Loading...
Report (27) P,5-020r c- 00u2— /0 3 3 0 xk2-10330 S( ) S C/L c- " March 5, 2015 RE: FIRE SPRINKLER SYSTEM Project Information Building Permit: FPS2015-00027 Construction Type: 2-B Tenant Name: MET Occupancy Type: E Address: 10330 SW Scholls Ferry Rd. Occupant Load: NA Area: 54,085 Sq. Ft. Stories: 2 The plan review was performed under the State of Oregon Structural Specialty Code (OSSC) 2014 edition; National Fire Protection Association, Standard 13 (NFPA 13) 2010 edition and the State of Oregon Fire Code (OFC) 2014 edition. GENERAL 1. A key box shall be installed in a location approved by the Fire Chief. The key box shall be of an approved type and shall contain keys to gain necessary access as required by the fire code official. Section 506.1 OFC. Please contact Tualatin Valley Fire & Rescue for key box information at 503-612-7010 2. A supply of spare sprinklers (never less than 6) shall be maintained on the premises so that any sprinklers that have operated or been damaged in any way can be promptly replaced. These sprinklers shall correspond to the types and temperature ratings of the sprinklers on the property. Sections 6.2.9.1 & 6.2.9.2 NFPA 13. 3. The spare sprinklers shall be kept in a cabinet located where temperatures will not exceed 100 degrees "F" at any time. A special sprinkler wrench shall be provided and kept in the sprinkler cabinet to be used in the removal and installation of sprinklers. Sections 6.2.9.3 & 6.2.9.6 NFPA 13. 4. The installing contractor shall identify a hydraulically designed sprinkler system with a permanently marked weatherproof metal or rigid plastic sign. Such signs shall be placed at the alarm valve, dry pipe valve, pre action valve, or deluge valve supplying the corresponding hydraulically designed area. 5. The clearance between the deflector and the top of storage shall be 18 inches or greater. Section 8.6.6.1 NFPA 13. The distance shall be increased to 36 inches for Large Drop sprinkler heads. Section 8.11.6 NFPA 13 6. Sprinklers shall be located a minimum of 4 inches from walls and spaced not less than 6 feet on center. Sections 8.6.3.3 & 8.6.3.4.1 NFPA 13. 7. Clearances shall be provided around all piping extending through platforms, foundations, walls and floors. The diameter of the hole shall be 2 inches larger than the penetrating pipe for pipe sizes 1 inch through 3 1/2 inches. The diameter of the hole shall be 4 inches larger than the penetrating pipe for pipe sizes 4 inches and larger 2 inches is required. Sections 9.3.4.1 & 9.3.4.2 NFPA 13. 8. All valves controlling the water supply for automatic sprinkler systems and all water flow monitoring devices shall be electrically monitored when the system serves more than 20 heads. Section 903.4 OFC 9. An approved audible sprinkler flow alarm shall be provided on the exterior of the building in an approved location. Such sprinkler water-flow devices shall be activated by water flow equivalent to the flow of a single sprinkler of the smallest orifice size installed in the system. Section 903.4.2 OFC 10.The system piping shall be braced to resist both lateral and longitudinal horizontal seismic loads to prevent vertical motion resulting from seismic loads. The structural components to which bracing is attached shall be determined to be capable of carrying the added applied seismic loads. Sway braces shall be designed to withstand forces in tension and compression. Bracing shall be attached directly to feed and cross mains. 11.The end sprinkler on a line shall be restrained against excessive vertical and lateral movement. 12.New sprinkler system piping shall be hydrostatically tested at 200 psi and shall maintain that pressure without loss for two hours. Where addition or modification is made to an existing system affecting less than 20 sprinklers this test need not be done. NFPA13 16.2.1.1 13.AII concealed spaces enclosed wholly or partly by exposed combustible construction shall be protected by sprinklers. 