Loading...
Report • TFP500 Page 2 of 10 SPRINKLER ESCUTCHEON TEMPERATURE BULB SPRINKLER FINISH TYPE TYPE RATING COLOR CODE NATURAL CHROME POLYESTER* BRASS PLATED 135°F(57°C) Orange 155°F(68°C) Red 175°F(79°C) Yellow 1,2,3,4,5,6 1,2,4,5,6 STANDARD 200°F(93°C) Green 286°F(141°C) Blue 360°F(182°C) Mauve 1,2,3,6 1,2,6 135°F(57°C) Orange 155°F(68°C) Red 175°F(79°C) Yellow 1,2,3,5 1,2,5 RECESSED 200°F(93°C) Green 286°F(141°C) Blue 1,2 PENDENT 360°F(182°C) Mauve N/A (TY3255) 135°F(57°C) Orange 155°F(68°C) Red 175°F(79°C) Yellow DEEP 200°F(93°C) Green 286°F(141°C) Blue 360°F(182°C) Mauve 1,2,3,4,5 1,2,4,5 135°F(57°C) Orange 155°F(68°C) Red 175°F(79°C) Yellow WITHOUT 200°F(93°C) Green 286°F(141°C) Blue 360°F(182°C) Mauve 1,2,3 1,2 135°F(57°C) Orange 155°F(68°C) Red UPRIGHT WITHOUT 175°F(79°C) Yellow 1,2,3,4,5 1,2,4,5 (TY3155) 200°F(93°C) Green 286°F(141°C) Blue 360°F(182°C) Mauve 1,2,3 1,2 Notes: 1. Listed by Underwriters Laboratories,Inc.(UL),maximum order length of 48 inches 2. Listed by Underwriters Laboratories for use in Canada(C-UL),maximum order length of 48 inches 3. Approved by FM Global(FM Approvals),maximum order length of 48 inches 4. Loss Prevention Certification Board(LPCB)and CE conformity apply to these temperature ratings only 5. Approved by the City of New York under MEA 352-01-E 6. Approved by VdS Frame and deflector only N/A-Not Applicable TABLE A SERIES DS-1 PENDENT&UPRIGHT DRY-TYPE SPRINKLERS,5.6K,STANDARD RESPONSE LABORATORY LISTINGS AND APPROVALS TFP500 Page 3 of 10 SPRINKLER ESCUTCHEON TEMPERATURE BULB SPRINKLER FINISH TYPE TYPE RATING COLOR CODE NATURAL CHROME POLYESTER*** BRASS PLATED 135°F(57°C) Orange 155°F(68°C) Red 175°F(79°C) Yellow STANDARD 200°F(93°C) Green 286°F(141°C) Blue 360°F(182°C) Mauve 135°F(57°C) Orange 155°F(68°C) Red HSW* 175°F(79°C) Yellow 1** 2** 3*** 4,5 1**,2**,4,5 (TY3355) DEEP 200°F(93°C) Green 286°F(141°C) Blue 360°F(182°C) Mauve 135°F(57°C) Orange 155°F(68°C) Red 175°F(79°C) Yellow WITHOUT 200°F(93°C) Green 286°F(141°C) Blue 360°F(182°C) Mauve 1** 2**,5 1** 2** Notes: 1. Listed by Underwriters Laboratories,Inc.(UL),maximum order length of 48 inches 2. Listed by Underwriters Laboratories for use in Canada(C-UL),maximum order length of 48 inches 3. Approved by FM Global(FM Approvals),maximum order length of 48 inches 4. Loss Prevention Certification Board(LPCB)and CE conformity apply to these temperature ratings only 5. Approved by the City of New York under MEA 352-01-E * Horizontal sidewall with top of deflector-to-ceiling distance of 4 to 12 inches(100 to 300 mm) ** Light and ordinary hazard occupancies only *** Light hazard occupancies only ****Frame and deflector only TABLE B SERIES DS-1 HORIZONTAL SIDEWALL(HSW)DRY-TYPE SPRINKLER,5.6K,STANDARD RESPONSE LABORATORY LISTINGS AND APPROVALS PLUG WITH 017:101 INLET SEALING rill,ASSEMBLY i YOKE WRENCH SPRING ,71 111110 RECESS 4p-4��_ _ _(� INLET 1�.�.�., BAND1 isi ; jl,WATER 1 WRENCH z✓f TUBE k.'1114 1 CASING FLAT 1, 1 0 \.fir GUIDE 1� TUBE 1 = INSERT PUSH WRENCH ijiell � -1 IN TO ENSURE 1ENGAGEMENT `/.t BULB WITH SPRINKLER FRAME 1�, �l SEAT WRENCHING AREA [`( FIGURE 2 VENT HOLE ii1 .il 5 mm BULB W-TYPE 7 WRENCH ji DEFLECTOR N.' COMPRESSION SCREW FIGURE 1 SERIES DS-1 DRY-TYPE SPRINKLER, 5.6K, STANDARD RESPONSE ASSEMBLY TFP500 Page 4 of 10 SPRINKLER FITTING SPRINKLER FITTING SPRINKLER FITTING (REFER TO DESIGN (REFER TO DESIGN (REFER TO DESIGN CRITERIA SECTION) CRITERIA SECTION) CRITERIA SECTION) FACE OF FACE OF FACE OF SPRINKLER SPRINKLER SPRINKLER FITTING 1 , FITTING FITTING _ _J \ L _J \ L :1 ORDER LENGTHS: ( ORDER LENGTHS: ORDER LENGTHS: 3-1/2"DIA. 2-3/4"to 48" 1-3/4"DIA. 3-3/4"to 48" 1/2"to 46" (88,9 mm) (69,9 to 1219,2 mm) (44,5 mm) (95,3 to 1219,2 mm) (12,7 ) IN 1/4"(6,4 mm) IN 1/4"(6,4 mm) 2-1/4" DIA. IN,1/4to"(61168,4,4 mm)mm2-11/2" DIA. INCREMENTS .1 INCREMENTS (57,2 mm) INCREMENTS F(63,5 mm),.] mu , FACE OF — .