Loading...
Report Railing Connectors - Installation Instructionso rs® Raccords de Rampe - Instructions d'installation Conectores para Barandal - Instrucciones de Instalacion For use with nominal 2x4 rails in the vertical position: 1. Measure the distance between two posts and subtract 1/2". Cut rails to this length. 2. Attach a connector to each end of the rail with two screws through the pre-drilled holes (fig. 1). Set the rail at the desired height and check to ensure it is level. Fasten with screws through the pre-drilled holes (fig. 2). 3. To ensure the connectors stay in place, apply a small amount of clear silicon on the screw being inserted into the connector. Pour utilisation avec une rampe de 2 po sur 4 po, installee a Ia verticale : 1. Mesurer Ia distance entre deux poteaux et en soustraire 1/2 po. Couper la rampe a la longueur voulue. 2. Fixer un connecteur a chaque extremite de Ia rampe a moyen de deux vis, en utilisant les trous preperces (fig.1). Placer la rampe ala hauteur souhaitee, puis s'assurer guide est bien de niveau. Fixer au moyen de vis, en utilisant les trous preperces (fig. 2). 3. Pour vous assurer que les connecteurs ne se deplacent pas, appliquer un peu de silicone transparent sur la vis avant de I'inserer dans le connecteur. Para su use con barandales de 2x4 en posicion vertical: 1. Mida la distancia entre dos postes y restele 1/2". Corte los barandales a esta longitud. 2. Coloque un conector a cada extremo del barandal usando los tornillos y las perforaciones ya taladradas (fig. 1). Ajuste el barandal a la altura deseada y verifique que este nivelado. Ajustelo en su lugar con los tornillos en las perforaciones ya taladradas (fig. 2). 3. Para asegurarse de que los conectores permanezcan en su lugar, aplique un poco de silicona transparente en el tornillo que vaya a insertar en el conector. I <I fig.2 www.deckorators.com The diagrams and instructions in this brochure are for illustration purposes only and are not meant to replace a licensed professional.Any construction or use of the product must be in accordance with all local zoning and/or building codes.The consumer assumes all risks and liability associated with the construction or use of this product.The consumer or contractor should take all necessary steps to ensure the safety of everyone involved in the project,including,but not limited to,wearing the appropriate safety equipment. EXCEPT AS CONTAINED IN THE WRITTEN LIMITED WARRANTY,THE WARRANTOR DOES NOT PROVIDE ANY OTHER WARRANTY,EITHER EXPRESS OR IMPLIED,AND SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING CONSEQUENTIAL DAMAGES. ©2012 Universal Forest Products,Inc.All rights reserved.Deckorators is a registered trademark of Universal Consumer Products,Inc.in the U.S. 4710 RC sheet_4/12 l ATI-ES Code Compliance Research Report CCRR-0161 Page 4 of 23 Table 1 Deckorators®Railing Systems Building Code Recognition Deckorators® Guardrail Baluster Style Code Aluminum Railing T Systems (1) Type Baluster Connector Recognition 32 in Classic Aluminum Classic Baluster Connector PN 104.3 PN 107.1,1072& 129.1,107.3 Stair 32 in Frontier Scenic Glass Nylon Baluster Connectors Level(2)& PN 116.1 PN 125.1 &126.1 72 in by 42 inIBC-All Use Stair 32 in Contour Scenic Glass Nylon Baluster Connectors 96 in by 42 in PN 124.1 PN 127.1 &128.1 Groups 32 in, Estate Aluminum Estate Baluster Connectors IRC PN 114.3 PN 108.1 &130.1 One-and 40 in Baroque Aluminum Face Mounted to Rails Two-Family PN 110.3 Dwellings 36in-Classic Aluminum Classic Baluster Connector 72 in by 46 in Level & PN 107.1,1072& 96 in by 46 in Stair PN 104.4 129.1,107.3 Stair 26 in Scenic Glass Nylon Baluster Connectors PN 123.1 PN 125.1 &PN 126.1 Stair 32 in Contour Scenic Glass PN 124.1 32 in Frontier Scenic glass PN 116.1 32 in Traditional Aluminum Face Mounted to Rails PN 111.2 IRC(only) 72 in by 36 in Level & 32.25 in Arc Aluminum One-and 96 in by 36 in Stair PN 112.2 Two-Family 32.25 in Baroque Aluminum Dwellings(3) 'PN 110.2 26 in Colonial Aluminum Classic Baluster Connector PN 113.1 PN 107.2 or 107.1 &107.3 or 26 in-Classic Aluminum 129.1 Stair PN 104.2 26"Estate Aluminum - Estate Baluster Connector PN 1142 PN 108.&PN 130.1 Stair 1 Guardrails are qualified up to and including the listed maximum guardrail system dimensions for use in the referenced Code Occupancy Classification. 2AII level systems included in Table 1 may use the 22.5' and 45° angle adapter under both IRC and IBC recognition. 3 The use of this product shall be limited to exterior or interior use as a guard system for balconies and porches for one- and two-family dwellings of Type V-B (IBC) construction and dwellings constructed in accordance with the IRC. Architectural Testing 130 Deny Court• York, PA 17406 717-764-7700 www.archtest.corn