Plans (29) 60 p/ko/Y- OO& 0
7 q,Lce f‘t) 1/1.2 ( 54 S
Archtte
HEAVY DUTY 2' X 2' SUSPENDED •\`V.4 o
// CEILING GRID RIVETED TO ��
CLOSURE ANGLE AT ATTACHED �.' /� •
3/ /4' SIDE- FREE TO SLIDE ON ANGLE
WITH 3/4 GAP ON UNATTACHED NOTE I:
;.':: //7,444
+
11 SIDE- REFER TO R.C.P.2/A3.1 INSTALL HEAVY DUTY METAL SUSPENSION
SYSTEM FOR ACOUSTICAL TILE FOR LAY-IN
2' PERIMETER
CONTINUOUS HORIZONTAL STRUT PANEL CEILINGS IN ACCORDANCE WITH OSSC
TO PREVENT SPREADING OF . 2' CLOSURE ANGLE SECTION 1613.1 AND ASCE 1-10,SECTION I3.5b. Rogers.
ROOF JOISTS RUNNERS ATTACHED TO _`
/
WALLIFURR-DOWN , `d
COMPRESSION STRUT / COMPRESSION STRUT SPACING NOTE 2:
/ NOT TO EXCEED 12'-0' O.C. IN DETAIL AT 2' PERIMETER CLOSURE ,
/ BOTH DIRECTIONS WITH THE FIRST SUPPORT ALL RECESSED OR DROP-IN LIGHT
/ POINT WITHIN 6'-0' FROM EACH
ANGLE FIXTURES AND GRILLES DIRECTLY FROM THE FIXTURE04//6"--SPLAY WiRf / PALL. COORDINATE LOCATION TO HOUSING TO THE STRUCTURE ABOVE WITH A MINIMUM CO,
OF FOUR 12-GAUGE WIRES LOCATED ONE AT EACH
AVOID CONFLICT WITH LIGHT CORNER FIXTURE SUPPORT WIRES MAY BE SLIGHTLY
/ FIXTURES. LOOSE TO ALLOW THE FIXTURE TOS SEAT IN THE GRID Kevin L. Cooper Architect
MAIN RUNNER 1 / SYSTEM.ATTACH LIGHT FIXTURES TO THE SUSPENDED
PANEL CEILING SYSTEM TO RESET 100 PERCENT OF FIXTURE Resource Design
2' PERIMETER CLOSURE COMPRESSION STRUT: WEIGHT ACTING IN ANY DIRECTION. 316 South 1st Street
• CROSS ANGLE- REFER TO
TEE SECTION AT STRUT SPACING ENLARGED DETAIL 3 5/8 (16 GA.)MTL.STUD ATTACHED Rogers,AR 72756
N.T.S. TO GRID AND STRUCTURE ABOVE NOTE 3: (479)633-8181 fax(479)633-9204
WITH (2)"8 SHEET MTL.SCREWS ATTACH SPLICES IN MAIN RUNNER WITH
12 GA VERTICAL HANGER MECHANICAL INTERLOCKING CONNECTORS: POP t------"1
WIRE + 4'-0' Off. EA.WAY - RIVETS,SCREWS, PINS,PLATES WITH BENT TABS
NOT MORE THAN 8' AWAY \ OR APPROVED EQUAL.CONNECTORS SHALL BE Eng Inner/Other:
FROM PERIMETER WALLS DESIGNED FOR 2X DESIGN LOAD (MIN 601ba.)
CROSS TEE .. NOTE 4:
LIGHT FIXTURES,ELECTRICAL WIRING SYSTEM
CONDUITS,LOW VOLTAGE WIRING COMPONENTS,
//\
COMMUNICATION,COMPUTER CABLE TRAYS AND
�" �`._� MECHANICAL SERVICES SHALL BE SUPPORTED
SPLAY WIRES: `��► CROSS INDEPENDENTLY OF THE SUSPENDED CEILING
(4) - 12GA WIRES IN 4d.11 TEE SYSTEM. gl*k3
DIRECTIONS. EACH WIRE AT Akio.
‘'Ill.'fgi%H'''''''''''-'N'Flli:AIN
45 DEGREES TO 2' MAX / ' CONSTRUCT EACH SUSPENDED CEILING
HORIZONTAL (MAX,TYP.) ► BRACE AT APPROPRIATE HANGER WIRES SPACE# K4
ALONG THE MAIN RUNNER BY ADDING: WASHINGTON SQUARE
COMPRESSION STRUT
• SPLAY WINS MALL
NOTE: TIGARD,
' , , , SECURELY ATTACH EACH CROSS TEE TO OREGON
NER THE MAIN RUNNER WITH A SADDLE TYPE
BRACE ASSEMBLY
CROSS TEE ATTACHMENT LOCKING PIN
NOT
N.T.S. E
MAIN RUNNER STRAND OFNUMBER 16 GAUGE TIE THAN WIRE
Q N.T.S.
0 CEILING BRACE IDE TAIL N.T.S.
1-fit
11974 fkt/r #gllp2i:,f5- aofo