�- CEILINGFACE O 1 I I / 1115FACE OF W CEILING Ili' I %Ai-MC,F ■r — CEILING I M Y —NO 4-1/4"±1/8" (108,0±3,2 mm) 2-3/16"±1/8" 3"DIA. 1-3/8"±1/8" 2-7/8"DIA. (55,6±3,2 mm) (76,2 mm) _ (34,9±3,2 mm) (73,0 mm)_ 1 �t��� FIGURE 4 FIGURE 3 PENDENT(TY3255) FIGURE 5 PENDENT(TY3255) WITH STANDARD PENDENT(TY3255) WITH STANDARD ESCUTCHEON RECESSED ESCUTCHEON WITH DEEP ESCUTCHEON SPRINKLER FITTING / (REFER TO DESIGN TOP OF CRITERIA SECTION) DEFLECTOR FACE OF SPRINKLER FITTING 1 \ L- -J ORDER LENGTHS: T 5"to 48" (127,0 to 1219,2 mm) ORDER LENGTHS: IN 1/4"(6,4 mm) 5"to 48" INCREMENTS (127,0 to 1219,2 mm) IN 1/4"(6,4 mm) INCREMENTS C SPRINKLEFAEOF R FITTING MINIMUM , 1-3/4"(44,5 mm) DEFLECTOR TO CEILING SPRINKLER FITTING (REFER TO DESIGN CRITERIA SECTION) FIGURE 6 FIGURE 7 PENDENT(TY3255) UPRIGHT(TY3155) WITHOUT ESCUTCHEON WITHOUT ESCUTCHEON TFP500 Page 5 of 10 ORDER LENGTHS: Operation 2-3/4"to 48"(69,9 to 1219,2 mm) IN 1/4"(6,4 mm)INCREMENTS When TYCO Series DS-1 5.6K Pendent, 2 3/8 ±1/8Upright,and Horizontal Sidewall,Stan- (60,3±3,2 mm) dard Response, g FACE OF FACE OF p se, Standard Coverage — SPRINKLER MOUNTING — Dry type Sprinklers are in service, FITTING SURFACE water is prevented from entering the c ' \ assembly by the Plug with Sealing Assembly(Ref. Figure 1) in the Inlet of 'IIIIIIIIIIIIIII' 11112 the sprinkler. } (76,2Dmm) The glass bulb contains a fluid that expands when exposed to heat.When \� 3.5° j the rated temperature is reached, the SPRINKLER FITTING 1-3/4"DIA. fluid expands sufficiently to shatter (REFER TO DESIGN (44,5 mm) CENTERLINE 5/16" the glass bulb, and the Bulb Seat is CRITERIA SECTION) OF WATERWAY (7,9 mm) released. FIGURE 8 The compressed Spring is then able HORIZONTAL SIDEWALL(TY3355) to expand and push the Water Tube as WITH STANDARD ESCUTCHEON well as the Guide Tube outward. This action simultaneously pulls inward on the Yoke, withdrawing the Plug with ORDER LENGTHS: Sealing Assembly from the Inlet,allow- 1/2"to 45-3/4"(12,7 to 1162,1 mm) ing the sprinkler to activate and flow IN 1/4"(6,4 mm)INCREMENTS water. 4-1/4"±1/8" 2-1/2" DIA. FACE OF (108,0±3,2 mm) Design FACE OF (63,5 mm) MOUNTING SPRINKLER SURFACE Criteria FITTING \ lima - TYCO Series DS-1 5.6K Pendent, 'IIIIIIIIIIIIi + Upright,and Horizontal Sidewall,Stan- dard Response, Standard Coverage I- J (88,9 mm) Dry-type Sprinklers are intended for -' ,, ink 3.5° use in fire sprinkler systems designed SPRINKLER FITTING \ in accordance with the standard instal- lation rules recognized by the applica- (REFERCRITERIA SECTION) OF WATERWAY (7,9 mm) ble listing or approval agency(e.g., UL Listing is based on NFPA 13 require- FIGURE 9 ments). For more information on LPCB HORIZONTAL SIDEWALL(TY3355) Approval, contact Tyco Fire Suppres- WITH DEEP ESCUTCHEON sion&Building Products at the follow- ing office: ORDER LENGTHS: Kopersteden 1 - 5-1/2"to 48"(139,7 to 1219,2 mm) 7547 TJ Enschede IN 1/4"(6,4 mm)INCREMENTS The Netherlands MINIMUM +31-(0)53-428-4444 Tel: 2-1/4"(57,2 mm) FACE OF DEFLECTOR TO Fax:+31-(0)53-428-3377 SPRINKLER MOUNTING Sprinkler Fittings FITTING SURFACE Install 1 inch NPT Series DS-1 Dry-type Sprinklers in the 1 inch NPT outlet or v :,.