Report (78) FVsao\U - ocx�S
4 AY 611,
`�� W VAT T
FIRE PROTECTION, INC.
9095 S.W. Burnham
Tigard, OR 97223
SOUTHVIEW LOT #14
12007 SW AUTUMN VIEW AVE
TIGARD, OR 97224
FIRE PROTECTION
EQUIPMENT SUBMITTAL
tqco Worldwide
www.tyco-fire.com
Fire Protection Contacts
Products
RAPID RESPONSE Series LFII Residential Sprinklers
4.9 K-factor Flat-Plate Concealed Pendent
Wet Pipe and Dry Pipe Systems
General proven to help in the control of residen-
tial fires and to improve the chance for
Description occupants to escape or be evacuated.
The Series LFII Residential Flat-Plate
•
The TYCO RAPID RESPONSE Series Concealed Pendent Sprinklers are
LFII Residential Flat-Plate Concealed shipped with a Disposable Protective 111110.1 "-
Pendent
_Pendent Sprinklers(TY2524)are decora- Cap.The Protective Cap protects the
tive,fast response,fusible solder sprin- sprinkler during ceiling installation or
klers designed for use in residential oc- finish.After ceiling installation is corn
cupancies such as homes,apartments, plete, the Protective Cap is removed ry
dormitories,and hotels. and the Cover Plate/Retainer Assem-
44-
The Cover Plate/Retainer Assembly con-
tive
is installed. Removing the Protec-
ceals the sprinkler operating compo- tive Cap is required for proper sprinkler
nents above the ceiling.The flat profile performance. The owner is responsible for maintaining
of the Cover Plate provides the optimum Dry Pipe System Application their fire protection system and devic-
aesthetically appealing sprinkler design. The Series LFII Residential Flat-Plate es in proper operating condition. Con-
Additionally,the concealed design of the Concealed Pendent Sprinkler offers a tact the installing contractor or sprinkler
Series LFII Residential Flat-Plate Con- laboratory approved option for design manufacturer with any questions.
cealed Pendent Sprinklers provides 1/2 ing dry pipe residential sprinkler sys-
inch(12,7 mm)vertical adjustment.This
adjustment provides a measure of flex- tems,whereas,ebmost residentialppesprin- Sprinkler
ibility when cutting fixed sprinkler drops. klers are laboratory approved for wet
systems only. Identification
The Series LFII Residential Flat-Plate Through extensive testing, it has been
Concealed Pendent Sprinklers are in- determined that the number of design Number (SIN)
tended for use in the following systems: sprinklers(hydraulic design area)for the
•wet and dry pipe residential sprin- Series LFII Residential Flat-Plate Con- TY2524
kler systems for one- and two-fam- cealed Sprinklers(TY2524)need not be
ily dwellings and mobile homes per increased over the number of design
NFPA 13D sprinklers(hydraulic design area)speci-
•wet and dry pipe residential sprin- fied for wet pipe sprinkler systems, as
kler systems for residential occu- is customary for density/area sprinkler
pancies up to and including four sto- systems designed per NFPA 13, 13D,
ries in height per NFPA 13R or 13R.
•wet and dry pipe sprinkler systems Consequently,the Series LFII Residen-
for the residential portions of any tial Flat Plate Concealed Sprinklers
occupancy per NFPA 13 (TY2524)offer the features of non-wa-
ter filled pipe in addition to not having to
The Series LFII Residential Sprinklers increase the number of design sprinklers
have been designed with heat sensitiv- (hydraulic design area)for systems de-
ity and water distribution characteristics signed to NFPA 13, 13D,or 13R.
NOTICE
The Series LFII Residential Flat-Plate
IMPORTANT Concealed Pendent Sprinklers(TY2524)
Always refer to Technical Data described herein must be installed and
Sheet TFP700 for the `INSTALLER maintained in compliance with this doc-
WARNING"that provides cautions ument and the applicable standards of
with respect to handling and instal- the National Fire Protection Association,
lation of sprinkler systems and com- in addition to the standards of any au-
ponents. Improper handling and in- thorities having jurisdiction. Failure to
stallation can permanently damage do so may impair the performance of
a sprinkler system or its compo- these devices.
nents and cause the sprinkler to fail
to operate in a fire situation or cause
it to operate prematurely.
Page 1 of 6 FEBRUARY 2014 TFP443
TFP443
Page 2 of 6
BODY ' ` SEALING WRENCH
(1/2"NPT) J, ASSEMBLY RECESS
CAP �` /l� \ A 41
�j', SPRINKLER
rt ■S - WRA EAING
SADDLE I` \ -
PUSH WRENCH
COMPRESSION
SUPPORT t ill INTO ENSURE
CUP WITH 1 ENGAGEMENT
ROLL FORMED t� {/ SCREW WITH SPRINKLER
THREADS ) WRENCHING AREA
� LEVER FIGURE 2
__— R W-TYPE 18
GUIDE Ir7c '11I SPRINKLER WRENCH
PIN � `, a
SOLDER LINK
ELEMENT
GUIDE PIN
HOUSING
DEFLECTOR
(OPERATED
OPERATED
DEFLECTOR 1---�-- POSITION)
SPRINKLER/SUPPORT CUP
ASSEMBLY
THREAD INTO I I RETAINER
SUPPORT I WITH THREAD
CUP UNTIL J I DIMPLES
MOUNTING \ O O I�
SURFACE IS 2
FLUSH WITH
CEILING EJECTION
SPRING
-� i
SOLDER JJJJJJ COVER PLATE/RETAINER COVER
TAB ASSEMBLY PLATE
FIGURE 1
RAPID RESPONSE SERIES LFII RESIDENTIAL
FLAT-PLATE CONCEALED PENDENT SPRINKLER(TY2524)
2-1/2"DIA. SPRINKLER-
~ (63,5 mm) ~ 1/2"(12,7 mm) FACE OF SUPPORT CUP
1/2" \ THREADED SPRINKLER ASSEMBLY
NPTADJUSTMENT FITTING
/ OPERATED
iWirTh-mi-I-1.1 r SPRINKLER x—_---------,1=1
ii
_1-7/8"±1/4" - COVER InI
mm PLATE
�_ = I I 1/8"GAP 6,4 mm) RETAINER
_ (3,2 mm)
i -1•11111 -
ii
-----' IMO 1
} 7/8"(22,2 mm)
COVER- SPRINKLER- jMOUNTING 1-1/8"(28,6 mm
RETAINER SUPPORT CUP 3/16" SURFACE \ ) M1
ASSEMBLY ASSEMBLY (4,8 mm)
3-3/16"DIA. DISPOSABLE DEFLECTOR IN
(81,0 mm) TIP PROTECTIVE CAP OPERATED POSITION
FIGURE 3
RAPID RESPONSE SERIES LFII RESIDENTIAL FLAT-PLATE(TY2524)
INSTALLATION DIMENSIONS/PROTECTIVE CAP/ACTIVATED DEFLECTOR
TFP443
Page 3 of 6
Technical Design Criteria Dry Pipe System Water Delivery
When using the Series LFII Residential
Data The TYCO RAPID RESPONSE Series Flat-Plate Concealed Pendent Sprinklers
LFII Residential Flat-Plate Concealed (TY2524)in dry pipe sprinkler systems,
Approvals Pendent Sprinklers (TY2524) are UL the time for water delivery must not ex-
UL and C-UL Listed and C-UL Listed for installation in ac- ceed 15 seconds for the most remote
The TYCO RAPID RESPONSE Series
cordance with this section: operating sprinkler.
