Loading...
Specifications Michael K. Brown,S.E. 5346 E. Branchwood Dr. Boise,ID 83716 208-850-7542 mikebrown.se@gmail.com Job Name: Lot 34, South View By: MKB Core Job Number: DM15-169 Date: Dec., 2015 Code Basis of Design: Latest Adopted Version of O.S.S.C. and O.R.S.C. Wind Loading: Either ASCE 7 or O.S.S.0 projected area method allowed. ASCE 7-05 used. Wind: 120 MPH ult. Wind speed, Exposure B, 8:12 Pitch roof Side to Side and 4:12 Pitch Front to Back. Per ASCE 7 Figure 28.6-1: Front to Back: Zone A: 30.1 PSF Zone B: 0 Zone C: 20.9 Zone D: 0 For Zones A and B, a=10% of least horizontal dimension or 0.4h (h=mean roof height), but not less than 3'. Least horizontal dimension = 48 feet Therefore, use a = 4.8 feet Side to Side Zone A: 25.7 PSF Zone B: 17.6 Zone C: 20.4 Zone D: 14 For Zones A and B, a=10% of least horizontal dimension or 0.4h (h=mean roof height), but not less than 3'. Least horizontal dimension = 40 feet Therefore, use a = 4 feet Upper Floor: Front to Back: Average force on projected wall = (total force at zone A + total force at zone C)/overall length: 22.7 PSF Average force on projected roof = (total force at zone B + total force at zone D)overall length: 0 PSF Wall Plate Height = 8 feet Projected Average Roof Height = 6 feet Total Wind Force at Upper Level = 4366 #, or 91 PLF Michael K. Brown,S.E. 5346 E. Branchwood Dr. Boise,ID 83716 208-850-7542 mikebrown.se@gmail.com Job Name: Lot 34, South View By: MKB Core Job Number: DM15-169 Date: Dec., 2015 Side to Side: Horizontal Dimension = 40 Feet Average force on projected wall = 21.5 PSF Average force on projected roof= 14.72 PSF Projected Average Roof height = 6 Feet Total Wind Force at Upper Level = 6966 #, or 174 PLF Mail Level: Plate height = 9 Feet Front to Back: Average force on projected wall = 22.7 PSF Projected Length = 48 Feet Total Wind force at Main Level = 10369 #, or 216 PLF Total Wind force Upper and Main = 14736 # Side to Side: Averag force on projected wall = 21.5 PSF Projected Length = 40 Feet Total Wind force at Main Level = 8155 #, or 204 PLF Total overall side to side wind force = 15121 Pounds Seismic Loading: D1 seismic design category per O.R.S.C. SEs= .83, R = 6.5, W = weight of structure V = [1.2 SES/R] W V = .154W Roof Dead Load = 15 psf Floor Dead Load = 12 psf Int. wall Dead Load = 6 psf Ext. wall Dead Load = 12 psf Seismic Front to Back: Tributary Roof Length = 38 Feet Tributary Floor Length = 38 Feet Equiv. Trib Int wall Length = 10 Feet Trib. Ext upper wall Height = 4 Feet Trib. Ext lower wall Height = 4.5 Feet Michael K. Brown,S.E. 5346 E. Branchwood Dr. Boise,ID 83716 208-850-7542 mikebrown.se@gmail.com Job Name: Lot 34, South View By: MKB Core Job Number: DM15-169 Date: Dec., 2015 Wroof= 113.652 plf > 91 plf, therefore Seimsmic Gov. Wfloor = 125.202 plf < 216 plf, therefore Wind Gov. Total Seismic Load = 11464.99 Pounds < 14736 Therefore Wind Gov. overall Seismic Side to Side: Tributary Roof Length = 48 Feet Tributary Floor Length = 48 Feet Equiv. Trib Int wall Length = 10 Feet Trib. Ext upper wall Height = 4 Feet Trib. Ext lower wall Height = 4.5 Feet Wroof= 144.144 plf < 174 plf, therefore wind gov. Wfloor = 138.6 plf < 204 plf, therefore wind gov. Total Seismic Force = 10744.27 Pounds, < 15121 Pounds, therefore wind gov. overall Redundancy factor = 1.0 per ASCE 7, section 12.3.4.2 Roof Level Wall Lines: Line A: P = 114 * 24 ft = 2728 # Total Shear Wall Length = 14 Feet V=P/L = 195 PLF Use A wall Wall Height = 8 Feet Trib Roof Area = 2 Feet Shortest Wall Length 7 Feet Trib Floor Area = 0 Feet Mot = 7637 LB FT Factored Dead Load 76 PLF Mr = 1852 LB FT T = 826 LB No Uplift Line B: P = 114 * 24 ft = 2728 # Total Shear Wall Length = 17 Feet V=P/L = 160 PLF Use A wall Wall Height = 8 Feet Trib Roof Area = 2 Feet Shortest Wall Length 7 Feet Trib Floor Area = 0 Feet Mot = 6290 LB FT Factored Dead Load 76 PLF Mr = 1852 LB FT T = 634 LB No Uplift Michael K. Brown,S.E. 5346 E. Branchwood Dr. Boise,ID 83716 208-850-7542 mikebrown.se@gmail.com Job Name: Lot 34, South View By: MKB Core Job Number: DM15-169 Date: Dec., 2015 Line 1: P = 174 * 20 ft = 3483 # Total Shear Wall Length = 19 Feet V=P/L = 183 PLF Use A wall Wall Height = 8 Feet Trib Roof Area = 16 Feet Shortest Wall Length 19 Feet Trib Floor Area = 0 Feet Mot = 16719 LB FT Factored Dead Load 202 PLF Mr = 36389 LB FT T = -1035 LB No Uplift Line 2: P = 174 * 20 ft = 3483 # Total Shear Wall Length = 15 Feet V=P/L = 232 PLF Use A wall Wall Height = 8 Feet Trib Roof Area = 16 Shortest Wall Length 3.5 Feet Trib Floor Area = 0 Mot = 3901 LB FT Factored Dead Load 202 PLF Mr = 1235 LB FT T = 762 LB No Uplift Main Floor Wall Line: Front to Back: Line A: P = 216 * 24 ft + 2183 = 7367.76 # Total Shear Wall Length = 14 Feet V=P/L = 526 PLF Use B wall Wall Height = 9 Feet Trib Roof Area = 2 Feet Shortest Wall Length 7 Feet Trib Floor Area = 2 Feet Mot = 19893 LB FT Factored Dead Load 97 PLF Mr = 2381 LB FT T = 2502 LB Use type 1 HD Line B: P = 216 * 24 ft + 2183 = 7367.76 # Total Shear Wall Length = 22 Feet V=P/L = 335 PLF Use A wall Michael K. Brown,S.E. 5346 E. Branchwood Dr. Boise, ID 83716 208-850-7542 mikebrown.se@gmail.com Job Name: Lot 34, South View By: MKB Core Job Number: DM15-169 Date: Dec., 2015 Wall Height = 9 Feet Trib Roof Area = 2 Feet Shortest Wall Length 22 Feet Trib Floor Area = 2 Feet Mot = 39786 LB FT Factored Dead Load 97 PLF Mr = 23522 LB FT T = 739 LB No Uplift Side to Side: Line 1: P = 204 * 20 ft + 3483 = 7561 # Total Shear Wall Length = 27 Feet V=P/L = 280 PLF Use A wall Wall Height = 9 Feet Trib Roof Area = 16 Feet Shortest Wall Length 27 Feet Trib Floor Area = 7.5 Feet Mot = 40827 LB FT Factored Dead Load 263 PLF Mr = 95791 LB FT T = -2036 LB No Uplift Line 2: P = 204 * 20 ft + 3483 = 7561 # Total Shear Wall Length = 16 Feet V=P/L = 473 PLF Use B wall Wall Height = 9 Feet Trib Roof Area = 16 Feet Shortest Wall Length 3 Feet Trib Floor Area = 10 Feet Mot = 7655 LB FT Factored Dead Load 281 PLF Mr = 1264 LB FT T = 2131 LB Use Type 5 HD Lower Floor Wall Line: Line A: P = 216 * 24 ft + 3684 = 8869 # Total Shear Wall Length = 24 Feet V=P/L = 370 PLF Use B wall Wall Height = 9 Feet Trib Roof Area = 2 Feet Shortest Wall Length 24 Feet Trib Floor Area = 4 Feet Mot = 47890 LB FT Factored Dead Load 112 PLF Mr = 32141 LB FT T = 656 LB No Uplift Michael K. Brown,S.E. 5346 E. Branchwood Dr. Boise,ID 83716 208-850-7542 mikebrown.se@gmail.com Job Name: Lot 34, South View By: MKB Core Job Number: DM15-169 Date: Dec., 2015 Line B: Not Used. All loads to behind garage and shown on level above Side to Side : Line 1.2: P = 216 * 16 ft + 0 = 3456 # Total Shear Wall Length = 30 Feet V=P/L = 115 PLF Use A wall Wall Height = 9 Feet Trib Roof Area = 0 Feet Shortest Wall Length 30 Feet Trib Floor Area = 2 Feet Mot = 18665 LB FT Factored Dead Load 79 PLF Mr = 35640 LB FT T = -566 LB No Uplift Line 2: P = 216 * 18 ft + 7561 = 11449 # Total Shear Wall Length = 11 Feet V=P/L = 1041 PLF Use F wall Wall Height = 9 Feet Trib Roof Area = 16 Feet Shortest Wall Length 2 Feet Trib Floor Area = 18 Feet Mot = 11241 LB FT Factored Dead Load 338 PLF Mr = 677 LB FT T = 5282 LB Use type 3 HD O O 0AU O e IV e UV e rp 71 "il . _ .. II e II e cp-e e ® . 0 s r SE[U[1 412153[SR RLL CANTILEVER BASEMENT Q A e RETAINING WALLS. `V„ 0 VP ilik VP n IT AL Mir II L2 _ i_ L I —pe- up er YP d e6e eSe . eSM..G.i.iUWALLe e e I W/Si622d III Lin LOWER FLOOR PLAN MAIN FLOOR PLAN UPPER FLOOR PLAN SCALE:I/9=1' SCALE:1/6'=1' SCALE:i/9'=I' It.iallitantilinitiVirittitiariiiiiimiriAnsiorEllil1/3IYtI11111111111hlINIllil tillfIII11111 hintl11111]11111 l iii EMCEE 111ii111Ai1111111111111111111€1)11EIllallit1fh itl M AIC . f111111111114111t11111111.11111711111;11111 NMI 111lti 11111111111111'111it:1i1111iit11i1111t 11 I.hilt1i 11 111111Iiii}i ftl� IhiltEflilit€1IIIIIAIIilI1I111311111111111I1111i1lililifilil€11111111111111111111111111111111E1/111t1U Y1 11k1t1t 11111 llu 1fIt1/II ,,,� 11i11111i11111huffli1ih1111111111:11111 tilitl111113fiUit111ltE1f11E111111i1911E11111i111111[111i 11111lltti�1I11i11 f - ^,..,, Mr^'�'�'^ ..III!1111111111£illlEitilitI1IM€t11911NI/[i1ilAlitliiiitlEltt Il11t1iillt1ll tEll til111tt1i1t4R1111111Ml1illitill 114 ..... `N �,Z111 .,rte. `: fj f M�1LL Imn ([ Mmo M,MMR : ...MIMYIIIMM —__ is� 4 -1 11111MIMMMAM 1_ f MINIMMOW e tYS.