– 1 run of the following fittings: ----T-1- • malleable or ductile iron threaded ---/�}»•+..L • tee fittings that meet the dimen- 3.5° 5/16" sional requirements of ANSI B16.3 SPRINKLER FITTING (7,9 mm) (Class 150) (REFER TO DESIGN CENTERLINE • cast iron threaded tee fittings that CRITERIA SECTION) OF WATERWAY meet the dimensional requirements FIGURE 10 of ANSI B16.4(Class 125) HORIZONTAL SIDEWALL(TY3355) Do not install Series DS-1 Dry-type WITHOUT ESCUTCHEON Sprinklers into elbow fittings.The Inlet of the sprinkler can contact the interior of the elbow. The unused outlet of the threaded tee is plugged as shown in Figure 12. TFP5OO Page 6 of 10 Temperatures for Heated Area(1) Drainage In accordance with the minimum Ambient Temperature 40°F 50°F 60°F requirements of the National Fire Pro- Exposed to (4°C) (10°C) (16°C) tection Association for dry pipe sprin- Discharge End of Sprinkler Minimum Exposed Barrel Length(2), kler systems, branch, cross, and Inches feed main piping connected to Dry (mm) Sprinklers and subject to freezing 4o°F tem- peratures must be pitched for proper (4°C) 0 0 0 drainage. Exposure Length 30°F0 0 0 When using Dry Sprinklers in wet pipe (-1°C) sprinkler systems to protect areas 20°F 4 subject to freezing temperatures, use (-7°C) (100) 0 0 Table C to determine a sprinkler's 10°F 8 1 appropriate exposed barrel length to (-12°C) (200) (25) 0 prevent water from freezing in the con- necting pipes due to conduction. The 0°F 12 3 0 exposed barrel length measurement (-18°C) (305) (75) must be taken from the face of the 10°F 14 4 1 sprinkler fitting to the surface of the (-23°C) (355) (100) (25) structure or insulation that is exposed to the heated area. Refer to Figure 11 -20°F 14 6 3 for an example. (-29°C) (355) (150) (75) For protected area temperatures -30°F 16 8 4 between those given above, the (-34°C) (405) (200) (100) minimum recommended length from -40°F 18 8 4 the face of the fitting to the outside of (-40°C) (455) (200) (100) the protected area may be determined by interpolating between the indicated -50°F 20 10 6 values. (-46°C) (510) (255) (150) Clearance Space 60°F 20 10 6 (-51°C) (510) (255) (150) In accordance with Section 8.4.9.2 of the 2010 edition of NFPA 13,when con- Notes: necting an area subject to freezing and 1. For protected area temperatures that occur between values listed above,use the next cooler temperature. an area containin a wet pipe sprinkler 2. These lengths are inclusive of wind velocities up to 30 mph(18,6 kph). g p p p TABLE C system, the clearance space around EXPOSED SPRINKLER BARRELS IN WET PIPE SYSTEMS the sprinkler barrel of dry-type sprin- MINIMUM RECOMMENDED LENGTHS klers must be sealed. Due to tempera- ture differences between two areasreal,,the conden- You can also install Series DS-1 Dry- For dry pipe system installations, use potential for the formation of type Sprinklers in the 1 inch NPT outlet only the side outlet of maximum 2-1/2 sation in-tupup sprinkler and sIubsequent this con- of a GRINNELL Figure 730 Mechanical inch reducing tee when locating Series ice sation is iso increased.nicelled, this Tee and GRINNELL G-FIRE Figure 522; DS-1 Dry-type can sation is not might damabuild-up 9 y ype Sprinklers directly can occur that damage the dry- however,the use of the Figure 730 Tee below the branchline; otherwise, use type sprinkler and/or prevent proper and Figure 522 for this arrangement is the configuration shown in Figure 12 to operation in a fire situation. limited to wet pipe systems. assure complete water drainage from The configuration shown in Figure 13 above Series DS-1 Dry-type Sprin- Use of the Model DSB-2 Dry Sprinkler is only applicable for wet pipe systems klers and the branchline. Failure to do Boot,described in technical data sheet where the sprinkler fitting and water- so may result in pipe freezing and water TFP591 and shown in Figures 14 and filled pipe above the sprinkler fitting are damage. 