LFII Residential Flat-Plate Concealed Residential Sprinkler Design Guide Obstruction to Water Distribution
Pendent Sprinklers are only listed with When conditions exist that are outside Sprinklers are to be located in accor-
the Series LFII Concealed Cover Plates the scope of the provided criteria, re- dance with the obstruction rules of
having a factory-applied finish. fer to the Residential Sprinkler Design NFPA 13D, 13R,and 13 as applicable
These Cover Plates and their part num- Guide TFP490 for the manufacturer's for residential sprinklers as well as with
bers can be found in the Ordering Pro- recommendations that may be accept- the obstruction criteria described within
cedure section at the end of this data able to the authority having jurisdiction. the Technical Data Sheet TFP490.
sheet. System Type Operational Sensitivity
For details on approvals,refer to the De- Per the UL Listing,wet pipe and dry pipe Install sprinklers relative to the ceiling
sign Criteria section. systems may be utilized.Per the C-UL mounting surface as shown in Figure 3.
Listing,only wet pipe systems may be The Series LFII Residential Flat-Plate
Maximum Working Pressure utilized.
175 psi(12,1 bar) Concealed Pendent Sprinklers must
Refer to Technical Data Sheet TFP485 not be used in applications where the
Discharge Coefficient about the use of Residential Sprinklers air pressure above the ceiling is greater
K=4.9 GPM/psi12(70,6 LPM/bar12) in residential dry pipe systems. than that below. Down drafts through
the Support Cup can delay sprinkler op-
Temperature Rating Ceiling Types eration in a fire situation.
Sprinkler: 160°F(71°C) Smooth flat horizontal,or beamed, or
Cover Plate: 139°F(59°C) sloped, in accordance with the 2013 Sprinkler Spacing
Edition of NFPA 13D, 13R or 13 as The minimum spacing between sprin-
Vertical Adjustment applicable. klers is 8 feet (2,4 m). The maximum
1/2 inch(12,7 mm) spacing between sprinklers cannot ex-
Hydraulic Design ceed the length of the coverage area
Finishes (NFPA 13D and 13R) (Table A)being hydraulically calculated
Refer to the Ordering Procedure section. For systems designed to NFPA 13D or (e.g.,a maximum of 12 feet for a 12 ft.x
Physical CharacteristicsNFPA 13R,the minimum required sprin- 12 ft.coverage area or 20 feet for a 20
Plate/Retainer Assembly: kler flow rate are given in Tables A and ft.x 20 ft.coverage area.)
CoveCover Plate Copper B as a function of temperature rating
Ejection Spring Stainless Steel and the maximum allowable coverage
Retainer Brass areas.The sprinkler flow rate is the mini-
Sprinkler/Support Cup Assembly: mum required discharge from each of
Body Brass the total number of"design sprinklers"
Cap Bronze as specified in NFPA 13D or NFPA 13R.
Saddle Brass The number of"design sprinklers"spec-
Sealing Assembly Beryllium ified in NFPA 13D and 13R for wet pipe
Nickel w/TEFLON systems is to be applied when designing
Soldered Link Halves Nickel dry pipe systems.
Lever Bronze
Compression Screw Brass Hydraulic Design
Deflector Bronze (NFPA 13)
Guide Pin Housing Bronze For systems designed to NFPA 13,the
Guide Pins Bronze number of design sprinklers is to be
Support Cup Steel the four most hydraulically demanding
Operation sprinklers.The minimum required dis-
charge from each of the four sprinklers
When exposed to heat from a fire, the is to be the greater of the following:
Cover Plate,which is normally soldered •The flow rates given in Tables A and
to the Retainer at three points,falls away B as a function of temperature rating
to expose the Sprinkler/Support Cup As- and the maximum allowable cover-
sembly.At this point,the Deflector,sup- age area
ported by the Guide Pins, drops down •A minimum discharge of 0.1 gpm/ft2.
to its operated position. over the"design area" comprised of
The Solder Link Element of the Sprinkler/ the four most hydraulically demand-
Support Cup Assembly is comprised of ing sprinklers for the actual coverage
two link halves that are soldered togeth areas being protected by the four
er with a thin layer of solder.When the sprinklers
rated temperature is reached,the sol- The number of "design sprinklers"
der melts and the two link halves sepa- specified in NFPA 13 for wet pipe sys-
rate, allowing the sprinkler to activate tems is to be applied when designing
and flow water. dry pipe systems.
TFP443
Page 4 of 6
WET PIPE SYSTEM
Minimum Flow and Residual Pressureebe°)
Maximum Maximum
Cooveeraage Spacing Ordinary Temp Rating
ArFt. 160°F(71°C)
Ft.x Ft. Deflector to Installation Minimum
(m x m) (m) Flow Pressure Ceiling Type Spacing
GPM PSI
(L/min) (bar) (m)
12 x 12 12 13 7.0 Smooth
(3,7 x 3,7) (3,7) (49,2) (0,48) Ceilings 7/8 to
14 x 14 14 13 7.0 1-1/8 inches.
(4,3 x 4,3) (4,3) 49,2) (0,48) Beamed
16 x 16 16 13 7.0 Ceilings per 8
(4,9 x 4,9) (4,9) (49,2) (0,48) NFPA 13D Concealed (2,4)
13R,or 13
18 x 18 18 17 12.0 Installed in
(5,5 x 5,5) (5,5) (64,3) (0,83) beam 7/8 to
1-1/8 inches
20 x 20 20 20 16.7 below bottom
(6,1 x 6,1) (6,1) (75,7) (1,15) of beam
(a) For coverage area dimensions less than or between those indicated,use the minimum required flow for the next highest
coverage area for which Hydraulic Design section under the Design Criteria are stated.