-11.11111[....._¢.... -- ... [ -I -• .: .i 1 ... ..�` I ..z.,ax i .I.f�J011111 MMM �•--''�Y ,IIr/ ., '. 1,. ammo .Hltiili 1�F1wv3t. 114fI'tit 12112:114lI E li 1%i111I 111111 1111 Y lllliiii MIN lull 1111 1111 YY''sea th ,. 1111111 111 1al y IIY 1NICERI I1 ' '..I I� 1 r1i 811!1111 At��> 1 ' 1131 111111 €i 13111 11 t 1 7j [f(£11E rA 11 '"11fN i 1131H 11� A IH - ' '�"1e 11 ( li f€ ;::!� 1 � V €€it [EEtt111 �E€ �i"II..,, 11 1-IIE1 i� w.>r Ma. :O. 7�� i�M _ € 1�3 € _ i1 _.. s"� , II 111 1111 II II ll lin.= —.=.1I � 11.1.111.111Mff(1) 4 11II tili11 1t 11t 111111 11111 MEM I1Iii ..----1 E1 we 9 ,, t ��LI'1 :OOO�C�.00O Iii NE ®® �.�... ...._..._........ .�_,.,._. . : �., ....,. ,. r+ ,,,,,,G ,e00000 ooa .W 1 V SHEARWALL SCHEDULE _m (a ) MARK REF NOTES: (a,i) Note: (b) EDGE NAILING FEILD NAILING SILL TO CONCRETE SILL TO WOOD SHEAR TRNASFER Lbs NUMBER SHEATHING NAIL SIZE SPACING SPACING CONNECTION. Note: (c) CONNECTION. Note (g) CLIPS (h) CAPACITY • A 16" OSB (1) SIDE 8d 6" 12" 2" Dia. A.B. @ 48" o/c 16d @ 6" o/c A35 @ 18" o/c 384 B 16" OSB (1) SIDE (f) 8d 4" 12" 2"Dia. A.B. @ 24" o/c 16d @ 4" o/c A35 @ 14" o/c 560 C 16" OSB (1) SIDE (e,f) 8d 3" 12" 2" Dia. A.B. @ 18" o/c (m) 16d @ 3" o/c A35 @ 11" o/c 720 D 16" OSB (1) SIDE (e,f) 8d 2" 12" 2" Dia. A.B. @ 16" o/c (m) 16d @ 2" o/c A35 @ 8" o/c 936 E 16" OSB (2) SIDE (d,e,f) 8d 6" 12" 2" Dia. A.B. @ 18" o/c (m) 16d @ 3" o/c A35 @ 10" o/c 768 F 16" OSB (2) SIDE (d,e,f) 8d 4" Staggered 12" 2"Dia. A.B. @ 12" o/c (m) 16d @ 2" o/c A35 @ 7" o/c 1120 G 16" OSB (2) SIDE (d,e,f) 8d 3" Staggered 12" 2" Dia. A.B. @ 10" o/c (m) 16d @ 3" o/c(2)rows staggered A35 @ 5" o/c 1440 H 16" OSB (2) SIDE (d,e,f) 8d 2" Staggered 12" 2" Dia. A.B. @ 8" o/c (m) 16d @ 2" o/c(2)rows staggered HGA10KT @ 7" o/c 1872 Notes: a) Wood structural panels shall conform to the requireents for its type in DOC PS 1 or PS 2. All wall construction to conform to AF&PA SDPWS per IBC 2306.3. b) Use Common Wire Nails for all wood sheathing and cooler nails for gypboard sheathing. c) A.B. minimum 7" embed into concrete. 3"x3"x%" plate washers req'd at all shear wall A.B. Locate edge of Washer no greater than 2" from sheathed edge of sill plate. d) Panel joints shall be offset to fall on different framing members or framing shall be 3x or thicker and nails on each side shall be staggered. e) 3x or Dbl 2x framing at all panel edges and nails shall be staggered. f) All edges blocked. g) Common Wire Nails. h) Clip to be attached from continuous blocking to top of continuous top plates. Clips are not required at Gyp Bd walls but blocking is attached per the toenailing schedule. i) See attached typical shearwall details. j) Sheathing to be Structrual I Sheathing. k) Values are for framing of H-F. m) See plan for walls where seismic design shear is greater than 560 plf. 3x or 2x flat blkg at panel edges, Stagger nails. Where indicated on the plans 3x sills are required with A.B. spacing as per plan and schedule. See note C for plate washers req'd at A.B. For walls with the larger sills, Anchor Bolt spacing may be increased by a factor of 1.25 from the table above due to thicker sills. - , HOLDOWN SCHEDULE MARK Boundary Tension of DF Tension of HF Anchor Anchor NUMBER HOLDOWN Studs Allowable Lbs Allowable Lbs Mono Pour Two Pour • 1 HDU2-SDS2.5 OR PHD2-SDS3 (2)2x 3075 2215 SSTB14 SSTB2OL 2 HDU4-SDS2.5 OR (2)2x 4545 3270 SSTB16L SSTB2OL PHD5-SDS3 3 HDU8-SDS2.5 (3)2x 7870 5665 SSTB28L 7/ EDI MIN EMBED INNTOTO CON C. A36 THREADED ROD w/HEAVY SQ. NUT AND BP7/8-2 BEARING PLATE WASHER @ BOTT. 4 HDU11 -SDS2.5 (1)6x 9535 6865 1"DIA.x42"A36 1"DIA.x42"A36 THREADED ROD w/ THREADED ROD w/ 8 HHDQ14-SDS2.5 (1)6x 13710 10745 HEAVY SQ. NUT ANDHEAVY SQ. NUT AND WASHER @ BOT. WASHER @ BOT. PROVIDE 24"EMBEDPROVIDE 24" EMBED INTO CONT FTG. INTO CONT FTG. 5 MSTC28 (2)2x 3000 2590 N/A N/A 6 IVSTC40 (2)2x 4335 3745 N/A N/A 7 MSTC66 (2)2x 5660 5660 N/A N/A Notes: 1 . Install all holdowns per manufactureer specificaiton per latest Simpson Strong Tie catalog. 2. Match studs on schedule for walls below on all wall to wall holdowns. 3. (Multiple)2x studs nailed together with (2) rows of 16d @ 3" o.c. staggered. 4. Refer to shearwall schedule and typical shearwall details for wall locations and configurations. 5. Refer to Simpson catalog for minimum embed of anchors into concrete. Use menu item Settings>Printing&Title Block Title : 5'-0"Wall Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 5'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To: CORE ENGINEERING LCriteria I Soil Data Retained Height = 5.00 ft Allow Soil Bearing = 1,500.0 psf Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00: 1 = Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf FootingiiSoil Friction = 0.350 Soil height to ignore for passive pressure = 12.00 in Surcharge Loads I L Lateral Load Applied to Stem A Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft has been increased Axial Load Applied to Stem ` 1.00 Footing Type i by a factor of Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem= 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Poisson's Ratio = 0.300 Axial Load Eccentricity = 0.0 in Design Summary I Stem Construction I Top Stem Stem OK Wall Stability Ratios Design Height Above Ftg ft= 0.00 Overturning = 4.52 OK Wall Material Above"Ht" = Concrete Sliding = 1.64 OK Thickness = 8.00 Rebar Size = # 5 Total Bearing Load = 3,302 lbs Rebar Spacing = 18.00 ...resultant ecc. = 6.43 in Rebar Placed at = Center Design Data Soil Pressure @ Toe = 1,365 psf OK fb/FB+fa/Fa = 0.407 Soil Pressure @ Heel = 189 psf OK Total Force @ Section lbs= 801.8 Allowable = 1,500 psf Moment....Actual ft-#= 1,421.2 Soil Pressure Less Than Allowable ACI Factored @ Toe = 1,638 psf Moment Allowable = 3,493.2 ACI Factored @ Heel = 227 psf Shear Actual psi= 16.7 Footing Shear @ Toe = 0.0 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 28.4 psi OK Wall Weight = 100.0 Allowable = 75.0 psi Rebar Depth 'd' in= 4.00 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 12.00 Lateral Sliding Force = 706.4 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 6.00 less 100%Friction Force = - 1,155.6 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data ....for1.5: 1 Stability = 0.0 lbs OK fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors ---- Modular Ratio'n' = Building Code IBC 2009,ACI Short Term Factor = Dead Load 1.200 Equiv.Solid Thick. = Live Load 1.600 Masonry Block Type = Medium Weight Earth,H 1.600 Masonry Design Method = ASD Concrete Data Wind,W 1.600 fc psi= 2,500.0 Seismic,E 1.000 Fy psi= 60,000.0 • Use menu item Settings>Printing&Title Block Title : 5'-0"Wall Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 5'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To: CORE ENGINEERING Footing Dimensions & Strengths 1 Footing Design Results Toe Width = 0.00 ft Toe Heel Heel Width = 4.25 Factored Pressure = 1,638 227 psf Total Footing Width = 4.25 Mu':Upward = 0 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 0 411 ft-# Mu: Design = 0 411 ft-# Key Width = 0.00 in Actual 1-Way Shear = 0.00 28.42 psi Key Depth = 0.00 in Allow 1-Way Shear = 0.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #4 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #4 @ 18.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd, Mu<S*Fr Heel:Not req'd, Mu<S*Fr Key: No key defined Summary of Overturning & Resisting Forces & Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item - lbs ft ft-# lbs ft ft-# Heel Active Pressure = 630.0 2.00 1,260.0 Soil Over Heel = 1,970.8 2.46 4,845.0 Surcharge over Heel = 76.4 3.00 229.1 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 143.3 2.46 352.4 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = = Soil Over Toe = 1,970.8 Surcharge Over Toe = Total 706.4 O.T.M. 1,489.1 Stem Weight(s) = 550.0 0.33 183.3 Earth @ Stem Transitions= Footing Weight = 637.5 2.13 1,354.7 Resisting/Overturning Ratio = 4.52 Key Weight = Vertical Loads used for Soil Pressure= 3,301.7 lbs Vert.Component = Total= 3,301.7 lbs R.M.