 13. When heat is absorbed, liquid within the glass bulb ex- pands, increasing the internal pressure. At the prescribed temperature the internal pressure within the ampule ex- ceeds the strength of the glass causing the glass to shatter. GL Cc08 This results in water discharge which is distributed in an ap- proved V .!V pattern. APPLICATION SERIES GL-SS/IC UPRIGHT The GL-SS/IC GL5608 can be designed for installation in SPRINKLER: CPVC wet pipe sprinkler systems and steel wet pipe or dry pipe sprinkler systems. The GL5608 can be used in The Globe GL-SS/IC GL5608 Interstitial Combustible Up- concealed spaces having roof pitch of 2 in 12 or less con- right Sprinkler has been Listed to be used beyond the 36" structed of wood truss, non-combustible bar joist, solid (914.4mm) height to a height of 60" (1.5m) to provide more wood joists, or composite wood joists. The specific design functionality in installation specifically in areas where the requirements for each type of piping system, and construc- height of the concealed space is both above and below the tion materials can be found in the following sections of this height of 36" (914.4mm). document. TECHNICAL DATA NFPA 13 REQUIREMENTS • cULus Listed for coverage areas up to 256 ft2 (23.8 m2) Sprinklers shall be Listed for use in combustible concealed • 16 ft (4.9 m) maximum and 6 ft (1.8 m) minimum spaces (with a slope not exceeding 2 in 12) with combus- Sprinkler Spacing tible wood truss, wood joist construction, or bar joist con- • Maximum Open Space Height 60 in (1.5 m) struction having a combustible upper surface and where the • Temperature Ratings- 175°F (79°C), 200°F (93°C) depth of the space is less than 36" (914.4mm) from deck to deck or with double wood joist and composite wood joist • Finish - Factory Bronze construction with a maximum of 36" (914.4mm) between the • Water Working Pressure Rating - 175 psi (12 Bars) top of the bottom joist and the bottom of the upper joist. • Maximum low temperature glass bulb rating -67°F (-55°C) HYDRAULIC DESIGN AREA • Materials of Construction, Frame- bronze, Deflector- For all pipe and construction types the design area shall be brass, Screw- brass, Bulb seat- copper, Spring - nickel 1000 ft2 (92.9m2) except for Steel Pipe Systems with insula- alloy, Seal -teflon, Bulb - glass with alcohol based tion filled joists, the design area shall be in accordance with solution, 3mm size the Light Hazard Systems requirements of NFPA 13. SPRINKLER COVERAGE • AREA The coverage area of any single GL-SS/IC Sprinkler shall utilize the SxL rule for all sprinkler spacings (i.e. 16 x 10 = 160 sq. ft. X 0.10 = 16 gpm). NOV 2018 REV. B GFS-600 (Formerly A-40) Page 1 of 6 t t TABLE A GENERAL INSTALLATION ALLOWANCES STEEL PIPING CPVC PIPING OPEN SPACE HEIGHT TOTAL OPEN SPACE HEIGHT TOTAL COVERAGE DISTANCE CONSTRUCTION TYPE ALLOWED ' ALLOWED AREA BETWEEN MINIMUM MAXIMUM SPACE MINIMUM MAXIMUM SPACE Fee(Meters2) SPRINKLERS Inches(mm) Inches(mm) HEIGHT' Inches(mm) Inches(mm) HEIGHT' Feet(Meters) Inches(mm) Inches(mm) Unobstructed Wood Truss 6(152) 60(1524) 60(1524) 6(152) 60(1524) 60(1524) 6(1.8) Non-Combustible Bar Joist 256(78.0) MINIMUM Obstructed Wood Truss 6(152) 60(1524) 84(2134) N/A N/A N/A MAXIMUM 16(4.9) Solid Wood Joist MAXIMUM Insulation Filled Joist 6(152) 60(1524) 72(1829)2 6(152) 60(1524) 72(1829)" NOTE:METRIC CONVERSIONS ARE