(b) The Minimum Flow requirement is based on minimum flow in GPM(LPM)from each sprinkler.The associated residual pres-
sures are calculated using the nominal K-factor.Refer to"Hydraulic Design"in the Design Criteria section for details.
(c) For NFPA 13 residential applications,the greater of 0.1 gpm/ft.2 over the design area or the flow in accordance with the
criteria in this table must be used.
TABLE A
WET PIPE SYSTEM
SERIES LFII RESIDENTIAL FLAT-PLATE CONCEALED PENDENT SPRINKLER(TY2524)
NFPA 13D, 13R,AND 13 HYDRAULIC DESIGN CRITERIA
DRY PIPE SYSTEM
Maximum Maximum Minimum Flowand Residual Pressure)
Coverage Spacing Ordinary Temp Rating
Area�a Ft. 160°F(71°C)
Ft.x Ft. Deflector to Installation Minimum
(m x m) (m) Flow Pressure Ceiling Type Spacing
GPM PSI Ft.
(L/min) (bar) (m)
12 x 12 12 15 9.4 Smooth
(3,7 x 3,7) (3,7) (56,8) (0,65) Ceilings 7/8 to
14 x 14 14 15 9.4 1-1/8 inches.
(4,3 x 4,3) (4,3) (56,8) (0,65) Beamed
16 x 16 16 16 10,7 Ceilings per 8
(4,9 x 4,9) (4,9) (60,6) (0,74) NFPA 13D Concealed (2,4)
13R,or 13
18 x 18 18 17 12.0 Installed in
(5,5 x 5,5) (5,5) (64,3) (0,83) beam 7/8 to
1-1/8 inches
20 x 20 20 21 18,4 below bottom
(6,1 x 6,1) (6,1) (79,5) (1,27) of beam
(a) For coverage area dimensions less than or between those indicated,use the minimum required flow for the next highest
coverage area for which Hydraulic Design section under the Design Criteria are stated.
(b) The Minimum Flow requirement is based on minimum flow in GPM(LPM)from each sprinkler.The associated residual
pressures are calculated using the nominal K-factor.Refer to"Hydraulic Design"in the Design Criteria section for details.
(c) For NFPA 13 residential applications,the greater of 0.1 gpm/ft 2 over the design area or the flow in accordance with the
criteria in this table must be used.
TABLE B
DRY PIPE SYSTEM
SERIES LFII RESIDENTIAL FLAT-PLATE CONCEALED PENDENT SPRINKLER(TY2524)
NFPA 13D, 13R,AND 13 HYDRAULIC DESIGN CRITERIA
TFP443
Page 5 of 6
Installation Step 6.Screw on the Cover Plate/Re- Automatic sprinklers must never be
tainer Assembly until its flange contacts painted,plated,coated,or otherwise
The TYCO RAPID RESPONSE Series the ceiling. Do not continue to screw altered after leaving the factory.Modi-
LFII Residential Flat-Plate Concealed on the Cover Plate/Retainer Assembly fied or overheated sprinklers must be
Pendent Sprinklers must be installed in such that it lifts a ceiling panel out of replaced.
accordance with this section: its normal position. Care must be exercised to avoid dam-
If the Cover Plate/Retainer Assembly age to the sprinklers-before,during,
General Instructions cannot be engaged with the Mounting and after installation.Sprinklers dam-
Damage to the Solder Link Element dur- Cup or the Cover Plate/Retainer Assem- aged by dropping,striking,wrench twist/
ing installation can be avoided by han- bly cannot be engaged sufficiently to slippage,or the like,must be replaced.
dling the sprinkler by the Support Cup contact the ceiling,the Sprinkler Fitting
only;that is,do not apply pressure to the must be repositioned. The owner is responsible for the in-
Solder Link Element(Figure 1). spection,testing,and maintenance of
leak tight 1/2 inch NPT sprinkler joint their fire protection system and devices
Aheak-bleak-tight
t 1/2 by applying a mint Care and in compliance with this document, as
i
should
tbem obtained
m torque of 7 to 14 well as with the applicable standards of
im ft.-lbs. (9,o- to 19,mu Nm).rHigher levels (e.g.,Maintenance the National Fire Protection Association
of torque can distort the sprinkler inlet The TYCO RAPID RESPONSE Series dards NFPA tt,in addition to the ju-
withst -
consequent leakage or impairment LFII Residential Flat-Plate Concealed of any other authorities having trac-
of the sprinkler. Pendent Sprinkler Y2524 must be risdi or sprion.inkler
kler manufacturer the installing gacoding
P R ) for sprinkler regarding
Do not attempt to compensate for insuf- maintained and serviced in accordance any questions.
ficient adjustment in the Cover Plate/ with the section:
rec-
Retainer Assemblybyunder-or over- Automatic sprinkler systems are Before closing a fire protection system ommended to be inspected, tested,
tightening the sprinkler. Re-adjust the main control valve for maintenance work and maintained by a qualified Inspec-
position of the sprinkler fitting to suit. on the fire protection system that it con- tion Service in accordance with local
Step 1. Install pendent sprinklers in trols,obtain permission to shut down the requirements and/or national codes.
the pendent position,with the center- affected fire protection system from the
line of the sprinkler perpendicular to the proper authorities and notify all person-
mounting surface. nel who may be affected by this action.
Step 2. Remove the Protective Cap. Absence of a Cover Plate may delay the
sprinkler operation in a fire situation.
Step 3.With pipe-thread sealant ap-
plied to the pipe threads,and using the The owner must assure that the sprin-
W-Type 18 Wrench shown in Figure 2, klers are not used for hanging any ob-
install and tighten the Sprinkler/Sup- jects and that the sprinklers are only
port Cup Assembly into the fitting.The cleaned by means of gently dusting with
W-Type 18 Wrench accepts a 1/2 inch a feather duster;otherwise,non-opera-
ratchet drive. tion in the event of a fire or inadvertent
Step 4. Replace the Protective Cap by operation may result.
pushing it upwards until it bottoms out When properly installed,there is a nomi-
against the Support Cup.The Protec- nal 1/8 inch(3,2 mm)air gap between
tive Cap helps prevent damage to the the lip of the Cover Plate and the ceil- _
Deflector and Guide Pins during ceiling ing,as shown in Figure 3.This air gap
installation and/or during application of is necessary for proper operation of the
the finish coating of the ceiling. sprinkler by allowing heat flow from a
fire to pass below and above the Cover
NOTICE Plate to help assure appropriate release
of the Cover Plate in a fire situation.If the
As long as the protective Cap remains ceiling needs repainting after sprinkler
in place,the system is considered"Out installation,exercise care to ensure that
Of Service". the new paint does not seal off any of
Step 5.After the ceiling has been corn- the air gap.Failure to do so may impair
pleted with the 2-1/2 inch(63 mm)diam- sprinkler operation.
eter hole and in preparation for install- Factory painted Cover Plates must not
ing the Cover Plate/Retainer Assembly, be repainted.They should be replaced,
remove and discard the Protective Cap, if necessary, by factory painted units.
and verify that the Deflector moves up Non-factory applied paint may adversely
and down freely. delay or prevent sprinkler operation in
If the sprinkler has been damaged and the event of a fire.
the deflector does not move up and Do not pull the Cover Plate relative to the
down freely,replace the entire sprinkler Retainer.Separation may result.
assembly. Do not attempt to modify or Sprinklers which are found to be leaking
repair a damaged sprinkler.
or exhibiting visible signs of corrosion
must be replaced.
