Report (78) f '
111
STREET TREE
TIGARD
CERTIFICATION
•
agent or t u �L r
owner/
ag f
(PLEASE PRINT) (PERMIT HOLDER)
do hereby cert that the following location meets
City of Tigard land use and development standards
for street tree installation and is consistent
with the approved site plan.
PERMIT NO.: \O.—WI 1- c ' b p
SI1 B ADDRESS: 41 sy 47'2) t )
SUBDIVISION: „ & LOT#:
SIGNATURE: � - —_ DATE: l I-1
(OWNER/AGENT)
RECEIVED &
VERIFIED BY: / DATE: 30
(CITY OF TIGARD)
Tree location verified per approved site plan.
L\Building\Forms\StreetTreeCertificate 05/30/2012
."M
Building Airtightness Test Form
Customer Information: Brett Groves—503.481.3138
Name: Riverside Home Address: 17933 NW Evergreen Pkwy—Suite 370
City: Beaverton State/Zip: OR 97006
Phone: 503;645.0986 Email: bgroves@riversidehome.com
Building Address:(if different from above): Lot#4
Street: 12839 SW 133rd Ave City/State/Zip: Tigard,OR 97223
Building and Test Conditions:
Date: 08/29/2017 Time: 2:30 Atmospheric Conditions: Calm
Floor Area (ft2): 3,382 Volume (ft3): 28,747 Exterior Surface Area (ft2): 6,665
# Bedrooms: 5 #Occupants: 6 Wind Shielding: Low
BAS: 2,717 ACH@BAS: 5.7 BAS@70%: 1,902 ACH@70%: 4.0
Test#1 : Fan Model/SN: Minneapolis Blower Door
Depress: X Press_ Pre-test Baseline Press: -0.1 (Pa) Post-test Baseline Press:-0.2 (Pa)
Bdlg Press:(Pa) -50.0 Flow Ring Installed: A Fan Press:(Pa) 130 Flow:(cfm) 2,042
Results:
CFM50: 2,042 CFM50/ft2: 0.60% Mpls Leakage Ratio: 0.31%
Comments:
Test#2 : Fan Model/SN:
Depress: X Press_ Pre-test Baseline Press: (Pa) Post-test Baseline Press: (Pa)
Bdlg Press:(Pa) -50.0 Flow Ring Installed: Fan Press:(Pa) Flow:(cfm)
Results:
CFM50: ACH50: CFM50/ft2: Mpls Leakage Ratio:
(Pa):Pascal a pressure unit-(CFM):cubic feet per minute-(CFM50):cubic feet per minute at 50 Pascal
(ACH50):Air Changes per Hour at 50 Pascal - (BAS)Building Airflow Standard
(CFM50/ft2):%air leakage per square foot—(Mpls Leakage Ratio)—%air leakage per exterior surface
ASHRAE Standard 62.2,and is only appropriate for low-rise residential structures.
Recommended Whole Building Mechanical Ventilation Rate:This value is the recommended whole
building ventilation rate to be supplied on a continuous basis using a mechanical ventilation system.
The recommended mechanical ventilation rate is based on 7.5 CFM per person (or number of bedrooms
plus one—whichever is greater), plus 1 CFM per 100 square feet of floor area.This guideline assumes
that in addition to the mechanical ventilation, natural infiltration is providing 2 CFM per 100 square
feet of floor area.
ACH at 70%BAS or Below=Air Changes per Hour at 4.0 ACH or Below Installation of Mechanical Ventilation Strategy is
Required—
Wiliam McLaughlin: 17080 SW 17080 Place-King City,OR 97224
Cell:503.740.7147—E-mail:wsmclaughlin@msn.com—
BPI:5002849-PTCS:02890
•
.�1
Oregon Residential Specialty Code N1107.2
HIGH-EFFICIENCY INTERIOR LIGHTING SYSTEMS
Permit No.: owl- Jurisdiction:
Site Address: 1,L 'Yi � l � tvu
Subdivision/Lot#: 1 � � L, c
and/or
Map and Tax Lot#:
By my signature below, I certify that a minimum of fifty(50)percent of the permanently
installed lighting fixtures in the above mentioned building have been installed with compact or
linear fluorescent, or a lighting source that has a minimum efficacy of 40 lumens per input watt.
(Oregon Residential Specialty Code N1107.2)1
Signature: "`t Date: 30/
1'1
Owner/Gene'al ontractor/Authorized Agent
2 1 t
Print Name: L 7
ORSC Section N1107.2.High-efficiency interior lighting systems. A minimum of fifty(50)percent o the
permanently installed lighting fixtures shall be installed with compact or linear fluorescent,or a lighting source that
has a minimum efficacy of 40 lumens per input watt. Screw-in compact fluorescent lamps comply with this
requirement.
The building official shall be notified in writing at the fmal inspection that a minimum of fifty percent of the
permanently installed lighting fixtures are compact or linear fluorescent,or a minimum efficacy of 40 lumens per
input watt.
I:\Building\Forms\RES-HighEfficiencyLighting.doc 07/01/08
s
Oregon Residential Specialty Code R318.2
MOISTURE CONTENT ACKNOWLEDGEMENT FORM
I, \/ A "' v C ti LL) , am the general contractor or the owner-builder
at the following address:
Site Address: t-t,. co-7 t) 5,,v 1N-5 Yl! A -
City: - \ 7 ( t,
Permit#: 1-° 11
— u L uG•r s"
Subdivision/Lot#: a 9 i 4 4t C 1
and/or
Map and Tax Lot#:
To conform with the 2008 Oregon Residential Specialty Code(ORSC), Section R318.2 and
OAR 918-480-0140, I am notifying the building official that I am aware of the moisture content
Requirement of ORSC Section R318.2 and have taken steps to meet this code requirement.
[Section R318.2 is provided for reference].
R318.2 Moisture Content: Prior to the installation of interior finishes, the building
official shall be notified in writing by the general contractor that all moisture-sensitive
wood framing members used in construction have a moisture content of not more than 19
percent by dry weight of dry framing members. j
Signature: �-'' Date: �; �10 I til
General Contractor or Owner-Builder
I:\Building\Form\RES-MoistureSensitiveWood.doc 09/25/08