= 6,735.3 Axial live load NOT included in total displayed,or used for overturning resistance,but is included for soil pressure calculation. DESIGNER NOTES: • Use menu item Settings>Printing&Title Block Title : 5'-0"Wall with seismic Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 5'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Criteria I Soil Data Retained Height = 5.00 ft Allow Soil Bearing = 1,995.0 psf - Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00: 1 = Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf may; Soil Density,Toe = 110.00 pcf FootingiISoil Friction = 0.350 Soil height to ignore for passive pressure = 12.00 in Surcharge Loads I Lateral Load Applied to Stem ' [Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft has been increased 1.00 Footing Axial Load Applied to Stem by a factor of Type Base Above/Below Soil 0.0 ft Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall Axial Live Load = 0.0 lbs Poisson's Ratio = 0.300 Axial Load Eccentricity = 0.0 in Earth Pressure Seismic Load a Kae for seismic earth pressure = 0.389 Added seismic base force 157.6 lbs Design Kh = 0.166 g Ka for static earth pressure = 0.277 Difference: Kae-Ka = 0.112 Using Mononobe-Okabe/Seed-Whitman procedure Stern Weight Seismic Load 1 Fp/Wp Weight Multiplier = 0.400 g Added seismic base force 157.1 lbs • Use menu item Settings>Printing&Title Block Title : 5'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 5'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Design Summary ' Stern Construction 1 Top Stem Wall StabilityRatios Stem OK Design Height Above Ftc ft= 0.00 Overturning = 2.55 OK Wall Material Above"Ht" = Concrete Sliding = 1.13 Ratio<1.5! Thickness = 8.00 Rebar Size = # 5 Total Bearing Load = 3,302 lbs Rebar Spacing = 18.00 ...resultant ecc. = 10.64 in Rebar Placed at = Center Design Data Soil Pressure @ Toe = 1,777 psf OK fb/FB+fa/Fa = 0.712 Soil Pressure @ Heel = 0 psf OK Total Force @ Section lbs= 1,175.9 Allowable = 1,995 psf Moment....Actual ft-#= 2,488.6 Soil Pressure Less Than Allowable ACI Factored @ Toe = 2,132 psf Moment Allowable = 3,493.2 ACI Factored @ Heel = 0 psf Shear Actual psi= 21.3 Footing Shear @ Toe = 0.0 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 28.4 psi OK Wall Weight = 100.0 Allowable = 75.0 psi Rebar Depth 'd' in= 4.00 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 16.67 Lateral Sliding Force = 1,021.1 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 6.00 less 100%Friction Force = - 1,155.6 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data --- ....for 1.5: 1 Stability = 376.1 lbs NG fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors Modular Ratio'n' = Building Code IBC 2009,ACI Short Term Factor = Dead Load 1.200 Equiv.Solid Thick. = Live Load 1.600 Masonry Block Type = Medium Weight Earth,H 1.600 Masonry Design Method = ASD Concrete Data Wind,W 1.600 fc Seismic,E 1.000 psi= 2,500.0 Fy psi= 60,000.0 Footing Dimensions &Strengths M i Footing Design Resultsil Toe Width = 0.00 ft Toe Heel Heel Width = 4.25 Factored Pressure = 2,132 0 psf Total Footing Width = 4.25 Mu':Upward = 0 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 0 411 ft-# Mu: Design = 0 411 ft-# Key Width = 0.00 in Actual 1-Way Shear = 0.00 28.42 psi Key Depth = 0.00 in Allow 1-Way Shear = 0.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #4 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #4 @ 18.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined Use menu item Settings>Printing&Title Block Title : 5'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 5'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Summary of Overturning & Resisting Forces & Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft ft-# Heel Active Pressure = 630.0 2.00 1,260.0 Soil Over Heel = 1,970.8 2.46 4,845.0 Surcharge over Heel = 76.4 3.00 229.1 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 143.3 2.46 352.4 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = Seismic Earth Load = 157.6 3.60 567.3 Soil Over Toe = 1,970.8 Seismic Stem Self Wt = 220.0 3.75 825.0 Surcharge Over Toe = Stem Weight(s) = 550.0 0.33 183.3 Total 1,021.1 O.T.M. 2,645.7 Earth @ Stem Transitions= = Footing Weight = 637.5 2.13 1,354.7 Resisting/Overturning Ratio = 2.55 Key Weight = Vertical Loads used for Soil Pressure= 3,301.7 lbs Vert.Component = Total= 3,301.7 lbs R.M.= 6,735.3 If seismic included the min.OTM and sliding *Axial live load NOT included in total displayed,or used for overturning ratios may be 1.1 per IBC'09, 1807.2.3. resistance,but is included for soil pressure calculation. DESIGNER NOTES: Use menu item Settings>Printing&Title Block Title : 6'-0"Wall Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 6'-0"retained This Wall in File:g:1structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Criteria Soil Data I Retained Height = 6.00 ft Allow Soil Bearing = 1,500.0 psf Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft „, 1,....,,,-, ,:,_,:-.4‘7ii,,,',1: Slope Behind Wall = 0.00: 1 - Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf FootingilSoil Friction = 0.350 44 Soil height to ignore 15:{ , for passive pressure = 12.00 in Surcharge Loads 0 Lateral Load Applied to Ste Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft Axial Load Applied to Stem has been increased 1.00 by a factor of Footing Type Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Poisson's Ratio = 0.300 Axial Load Eccentricity = 0.0 in Design Summary I Stem Construction -I Top Stem Stem OK Wall Stability Ratios Design Height Above Ftc ft= 0.00 Overturning = 4.63 OK Wall Material Above"Ht" = Concrete Sliding = 1.57 OK Thickness = 8.00 Rebar Size = # 5 Total Bearing Load = 4,258 lbs Rebar Spacing = 14.00 ...resultant ecc. = 6.34 in Rebar Placed at = Center Design Data Soil Pressure @ Toe = 1,391 psf OK fb/FB+fa/Fa = 0.541 Soil Pressure @ Heel = 312 psf OK Total Force @ Section lbs= 1,130.2 Allowable = 1,500 psf Moment....Actual ft-#= 2,382.5 Soil Pressure Less Than Allowable ACI Factored©Toe = 1,670 psf Moment Allowable = 4,407.9 ACI Factored @ Heel = 374 psf Shear Actual psi= 23.5 Footing Shear @ Toe = 0.0 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 37.1 psi OK Wall Weight = 100.0 Allowable = 75.0 psi Rebar Depth 'd' in= 4.00 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 12.65 Lateral Sliding Force = 946.6 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 6.00 less 100%Friction Force = - 1,490.4 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data ....for 1.5: 1 Stability = 0.0 lbs OK fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors Modular Ratio'n' = - Short Term Factor Building Code IBC 2009,ACI Equiv.Solid Thick. = Dead Load 1.200 Masonry Block Type = Medium Weight Live Load 1.600 Masonry Design Method = ASD Earth,H 1.600 Concrete Data Wind,W 1.600 f - Seismic,E 1.000 F psi= 2,500.0 Fy psi= 60,000.0 • Use menu item Settings>Printing&Title Block Title : 6'-0"Wall Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 6'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING LFooting Dimensions&Strengths 1 L, Footing Design Results Toe Width = 0.25 ft Toe Heel Heel Width = 4.75 Factored Pressure = 1,670 374 psf Total Footing Width = 5.00 Mu':Upward = 51 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 6 534 ft-# Mu: Design = 46 534 ft-# Key Width = 0.00 in Actual 1-Way Shear = 0.00 37.11 psi Key Depth = 0.00 in Allow 1-Way Shear = 75.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #4 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #4 @ 18.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined Summary of Overturning &Resisting Forces&Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft ft-# Heel Active Pressure = 857.5 2.33 2,000.8 Soil Over Heel = 2,695.0 2.96 7,972.7 Surcharge over Heel = 89.1 3.50 311.8 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 163.3 2.96 483.2 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = = Soil Over Toe = 2,695.0 Surcharge Over Toe = Total 946.6 O.T.M. 2,312.7 Stem Weight(s) = 650.0 0.58 379.2 Earth @ Stem Transitions= = Footing Weight = 750.0 2.50 1,875.0 Resisting/Overturning Ratio = 4.63 Key Weight = Vertical Loads used for Soil Pressure= 4,258.3 lbs Veil.Component = Total= 4,258.3 lbs R.M.