15,can provide the recommended seal. not subject to freezing and where the length of the dry-type sprinkler has the NOTICE minimum exposure length depicted in Do not install Series DS-1 Dry-type Figure 11.Refer to the Exposure Length Sprinklers into any other type fitting section. without first consulting the Tyco Fire For wet pipe system installations of 1 Protection Products (TEPP) Technical inch NPT Series DS-1 Dry-Type Sprin- Services.Failure to use the appropriate klers connected to CPVC piping, use fitting may result in one of the following: only the following TYCO CPVC fittings: • failure of the sprinkler to operate • 1" x 1" NPT Female Adapter (P/N properly due to formation of ice 80145) over the Inlet Plug or binding of the Inlet Plug • 1" x 1" x 1" NPT Sprinkler Head Adapter Tee(P/N 80249) • insufficient engagement of the Inlet pipe-threads with consequent leakage TFP500 Page 7 of 10 11 RUN FACE OF i OUTLET , !2)1TO WET SIDE SPRINKLER _ PLUGGED SYSTEM OUTLET FITTING 7,_ i f\SPRINKLER PLUGGED FITTING HEATEDETO DRY HEATED AREA LENGTHE SYSTEM (SEE DESIGN AREA5,. (SEE DESIGN CRITERSECTION)IA DSB-2 CRITERIA AREA SPRINKLER DSB-2 INTENDED SECTION) SUBJECT DSB-2 INTENDED FITTING FOR FREEZER TO INTENDED FOR FREEZER (SEE DESIGN STRUCTURES FREEZING in FOR FREEZER STRUCTURES CRITERIA STRUCTURES SECTION) , zzAM,7 ::7 , 4. ail TAS -...0 FIGURE 12 FIGURE 13 FIGURE 11 SPRINKLER FITTING SPRINKLER FITTING EXPOSURE LENGTH UNHEATED AREA HEATED AREA STRAP TIES 1-3/4"DIA. 4. (ENDS ON (44,5 mm) OPPOSING CLEARANCE INSULATED SIDES OF HOLE FREEZER BOOT) ADHESIVE STRUCTURE DSB-2 BOOT DSB-2 ADHESIVE BOOT l 1-3/4" DIA. I IW. Ill �� (44,5 mm) Ti \ 111 lily FIN CLEAHOLERANCE 4iNAp___l_ i FREEZER - J STRUCTURE STRAP TIES •MINi DS-1 (ENDS ON DS-1 fin SHOWN WITH OPPOSING SHOWN WITH ,w/ STANDARD STANDARD SIDES OF ESCUTCHEON ESCUTCHEON BOOT) FIGURE 14 FIGURE 15 MODEL DSB-2 DRY SPRINKLER MODEL DSB-2 DRY SPRINKLER BOOT WITH PENDENT SERIES BOOT WITH SIDEWALL SERIES DS-1 DRY-TYPE SPRINKLER DS-1 DRY-TYPE SPRINKLER TFP5OO Page 8 of 10 Installation Note: If sprinkler removal becomes have not operated,should be replaced necessary, remove the sprinkler using if they cannot be completely cleaned TYCO Series DS-1 5.6K Pendent, the same wrenching method noted by wiping the sprinkler with a cloth or Upright,and Horizontal Sidewall,Stan above.Sprinkler removal is easier when by brushing it with a soft bristle brush. a non-hardening sealant was used dard Response, Standard Coverage Care must be exercised to avoid and torque guidelines were followed. Dry-type Sprinklers must be installed After removal,inspect the sprinkler for damage to the sprinklers before, in accordance with this section. damage. during, and after installation. Sprin- General Instructions klers damaged by dropping, striking, DS 1 Sprinklers must Step 3. After installing the ceiling or wrench twist/slippage,or the like,must Series be Sin1 Dry-type in Spthat meet wall and applying a ceiling finish, slide be replaced. Also, replace any sprin- only requirementsd inofittingsthe Design Crite- on the outer piece of the escutch- kler that has a cracked bulb or that has tthe section.Refer to the Desig Criteria eon until it comes in contact with the lost liquid from its bulb (Ref. Installa- n ase section