APPROXIMATE. WHEN TRUSS OR JOIST SPACE IS NONINSULATION FILLED. THE MAXIMUM ALLOWED TOP MEMBER DEPTH IS 12"(305 mm). UP TO 12"(305mm)LOWER MEMBER SPACE. TABLE B SPRINKLER SPECIFICATION AND APPROVALS TEMPERATURE RATING NOMINAL MAX.LOW SIN THREAD SPRINKLER PRESSURE STYLE MODEL "K" HAZARD' SIZE LENGTH FINISH ° ° RATING TEMP. BULB cULus FACTOR 175 F 200 F RATING (79°C) (93°C) UPRIGHT GL5608 5.6 LH 1/2"NPT 2 1/4° Factory X X 175 psi -67°F X (80 metric) (15mm) (5.7cm) Bronze (12 Bars) (-55°C) NOTE: METRIC CONVERSIONS ARE APPROXIMATE. 2 SPRINKLERS SHALL BE LIMITED AS PER THE REQUIREMENTS OF NFPA13 AND ANY OTHER RELATED DOCUMENTS. OBSTRUCTION CRITERIA For systems where the Globe "IC" Upright Sprinklers are the Globe "IC" Upright Sprinkler must use the obstruction positioned with 15' (4.6m) or less between sprinklers the requirements for extended coverage upright sprinklers. Globe "IC" Upright Sprinkler must use the obstruction re- quirements for standard spray upright sprinklers. NOTE: OB- For where the Globe "IC" Upright Sprinklers are WEB MEMBERS AND GUSSETS SHALL NOT BE CONSIDERED Fosystemsed greater than C"(4.6m) between sprinklersae STRUCTIONSPROVIDEDTHEMINIMUM4-1/2INCHLATERALDISTANCE REQUIRED BY THE SPECIFIC APPLICATION LISTING IS MAINTAINED. CPVC DESIGN REQUIREMENTS SYSTEM TYPE PARTITION REQUIREMENTS The concealed space being protected must be broken up Wet pipe system. into areas no greater than 1000 square feet either by full height walls or by draft curtains. ALLOWABLE CONSTRUCTION TYPES DRAFT CURTAINS • Unobstructed wood truss construction' When draft curtains are used they must be 8" (203.2mm) in height or one third of the depth of the concealed • Unobstructed bar joist construction' space, whichever is greater. Draft curtains must be • Non-combustible insulation filled solid wood joist constructed of a material that will not allow for heat to construction2 escape through or above them. • Non-combustible insulation filled composite wood joist construction2 NOTE: Upper joist/truss cannot be more than 4"(101.6mm)in height. 2 The joist space in non-combustible insulation filled joist construction must be completely filled with noncombustible insulation and secured in place by metal wire netting to hold the insulation in place in the event of a fire. NOV 2018 REV. B GFS-600 (Formerly A-40) Page 2 of 6 DEFLECTOR POSITION CPVC PIPE INSTALLATION • 1 1/2 to 4 inches below the upper deck for unobstructed Horizontal runs of CPVC piping must be located with the wood truss and bar joist constructions. Deflector must bottom of the piping not more than 6" (152.4mm) above the be below the bottom of the top chord in trusses or below ceiling below or above ceiling insulation (if present), or one bottom of joist. third depth of the combustible concealed space as mea- • 1 1/2 to 4 inches below the joists for non-combustible sured between the top surface of the ceiling below to the insulation filled solid and composite wood joist bottom of the floor above or the bottom of the noncombus- constructions. tible insulation above. Whichever is smaller. • 4 1/2 inches away from trusses. When the lower joists are greater than 6"(152.4mm) in height, CPVC piping is permitted to be attached directly to CONCEALED SPACE SIZE the top of the joist. The CPVC piping can be used to supply All spaces must have a minimum open space (from top of the