= 10,710.1 *Axial live load NOT included in total displayed,or used for overturning resistance,but is included for soil pressure calculation. DESIGNER NOTES: Use menu item Settings>Printing&Title Block to set these five lines of information Title 6'-0"Wall with seismic Page: Job# Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 6'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Criteria i Soil Data Retained Height = 6.00 ft Allow Soil Bearing = 1,995.0 psf ` . " Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Slope Behind Wall = 0.00: 1 Heel Active Pressure = 35.0 psf/ft Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density, Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf FootinglISoil Friction = 0.350 Soil height to ignore for passive pressure = 12.00 in Surcharge Loads I I Lateral Load Applied to Stem ,Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning Surcharge Over Toe = 0.0 sf _..Height to Top = 0.00 ft Footing Width = 0.00 ft p Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft Axial Load Applied to Stem has a beenfactor increasedof 1.00 Footing Type b Axial Dead Load = 0.0 lbs Base Above/Below Soil Axial Live Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Load Eccentricity = 0.0 in Poisson's Ratio = 0.300 1 Earth Pressure Seismic Load 1 Kae for seismic earth pressure = 0.389 Added seismic base force 214.5 lbs Ka for static earth pressure = 0.277 Design Kh = 0.166 g Using Mononobe-Okabe/Seed-Whitman procedureDifference: Kae-Ka = 0.112 Stem Weight Seismic Load a Fp/Wp Weight Multiplier = 0.400 g Added seismic base force 185.7 lbs • Use menu item Settings>Printing&Title Block Title : 6'-0"Wall with seismic Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 6'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING [Design Summary 1 Stem Construction I Top Stem Stem OK Wall Stability Ratios Design Height Above Ftc ft= 0.00 Overturning = 2.68 OK Wall Material Above"Ht" = Concrete Sliding = 1.11 Ratio<1.5! Thickness = 8.00 Rebar Size = # 5 Total Bearing Load = 4,258 lbs Rebar Spacing = 14.00 ...resultant ecc. = 11.10 in Rebar Placed at = Center Design Data -- Soil Pressure @ Toe = 1,802 psf OK fb/FB+fa/Fa = 0.913 Soil Pressure @Heel = 0 psf OK Total Force @ Section lbs= 1,612.1 Allowable = 1,995 psf Moment....Actual ft-#= 4,026.6 Soil Pressure Less Than Allowable ACI Factored @ Toe = 2,163 psf Moment Allowable = 4,407.9 ACI Factored @ Heel = 0 psf Shear Actual psi= 29.0 Footing Shear @ Toe = 0.0 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 37.1 psi OK Wall Weight = 100.0 Allowable = 75.0 psi Rebar Depth 'd' in= 4.00 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 21.38 Lateral Sliding Force = 1,346.8 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 7.39 less 100%Friction Force = - 1,490.4 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data - ....for 1.5: 1 Stability = 529.8 lbs NG fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors Modular Ration' = Building Code IBC 2009,ACI Short Term Factor = Dead Load 1.200 Equiv.Solid Thick. = Live Load 1.600 Masonry Block Type = Medium Weight Earth,H 1.600 Masonry Design Method = ASD Wind,W 1.600 Concrete Data - fc psi= 2,500.0 Seismic,E 1.000 Fy psi= 60,000.0 Footing Dimensions&Strengths 1 Footing Design Results Toe Width = 0.25 ft Toe Heel Heel Width = 4.75 Factored Pressure = 2,163 0 psf Total Footing Width = 5.00 Mu':Upward = 66 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 6 534 ft-# Mu: Design = 61 534 ft-# Key Width = 0.00 in Actual 1-Way Shear = 0.00 37.11 psi Key Depth = 0.00 in Allow 1-Way Shear = 75.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #4 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #4 @ 18.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined Use menu item Settings>Printing&Title Block Title : 6'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 6'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Summary of Overturning & Resisting Forces & Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft ft-# Heel Active Pressure = 857.5 2.33 2,000.8 Soil Over Heel = 2,695.0 2.96 7,972.7 Surcharge over Heel = 89.1 3.50 311.8 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 163.3 2.96 483.2 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = Seismic Earth Load = 214.5 4.20 900.8 Soil Over Toe = 2,695.0 Seismic Stem Self Wt = 260.0 4.25 1,105.0 Surcharge Over Toe = - - Stem Weight(s) = 650.0 0.58 379.2 Total 1,346.8 O.T.M. 4,002.8 Earth @ Stem Transitions= Footing Weight = 750.0 2.50 1,875.0 Resisting/Overturning Ratio = 2.68 Key Weight = Vertical Loads used for Soil Pressure= 4,258.3 lbs Vert.Component = Total= 4,258.3 lbs R.M.= 10,710.1 If seismic included the min.OTM and sliding *Axial live load NOT included in total displayed,or used for overturning ratios may be 1.1 per IBC'09, 1807.2.3. resistance,but is included for soil pressure calculation. DESIGNER NOTES: Use menu item Settings>Printing&Title Block Title : 7'-0"Wall Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 7'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING [Criteria II Soil Data Retained Height = 7.00 ft Allow Soil Bearing = 1,500.0 psf Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00:1 Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf FootingliSoil Friction = 0.350 Soil height to ignore for passive pressure = 12.00 in ' Surcharge Loads 1 [ Lateral Load Applied to Stem 0 [Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft Axial Load Applied to Stem has been increased 1.00 Footing Type by a factor of Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Poisson's Ratio = 0.300 Axial Load Eccentricity = 0.0 in Design Summary I Stem Construction I Top Stem Stem OK Wall Stability Ratios Design Height Above Ftc ft= 0.00 Overturning = 5.11 OK Wall Material Above"Ht" = Concrete Sliding = 1.59 OK Thickness = 8.00 Rebar Size = # 5 Total Bearing Load = 5,565 lbs Rebar Spacing = 8.00 ...resultant ecc. = 5.90 in Rebar Placed at = Center Design Data Soil Pressure @ Toe = 1,383 psf OK fb/FB+fa/Fa = 0.512 Soil Pressure @ Heel = 472 psf OK Total Force @ Section lbs= 1,514.5 Allowable = 1,500 psf Moment....Actual ft-#= 3,700.2 Soil Pressure Less Than Allowable ACI Factored @ Toe = 1,660 psf Moment Allowable = 7,221.8 ACI Factored @ Heel = 566 psf Shear Actual psi= 31.6 Footing Shear @ Toe = 0.0 psi OK Shear Allowable psi= 75.0 Footing Shear©Heel = 49.5 psi OK Wall Weight = 100.0 Allowable = 75.0 psi Rebar Depth 'd' in= 4.00 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 12.00 Lateral Sliding Force = 1,221.8 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 6.00 less 100%Friction Force = - 1,947.8 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data - ....for 1.5: 1 Stability = 0.0 lbs OK fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors - Modular Ratio'n' = Building Code IBC 2009,ACI Short Term Factor = Dead Load 1.200 Equiv.Solid Thick. = Live Load 1.600 Masonry Block Type = Medium Weight Earth,H 1.600 Masonry Design Method = ASD Concrete Data Wind,W 1.600 fc psi= 2,500.0 Seismic,E 1.000 Fy psi= 60,000.0 Use menu item Settings>Printing&Title Block Title ; 7'-0"Wall Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 7'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\bl RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Footing Dimensions &Strengths Footing Design Results Toe Wdth = 0.50 ft Toe Heel Heel Width = 5.50 Factored Pressure = 1,660 566 psf Total Footing Width = 6.00 Mu':Upward = 204 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 23 748 ft-# KeyWidth = Mu: Design = 181 748 ft-# 0.00 in Actual 1-WayShear = 0.00 49.52 psi Key Depth = 0.00 in Key Distance from Toe = 0.00 ft Allow 1-Way Shear = 75.00 75.00 psi Toe Reinforcing = #4 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #4 @ 18.