TFP443
Page 6 of 6
Limited
Warranty
For warranty terms and conditions,visit
www.tyco-fire.com.
Ordering
Procedure
Contact your local distributor for avail-
ability.When placing an order, indicate
the full product description and Part
Number(P/N).
Sprinkler/Support Cup Assembly
Specify:Series LFII(TY2524), K=4.9
(70,6),Residential Flat-Plate Concealed
Pendent Sprinkler without Cover Plate/
Retainer Assembly,P/N 51-114-1-160
Cover Plate/Retainer Assembly
Specify:Series LFII(TY2524), K=4.9
(70,6),Residential Flat-Plate Concealed
Pendent Sprinkler Cover Plate/Retain-
er Assembly with (specify)finish, P/N
(specify):
Ivory(RAL 1015) P/N 56-202-0-135
Beige(RAL 1001) P/N 56-202-2-135
Pure White(b)(RAL 9010) P/N 56-202-3-135
Signal White(a)(RAL 9003) P/N 56-202-4-135
Grey White(RAL 9002) P/N 56-202-5-135
Brown(RAL 8028) P/N 56-202-6-135
Black(RAL 9005) P/N 56-202-7-135
Brushed Brass P/N 56-202-8-135
Brushed Chrome P/N 56-202-9-135
Custom Paint P/N 56-202-X-135
(a)Previously known as Bright White.
(b)Eastern Hemisphere sales only.
Note: All Custom Cover Plates are
painted using Sherwin Williams Interior
Latex Paint. Contact TYCO Customer
Service with any questions related to
custom orders.
Sprinkler Wrench
Specify: W-Type 18 Sprinkler Wrench,
P/N 56-000-1-265
GLOBAL HEADQUARTERS 11400 Pennbrook Parkway,Lansdale,PA 19446 I Telephone+1-215-362-0700
Copyright®2014 Tyco Fire Products,LP. All rights reserved. fico
TEFLON is trademark of The DuPont Corporation. Fire Protection Products
Page 2 of 6 TFP1915
WATER
NOMINAL AVERAGE AVERAGE WEIGHT FT.OF PIPE WEIGHT PER LIFT
SIZE O.D. I.D. lbs./ft. FILLED WEIGHT PER LIFT lbs.
lbs./ft.
3/4" 1.050" 0.874" 0.18 0.44 7875 1339
1" 1.315" 1.101' 0.26 0.67 5040 1320
1-1/4" 1.660" 1.394" 0.42 1.08 2835 1191
1-1/2" 1.900" 1.598" 0.54 1.41 2205 1213
2" 2.375" 2.003" 0.84 2.20 1260 1084
2-1/2" 2.875" 2.423" 1.26 3.26 1215 1531
3" 3.500" 2.952" 1.87 4.83 720 1344
FIGURE 1—PIPE DIMENSIONS
Installation Care and
Tyco Fire and Building Products Maintenance
(TFBP) BlazeMaster CPVC Pipe and
Fittings are to be installed in accord- The owner is responsible for the fin-
ance with IH-1900, Rev. 0, January spection, testing, and maintenance of
2005"Installation Instruction&Techni- their fire protection system and de-
cal Handbook". vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
addition to the standards of any
authority having jurisdiction. The in-
stalling contractor or product manufac-
turer should be contacted relative to
any questions.
It is recommended that automatic
sprinkler systems be inspected,
tested, and maintained by a qualified
Inspection Service in accordance with
local requirements and/or national
codes.
NOTES
Before closing a fire protection system
control valve for inspection or mainte-
nance work on the fire protection sys-
tem that it controls,permission to shut
down the affected fire protection sys-
tem must first be obtained from the
proper authorities and all personnel
who may be affected by this action
must be notified.
After placing a fire protection system
in service,notify the proper authorities
and advise those responsible formoni-
- toring proprietary and/or central sta-
tion alarms.
TFP1915 Page 3 of 6
FITTING PART NOMINAL SIZE NOMINAL TAKE-OUT SCHD. WEIGHT
TYPE NUMBER (T/O) (lb.)