Globe "IC" Upright Sprinklers as well as the sprinklers lower joist, cord, or truss to bottom of upper joist, cord, or protecting the space below. truss) of 6" (152.4mm). (see Figures 1 and 2) When using 1" (DN25) or larger pipe, a hanger must be Unobstructed wood truss and bar joist construction must not located at the truss nearest a sprig for purposes of re- have a total bottom of floor to top of ceiling space height of must be laterally bt. If using /" (DN19) piping,raaced using methods all sprigs over 12" more than 60" (1.5m). (see Figure 2) (304.8mm) described in the NFPA standards. Where CPVC piping must Joist construction with noncombustible insulation in the be offset to go over an obstruction that will violate the hori- upper deck must not have an open space (from top of lower zontal positioning requirements the CPVC piping must be joist to bottom of upper joist) of greater than 60 inches in spaced not greater than 6 inches from that obstruction and size. They must not have a total concealed space height of an additional Globe IC Upright Sprinkler must be provided greater than 72" (1.8m). This allows for a maximum lower to protect the section of CPVC piping (see Figure 1 and 2). joist space of 12" (304.8mm). CPVC piping must be kept a minimum of 18" (457.2mm) lat- Solid wood joist and obstructed truss construction must erally away from heat sources such as heat pumps, fan mo- not have an open space (from top of lower joist or truss to tors, and heat lamps. bottom of upper joist or truss) of greater than 60"(1.5m) in size. They must not have a total concealed space height of greater than 84"(2.1m). The upper joist space must not be greater than 12"(304.8mm) in depth (see Figure 2) �4 1/2"(114mm)MIN. 1 1/2"(38mm)MIN. TO FACE OF WOOD TRUSS 6"(152mm)MAX.—.- -� UPPER DECK OR TOP CHORD OF BAR JOIST FOR CPVC PIPE 4"(102mm)MAX. DEFLECTOR BOTTOMT \ ///////////////,z '///, BELOW TOP CHORD TOP CHORDS`\\ 4"(100mm)MAX. FRAME ARMS MUST BE INSTALLED IN-LINE WITH PIPE RUN �-6 (125mm)MAX. (MODEL IC SPRINKLER) u [I 1 FOR CPVC PIPE LLJJ u_u_ut,u_u_= 1 �[�57[�[ac 6"(152mm)MIN. 12"(305mm)MIN. _o_o_o,.o�o-c 60"(1524mm)MAX. 3c 3c o'o 0 0 ❑_[ OBSTRUCTION DCEJC t;a)K ,7 -0:0-0"0 O_C 30 3C 30C 3C ipm =°- - -„°,- - • - \� CEILING `TOP OFM OF CORD PIPE/ i/./. ��7�� I //7l-////7ii// //��///i// l>/1 WHEN OFFSETTING CPVC PIPE OVER AN ”(152mm)MAX.ABOVE CEILING TO BOTTOM OF PIPE OBSTRUCTION, BE INSTAL ED D RECTTLY ON THE CPVC ER OR NON-COMBUSTIBLE CEILING INSULATION,OR 1/3 OVER THE OBSTRUCTION. THE DEPTH OF CONCEALED SPACE(AS MEASURED FROM TOP SURFACE OF CEILING TO BOTTOM SURFACE OF DECK),OR WHICH EVER IS SMALLER. FIGURE 1: CPVC PIPE UNOBSTRUCTED WOOD TRUSS AND BAR JOIST CONSTRUCTION NOV 2018 REV. B GFS-600 (Formerly A-40) Page 3 of 6 INSULATION MUST BE HELD O IN COMBUSTIBLE SOLID WOOD JOIST IN PLACE WITH METAL NSULATION COMPOSITE WOOD JOIST 12"(305mm)MAX.DEPTH WIRE NETTING 12"(305mm)MAX.DEPTH WOOD TRUSS \\\\\\\\\\\\\\\\\\\\�\\\\\\\\\\\\\N:\`\\\\\\\\\\\\\�:Q�\\\\\\\\\\\\\\ UPPER DECK TOP CHORD /1111111 %/�,� v�i12"(305mm)MAX.DEPTH 1 12"(38mm)MIN. ��4"(102mm)MAX. / i,, viii GL5608 (152mm)MAX. (MODEL IC SPRINKLER) AFOR CPVC FRAME ARMS MUST r-Y_,� •"R CPVC)MAX. B5 INSTALLED FOR CPVC IN-UNE WITH PIPE RUNIII 6"(152mm)MIN. ST . J OBSTRUCTION 72 60"(1524mm)MAX. (1829mm) MAX. WOOD TRUSS WEB MEMEBER CEILING =Mad...a LW= BOTTOM OF PIPE/ J W�% TOP OF CHORD \\\\\\\\\\\\\\\\\\\\\\\\\CS`\\\\\\\\\\N`\"\N\\\\\\\\\\\\\\\\\\\\\\\ WHEN OFFSETTING CPVC PIPE OVER AN OBSTRUCTION A GL5608 MODEL"IC"SPRINKLER MUST BE INSTALLED DIRECTLY ON THE PIPE OVER THE OBSTRUCTION. 