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined L Summary of Overturning &Resisting Forces&Moments II OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft ft-# Heel Active Pressure = 1,120.0 2.67 2,986.7 Soil Over Heel = 3,721.7 3.58 13,336.0 Surcharge over Heel = 101.8 4.00 407.3 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 193.3 3.58 692.8 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = = Soil Over Toe = 3,721.7 Surcharge Over Toe = Total 1,221.8 O.T.M. 3,393.9 Stem Weight(s) = 750.0 0.83 625.0 Earth @ Stem Transitions= = Footing Weight = 900.0 3.00 2,700.0 Resisting/Overturning Ratio = 5.11 Key Weight = Vertical Loads used for Soil Pressure= 5,565.0 lbs Vert.Component = Total= 5,565.0 lbs R.M.= 17,353.8 *Axial live load NOT included in total displayed,or used for overturning resistance,but is included for soil pressure calculation. DESIGNER NOTES: Use menu item Settings>Printing&Title Block Title : 7'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 7'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI318-08,ACI530-08 License To:CORE ENGINEERING Criteria I Soil Data Retained Height = 7.00 ft Allow Soil Bearing = 1,995.0 psf , Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00: 1 Height of Soil over Toe = 0.00 in Passive Pressure250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf FootinglISoil Friction = 0.350 Soil height to ignore for passive pressure = 12.00 in J 1 Surcharge Loads I 1 Lateral Load Applied to Stem • Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ,..Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft has been increased 1.00 Axial Load Applied to Stem Footing Type by a factor of Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Axial Load Eccentricity = 0.0 in Poisson's Ratio = 0.300 Earth Pressure Seismic Load I Kae for seismic earth pressure = 0.389 Added seismic base force 280.1 lbs Ka for static earth pressure =-- 0.277 Design Kh = 0.166 g Difference: Kae-Ka = 0.112 Using Mononobe-Okabe/Seed-Whitman procedure Stem Weight Seismic Load Fp/Wp Weight Multiplier = 0.400 g Added seismic base force 214.3 lbs Use menu item Settings>Printing&Title Block Title : 7'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 7'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Design Summary Stem Construction 1 Top Stem Stem OK Wall Stability Ratios Design Height Above Ftc ft= 0.00 Overturning = 3.01 OK Wall Material Above"Ht" = Concrete Sliding = 1.13 Ratio<1.5! Thickness = 8.00 Rebar Size = # 5 Total Bearing Load = 5,565 lbs Rebar Spacing = 8.00 ...resultant ecc. = 10.99 in Rebar Placed at = Center Design Data Soil Pressure @ Toe = 1,777 psf OK fb/FB+fa/Fa = 0.844 Soil Pressure @Heel = 78 psf OK Total Force @ Section lbs= 2,116.6 Allowable = 1,995 psf Moment....Actual ft-#= 6,094.0 Soil Pressure Less Than Allowable ACI Factored @ Toe = 2,133 psf Moment Allowable = 7,221.8 ACI Factored @ Heel = 93 psf Shear Actual psi= 37.8 Footing Shear @ Toe = 0.0 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 49.5 psi OK Wall Weight = 100.0 Allowable = 75.0 psi Rebar Depth 'd' in= 4.00 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 19.75 Lateral Sliding Force = 1,716.3 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 6.84 less 100%Friction Force = - 1,947.8 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data ....for 1.5: 1 Stability = 626.6 lbs NG fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors Modular Ration' = Building Code IBC 2009,ACI Short Term Factor = Dead Load 1.200 Equiv.Solid Thick. = Live Load 1.600 Masonry Block Type = Medium Weight Earth,H 1.600 Masonry Design Method = ASD Concrete Data Wind,W 1.600 fc psi= 2,500.0 Seismic,E 1.000 Fypsi= 60,000.0 Footing Dimensions &Strengths 1 1-Footing Design Results 1 Toe Width = 0.50 ft Toe Heel Heel Width = 5.50 Factored Pressure = 2,133 93 psf Total Footing Width = 6.00 Mu':Upward = 259 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 23 748 ft-# Mu: Design = 237 748 ft-# Key Width = 0.00 in Actual 1-Way Shear = 0.00 49.52 psi Key Depth = 0.00 in Allow 1-Way Shear = 75.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #4 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #4 @ 18.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S'Fr Heel:Not req'd,Mu<S*Fr Key: No key defined Use menu item Settings> Printing&Title Block Title : 7'-0"Wall with seismic Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 7'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To: CORE ENGINEERING Summary of Overturning &Resisting Forces& Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft ft-# Heel Active Pressure = 1,120.0 2.67 2,986.7 Soil Over Heel = 3,721.7 3.58 13,336.0 Surcharge over Heel = 101.8 4.00 407.3 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 193.3 3.58 692.8 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = Seismic Earth Load = 280.1 4.80 1,344.7 Soil Over Toe = 3,721.7 Seismic Stem Self Wt = 300.0 4.75 1,425.0 Surcharge Over Toe = Total 1,716.3 O.T.M. 5,756.5 Stem Weight(s) = 750.0 0.83 625.0 Earth @ Stem Transitions= Footing Weight = 900.0 3.00 2,700.0 Resisting/Overturning Ratio = 3.01 Key Weight = Vertical Loads used for Soil Pressure= 5,565.0 lbs Veil.Component = Total= 5,565.0 lbs R.M.= 17,353.8 If seismic included the min.OTM and sliding *Axial live load NOT included in total displayed,or used for overturning ratios may be 1.1 per IBC'09, 1807.2.3. resistance,but is included for soil pressure calculation. DESIGNER NOTES: Use menu item Settings>Printing&Title Block Title : 8'-0"Wall Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 8'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Criteria ' Soil Data I Retained Height = 8.00 ft Allow Soil Bearing = 1,500.0 psf .,. , Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active = Slope Behind Wall = 0.00: 1 ct ve Pressure 35.0 psf/ft Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf . FootingjiSoil Friction = 0.350 Soil height to ignore for passive pressure = 12.00 in I Surcharge Loads i Lateral Load Applied to Stem I Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft Axial Load Applied to Stem has been increased 1.00 Footing Type by a factor of Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Axial Load Eccentricity = 0.0 in Poisson's Ratio = 0.300 Design Summary I Stem Construction I Top Stem Wall StabilityRatios Stem OK Design Height Above Ftc ft= 0.00 Overturning = 5.11 OK Wall Material Above"Ht" = Concrete Sliding = 1.55 OK Thickness = 8.00 Rebar Size = # 5 Total Bearing Load = 6,769 lbs Rebar Spacing = 10.00 ...resultant ecc. = 5.74 in Rebar Placed at = Edge Design Data Soil Pressure @ Toe = 1,430 psf OK fb/FB+fa/Fa = 0.564 Soil Pressure @ Heel = 576 psf OK Allowable = 1,500 Total Force @ Section lbs= 1,954.9 psf Moment....Actual ft-#= 5,430.3 Soil Pressure Less Than Allowable ACI Factored @ Toe = 1,715 psf Moment Allowable = 9,623.1 ACI Factored @ Heel = 691 psf Shear Actual psi= 26.3 Footing Shear @ Toe = 0.6 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 60.8 psi OK Wall Weight = 100.0 Allowable = 75.0 psi Rebar Depth 'd' in= 6.19 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 13.20 Lateral Sliding Force = 1,532.0 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 6.00 less 100%Friction Force = - 2,369.2 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data - ....for 1.5: 1 Stability = 0.0 lbs OK fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors Modular Ratio'n' = - Short Term Factor Building Code IBC 2009,ACI = Dead Load 1.200 Equiv.Solid Thick. = Live Load 1.600 Masonry Block Type = Medium Weight Earth,H 1.600 Masonry Design Method = ASD Wind,W Concrete Data 1.600 pc psi= 2,500.0 Seismic, E 1.000 Fy psi= 60,000.0 Use menu item Settings>Printing&Title Block Title : 8'-0"Wall Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 8'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Footing Dimensions &Strengths I Footing Design Results Toe Width = 0.75 ft Toe Heel Heel Width = 6.00 Factored Pressure = 1,715 691 psf Total Footing Width = 6.75 Mu':Upward = 472 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 51 910 ft-# KeyWidth = Mu: Design = 421 910 ft-# 0.00 in Actual 1-WayShear = 0.63 60.82 psi Key Depth = 0.00 in Key Distance from Toe = 0.00 ft Allow 1-Way Shear = 75.00 75.00 psi Toe Reinforcing = #5 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #5 @ 10.