14.Dry systems shall be flowed through the remote inspectors test with the smallest sprinkler orifice used in the system. The time required for water flow to the inspectors test, the clapper trip time and the time it takes for the compressor to turn on shall be noted on the NFPA13 Completion Form. 15.Single interlock pre action systems shall be tested for operation of the detection device and dry pipe valve. Provisions shall be made for the manual operation of the detection system at locations requiring not more than 200ft. of travel. 16.The installing contractor shall complete and sign the appropriate contractor's material and test certificate found in NFPA13. Approved Plans: 1 set of approved plans, bearing the City of Tigard approval stamp, shall be maintained on the jobsite. The plans shall be available to the Building Division inspectors throughout all phases of construction. 106.4.2 OSSC When submitting revised drawings or additional information, please attach a copy of the enclosed City of Tigard, Letter of Transmittal. The letter of transmittal assists the City of Tigard in tracking and processing the documents. Respectfully, Dan Nelson, Senior Plans Examiner (503) 718-2436 dann@tigard-or.gov RECEIVED •' elFEB 2 6 2015 3Tual? ,�� AFP Systems,Inc. CITY OF TIGARD Automatic Fire Protection BUILDING DIVISION .� 19435 SW 129'"Avenue a atin,OR. 97062 (503)692-9284 �� (503)692-1186 fax 1 Submittal Project Name: MET Community Center 10330 SW Scholls Ferry Rd. Tigard, OR 97223 For TS Gray Construction, LLC 12705 SW Herman Rd. Tualatin, OR 97062 . Ok ..46.. `? , AFP Systems, Inc. VT Automatic Fire Protection E 19435 SW 129th Avenue � ���� �' Tualatin,OR. 97062 y� (503)692-9284 p (503)692-1186 fax Table of Contents A. Sprinkler Heads 1. Tyco TY3131 Brass Uprights /5.6K-Factor /'/z"NPT/ 155° 2. Tyco TY3231 Chrome Recessed Pendent / 5.6K-Factor /'/z"NPT/ 155° 3. Tyco TY3331 Brass Sidewall /5.6K-Factor /'/z"NPT/ 155° B. Valves 1. System Control Valve - Victaulic 705 Butterfly Valve with Tamper Switch C. Grooved Materials - Victaulic Grooved Fittings , .. ., - . fico Worldwide www t co-fire.com Fire Protection Contacts y Products Series TY-FRB — 2.8, 4.2, 5.6, and 8.0 K-Factor Upright, Pendent, and Recessed Pendent Sprinklers Quick Response, Standard Coverage General spheres.Although corrosion-resistant coated sprinklers have passed the ;- Description standard corrosion tests of the appli- cable approval agencies,the testing is - �jlt i c n The TYCO Series TY-FRB, 2.8, 4.2, not representative of all possible cor- � -_,::-.4., ti ,s 5.6, and 8.0 K-factor, Upright, Pen- rosive atmospheres. Consequently, it is recommended that the end user 1 dent, and Recessed Pendent Sprin- � ' � 1 I kiers described in this data she t r be consulted with respect to the suit- r e aeof these coatin s for ivenI quick response, standard coverage, ability 9 any 9 g decorative 3 mm glass bulb-type spray corrosive environment.The effects of ` y sprinklers designed for use in light or ambient temperature,concentration of t ordinary hazard,commercial occupan- chemicals,and gas/chemical velocity, cies such as banks, hotels,and shop- should be considered,as a minimum, ping malls. along with the corrosive nature of the chemical to which the sprinklers will be - The recessed version of the Series TY- exposed. FRB Pendent Sprinkler,where applica- ble is intended for use in areas with a An intermediate level of the Series TY- finished ceiling.This recessed pendent FRB Pendent Sprinklers is detailed "Li-, in Technical Data Sheet TFP356, and '', sprinkler uses one of the following: � Sprinkler Guards are detailed in