6"(152mm)MAX.ABOVE CEILING OR NON-COMBUSTIBLE CEILING INSULATION.OR 113 THE DEPTH OF CONCEALED- AREA(AS MEASURED FROM TOP SURFACE OF CEILING TO TOP SURFACE OF JOIST INSULATION ABOVE),OR WHICH EVER IS SMALLER. WHEN THE LOWER JOIST IS GREATER THAN 6"(152rnm)IN HEIGHT CPVC PIPING IS PERMITTED TO BE ATTACHED DIRECTLY TO THE TOP OF THE JOIST. FIGURE 2: CPVC PIPE NON-COMBUSTIBLE INSULATION FILLED UPPER DECK SOLID WOOD, COMPOSITE WOOD JOIST, OR WOOD TRUSS CONSTRUCTION STEEL PIPING DESIGN REQUIREMENTS _ SYSTEM TYPE DRAFT CURTAINS Wet pipe system and dry type systems. Draft Curtain for Unobstructed wood truss construction and noncombustible bar joist construction must be 8"(203.2mm) ALLOWABLE CONSTRUCTION in height or one third of the depth of the concealed space, whichever is greater. Draft curtains must be constructed of TYPES a material that will not allow for heat to escape through or • Unobstructed wood truss construction' above them. • Unobstructed bar joist construction' Draft Curtain for Obstructed wood truss and solid wood joist • Solid wood joist construction2 construction must be 6" (152.4mm) in height or one third of the depth of the concealed space, whichever is greater. • Obstructed wood truss construction2 Draft curtains must be constructed of a material that will not • Non-combustible insulation filled solid wood joist allow for heat to escape through or above them. construction3 • Non-combustible insulation filled composite wood joist DEFLECTOR POSITION construction3 • 1 1/2 to 4 inches below the upper deck for unobstructed NOTE: wood truss and bar joist constructions. Deflector must Upper joist/truss cannot be more than 4"(101.6mm)in height. be below the bottom of the top chord in trusses or below 2 Upper joist/truss cannot be more than 12"(304.8mm)in height. bottom of joist. 3 The joist space in non-combustible insulation filled joist construction must be • completely filled with noncombustible insulation and secured in place by metal 1 1/2 to 4 inches below the joists for noncombustible wire netting to hold the insulation in place in the event of a fire. insulation filled solid and composite wood joist construction. PARTITION REQUIREMENTS • 1 '/2 to 2 inches below the joist or truss for solid wood For unobstructed wood truss construction, unobstructed joist or obstructed truss construction. bar joist construction, solid wood joist construction, and • 4 '/2 inches away from trusses obstructed wood truss construction the concealed space being protected must be broken up into areas no greater BLOCKING than 1000 square feet either by full height walls or by draft For solid wood joist and obstructed wood truss construction curtains. blocking must be provided in each of the channels between Noncombustible insulation filled joist construction is not re- the upper joists or trusses. The blocking must be located quired to be broken up into partitioned areas. where the draft curtains intersect the channels. The block- - ing must be installed to the full depth of the joists and be - installed as to not allow heat to escape through or above the blocking. The blocking must be installed using either