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined Summary of Overturning & Resisting Forces&Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft ft-# Heel Active Pressure = 1,417.5 3.00 4,252.5 Soil Over Heel = 4,693.3 4.08 19,164.4 Surcharge over Heel = 114.5 4.50 515.5 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 213.3 4.08 871.1 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = = Soil Over Toe = 4,693.3 Surcharge Over Toe = Total 1,532.0 O.T.M. 4,768.0 Stem Weight(s) = 850.0 1.08 920.8 Earth @ Stem Transitions= Footing Weight = 1,012.5 3.38 3,417.2 Resisting/Overturning Ratio = 5.11 Key Weight = Vertical Loads used for Soil Pressure= 6,769.2 lbs Vert.Component = Total= 6,769.2 lbs R.M.= 24,373.6 *Axial live load NOT included in total displayed,or used for overturning resistance,but is included for soil pressure calculation. DESIGNER NOTES: Use menu item Settings>Printing&Title Block Title : 8'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 8'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Criteria I 1 Soil Data I I Retained Height = 8.00 ft Allow Soil Bearing = 1,995.0 psf Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00: 1 = Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf ", Soil Density,Toe = 110.00 pcf 1 IP FootingliSoil Friction = 0.350 Soil height to ignore for passivePressure = 12.00 in Surcharge Loads I LLateral Load Applied to Stem ' Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft has been increased 1.00 Footing Type Axial Load Applied to Stem by a factor of Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Axial Load Eccentricity = 0.0 in Poisson's Ratio = 0.300 Earth Pressure Seismic Load 1 Kae for seismic earth pressure = 0.389 Added seismic base force 354.6 lbs 1 Ka for static earth pressure = 0.277 Design Kh = 0.166 g Difference: Kae-Ka = 0.112 Using Mononobe-Okabe/Seed-Whitman procedure Stern Weight Seismic Load 1 Fp/Wp Weight Multiplier = 0.400 g Added seismic base force 242.9 lbs Use menu item Settings>Printing&Title Block Title : 8'-0"Wall with seismic Page to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 8'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Lpesign Summary ' Stem Construction ' Top Stem Stem OK Wall Stability Ratios Design Height Above FtE ft= 0.00 Overturning = 3.06 OK Wall Material Above"Ht" = Concrete Sliding = 1.11 Ratio<1.5! Thickness = 8.00 Rebar Size = # 5 Total Bearing Load = 6,769 lbs Rebar Spacing = 10.00 ...resultant ecc. = 11.40 in Rebar Placed at = Edge Soil Pressure @ Toe = 1,850 psf OK Design Data = Soil Pressure @ Heel = 156 psf OK /FB+fa/Fa = 0.911 Allowable = 1,995 Total Force @ Section lbs2,689.5 psf Moment....Actual ft-#= 8,769.3 Soil Pressure Less Than Allowable ACI Factored @ Toe = 2,219 psf Moment Allowable = 9,623.1 ACI Factored @ Heel = 187 psf Shear Actual psi= 30.9 Footing Shear @ Toe = 0.8 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 60.8 psi OK Wall Weight = 100.0 Allowable = 75.0 psi Rebar Depth 'd' in= 6.19 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 21.32 Lateral Sliding Force = 2,129.5 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 7.84 less 100%Friction Force = - 2,369.2 lbs Lap splice above base reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data Hook embedment reduced by stress ratio ....for 1.5: 1 Stability = 825.0 lbs NG fm psi= Fs psi= Solid Grouting = Use Half Stresses = Modular Ratio'n' = Load Factors Building Code IBC 2009,ACI Short Term Factor = Dead Load 1.200 Equiv.Solid Thick. = Live Load 1.600 Masonry Block Type = Medium Weight Masonry Design Method = ASD Earth,H 1.600 Concrete Data Wind,W 1.600 fc psi= 2,500.0 Seismic,E 1.000 Fy psi= 60,000.0 Footing Dimensions &Strengths I1FootingDesign Results Toe Width = 0.75 ft Toe Heel Heel Width = 6.00 Factored Pressure = 2,219 187 psf Total Footing Width = 6.75 Mu':Upward = 603 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 51 910 ft-# Mu: Design = 552 910 ft-# Key Width = 0.00 in Actual 1-Way Shear = 0.83 60.82 psi Key Depth = 0.00 in Allow 1-Way Shear = 75.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #5 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #5 @ 10.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Cover @ Top 2.00 @ Btm.= 3.00 in Other Acceptable Sizes&Spacings Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S'Fr Key: No key defined Use menu item Settings>Printing&Title Block Title : 8'-0"Wall with seismic Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 8'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Summary of Overturning &Resisting Forces&Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft _ ft-# Heel Active Pressure = 1,417.5 3.00 4,252.5 Soil Over Heel = 4,693.3 4.08 19,164.4 Surcharge over Heel = 114.5 4.50 515.5 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 213.3 4.08 871.1 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = Seismic Earth Load = 354.6 5.40 1,914.6 Soil Over Toe = 4,693.3 Seismic Stem Self Wt = 340.0 5.25 1,785.0 Surcharge Over Toe = Total 2,129.5 O.T.M. 7,957.6 Stem Weight(s) = 850.0 1.08 920.8 Earth @ Stem Transitions= Footing Weight = 1,012.5 3.38 3,417.2 Resisting/Overturning Ratio = 3.06 Key Weight = Vertical Loads used for Soil Pressure= 6,769.2 lbs Veil.Component = Total= 6,769.2 lbs R.M.= 24,373.6 If seismic included the min.OTM and sliding *Axial live load NOT included in total displayed,or used for overturning ratios may be 1.1 per IBC'09, 1807.2.3. resistance,but is included for soil pressure calculation. DESIGNER NOTES: Use menu item Settings>Printing&Title Block Title : 9'-0"Wall Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 9'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING [Criteria ' [Soil Data - ._. Retained Height = 9.00 ft Allow Soil Bearing = 1,500.0 psf Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00: 1 Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft 1 Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf > Soil Density,Toe = 110.00 pcf FootingliSoil Friction = 0.350 Soil height to ignore for passive pressure = 12.00 in , ,,-- J Surcharge Loads 1 Lateral Load Applied to Stem 11 Lftdjacent Footing Load Surcharge Over Heel = 40.0 psf = r Used To Resist Sliding&Overturning Lateral Load 0.0#/ft Adjacent Footing Load 0.0 lbs ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft has been increased 1.00 Axial Load Applied to Stem Footing Type by a factor of Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem= 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Axial Load Eccentricity = 0.0 in Poisson's Ratio = 0.300 Design Summary I Stem Construction I Top Stem Wall StabilityRatios -. Stem OK Design Height Above Ftc ft= 0.00 Overturning = 5.80 OK Wall Material Above"Ht" = Concrete Sliding = 1.58 OK Thickness = 10.00 Rebar Size = # 5 Total Bearing Load = 8,482 lbs Rebar Spacing = 10.00 ...resultant ecc. = 4.09 in Rebar Placed at = Edge Design Data Soil Pressure @ Toe = 1,331 psf OK fb/FB+fa/Fa = 0.588 Soil Pressure @ Heel = 789 psf OK Total Force @ Section lbs= 2,451.3 Allowable = 1,500 psf Moment....Actual ft-#= 7,628.7 Soil Pressure Less Than Allowable ACI Factored @ Toe = 1,598 psf Moment Allowable = 12,971.1 ACI Factored @ Heel = 947 psf Shear Actual psi= 24.9 Footing Shear @ Toe = 7.4 psi OK Shear Allowable psi= 75.0 Footing Shear©Heel = 74.3 psi OK Wall Weight = 125.0 Allowable = 75.0 psi Rebar Depth 'd' in= 8.19 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 13.76 Lateral Sliding Force = 1,877.3 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 6.03 less 100%Friction Force = - 2,968.6 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data ....for 1.5: 1 Stability = 0.0 lbs OK fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors Modular Ratio'n' = - - - Short Term Factor Building Code IBC 2009,ACI Equiv.Solid Thick. Dead Load 1.200 Masonry Block Type = Medium Weight Live Load 1.600 Earth,H 1.600 Masonry Design Method = ASD Concrete Data - - - Wind,W 1.600 fc psi= 2,500.0 Seismic, E 1.000 Fy psi= 60,000.0 Use menu item Settings>Printing&Title Block Title : 9'-0"Wall Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 9'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Footing Dimensions &Strengths 1 L, Footing Design Results Toe Width = 1.25 ft Toe Heel Heel Width = 6.75 Factored Pressure = 1,598 947 psf Total Footing Width = 8.00 Mu':Upward = 1,222 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 141 1,120 ft-# Mu: Design = 1,081 1,120 ft-# Key Width = 0.00 in Actual 1-Way Shear = 7.41 74.32 psi Key Depth = 0.00 in Allow 1-Way Shear = 75.