for othert theimpDesign nt require- ceiling/wall. Do not lift the ceiling panel tion section). ments regarding piping design and out of its normal position. The owner is responsible for the sealing of the clearance space around When using the Deep Escutcheon, inspection,testing,and maintenance of the Sprinkler Casing. hold the outer piece in contact with the their fire protection system and devices not any bulb type sprinkler mounting surface(ceiling or wall).Then in compliance with this document, as if Do the installcracked lbothereeis a rotate the inner piece approximately 1/4 well as with the applicable standards if e bulb is cracked bulb.With is a lossinturn with respect to the outer piece, of the National Fire Protection Asso- of liquid r held fromhohe bully,a small air bubble to hold the Deep Escutcheon firmly ciation (e.g., NFPA 25), in addition to should be present.The diameter of the together. the standards of any other authorities air bubble is approximately 1/16 inch having jurisdiction.Contact the install- (1,6 mm)for the 135°F (57°C) rating to Care and ing contractor or product manufacturer 1/8 inch(3,2 mm)for the 360°F(182°C) with any questions. rating. Maintenance Automatic sprinkler systems are rec- ommendedObtain a leakti ht 1 inch NPT sprinkler to be inspected, tested, 9 P TYCO Series DS-1 5.6K Pendent, and maintained by a qualified Inspec- joint by applying a minimum-to-maxi- Upright, and Horizontal Sidewall, tion Service in accordance with local mum torque of 20 to 30 lbs.-ft.(26,8 to Standard Response, Standard Cover- requirements and/or national codes. 40,2 Nm). Higher levels of torque may age Dry-type Sprinklers must be main- distort the sprinkler Inlet with conse- tained and serviced in accordance with quent leakage or impairment of the this section. sprinkler. Before closing a fire protection system Do not attempt to compensate for main control valve for maintenance insufficient adjustment in an Escutch- work on the fire protection system eon Plate by under or over-tightening that it controls, obtain permission to the Sprinkler. Re-adjust the position of shut down the affected fire protection the sprinkler fitting to suit. systems from the proper authorities Notes: and notify all personnel who may be • Install pendent sprinklers only in affected by this action. the pendent position;install upright Absence of the outer piece of an sprinklers only in the upright posi- escutcheon, which is used to cover a tion. The deflector of a pendent or clearance hole, may delay the time to upright sprinkler is to be parallel to sprinkler operation in a fire situation. the ceiling. A Vent Hole is provided in the Bulb • Install horizontal sidewall sprinklers Seat(Ref.Figure 1)to indicate if the Dry in the horizontal position with their Sprinkler is remaining dry. Evidence of centerline of waterway perpendicu- leakage from the Vent Hole indicates lar to the back wall and parallel to potential leakage past the Inlet seal the ceiling. Ensure the word "TOP" and the need to remove the sprinkler on the Deflector faces the ceiling. to determine the cause of leakage; Step 1. With a non-hardening pipe- for example, an improper installation thread sealant such as TEFLON applied or an ice plug. Close the fire protec- to the inlet threads, hand-tighten the tion system control valve and drain the sprinkler into the sprinkler fitting. system before removing the sprinkler. Step 2. Wrench-tighten the sprinkler Sprinklers which are found to be using either: leaking or exhibiting visible signs of • a pipe wrench