the same material as the joists or a noncombustible material. NOV 2018 REV. B GFS-600 (Formerly A-40) Page 4 of 6 CONCEALED SPACE SIZE All spaces must have a minimum open space (from top of size. They must not have a total concealed space height of lower joist, cord, or truss to bottom of upper joist, cord, or greater than 72"(1.8m). This allows for a maximum lower truss) of 6"(152.4mm)(see Figures 3, 4, and 5). joist space of 12"(304.8mm) (see Figure 4). Unobstructed wood truss and bar joist construction must not Solid wood joist and obstructed truss construction must have a total concealed space height of more than 60"(1.5m). not have an open space (from top of lower joist or truss to (see Figure 3). bottom of upper joist or truss) of greater than 60"(1.5m) in Joist construction with noncombustible insulation in the size. They must not have a total concealed space height of upper deck must not have an open space (from top of lower greater than 84"(2.1m). The upper joist space must not be ' joist to bottom of upper joist) of greater than 60"(1.5m) in greater than 12"(304.8mm) in depth(see Figure 4). 4 1/2"(114mm)MIN.TS UPPER DECK FACE OF WOOD TRUSS OR 1 112"(38mm)MIN. TOP CHORD OF BAR JOIST DEFLECTOR MUST BE 4"(100mm)MAX. BELOW BOTTOM OF TOP IM.... N' CHORD TOP CHORD % I e, 4"(100mm)MAX. % 2 e ' s L5608 - (MODEL IC SPRINKLER) 11‘ I FRAME ARMS MUST - ��r� (1524mm) BE INSTALLED IN-LINE WITH PIPE RUN (152mm) MIN6" MAX.. �a�r _ %. / / EILING - FIGURE 3: STEEL PIPE UNOBSTRUCTED WOOD TRUSS OR NON-COMBUSTIBLE BAR JOIST CONSTRUCTION 2x FLOOR SOLID WOOD JOISTS/OBSTRUCTED TRUSS UPPER DECK 16"(406mm)ON CENTER T.12"(305 m) Mr F1 2"(51 m8m)MAXN L5608 FRAME ARMS MUST -- (MODEL IC SPRINKLER) 84" BE INSTALLED I (2134mm) IN-LINE WITH PIPE RUN MI MAX. I IMIMI 6"(152mm)MIN. EILING 60"(1524mm) MAX. V FRAMING �V�I P CEILING FIGURE 4: STEEL PIPE OBSTRUCTED WOOD TRUSS OR SOLID WOOD JOIST CONSTRUCTION NOV 2018 REV. B GFS-600 (Formerly A-40) Page 5 of 6 UPPER DECK NON-COMBUSTIBLE 2x FLOOR SOLID INSULATION COMPOSITE WOOD JOIST WOOD JOIST Vein1uIIfuaY;1914WutIVA �u1uAZ>,'� tuVA kite 1tI//1lt 'rtt/r1t/1it� 1I. u.r.n. n . ttuun .r/•1 1 4!(21'0(23mmmm) M)MAXIN. . INSULATION MUST BE HELD L5608 - IN PLACE WITH METAL - (MODEL IC SPRINKLER) _ i WIRE NETTING ir r i 6"(152mm)MIN. NI -Y- 60"(1524mm)MAX. FRAME ARMS MUST BE INSTALLED ' 72' IN-LINE WITH PIPE RUN (1829mm) MAX. CEILING FRAMING �Y �+� i x/_ A , VAAAAIVAAAAAA N.A A.\N N VAAAAAAA.AAAAAAAINNNO CEILING FIGURE 5: STEEL PIPE NON-COMBUSTIBLE INSULATION FILLED UPPER DECK SOLID WOOD OR COMPOSITE WOOD JOIST CONSTRUCTION ORDERING INFORMATION GLOBE® PRODUCT Quantity • SIN • Style • Orifice *Thread Size WARRANTY Temperature • Finishes • Desired Quantity Globe agrees to repair or replace any of its own manu- factured products found to be defective in material or work- Wrench - P/N 325390 manship for a period of one year from date of shipment. For specific details of our warranty please refer to Price List Terms and Conditions of Sale (Our Price List). 4077 Airpark Dr. Technical Support - Standish, MI 48658 1-800-248-0278 www.globesprinkler.com Ph. 989-846-4583 techservice@globesprinkler.com ""' '.7.. NOV 2018 REV. B GFS-600 (Formerly A-40) Page 6 of 6 ir GLBE 4077 Airpark Dr. Standish, MI 48658•989-846-4583•www.globesprinkler.com 0 Technical Support•989-414-2600•techservice@globesprinkler.com SERIES GL-RES RESIDENTIAL PENDENT AND RECESSED Pg-IgeT K-FACTOR: 3.0, 4.1, 4.9, 5.6 ED JAN 7 2020 GENERAL DESCRIPTION ,RCITY OF TIGARD Uf G IVISION The series GL-RES pendent sprinklers are decorative fast response glass bulb sprinklers specifically tested and List- ed for use in residential applications such as homes, apart- ments, hotels, and dormitories to provide control of these k: K residential type fires and to improve the chance for occu- pants to escape. They utilize a 3mm frangible glass bulb as its heat sensing operating element. The recessed version of each of these Residential Sprinklers is intended for use in areas with finished ceilings. It employs a two-piece Re- SERIES GL-RES cessed Escutcheon. The Recessed Escutcheon provides a GL3010, GL4110, GL4910, GL5610 total adjustment of 1/2 inch (12.7mm)from the flush ceiling position or ±1/4 inch (6.4mm) of recessed adjustment. The adjustment provided by the Recessed Escutcheon reduces TECHNICAL DATA _ the accuracy to which the pipe drops to the sprinklers must be cut. Approvals • See TABLE A -This sprinkler may be installed within dwelling occupancies Maximum Working Pressure as allowed by NFPA 13, 13D, 13R and any other related • 175 psi (12 bar) documents as appropriate. Temperature Rating The GL3010 is typically utilized when maximum coverag- ° See TABLE A es are not needed, thereby reducing flow demands. The K-Factor• " '/2 GL5610 is typically the sprinkler of choice when utilizing GL3010 K3.0 gpm/psi�2 (43.2 Ipm/bar/2) • Residential Sprinklers within an NFPA 13 Occupancy. The GL4110 K4.1 gpm/psis/2 (59.0 Ipm/bar��) • larger K-factor can be advantageous when needed to con • GL491 Q K4.9 gpm/psi��2 (70.6 Ipm/bars/2) ) form to the NFPA 13 hydraulic Special Design Approach for GL5610 K5.6 gpm/psi {80.6 Ipm/bar Residential Sprinklers. Thread Size • 1/2" NPT(15 mm) Length • 2-1/2" (6.3 cm) Materials of Construction OPERATION • Frame- bronze • Deflector- brass • Screw - brass Upon exposure to heat such as from a fire, the fluid in the • Lodgement Wire (GL5610 only)-stainless steel • Bulb bulb expands, compressing the air bubble within the bulb. seat copper When the air bubble can no longer compress, the fluid ex- ° Spring - nickel alloy • Seal -teflon • pansion causes breakage of the glass bulb, resulting in re- Bulb- glass with alcohol based solution, 3mm lease of the water seat assembly, and discharge of water ° Escutcheon Assembly-carbon steel from the sprinkler. FINISHES AND ACCESSORIES Finishes • Factory Bronze • Chrome •White Polyester NOTE: • Black Polyester-special order - Users should refer to Globe's web site (www.globesprinkler.com) Escutcheons - to assure that the most recent technical literature is being utilized. • Brass•Chrome•White Polyester• Black Polyester Wrenches •Standard • Recess• 1/2" NPT APRIL 2019 REV.A GFS-302 PAGE 1 of 4 DESIGN CRITERIA The Globe Residential Pendent Sprinkler Series GL-RES is Hydraulic Design (NFPA 13) cULus Listed for installation in accordance with this data The minimum required discharge from each design area sheet as well as the applicable installation Standard being sprinkler shall be the greater of the following: utilized. (1) In accordance with minimum flow rates indicated in Globe Residential Sprinkler Installation Guide TABLE A. (2) In rooms or compartments greater than 800 ft2 When conditions exist that are outside the scope of the pro- (74.3 m2), calculated based on delivering a minimum _ vided criteria, refer to the Globe Residential Sprinkler Instal- of 0.1 gpm/ft2 (4.1 mm/min) over the coverage area of lation Guide (Document GFS-380) for recommendations each sprinkler, calculated in accordance with the that may be acceptable to the authority having jurisdiction. S x L Rules for density area sprinklers. Hydraulic Design (NFPA 13D and 13R) (3) In rooms or compartments 800 ft2 (74.3 m2) or less (Defined as "Small Rooms") calculated based on de- For systems designed to NFPA 13D or NFPA 13R, the min- livering a minimum of 0.1 gpm/ft2 (4.1 mm/min)over imum required sprinkler flow rate is given in Table A for the the room or compartment using the area of the room coverage areas shown. The sprinkler flow rate is the min- divided by the number of sprinklers in the room. (7psi imum required discharge from each of the total number of minimum) "design sprinklers" as specified in NFPA 13D or NFPA 13R. TABLE A: NFPA 13, 13R, AND 13D HYDRAULIC AND INSTALLATION DESIGN CRITERIA DEFLECTOR TO MINIMUM K TEMPERATURE MAX.AREA OF MINIMUM MINIMUM CEILING/ DISTANCE FACTOR MOUNTING SIN COVERAGE PRESSURE FLOW BETWEEN GPM/PS/ SURFACE (lpm ha7') FEET(m) PSI(bat) GPM(11min.) DISTANCE SPRINKLERS _ 155°F 175°F 200°F INCHES(mm) FEET(m) (68°C) (79°C) (93°C) cULus cULus cULus 12(3.6)x 12(3.6) 7.1 (.49) 8.0(30.3) 3.0 EU` GL3010 (43.2) cEUUus cULus cULus 14(4.3)x 14(4.3) 11.1 (.765) 10.0(37.8) cULus cULus EU()) EU(I) NA 12(3.6)x 12(3.6) 7.2(.5) 11.0(42) Smooth Ceilings 41 cULus (4.3) ( ) ( ) Recessed 1/829 GL4110 (59) EUI NA NA 14x 14 4.3 8.6(.59) 12.0 45 (29) to 1-5/8(41) cULus EU' cULus NA 16(4.9)x 16(4.9) 11.7(.81) 14.0(53) Smooth Ceilings cULus cULus Exposed EU` 1) EUI NA 12(3.6)x 12(3.6) 7.0(.48) 13.0(49) Max.4(101.6) cULus cULus Beamed Ceilings EU�1) EU NA 14(4.3)x 14(4.3) 8.2(.57) 14.0(53) g Adjacent 8(2.4) 4.9 cULus cULus per NFPA 13, 13D, GL4910 (70 6) EU'1) EU'I NA 16(4.9)x 16(4.9) 8.2(.57) 14.0(53) or 13R as appropriate cULus cULus Elio) Rim NA 18(5.5)x 18(5.5) 12.0(.83) 17.0(64) Beamed Ceilings cULus cULus In Beam EU"> EU") NA 20(6.1)x 20(6.1) 16.7(1.15) 20.0(76) 14"Max. Beam Depth 1-1/8(29) cULus NA NA 12(3.6)x 12(3.6) 7.2(.5) 15.0(57) to 1-5/8(41) 5.6 cULus NA NA 16(4.9)x 16(4.9) 11.5(.79) 19.0(72) GL5610 (80.6) cULus NA NA 18(5.5)x 18(5.5) 14.1 (.97) 21.0(79) cULus NA NA 20(6.1)x 20(6.1) 18.4(1.27) 24.0(91) NOTE: Deflector-to-Ceiling Distance Criteria reflects 2019 Edition of NFPA 13D and 13R. ''LISTED BY UNDERWRITERS LABORATORIES,INC.FOR USE IN THE U.S.,CANADA, AND EUROPEAN UNION. APRIL 2019 REV.A GFS-302 PAGE 2 of 4 INSTALLATION NOTICE Do not install any bulb-type sprinkler if the bulb is cracked or there is loss of liquid from the bulb. Sprinklers should be tightened enough to obtain a leak-tight joint when water pressure is applied and/or hydrostatic test is performed. Sprinklers should not be overtightened as this can result in distortion and subsequent leak- age. It is recommended not to exceed 14 ft.