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #5 @ 18.00 in Pc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #5 @ 10.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined Summary of Overturning & Resisting Forces&Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# _ lbs ft ft-# Heel Active Pressure = 1,750.0 3.33 5,833.3 Soil Over Heel = 5,857.5 5.04 29,531.6 Surcharge over Heel = 127.3 5.00 636.4 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 236.7 5.04 1,193.2 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = = Soil Over Toe = 5,857.5 Surcharge Over Toe = Total 1,877.3 O.T.M. 6,469.7 Stem Weight(s) = 1,187.5 1.67 1,979.2 Earth @ Stem Transitions= Footing Weight = 1,200.0 4.00 4,800.0 Resisting/Overturning Ratio = 5.80 Key Weight = Vertical Loads used for Soil Pressure= 8,481.7 lbs Vert.Component Total= 8,481.7 lbs R.M.= 37,503.9 *Axial live load NOT included in total displayed,or used for overturning resistance,but is included for soil pressure calculation. DESIGNER NOTES: • • Use menu item Settings>Printing&Title Block Title : 9'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 9'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Criteria I Soil Data Retained Height = 9.00 ft Allow Soil Bearing = 1,995.0 psf Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method 71, Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00: 1 = I Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density, Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf FootinglISoil Friction = 0.350 Soil height to ignore kl for passive pressure = 12.00 in i Surcharge Loads I Lateral Load Applied to Stem ' [Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ,..Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft Axial Load Applied to Stem has been increased 1.00 Footing Type Line Load by a factor of Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Poisson's Ratio = 0.300 Axial Load Eccentricity = 0.0 in Earth Pressure Seismic Load i Kae for seismic earth pressure = 0.389 Added seismic base force 437.7 lbs Design Kh = 0.166 g Ka for static earth pressure = 0.277 Difference: Kae-Ka = 0.112 Using Mononobe-Okabe/Seed-Whitman procedure Stem Weight Seismic Load 1 Fp/Wp Weight Multiplier = 0.400 g Added seismic base force 339.3 lbs Use menu item Settings>Printing&Title Block Title : 9'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 9'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Design Summary I L,Stem Construction 1 Top Stem Wall StabilityRatios Stem OK Design Height Above Ftc ft= 0.00 Overturning = 3.39 OK Wall Material Above"Ht" = Concrete Sliding = 1.12 Ratio<1.5! Thickness = 10.00 Rebar Size = # 5 Total Bearing Load = 8,482 lbs Rebar Spacing = 10.00 ...resultant ecc. = 10.57 in Rebar Placed at = Edge Soil Pressure @ Toe = 1,760 psf OK Design Data Soil Pressure @ Heel = 360 psf OK fb�FB+fa/Fa = 0.970 Allowable = 1,995 Total Force @ Section lbs= 3,425.7 psf Moment....Actual ft-#= 12,581.6 Soil Pressure Less Than Allowable ACI Factored @Toe = 2,113 psf Moment Allowable = 12,971.1 ACI Factored @ Heel = 432 psf Shear Actual psi= 29.8 Footing Shear @ Toe = 10.0 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 74.3 psi OK Wall Weight = 125.0 Allowable = 75.0 psi Rebar Depth 'd' in= 8.19 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 22.70 Lateral Sliding Force = 2,654.3 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 0.0 lbs HOOK EMBED INTO FTG in= 8.26 less 100%Friction Force = - 2,968.6 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data ....for 1.5: 1 Stability = 1,012.8 lbs NG fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors Modular Ratio'n' = Building Code IBC 2009,ACI Short Term Factor = Dead Load 1.200 Equiv.Solid Thick. _ Live Load 1.600 Masonry Block Type = Medium Weight Earth,H 1.600 Masonry Design Method = ASD Wind,W 1.600 fConcrete Data Seismic,E 1.000 Fy psi= 2,500.0 FY psi= 60,000.0 Footing Dimensions&Strengths I Footing Design Results Toe Width = 1.25 ft Toe Heel Heel Width = 6.75 Factored Pressure = 2,113 432 psf Total Footing Width = 8.00 Mu':Upward = 1,582 0 ft-# Footing Thickness = 12.00 in Mu':Downward = 141 1,120 ft-# KeyWidth = Mu: Design = 1,441 1,120 ft-# 0.00 in Actual 1-WayShear = 9.96 74.32 psi Key Depth = 0.00 in Key Distance from Toe = 0.00 ft Allow 1-Way Shear = 75.00 75.00 psi Toe Reinforcing = #5 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #5 @ 10.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined Use menu item Settings>Printing&Title Block Title : 9'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 9'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING L Summary of Overturning & Resisting Forces&Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item _ lbs ft ft-# lbs ft ft-# Heel Active Pressure = 1,750.0 3.33 5,833.3 Soil Over Heel = 5,857.5 5.04 29,531.6 Surcharge over Heel = 127.3 5.00 636.4 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 236.7 5.04 1,193.2 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = Seismic Earth Load = 437.7 6.00 2,626.4 Soil Over Toe = 5,857.5 Seismic Stem Self Wt = 475.0 5.75 2,731.3 Surcharge Over Toe = Total 2,654.3 O.T.M. 11,047.0 Stem Weight(s) = 1,187.5 1.67 1,979.2 Earth @ Stem Transitions= = Footing Weight = 1,200.0 4.00 4,800.0 Resisting/Overturning Ratio = 3.39 Key Weight = Vertical Loads used for Soil Pressure= 8,481.7 lbs Vert.Component = Total= 8,481.7 lbs R.M.= 37,503.9 If seismic included the min.OTM and sliding *Axial live load NOT included in total displayed,or used for overturning ratios may be 1.1 per IBC'09, 1807.2.3. resistance,but is included for soil pressure calculation. DESIGNER NOTES: • Use menu item Settings>Printing&Title Block Title : 10'-0"Wall Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 10'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To: CORE ENGINEERING Criteria I �Soil Data Retained Height = 10.00 ft Allow Soil Bearing = 1,500.0 psf Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00: 1 Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf FootingijSoil Friction = 0.350 Soil height to ignore for passive pressure = 12.00 in J Surcharge Loads I Lateral Load Applied to Stem 1 Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft has been increased 1.00 Axial Load Applied to Stem by a factor of Footing Type Line Load Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Poisson's Ratio = 0.300 Axial Load Eccentricity = 0.0 in Design Summary I Stem Construction I Top Stem Stem OK Wall Stability Ratios Design Height Above Ftc ft= 0.00 Overturning = 5.58 OK Wall Material Above"Ht" = Concrete Sliding = 1.55 OK Thickness = 10.00 Rebar Size = # 5 Total Bearing Load = 10,159 lbs Rebar Spacing = 7.50 ...resultant ecc. = 4.26 in Rebar Placed at = Edge Design Data Soil Pressure @ Toe = 1,444 psf OK fb/FB+fa/Fa = 0.610 Soil Pressure @ Heel = 878 psf OK Total Force @ Section lbs= 3,003.6 Allowable = 1,500 psf Moment....Actual ft-#= 10,351.5 Soil Pressure Less Than Allowable ACI Factored @ Toe = 1,733 psf Moment Allowable = 16,968.2 ACI Factored @ Heel = 1,054 psf Shear Actual psi= 30.6 Footing Shear @ Toe = 7.4 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 74.1 psi OK Wall Weight = 125.0 Allowable = 75.0 psi Rebar Depth 'd' in= 8.19 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 14.28 Lateral Sliding Force = 2,324.3 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 45.1 lbs HOOK EMBED INTO FTG in= 6.21 less 100%Friction Force = - 3,555.6 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data ....for 1.5:1 Stability = 0.0 lbs OK fm psi= Fs psi= Solid Grouting = Use Half Stresses = Modular Ratio'n' _ Load Factors -- Short Term Factor Building Code IBC 2009,ACI Equiv.Solid Thick. Dead Load 1.200 Masonry Block Type = Medium Weight Live Load 1.600 Masonry Design Method = ASD Earth,H 1.600 Concrete Data -- Wind,W 1.600 fc psi= 2,500.0 Seismic, E 1.000 Fy psi= 60,000.0 Use menu item Settings>Printing&Title Block Title : 10'-0"Wall Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 10'-0"retained This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To: CORE ENGINEERING Footing Dimensions &Strengths I Footing Design Results ' Toe Width = 1.50 ft Toe Heel Heel Width = 7.25_ Factored Pressure = 1,733 1,054 psf Total Footing Width = 8.75 Mu':Upward = 1,905 0 ft-# Footing Thickness = 14.00 in Mu':Downward = 236 1,318 ft-# Mu: Design = 1,669 1,318 ft-# Key Width = 0.00 in Actual 1-Way Shear = 7.43 74.12 psi Key Depth = 0.00 in Allow 1-Way Shear = 75.