TEE 80000 3/4" 5/8" 40 0.11
/„/ T/O 80001 1" 11/16" 40 0.19
J �- 80002 1-1/4" 7/8" 40 0.26
.ii. 80003 1-1/2" 1-1/16" 80 0.51
•IENIM80004 2" 1-3/8" 80 0.90
T/0 ■■ T/O 80005 2-1/2" 1-9/16" 80 1.59
80006 3" 1-13/16" 80 2.41
XxYxZ X Y Z
80132 3/4"x 3/4"x 1" 3/4" 3/4" 5/8" 40 0.14
80133 1"x 3/4"x 3/4" 9/16" 9/16" 3/4" 40 0.14
80134 1"x 3/4"x 1" 3/4" 11/16" 3/4" 40 0.17
80260 1"x 1"x 3/4" 5/8" 5/8" 13/16" 40 0.16
80135 1-1/4"x 1"x 3/4" 5/8" 5/8" 15/16" 40 0.21
80136 1-1/4"x 1"x 1" 3/4" 3/4" 15/16" 40 0.22
80137 1-1/4"x 1"x 1-1/4" 15/16" 15/16" 7/8" 40 0.26
REDUCING TEE 80261 1-1/4"x 1-1/4"x 3/4" 5/8" 5/8" 7/8" 40 0.23
80262 1-1/4"x 1-1/4"x 1" 3/4" 3/4" 7/8" 40 0.26
Z 80138 1-1/4"x 1-1/4"x 1-1/2" 1" 1" 1" 80 0.43
1 i T/O
I.,0 80140 1-1/2"x 1-1/4"x 3/4" 9/16" 9/16" 1" 80 0.36
��� f 80141 1-1/2"x 1-1/4"x 1" 9/16" 9/16" 1-1/16" 80 0.38
:��. 80263 1-1/2"x 1-1/2"x 3/4" 9/16" 9/16" 1" 80 0.36
X.11111..1 Y I 80264 1-1/2"x 1-1/2"x 1" 9/16" 9/16" 1-1/16" 80 0.38
.411,21"F'''''- 80275 1-1/2"x 1-1/2"x 1-1/4" 7/8" 7/8" 1" 80 0.45
T/O • T/0 80265 2"x 2"x 3/4" 3/4" 3/4" 1-3/8" 80 0.61
80266 2"x 2"x 1" 7/8" 7/8" 1-3/8" 80 0.66
80274 2"x 2"x 1-1/4" 1-1/16" 1-1/16" 1-3/8" 80 0.74
80267 2"x 2"x 1-1/2" 1-1/8" 1-1/8" 1-3/8" 80 0.78
80271 2-1/2"x 2-1/2"x 1" 1-9/16" 1-9/16" 1-9/16" 80 1.43
80272 2-1/2"x 2-1/2"x 1-1/4" 1-9/16" 1-9/16" 1-9/16" 80 1.46
80273 2-1/2"x 2-1/2"x 1-1/2" 1-9/16" 1-9/16" 1-9/16" 80 1.48
80276 2-1/2"x 2-1/2"x 2" 1-9/16" 1-9/16" 1-9/16" 80 1.50
80270 3"x 3"x 1-1/2" 1-13/16" 1-13/16" 1-13/16" 80 2.28
80268 3"x 3"x 2" 1-13/16" 1-13/16" 1-3/4" 80 2.25
80269 3"x 3"x 2-1/2" 1-13/16" 1-13/16" 1-13/16" 80 2.44
CROSS&REDUCING CROSS 80009 3/4" 9/16" 40 0.13
80010 1" 11/16" 40 0.23
Jam„ __ T/0 80011 1-1/4" 15/16" 40 0.34
-ai-■ 80012 1-1/2" 1-1/16" 80 0.67
-EN.■ 80013 2" 1-5/16" 80 1.00
l„l� - 80014 2-1/2" 1-9/16" 80 1.91
il T/0 80008 3" 1-13/16" 80 2.89
T/0 ■■ T/0 80015 1"x 1"x 3/4"x 3/4" 7/8" 40 0.28
90°ELBOW& 80025 3/4" 5/8" 40 0.09
REDUCING ELBOW 80026 1" 3/4" 40 0.14
80027 1-1/4" 7/8" 40 0.21
X 80028 1-1/2" 1-1/16" 80 0.40
j„� T/0 80029 2" 1-5/16" 80 0.79
j. 80030 2-1/2" 1-9/16" 80 1.14
MOM
7.4'-Y 80031 3" 1-13/16" 80 1.82
„bra XxY X Y
- -T/O
80032 1"x 3/4" 11/16" 13/16" 40 0.16
FIGURE 2-FITTING DIMENSIONS(Part 1 of 4)
Page 4 of 6 TFP1915
FITTING PART NOMINAL TAKE-OUT WEIGHT
TYPE NUMBER NOMINAL SIZE SCHD.
(T/O) (lb.)
45°ELBOW 80050 3/4" 3/8" 40 0.08
T/O 80051 1" 3/8" 40 0.11
'�� 80052 1-1/4" 3/4" 40 0.20
''fir 80053 1-1/2" 1/2" 80 0.31
T/O''��i'�• 80054 2" 3/4" 80 0.56
4�• 80055 2-1/2" 13/16" 80 0.89
80056 3" 1" 80 1.19
80075 3/4" 1/8" 40 0.07
COUPLING& 80076 1" 1/8" 40 0.11
REDUCING COUPLING 80077 1-1/4" 3/16" 40 0.12
'!'' 80078 1-1/2" 3/16" 80 0.25
80079 2" 3/16" 80 0.38
--,-,.'r 80080 2-1/2" 1/4" 80 0.67
I-T/0 80081 3" 3/16" 80 0.91
80220 1"x 3/4" 1/8" 40 0.08
80200 1"x 3/4" 7/16" 40 0.04
80201 1-1/4"x 3/4" 1/2" 40 0.11
80202 1-1/4"x 1" 5/16" 40 0.12
80203 1-1/2"x 3/4" 5/8" 80 0.16
80204 1-1/2"x 1" 1/2" 80 0.14
REDUCER BUSHING 80205 1-1/2"x 1-1/4" 3/8" 80 0.17
80206 2"x 3/4" 13/16" 80 0.27
F
80207 2"x 1" 11/16" 80 0.26
80208 2"x 1-1/4" 9/16" 80 0.24
80209 2"x 1-1/2" 7/16" 80 0.19
-I T/O 80215 2-1/2"x 1" 15/16" 80 0.42
80214 2-1/2"x 1-1/4" 13/16" 80 0.45
80213 2-1/2"x 1-1/2" 11/16" 80 0.46
80211 2-1/2"x 2" 5/8" 80 0.29
80210 3"x 2" 3/4" 80 0.72
80212 3"x 2-1/2" 1/2" 80 0.47
CAP 80100 3/4" 5/16" 40 0.04
80101 1" 3/8" 40 0.06
e_c80102 1-1/4" 7/16" 40 0.10
80103 1-1/2" 11/16" 80 0.20
e,,r111_
I 80104 2" 5/8" 80 0.31
T/O- 80105 2-1/2" 7/8" 80 0.58
80106 3" 1" 80 0.88
GROOVED TIO PIPE O.D.
COUPLING ADAPTER
80160 1-1/4"x 1-1/4"Groove 2-5/16" 1-1/4" 1.660" 40 0.78
80161 1-1/2"x 1-1/2"Groove 2-5/16" 1-1/2"(1.900") 80 0.95
PIPE 80162 2"x 2"Groove 2-5/16" 2"(2.375") 80 1.42
O.D.
80163 2-1/2"x 2-1/2"Groove 2-5/16" 2-1/2"(2.875") 80 2.28
80164 3"x 3"Groove 2-1/4" 3"(3.500") 80 3.00
-T/0-I 80169 2-1/2"x 76,1 mm Groove 2-5/16" 76,1 mm(3.000") 80 2.28
FIGURE 2-FITTING DIMENSIONS(Part 2 of 4)
TFP1915 Page 5 of 6
FITTING PART NOMINAL SIZE NOMINAL TAKE-OUT SCHD. WEIGHT
TYPE NUMBER (I/O) (lb.)
SPRINKLER HEAD
ADAPTER
80175E 3/4"x 1/2"NPT 7/16" 80 0.20
80176E 1"x 1/2"NPT 7/16" 80 0.22
h"\\ 80175WL 3/4"x 1/2"NPT 7/16" 40 0.16
80179 1"x 3/4"NPT 13/16" 40 0.43
T/O
SPRINKLER HEAD
ADAPTER
t."x' 80175W 3/4"x 1/2"NPT 1/2" 40 0.19
80176W 1"x 1/2"NPT 1/2" 40 0.18
T/O
SPRINKLER HEAD
ADAPTER(SPIGOT)
_ 80177L 3/4"x 1/2"NPT 1/2" 40 0.16
11.111 80178 1"x 1/2"NPT 9/16" 40 0.20
�/o..= 80180 1"x 3/4"NPT 7/8" 40 0.40
—I T/O
FEMALE ADAPTER
,z/z/ `k1 80142 3/4"x 3/4"NPT 13/16" 40 0.41
80145 1'x 1"NPT 7/8" 40 0.63
80146 1-1/4"x 1-1/4"NPT 1-1/8" 40 1.03
�� 80147 1-1/2"x 1-1/2"NPT 1-3/8" 80 1.42
//// 80148 2"x2"NPT 1-11/16" 80 2.66
— —T/O
MALE ADAPTER
,„.....r,
_,
80157 3/4"x 3/4"NPT 1-5/16" 40 0.33
80158 1'x 1"NPT 1-3/8" 40 0.56
'7/7/
T/O
XxYxZ X Y Z
SPRINKLER HEAD 80250 3/4"x 3/4"x 1/2"NPT 9/16" 9/16" 1" 40 0.22
ADAPTER TEE
Z 80251 1"x 1"x 1/2"NPT 11/16" 11/16" 1-3/16" 40 0.29
;_=, T/O 80249 1"x 1"x 1"NPT 15/16" 15/16" 1-9/16" 40 0.73
I\ ��) 80256 1-1/4"x 1"x 1/2"NPT 7/16" 9/16" 1-5/16" 40 0.30
-Ill- 80252 1-1/4"x 1-1/4"x 1/2"NPT 7/16" 7/16" 1-5/16" 40 0.31
X -..- Y 80257 1-1/2"x 1-1/4"x 1/2"NPT 1/2" 11/16" 1-7/16" 80 0.43
80254 1-1/2"x 1-1/2"x 1/2"NPT 1/2" 1/2" 1-7/16" 80 0.46
T/O •• T/O 80258 2"x 1-1/2"x 1/2"NPT 1/2" 5/8" 1-11/16" 80 0.56
80253 2"x 2"x 1/2"NPT 1/2" 1/2" 1-11/16" 80 0.62
FIGURE 2—FITTING DIMENSIONS(Part 3 of 4)
Page 6 of 6 TFP191 S
FITTING PART NOMINAL SIZE NOMINAL TAKE-OUT WEIGHT
TYPE NUMBER (TIO) SCHD. (lb.)
BACK-TO-BACK TEE X x Y x Z X Y,Z
X
> >
i T/O
4
y
"�.4 80459 1"x 1/2"NPT x 1/2"NPT 5/8" 1-5/16" 40 0.48
�111 Z 1 80460 1"x 1/2"NPT x 1/2"NPT 5/8" 1-3/16" 40 0.46
T/0 T/0
BACK-TO-BACK CROSS X x Y x Z x W X,Y Z,W
• X
Ili T/O
IIIMWEWmfillII
11111Jan ini w 80462 1"x 1"x 1/2"NPT x 1/2"NPT 5/8" 1-3/16" 40 0.46
jt'=- 80463 1"x 1"x 1/2"NPT x 1/2"NPT 5/8" 1-5/16" 40 0.47
T/0 III
��
T/0 T/0
SPRINKLER HEAD X x Y X Y
ADAPTER 90°ELBOW
Y
,;'`l T/0
80199 3/4"x 1/2"NPT 9/16" 1" 40 0.20
1.0
Tii,
80198 1"x 1/2"NPT 3/4" 1-1/4" 40 0.26
-x I 80196 1"x 3/4"NPT 1-1/16" 1-7/16" 40 0.26
- -T/O
FIGURE 2—FITTING DIMENSIONS(Part 4 of 4)
Limited by TFBP to be defective shall be either of merchantability and fitness for a par-
repaired or replaced, at TFBP's sole ticular purpose.
Warranty option. TFBP neither assumes, nor authorizes any person to assume for it, This limited warranty sets forth the ex-
clusive remedy for claims based on
Products manufactured b T Fire& any other obligation in connection with failure of or defect in products, materi-
Y Y co the sale of products or parts of prod-
Building Products (TFBP) are war- ucts.TFBP shall not be responsible for als or components, whether the claim
ranted solely to the original Buyer for sprinkler system design errors or inac- is made in contract, tort, strict liability
or any other legal theory.
ten(10)years against defects in mate- curate or incomplete information sup-
rial and workmanship when paid for plied by Buyer or Buyer's repre- This warranty will apply to the full ex-
and properly installed and maintained sentatives. tent permitted by law.The invalidity, in
under normal use and service. This In no event shall TFBP be liable, in `whole or part, of any portion of this
warranty will expire ten (10) years warranty will not affect the remainder.
. from date of shipment by TFBP. No contract, tort, strict liability or under
warranty is given for products or com- any other legal theory, for incidental,
ponents manufactured by companies indirect,special or consequential dam-
not affiliated by ownership with TFBP ages, including but not limited to labor
or for products and components which charges, regardless of whether TFBP
have been subject to misuse,improper was informed about the possibility of
installation, corrosion, or which have such damages, and in no event shall
not been installed, maintained, modi- TFBP's liability exceed an amount
fied or repaired in accordance with ap- equal to the sales price.
plicable Standards of the National Fire The foregoing warranty is made in lieu
Protection Association, and/or the of any and all other warranties. ex-
standards of any other Authorities Dress or implied. including warrantiess,
Having Jurisdiction. Materials found
TYCO FIRE&BUILDING PRODUCTS,451 North Cannon Avenue,Lansdale,Pennsylvania 19446
Dimensions - Weights
4 A 1Wik
• m II No
1 1 I
Er._ ...A1 •-•
REM".:11.11E
111W11
aii MWIErin
101 B
- luirimiElla- -. 1U , "•"• -11=11.
0
illikipi'
1-1•91•MlIP
F '11N;....i........./A
-
Suffix HC- Fire Hydrant Fittings dimension"A"=231e(594mm) 4-H *-I--*
4 G *
SIZE(DN) DIMENSIOWS WEIGHT
A B C F G H I
in. mm in. mm in. mm in. mm in. mm in. mm in. mm in. mm lbs. kgs.
1/2 15 10 254 4% 117 27A6 62 5 127 3% 85 25A6 59 21A6 52 4.5 2
" % 20 111/4 282 4 102 3% 79 6%6 157 37/46 87 2% 54 13A6 33 5 2.3
1 25 131/4 337 5% 130 4 102 7% 191 3% 85 111/I6 43 111/16 43 12 54
1% 32 16% 416 5 127 35A6 84 91/4 241 5 127 . 3 76 2 50 15 6.8
1% 40 163/4 425 4% 124 31/4 89 9% 248 513A6 148 3% 79 21%6 68 15.86 7.2
2 50 191/4 495 61/4 159 4 102 13% 340 6% 156 3%6 87 21%6 68 25.75 11.7
Strainer sold separately
Capacities
kPa psi A l//4h1 (32mm)
As compiled from documented Foundation for Cross-Connection Control 96 14
and Hydraulic Research at the University of Southern California lab tests. 44) 83 12
. co
ATypical maximum system flow rate(7.5 feet/sec.,2.3 meters/sec.) 0 69 10
-i
, 55 8
V2" (15mm)
kPa psi t 41 6
Aca . ....._._....._.__..........."'"."'../......".""
01 83 12 ce 28 4 ,
0 69 10 O..1! 14 2
-i
55 8
0 0
1- 41 6 -- ._.-..-
...-.-,-"'"-
=
0 10 20 30 40 50 60 70 80 90 100 110 120 gpm
(a 28 4 AP
co 0 38 76 114 152 190 228 266 304 342 380 418 456 Ipm
e14 2
ii. 0 0 5 7.5 10 15 fps
1.5 2.3 3.0 4.6 mps
0 2 4 6 8 10 12 gpm
AP 0 7.6 15.2 22.8 30.4 38 45.6 Ipm Flow Rate
57.5 10 fps
1.5 2.3 3.0 mps kPa psi 11/2"(40mm)
Flow Rate 83 12
kPa psi (20mm) ce 69 10
3/
A 4"
152 22
355 8
co
cs
41 6
0 124 18
-J ... :_..................„........„0.7..../....„........"
2
3 28 4
;12 96 14
I 14 2
=
0
ro) 69 10 .- 0 0
O.
0 APO 10 20 30 40 50 60 70 80 90 100 110 120 gpm
41 6
0 38 76 114 152 190 228 266 304 342 380 418 456 Ipm
14 2 1.---"--
5 7.5 10 15 fps
0 5 10 15 A 25 30 35 40 45 50 gpm 1.5 2.3 3.0 4.6 mps
AP 0 19 33 9 % M 114 133 re 111 193Ipm Flow Rate
7.5 15 fps
2.3 4.6 mps kPa psi 2" (50mm)
Flow Rate 0 83 12 A
kPa psi
110 16 A 1"(25mm) co
0 69 10
-
2 -I
0 55 8
83 12
......0°
-J ii-) 41 6
0 69 10 3
- I 28 4 ..........
3 55 8
S 41 6 21 14 2
O.
2 28 4 0 0
O. 142 - 0 25 50 75 100 125 150 175 200 gpm
• AP 0 95 190 285 380 475 570 665 760 1pm
0 5 10 15 20 25 30 35 40 45 50 55 60 gpm 5 7.5 10 15 fPs
AP 0 19 38 57 76 95 114 133 152 171 190 209 2281pm 1.5 2.3 3.0 4.6 mps
5 7.5 10 15 fps Flow Rate
1.5 2.3 3.0 4.6 mps
AFlow Rate
AMES
FIRE&WATERWORKS'
A Watts Water Technologies Company USA:Backflow Tel:(978)689-6066•Fax:(978)975-8350•ArnesFireWater.com
USA:Control Valves Tel:(713)943-0688•Fax:(713)944-9445•AmesFireWater.com
Canada: Tel:(905)332-4090•Fax:(905)332-7068•AmesFireWater.ca
Latin America: Tel:(52)81-1001-8600•Fax:(52)81-8000-7091 •AmesFireWater.com
ES-A-2000B 1410 0 2014 Ames Fire&Waterworks
P POTTER FOR SMALL PIPE VSR-S
VANE TYPE WATERFLOW
a The Symbol of Protection ALARM SWITCH WITH RETARD
Fig. 1 Fig.2
i
Retard Adjustment DO NOT LEAVE COVER OFF FOR EXTENDED PERIOD OF TIME RAW '.'MM Areaox.
The time delay is factory set at 30±10 seconds. COVER TAMPER 5WITCH F--/
The delay can be adjusted by rotating the retard —3 jL
adjustment knob from 0 to the max setting(60- �S�-.0-„el..---Al
I D
j II
90 seconds).The time delay should beset at the �% Imo,
minimum required to prevent false alarms. .���� ___� __ w�
(64 ; {�'!
P POTTER FOR SMALL PIPE VSR-S
VANE TYPE WATERFLOW
a The Symbol of Protection ALARM SWITCH WITH RETARD
Testing Removal
The frequency of inspection and testing for the Model VSR-S and its • To prevent accidental water damage,all control valves should
associated protective monitoring system should be in accordance with be shut tight and the system completely drained before waterflow
applicable NFPA Codes and Standards and/or the authority having detectors are removed or replaced.
jurisdiction(manufacturer recommends quarterly or more frequently.) • Turn off electrical power to the detector,then disconnect wiring.
An inspector's test valve(usually located at the end ofthe most remotebranch • Use a wrench on the flats of the bushing.Turn the switch
line)should always be used for test purposes.If there are no provisions for counterclockwise to disengage the pipe threads.
testing the operation of the flow detection device on the system,application • Gently lift with your fingers,roll the vane so it will fit through the
of the VSR-S is not recommended or advisable. hole while continuing to lift the waterflow detector.
A minimum flow of 10 gpm(38 Lpm)is required to activate this device. • Lift detector clear of pipe.
NOTICE Please advise the person responsible for testing of the A CAUTION
fire protection system that this system must be tested in accordance with
the testing instructions. Waterflow switches that are monitoring wet pipe sprinkler systems
Maintenance shall not be used as the sole initiating device to discharge AFFF,
Inspect detectors monthly for leaks. If leaks are found, replace the deluge,or chemical suppression systems.Waterflow switches used
detector.The VSR-S waterflow switch should provide years of trouble- for this application may result in unintended discharges caused
free service.The retard and switch assembly are easily field replaceable. by surges,trapped air,or short retard times.
In the unlikely event that either component does not perform properly,
please order replacement retard switch assembly stock#1029030.There
is no maintenance required,only periodic testing and inspection.