on the Inlet Band or corrosion must be replaced. the Casing(Ref. Figure 1) Automatic sprinklers must never be the W-Type 7 Sprinkler Wrench on painted, plated, coated, or other- • the WrenchFlat(Ref. Figure n wise altered after leaving the factory. Modified sprinklers must be replaced. Apply the wrench recess of the W-Type Sprinklers that have been exposed to 7 Sprinkler Wrench to the wrench flat. corrosive products of combustion,but TFP500 Page 9 of 10 P/N* 60 - XXX - X - XXX SIN SPRINKLER ESCUTCHEON FINISH FINISHI1) 96 Pendent with TY3255 SIGNAL WHITE Standard Escutcheon(1"NPT) (Figure 3) 0 CHROME (RAL9003) PLATED POLYESTER 93 Pendent with TY3255 Deep Escutcheon(1" NPT) (Figure 5) SIGNAL WHITE NATURAL 97 Pendent with TY3255 1 BRASS (RAL9003) OLYESTE Recessed Escutcheon(1"NPT) (Figure 4) 92 Pendent without TY3255 2 NATURAL BRASS Escutcheon(1" NPT) (Figure 6) BRASS PLATED Sidewall with TY3355 SIGNAL WHITE SIGNAL WHITE 94 AL9003) Standard Escutcheon(1"NPT) (Figure 8) 4 (RAL9003) O POLYESTER 53 Sidewall with TY3355 CHROME CHROME Deep Escutcheon(1"NPT) (Figure 9) 9 PLATED PLATED 54 Sidewall without TY3355 Escutcheon(1" NPT) (Figure 10) I TEMPERATURE ORDER Upright without TY3155 RATING(2) LENGTH(3) 98 Escutcheon1" NPT)) (Figure 7) 0 135°F(57°C) 055 5.50" Notes: 1 155°F(68°C) 082 8.25" 1. Escutcheon Finish applies to sprinklers provided with escutcheons. 2. 360°F(182°C)temperature rating applies to non-recessed sprinkler assemblies. 2 175°F(79°C) 180 18.00" 3. Dry-type Sprinklers are furnished based upon"Order Length"as mea- sured per Figures 3 through 10,as applicable,and for each individual 3 200°F93°C 187 18.75" sprinkler where it is to be installed.After the measurement is taken, ( ) round it to the nearest 1/4 inch increment. * Use Prefix"I"for ISO 7-R 1 Connection(e.g.,1-60-961-1-180). 4 286°F(141°C) 372 37.25" 5 360°F(182°C) 480 48.00" TABLE D SERIES DS-1 DRY-TYPE SPRINKLERS,5.6K, STANDARD RESPONSE PART NUMBER SELECTION Limited • SIN: • P/N from Table D TY3255-Pendent Part numbers are for 1 inch NPT Warrant TY3155- Upright standard order sprinklers. Orders Y TY3355-Horizontal Sidewall for all other sprinkler assemblies For warranty terms and conditions,visit • Order Length: must be accompanied by a complete www.tyco-fire.com. Dry-type Sprinklers are furnished description. based upon Order Length as mea- Sprinkler Wrench Ordering sured per Figures 3 through 10, as Specify W-Type 7 Sprinkler Wrench, applicable.After the measurement is P/N 56-850-4-001 Procedure taken,round it to the nearest 1/4 inch Sprinkler Boot increment. Specify Model DSB-2 Dry Sprinkler Contact your local distributor for avail- • Inlet Connections: Boot, P/N 63-000-0-002 ability. When placing an order, indi- 1 Inch NPT cate the full product name, including (Standard) This part number includes one(1)Boot, description and part number(P/N). two(2)Strap Ties,and 1/3 oz.of Adhe- ISODry-type Sprinklers 7-R 1 sive (a sufficient quantity for installing (For information on ISO Inlet Thread one boot). When ordering Series DS-1 5.6K Connections, contact your Tyco Pendent,Upright,and Horizontal Side- Sales Representative.) wall, Standard Response, Standard • Temperature Rating Coverage Dry-type Sprinklers,specify the following information: • Sprinkler Finish • Escutcheon Type and Finish, as applicable TFP500 Page 10 of 10 GLOBAL HEADQUARTERS 11400 Pennbrook Parkway,Lansdale,PA 19446 I Telephone+1-215-362-0700 Copyright©2015 Tyco Fire Products,LP. All rights reserved. tqco TEFLON is trademark of the DuPont Corporation. Fire Protection Products