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #5 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #5 @ 10.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Cover @ Top 2.00 @ Btm.= 3.00 in Other Acceptable Sizes&Spacings Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined _Summary of Overturning & Resisting Forces&Moments OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft ft-# Heel Active Pressure = 2,182.2 3.72 8,122.5 Soil Over Heel = 7,058.3 5.54 39,114.9 Surcharge over Heel = 142.1 5.58 793.5 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 256.7 5.54 1,422.4 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = = Soil Over Toe = 7,058.3 Surcharge Over Toe = Earth @ Stem Transitions= Total 2,324.3 O.T.M. 8,916.0 Stem Weight(s) 1,312.5 1.92 2,515.6 = = Footing Weight = 1,531.3 4.38 6,699.2 Resisting/Overturning Ratio = 5.58 Key Weight = Vertical Loads used for Soil Pressure= 10,158.8 lbs Vert.Component = Total= 10,158.8 lbs R.M.= 49,752.1 *Axial live load NOT included in total displayed,or used for overturning resistance,but is included for soil pressure calculation. DESIGNER NOTES: Use menu item Settings>Printing&Title Block Title : 10'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 10'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Criteria Soil Data Retained Height = 10.00 ft Allow Soil Bearing = 1,995.0 psf Wall height above soil = 0.50 ft Equivalent Fluid Pressure Method Heel Active Pressure = 35.0 psf/ft Slope Behind Wall = 0.00: 1 = Height of Soil over Toe = 0.00 in Passive Pressure = 250.0 psf/ft Water height over heel = 0.0 ft Soil Density,Heel = 110.00 pcf Soil Density,Toe = 110.00 pcf FootingilSoil Friction = 0.350 kg fA Soil height to ignore for passive pressure = 12.00 in Surcharge Loads i Lateral Load Applied to Stem I Adjacent Footing Load Surcharge Over Heel = 40.0 psf Lateral Load = 0.0#/ft Adjacent Footing Load = 0.0 lbs Used To Resist Sliding&Overturning ...Height to Top = 0.00 ft Footing Width = 0.00 ft Surcharge Over Toe = 0.0 psf ...Height to Bottom = 0.00 ft Eccentricity = 0.00 in Used for Sliding&Overturning The above lateral load Wall to Ftg CL Dist = 0.00 ft has been increased 1.00 Axial Load Applied to Stem by a factor of Footing Type Line Load Base Above/Below Soil Axial Dead Load = 0.0 lbs Wind on Exposed Stem = 0.0 psf at Back of Wall = 0.0 ft Axial Live Load = 0.0 lbs Poisson's Ratio = 0.300 Axial Load Eccentricity = 0.0 in Earth Pressure Seismic Load 0 Kae for seismic earth pressure = 0.389 Added seismic base force 545.8 lbs Ka for static earth pressure = 0.277 Design Kh = 0.166 g Difference: Kae-Ka = 0.112 Using Mononobe-Okabe/Seed-Whitman procedure Stem Weight Seismic Load Fp/Wp Weight Multiplier = 0.400 g Added seismic base force 375.0 lbs Use menu item Settings>Printing&Title Block Title : 10'-0"Wall with seismic Page: to set these five lines of information Job# : Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 10'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING 1.Design Summary I L,Stem Construction I Top Stem Stem OK Wall Stability Ratios Design Height Above Ftc ft= 0.00 Overturning = 3.32 OK Wall Material Above"Ht" = Concrete Sliding = 1.11 Ratio<1.5! Thickness = 10.00 Rebar Size = # 5 Total Bearing Load = 10,159 lbs Rebar Spacing = 7.50 ...resultant ecc. = 11.42 in Rebar Placed at = Edge I Design Data -. Soil Pressure @ Toe = 1,919 psf OK fb/FB+fa/Fa = 0.990 Soil Pressure @ Heel = 403 psf OK Total Force @ Section lbs= 4,145.2 Allowable = 1,995 psf Moment....Actual ft-#= 16,806.9 Soil Pressure Less Than Allowable ACI Factored @ Toe = 2,303 psf Moment Allowable = 16,968.2 ACI Factored @ Heel = 484 psf Shear Actual psi= 35.9 Footing Shear @ Toe = 10.1 psi OK Shear Allowable psi= 75.0 Footing Shear @ Heel = 74.1 psi OK Wall Weight = 125.0 Allowable = 75.0 psi Rebar Depth 'd' in= 8.19 Sliding Calcs (Vertical Component Used) LAP SPLICE IF ABOVE in= 23.18 Lateral Sliding Force = 3,245.1 lbs LAP SPLICE IF BELOW in= less 100%Passive Force= - 45.1 lbs HOOK EMBED INTO FTG in= 8.57 less 100%Friction Force = - 3,555.6 lbs Lap splice above base reduced by stress ratio Hook embedment reduced by stress ratio Added Force Req'd = 0.0 lbs OK Masonry Data _ ....for 1.5: 1 Stability = 1,266.9 lbs NG fm psi= Fs psi= Solid Grouting = Use Half Stresses = Load Factors Modular Ratio'n' = Building Code IBC 2009,ACI Short Term Factor = Dead Load 1.200 Equiv.Solid Thick. = Live Load 1.600 Masonry Block Type = Medium Weight Earth, H 1.600 Masonry Design Method = ASD Wind,W 1.600 Concrete Data fc psi= 2,500.0 Seismic,E 1.000 Fy psi= 60,000.0 Footing Dimensions & Strengths I ' Footing Design Results Toe Width = 1.50 ft Toe Heel Heel Width = 7.25 Factored Pressure = 2,303 484 psf Total Footing Width = 8.75 Mu':Upward = 2,474 0 ft-# Footing Thickness = 14.00 in Mu':Downward = 236 1,318 ft-# Mu: Design = 2,237 1,318 ft-# Key Width = 0.00 in Actual 1-Way Shear = 10.06 74.12 psi Key Depth = 0.00 in Allow 1-Way Shear = 75.00 75.00 psi Key Distance from Toe = 0.00 ft Toe Reinforcing = #5 @ 18.00 in fc = 2,500 psi Fy = 60,000 psi Heel Reinforcing = #5 @ 10.00 in Footing Concrete Density = 150.00 pcf Key Reinforcing = None Spec'd Min.As% = 0.0018 Other Acceptable Sizes&Spacings Cover @ Top 2.00 @ Btm.= 3.00 in Toe: Not req'd,Mu<S*Fr Heel:Not req'd,Mu<S*Fr Key: No key defined Use menu item Settings>Printing&Title Block Title : 10'-0"Wall with seismic Page: to set these five lines of information Job# • Dsgnr: DNS Date: 20 JUN 2012 for your program. Description.... 10'-0"retained with seismic This Wall in File:g:\structural projects\projects\2012 projects\b1 RetainPro 10 (c)1987-2011, Build 10.12.1.13 License:KW-06059393 Cantilevered Retaining Wall Design Code: IBC 2009,ACI 318-08,ACI 530-08 License To:CORE ENGINEERING Summary of Overturning & Resisting Forces&Moments t OVERTURNING RESISTING Force Distance Moment Force Distance Moment Item lbs ft ft-# lbs ft ft-# Heel Active Pressure = 2,182.2 3.72 8,122.5 Soil Over Heel = 7,058.3 5.54 39,114.9 Surcharge over Heel = 142.1 5.58 793.5 Sloped Soil Over Heel = Surcharge Over Toe = Surcharge Over Heel = 256.7 5.54 1,422.4 Adjacent Footing Load = Adjacent Footing Load = Added Lateral Load = Axial Dead Load on Stem= Load @ Stem Above Soil= *Axial Live Load on Stem = Seismic Earth Load = 545.8 6.70 3,657.0 Soil Over Toe = 7,058.3 Seismic Stem Self Wt = 525.0 6.42 3,368.8 Surcharge Over Toe = Total 3,245.1 O.T.M. 14,979.2 Stem Weight(s) = 1,312.5 1.92 2,515.6 Earth @ Stem Transitions= = Footing Weight = 1,531.3 4.38 6,699.2 Resisting/Overturning Ratio = 3.32 Key Weight = Vertical Loads used for Soil Pressure= 10,158.8 lbs Vert.Component = Total= 10,158.8 lbs R.M.= 49,752.1 If seismic included the min.OTM and sliding *Axial live load NOT included in total displayed,or used for overturning ratios may be 1.1 per IBC'09, 1807.2.3. resistance,but is included for soil pressure calculation. DESIGNER NOTES: