Report (50) Oregon Residential Specialty Code N1107.2
HIGH-EFFICIENCY INTERIOR LIGHTING SYSTEMS
Permit No.: s s (NE —�(� 3 Jurisdiction:
Site Address: ( tC w -75514 ,71 a rz 5)6
Subdivision/Lot#:
and/or
Map and Tax Lot#:
By my signature below, I certify that a minimum of fifty(50)percent of the permanently
installed lighting fixtures in the above mentioned building have been installed with compact or
linear fluorescent, or a lighting source that has a minimum efficacy of 40 lumens per input watt.
(Oregon Residential Specialty Code N1107.2)1
Signature: 722 �" v� )'- �� Date: (9
Owner/General Contractor/Authorized Agent
Print Name: ,r 1z----
1 ORSC Section N1107.2.High-efficiency interior lighting systems. A minimum of fifty(50)percent o the
permanently installed lighting fixtures shall be installed with compact or linear fluorescent,or a lighting source that
has a minimum efficacy of 40 lumens per input watt. Screw-in compact fluorescent lamps comply with this
requirement.
The building official shall be notified in writing at the final inspection that a minimum of fifty percent of the
permanently installed lighting fixtures are compact or linear fluorescent,or a minimum efficacy of 40 lumens per
input watt.
I:\Build ng\Fotms\RES-HighEfficiencyLighting.doc 07/01/08
Oregon Residential. Specialty Code 8318.2
MOISTURE CONTENT ACKNOWLEDGEMENT FORM
I, � v t am the general contractor or the owner-builder
at the following address:
Site Address: (0(.093 (A) F
City: „St KlJvJ
Permit#: -- (-3-0 I�, -
Subdivision/Lot#: ; , �' 61-- (/3
and/or
Map and Tax Lot#:
To conform with the 2008 Oregon Residential Specialty Code(ORSC), Section 8318.2 and
OAR 918-480-0140, I am notifying the building official that I am aware of the moisture content
Requirement of ORSC Section R318.2 and have taken steps to meet this code requirement.
[Section 8318.2 is provided for reference].
R318.2 Moisture Content: Prior to the installation of interior finishes,the building
official shall be notified in writing by the general contractor that all moisture-sensitive
wood framing members used in construction have a moisture content of not more than 19
percent by dry weight of dry framing members.
Signature: + J Date: U '4 I
General Contractor or Owner-Builder
I:\BuildinglForm\RES-MoistureSensitiveWood.doc 09/25/08
Oregon Residential Specialty Code R408.1
MOISTURE BARRIER ACKNOWLEDGEMENT FORM
- , am the general contractor or the owner-builder
at the following address:
Site Address: l �(2(� 3
l -f
City:
_5(M.Jr Aon
Permit#: $ ( cv 1'3— Co 9. 73
Subdivision/Lot#: 461/1
and/or
Map and Tax Lot#:
To conform with the 2014 Oregon Residential Specialty Code(ORSC), Section R408.1
Ventilation.I am notifying the building official that I have installed the Moisture Barrier as per
Requirement in ORSC Section 408.1 and have taken the following steps to meet this code
requirement:
E The ground surface of the under-floor space is covered with 6-mil black polyethylene
sheeting with
Joints lapped 12"at seams and
An Extending up the foundation walls 12".
Signature:
To "�- Date: 2-3
General Contractor or Owner-Builder
I:iBuildingWon ES-MoistureBarrier.doc 09/13/2016
,
flir 0 ,
Property Address: ii, to _...1,..b4
Conditioned Floor Area: Date 8e7"2..3 .19
Builder or Registered esitcli Professional:
1:9
Signature: . Nri, ‘
Notes 1....„. # c....:9„,,L1 3
a a
v 1 i I '
4,",,,,,,,W,A,,, 't.;4•44,..4:4,.....',..1,,,,,:.:
p
EFFICIENCY - DURABILITY - COMFORT
T1 - Duct Test Results ,,
or Area x 0.06= Test Method: Leakage to outside Y/N Total Lekage Y/N
Test Results: CFM @ 50 PA Fan Pressure PA Ring Size open: 1/2 /3
'
,
Duct Blaster Location: Pressure Tap Location:
Building air leakage target:ACH50<5.0—Tested leakage: ACH50 OP v __
it, . l