Mounting Dimensions
3.50" 5.56"
A GROUND SCREWS (89.0 mm) (141.2 mm)
2.00"
et Nur i-J''moi
(50.8 mm)
1C11
II11:1I)
LI2.34,.
Ii.
(59.4 mm) III
• nTO
-M 4.89" - - - -i-IIIMMIIIIIME
FO�• Wi 52.3 mm
1"-11 1/2 NPT :1_
61 li
DWG#1206-5
PRINTED IN USA MFG.#5401206-REV G PAGE 3 OF 3
12/08
F
Arti Model 1000
A'
cous
TESTAN DRAIN®
APPROVED 300 PSI Bronze Ball Valve
MODEL 1000 - PLAN VIEW FRONT VIEW - HORIZONTAL INSTALL
A E�I 1
t
O F a�_O f I I��"NPT SYSTEM
I^fir ACCESS PORT
TO DRAIN ! . �I (/r�� • ■ TO DRAIN 1 / -*-- 15 _ ___j
C �� �� G `.i l 1 v •
O
DIMENSIONS MATERIALS
Orifice Size Available:3/s",7/16", 'h", 17/32", ELO(%")*, ESFR(3/4")* &K25** Handle:Steel
SIZE A B C D E F G H Stem: Rod Brass
Ball:C.P. Brass
33., 51/46" 11/2" 23/46" 35/8" 30" 1106" 406" 6W Body: Bronze
(128 mm) (37.5 mm) (57 mm) (93 mm) (86 mm) (46 mm) (117 mm) (162.5 mm) Valve Seat: Impregnated Teflon®
5146" 11/2" 23/46" 35/8" 30" 113/46" 40i6" 60" Indicator Plate:Steel
1 Handle Stop:Steel
(128 mm) (37.5 mm)
(57 mm) (93 mm) (86 mm) (46 mm) (117 mm) (162.5 mm)
11/4" 57/16" 111/16" 29/16" 41/4" 306" 110/46" 506" 51/2" APPROVALS
(163 mm) (43 mm) (65 mm) (108 mm) (83 mm) (51 mm) (141 mm) (192 mm)
UL and ULC Listed(EX4019)
11/2" 67/6" 1106" 31/4" 51/46" 3%' 20" 81/4" 107/8" FM Approved
(163 mm) (45 mm) (81.5 mm) (127 mm) (99 mm) (67 mm) (207 mm) (274 mm)
NYC-BSA No. 720-87-SM
2" 67/16" 113/16" 31/4" 51/16" 37/8" 25/8" 81/4" 107/8"
(163 mm) (45 mm) (81.5 mm) (127 mm) (99 mm) (67 mm) (207 mm) (274 mm) x;*,*
*Available on 11/a"to 2"size units only x;;*�
x�rx
**Available on 11/2"and 2"size units only *x
/ �
THE MODEL 1000 PROVIDES ALL OF THE FOLLOWING... MADE IN U.S.A.
From the 2007 Edition of NFPA 13
Chapter 8.16.2.4.1" Provisions shall be made to properly drain all parts of the system.
Chapter 8.16.2.4.2 Drain connections, interior sectional or floor control valve(s)-shall be provided with a drain
&8.16.2.4.3 connection having a minimum size as shown in Table 8.16.2.4.2.
Chapter 8.16.2.4.4 Drains shall discharge outside or to a drain capable of handling the flow of the drain.
Chapter A.8.17.4.2 (Wet Pipe System)test connection is permitted to terminate into a drain capable of accepting full
flow... using an approved sight test connection containing a smooth bore corrosion-resistant orifice
giving a flow equivalent to one sprinkler...
Chapter 8.17.4.2.2 The test connection valve shall be readily accessible.
Chapter 8.17.4.2.4 shall be permitted to be installed in any location...downstream of the waterflow alarm.
Chapter 8.17.4.3.1 (Dry Pipe System)a trip test connection not less than 1" in diameter,terminating in a smooth bore
corrosion-resistant orifice,to provide a flow equivalent to one sprinkler...
Chapter 8.17.4.3.2 The trip test connection...with a shutoff valve and plug not less than 1",at least one of which shall
be brass.
USA Patent # 4741361 and Other Patents Pending
AGF Manufacturing Inc. Job Name:
G 100 Quaker Lane,Malvern,PA 19355
Phone:610-240-4900 Architect:
FFax:610-240-4906 Engineer:
www.testandrain.com
Contractor:
Zgg.g§§)
P.O. Box 3365 South El Monte, CA 91733 626.444.0541 Fax 626.444.3887 www. Afcon.org
510
CPVC - COPPER - STEEL
HANGER
Fastener
12E CDim.
3/4 2.125
0 1 2.312
1 1/4 3.170
1 1/2 3.400
92 4.010
2 1/2 4.320
3 5.320
SIZE-SYSTEM PIPE: 3/4"thru 3"
MATERIAL-Carbon Steel.
FINISH-Mil.Galvanized.
LISTING/APPROVAL-
`0"203-EX 4231,EX 2551
FUNCTION-Support horizontal piping: CPVC,Copper or Steel.
Size 3/4"-2"Prevents upward movement of pipe from pendent sprinkler discharge.
Stabilize vertical piping.
INSTALLATION- Per these instructions { ig
including NFPA 13, 13R, 13D and CPVC manufacturers instructions. Q )
Install on horizontal or vertical mounting surface.
FASTENERS- UL Listed per NFPA 13
in WOOD:
3/4" -3"CPVC pipe-#905 screw-no pre-drill.
3/4" -3"Steel and Copper pipe-#14 x 1 1/2" SMS or
1/4"x11/2" lag bolt-no pre-drill. Restraint
in STEEL-min. 18 GA.
3/4"-3"CPVC,Copper and Steel pipe- 1/4"or#14 Tek Screw. 1
FEATURES
*Offset edge eliminates abrasion. or
*Retainer dimples secure hanger to pipe during installation.
*Required AFCON#905 screw included-5/16"hex head. Hanger '"SII
9 �w >. Stabilize
ORDERING-Part#and pipe size.
I 1
CAN ALSO BE USED TO REPLACE -#500 Pipe Strap
#520 Tin Strap
Specific AFCON products are exclusively designed to be compatible ONLY with other AFCON products including parts and fasteners,resulting in a listed sway brace,restrainer or hanger assembly.
Be advised the following warranty restriction will apply. DISCLAIMER-AFCON will NOT warrant against the failure of its products when used in combination with other products,parts or systems
not manufactured or sold by AFCON.AFCON shall NOT be liable under any circumstances whatsoever for any director indirect,incidental or consequential damages of any kind,including but not
limited to loss of business or profit,when non-AFCON products have been,or are used.
5/14 � t