-lb. (19.0 Nm) torque FIGURE 1: STANDARD WRENCH • for 1/2 inch NPT sprinkler threads. P/N 325390 Step1. Sprinklers must be properly oriented. Step2. With pipe thread sealant applied to the pipe threads, hand tighten the sprinkler into the sprin- kler fitting. Note:Do not grasp the sprinkler by ' t the deflector. Step3. Wrench-tighten the sprinkler using only thelort appropriate wrench. Wrenches are only to be ,[ applied to the sprinkler wrench flats or wrench hex as applicable. Note:Do not apply wrench to FIGURE 2: RECESSED WRENCH frame arms. P/N 325391 CARE AND MAINTENANCE Prior to installation, it is important to read and follow the "Sprinkler Caution" sheet (GFS-840) included within each box of sprinklers. This sheet is available on Globe's web site(www.globesprinkler.com). - Always obtain permission from the proper authorities to 215/18"DIA shut down the affected fire protection system and notify all DIA -personnel who may be affected by this action before closing HOLE INCELNG a fire protection system main control valve for maintenance 29/32"DIA work on the system that it controls. I I Sprinklers should only be cleaned by means of gently dust- ing with a feather duster; otherwise, non-operation in the / event of a fire or inadvertent operation may result. / +°X112'REDUCER ACE OF FTG. Store sprinklers in a cool, dry place. Exposure to extreme _ heat will damage the thermal sensing element, possibly re- '`ikA, �\ yr MAX. suiting in premature activation.Avoid direct sunlight. .�� -\\1\�o any sprinkler that shows any corrosion, damage, ,' — Replace t-,/e ELNG or loss of liquid from the glass bulb. 1118"MN.(REF.) RETANER 1 5/8"MAX.(REF.)* Do not attempt to paint or alter the sprinkler's coating in any manner after leaving the manufacturing plant. . * (NNER RETANER FLUSH WITH CELNG) Do not attach wiring, ropes, decorations or fixtures to a sprinkler. FIGURE 3: 1/2"ADJUSTMENT RECESSED PENDENT Absence of an escutcheon, used to cover a ceiling hole, may delay sprinkler operation in a fire situation. It is the owner's responsibility for inspection, testing and maintenance of the fire sprinkler system with all components and devices in accordance with the National Fire Protection Association Pamphlet 25 as well as any other requirements as set forth by the local Authority Having Jurisdiction (AHJ). 4077 Airpark Dr. Standish, MI 48658•989-846-4583•www.globesprinkler.com Technical Support•989-414-2600•techservice@globesprinkler.com APRIL 2019 REV.A GFS-302 PAGE 3 of 4 ORDERING INFORMATION TABLE B: PART NUMBER SELECTION PART NUMBER SIN + TEMPERATURE + FINISH XXXX XXX XX SIN TEMPERATURE FINISH GL3010 3010 155 155°F(68°C) 01 BRONZE GL4110 4110 175 175°F(79°C) 02 CHROME GL4910 4910 200 200°F(93°C) 03 WHITE POLYESTER GL5610 5610 04 BLACK POLYESTER Note:All combinations may not be available. Refer to TABLE A for available listed combinations TABLE C: ESCUTCHEONS 1/2"(13mm)ADJUSTABLE RECESSED ESCUTCHEON FINISH FRICTION FIT 1/2"NPT THREADED 1/2"NPT • Chrome 332071 329301 White Polyester 332073-W 329303-W Brass 332072 NA Black Polyester 332073-B NA SPECIFY: • SPRINKLER •Quantity•SIN•Temperature Rating• Finish •Part Number(See TABLE B) • ESCUTCHEON •Quantity•Finish• Part Number (See TABLE C) GLOBO PRODUCT WARRANTY • WRENCH •Quantity•Part Number Globe agrees to repair or replace any of its manufactured 1/2"NPT Standard 325390 products found to be defective in material or workmanship 1/2"NPT Recess 325391 for a period of one year from date of shipment. • PROTECTIVE CAPS •Quantity•Part Number For specific details of our warranty please refer to Price List Cap 327109-Cap Terms and Conditions of Sale (Our Price List). APRIL 2019 REV.A GFS-302 PAGE 4 of 4