Tech- r# • A two-piece Style 10(1/2 inch . P Y NPT) nical Data Sheet TFP780. � t or Style 40(3/4 inch NPT)Recessed i/f Escutcheon with 1/2 inch(12,7 mm)of NOTICE recessed adjustment or up to 3/4 inch 04t, • (191 mm)of total adjustment from the The Series TY-FRB, 2.8, 4.2, 5.6, ' r - flush pendent position,or a and 8.0 K-factor, Upright, Pendent, ,= • A two-piece Style 20(1/2 inch NPT) and Recessed Pendent Sprinklers described herein must be installed or Style 30(3/4 inch NPT)Recessed and maintained in compliance with Sprinkler Escutcheon with 1/4 inch(6,4 mm)of this document and with the applica- recessed adjustment or up to 1/2 inch ble standards of the National Fire Pro- Identification (12,7 mm)of total adjustment from the tection Association, in addition to the flush pendent position. standards of any authorities having Number (SIN) The adjustment provided by the jurisdiction.Failure to do so may impair Recessed Escutcheon reduces the the performance of these devices. TY1131: Upright 2.8K, 1/2"NPT accuracy to which the fixed pipe drops The owner is responsible for maintain- TY1231: Pendent 2.8K, 1/2"NPT to the sprinklers must be cut. ing their fire protection system and TY2131: Upright 4.2K,1/2"NPT Corrosion-resistant coatings, where devices in proper operating condition. TY2231: Pendent 4.2K,1/2"NPT applicable, are utilized to extend the The installing contractor or sprinkler T1l1 Upright 5.6K,1/2"NPT life of copper alloy sprinklers beyond manufacturer should be contacted with 'tY"1 1: Pendent 5.6K,1/2"NPT that which would otherwise be obtained any questions. TY4131: Upright 8.0K,3/4"NPT when exposed to corrosive atmo-pTY4231: Pendent 8.0K 3/4"NPT TY4831: Upright 8.0K,1/2"NPT • TY4931: Pendent 8.0K,1/2"NPT - IMPORTANT Always refer to Technical Data Sheet TFP700 for the "INSTALLER WARNING"that provides cautions with respect to handling and instal- lation of sprinkler systems and com- ponents. Improper handling and installation can permanently dam- age a sprinkler system or its compo- nents and cause the sprinkler to fail to operate in a fire situation or cause it to operate prematurely. Page 1 of 10 OCTOBER 2013 TFP171 • TFP171 Page 2 of 10 *Temperature rating ** Pipe thread connections per 1 - Frame 3 - Sealing 5 - Compression is indicated on ISO 7-1 can be provided on ESCUTCHEON 2 - Button Assembly Screw Deflector. special request. PLATE SEATING 4 - Bulb 6 - Deflector* SURFACE 7 - Bushing 7 7/16" (11,1 mm) I / 111,-- 2-1/4" � `, 3.14 11.1 I NOMINAL111 , 0L r • MAKE-IN (57,2 mm) I 2 MEN 2-3/16" 4 (55,6 mm) 10 1-9/16" . (39,71 mm) . )� 5 1/2"NPT** I WRENCH STYLE 10 or 20 2-7/8"(73,0 mm)DIA. - FLATS RECESSED UPRIGHT PENDENT ESCUTCHEON RECESSED PENDENT CROSS SECTION FIGURE 1 QUICK RESPONSE SERIES TY-FRB UPRIGHT(TY1131)AND PENDENT(TY1231)SPRINKLERS 2.8 K-FACTOR, 1/2 INCH NPT *Temperature rating ** Pipe thread connections per 1 - Frame 3 - Sealing 5 - Compression is indicated on ISO 7-1 can be provided on ESCUTCHEON 2 - Button Assembly Screw Deflector. special request. PLATE SEATING 4 - Bulb 6 - Deflector* . SURFACE - r 3 1 7/16" _11 I I / ■1' m_I11,1 mm) — NOMINAL I (55 6/mm) i $ MAKE IN I 4 (55 6/mm) 1—_---------- --- -- ----------_ 1-1/2" 1 -- ■ -•, (38,11I mm) .41 -- i �5 1 `ir 6* 1/2"NPT** I WRENCH STYLE 10 or 20 2-7/8"(73,0 mm)DIA. FLATS RECESSED UPRIGHT PENDENT ESCUTCHEON RECESSED PENDENT CROSS SECTION FIGURE 2 QUICK RESPONSE SERIES TY-FRB UPRIGHT(TY2131)AND PENDENT(TY2231)SPRINKLERS 4.2 K-FACTOR, 1/2 INCH NPT TFP171 Page 3 of 10 *Temperature rating ** Pipe thread connections per 1 - Frame 3 - Sealing 5 - Compression is indicated on ISO 7-1 can be provided on ESCUTCHEON 2 - Button Assembly Screw Deflector. special request. PLATE SEATING 4 - Bulb 6 - Deflector* SURFACE 1 10,017 7/16" i / — ___ r— g f� 3 (11,1 mm) ��1'=- A 1 NOMINAL /11 2-3/16" ��� 2 - MAKE-IN 1 (55,6 mm) '� Ai (55 6 mm 1-1/2",,, 4�� I 4 (38,1 mm) 6* 1/2"NPT** f WRENCH STYLE 10 or 20 2-7/8"(73,0 mm)DIA. - FLATS RECESSED UPRIGHT PENDENT ESCUTCHEON RECESSED PENDENT CROSS SECTION FIGURE 3 QUICK RESPONSE SERIES TY-FRB UPRIGHT(TY3131)AND PENDENT(TY3231)SPRINKLERS 5.6 K-FACTOR, 1/2 INCH NPT *Temperature rating ** Pipe thread connections per 1 - Frame 3 - Sealing 5 - Compression is indicated on ISO 7-1 can be provided on ESCUTCHEON 2 - Button Assembly Screw Deflector. special request. PLATE SEATING 4 - Bulb 6 - Deflector* SURFACE bill 1/2" I / '� (12,7 mm) i�=. 4 A 3 A NOMINAL 0—I I 2-5/16" PT�`� !` ^' !1 2 MAKE-IN (58,7 mm) A r ��� l 2-1/4" I 4 ,= 1 (57,2 mm) I (39,7- / m)6 -\ ----•----., 1 ----•---- la 6 * 3/4"NPT** t WRENCH STYLE 30 or 40 FLATS RECESSED 2-7/8"(73,0 mm)DIA. - UPRIGHT PENDENT ESCUTCHEON RECESSED PENDENT CROSS SECTION FIGURE 4 QUICK RESPONSE SERIES TY-FRB UPRIGHT(TY4131)AND PENDENT(TY4231)SPRINKLERS 8.0 K-FACTOR,3/4 INCH NPT TFP171 Page 4 of 10 CEILING PLATE 1 - Frame 5 - Compression 1 SEATING SURFACE 2 - Button Screw 1 3 - Sealing 6 - Deflector tTi-r -,-�c'� Assembly y 3 4 Bulb 1 7/16" 2-1/4" �� (11,1 mm) , (57,2 mm) %0 A 4 2 NOMINAL i MAKE-IN 1 * Temperature rating is �� 2-3/16" 1-9/16" 4 indicated on Deflector. (556 mm) (39,7 mm) . r�5 ** Pipe thread connections „___________. _��ir�.,,_ per ISO 7-1 can be 6 * provided on special 1/2"NPT** f WRENCH request. FLATS UPRIGHT PENDENT CROSS SECTION FIGURE 5 QUICK RESPONSE SERIES TY-FRB UPRIGHT(TY4831)AND PENDENT(TY4931)SPRINKLERS 8.0 K-FACTOR, 1/2 INCH NPT Technical Design torque can distort the sprinkler Inlet with consequent leakage or impairment Data Criteria of the sprinkler. The TYCO Series TY-FRB, 2.8, 4.2, Do not attempt to compensate for Approvals insufficient adjustment in the Escutch- UL and C-UL Listed 5.6, and 8.0 K-factor, Upright, Pen- eon Plate by under-or over-tightening FM, LPCB,and NYC Approved dent,and Recessed Pendent Sprinklers the sprinkler. Re-adjust the position of Refer to Table A and B for complete are intended for fire protection sys- the sprinkler fitting to suit. ; approval information including tems designed in accordance with the corrosion-resistant status. standard installation rules recognized Series TY-FRB Upright and Pendent by the applicable Listing or Approval Sprinklers Maximum Working Pressure agency (such as, UL Listing is based The Series TY-FRB Pendent and Refer to Table C. on the requirements of NFPA 13, and Upright Sprinklers must be installed FM Approval is based on the require- in accordance with the following Discharge Coefficient ments of FM's Loss Prevention Data instructions. K=2.8 GPM/psi1/2 (40,3 LPM/barl'2) Sheets). Only the Style 10, 20, 30, or Step1.Install Pendent sprinklers in the K=4.2 GPM/psi112 (60,5 LPM/barlI2) 40 Recessed Escutcheon,as applica- penPent position.Installupright sprin K=5.6 GPM/psi1i2 (80,6 LPM/bar1/2) ble,is to be used for recessed pendent klers in the upright position. K=8.0 GPM/psi112 (115,2 LPM/barli2) installations. Step 2. With pipe-thread sealant Temperature Rating Installation applied to the pipe threads, hand- Refer to Table A and B. tighten the sprinkler into the sprinkler The TYCO Series TY-FRB, 2.8, 4.2, fitting. Finishes 5.6,and 8.0 K-factor,Upright,Pendent, Sprinkler: Refer to Table D. Recessed and Recessed Pendent Sprinklersmust Step 3.Tighten the sprinkler into the Escutcheon:White Coated,Chrome be installed in accordance with this sprinkler fitting using only the W-Type 6 Plated,or Brass Plated. section. Sprinkler Wrench(Figure 14).With refer- ence to Figures 1 through 5,apply the Physical Characteristics General Instructions W-Type 6 Sprinkler Wrench to the sprin- Frame Bronze Do not install any bulb-type sprinkler if kler wrench flats. Button Brass/Copper the bulb is cracked or there is a loss Sealing Assembly Beryllium of liquid from the bulb.With the sprin- Series TY-FRB Recessed Pendent Nickel w/TEFLON kler held horizontally, a small air bub- Sprinklers Bulb Glass ble should be present. The diameter The Series TY-FRB Recessed Pendent Compression Screw Bronze of the air bubble is approximately 1/16 Sprinklers must be installed in accor- _ Deflector Copper/Bronze inch(1,6 mm)for the 135°F(57°C)and dance with the following instructions. Bushing(K=2.8) Bronze 3/32 inch(2,4 mm)for the 286°F(141°C) Step A.After installing the Style 10,20, _ Operation temperature ratings. 30, or 40 Mounting Plate, as applica- A leak-tight 1/2 inch NPT sprinkler joint ble,over the sprinkler threads and with The glass bulb contains a fluid that shold be obtained by applying a min- pipe-thread sealant applied to the pipe expands when exposed to heat.When imum to maximum torque of 7 to 14 threads,hand-tighten the sprinkler into the rated temperature is reached, the ft.-lbs. (9,5 to 19,0 Nm). A leak tight the sprinkler fitting. fluid expands sufficiently to shatter the 3/4 inch NPT sprinkler joint should be Step B.Tighten the sprinkler into the glass bulb, allowing the sprinkler to obtained with a torque of 10 to 20 ft.- sprinkler fitting using only the W-Type activate and water to flow. lbs.(13,4 to 26,8 Nm).Higher levels of 7 Recessed Sprinkler Wrench (Figure TFP171 Page 5 of 10 SPRINKLER FINISH(See Note 5) K BULB LIQUID NATURAL CHROME SIGNAL*** FACTOR TYPE TEMPERATURE COLOR BRASS PLATED WHITE 135°F(57°C) Orange PENDENT 155°F(68°C) Red (TY1231) and 175°F(79°C) Yellow 1,2,3,4 UPRIGHT (93°C) Green 200 F(93 (TY1131) ° ° 286°F(141°C) Blue 135°F(57°C) Orange 2.8 RECESSED 1 1/2"NPT PENDENT 55°F(68°C) Red (TY1231)* 175°F(79°C) Yellow Figure 6 200°F(93°C) Green• 1 2 4 135°F(57°C) Orange RECESSED PENDENT 155°F(68°C) Red (TY1231)** 175°F(79°C) Yellow Figure 7 200°F(93°C) Green 135°F(57°C) Orange PENDENT 155°F(68°C) Red (TY2231) and 175°F(79°C) Yellow UPRIGHT (TY2131) 200°F(93°C) Green 286°F(141°C) Blue 135°F(57°C) Orange 4.2 RECESSED ° ° 155F 68C 1/2"NPT PENDENT ( ) Red 1,2 (TY2231)* 175°F(79°C) Yellow Figure 8 200°F(93°C) Green 135°F(57°C) Orange RECESSED ) PENDENT (155°F 68°C Red (TY2231)** 175°F(79°C) Yellow Figure 9 200°F(93°C) Green NOTES: 1. Listed by Underwriters Laboratories,Inc.,(UL)as Quick Response Sprinklers. 2. Listed by Underwriters Laboratories,Inc.,for use in Canada(C-UL)as Quick Response Sprinklers. 3. Approved by Factory Mutual Research Corporation(FM)as Quick Response Sprinklers. 4. Approved by the City of New York under MEA 354-01-E. 5. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed,the sprinklers are UL and C-UL Listed as Corrosion-Resistant Sprinklers. Installed with Style 10(1/2"NPT)or Style 40(3/4"NPT)3/4"Total Adjustment Recessed Escutcheon,as applicable. "Installed with Style 20(1/2"NPT)or Style 30(3/4"NPT)1/2"Total Adjustment Recessed Escutcheon,as applicable. "*"Frame and Deflector only.Listings and approvals apply to color(Special Order). N/A:Not Available TABLE A LABORATORY LISTINGS AND APPROVALS FOR 2.8 AND 4.2 K-FACTOR SPRINKLERS 15). With reference to Figures 1 to 4, apply the W-Type 7 Recessed Sprinkler Wrench to the sprinkler wrench flats. Step C. After ceiling installation and finishing,slide on the Style 10,20,30, or 40 Closure over the Series TY-FRB Sprinkler and push the Closure over the Mounting Plate until its flange comes in contact with the ceiling. TFP171 Page 6 of 10 SPRINKLER FINISH(See Note 8) K TYPE TEMPERATURE BULB LIQUID NATURAL CHROME SIGNAL*** LEAD FACTOR COLOR BRASS PLATED WHITE COATED 135°F(57°C) Orange PENDENT (TY3231) 155°F(68°C) Red and 175°F(79°C) Yellow 1,2,3,4,5,6,7 1,2,3,5 UPRIGHT 200°F(93°C) Green (TY3131) 286°F(141°C) Blue 135°F(57°C) Orange RECESSED 155°F(68°C) Red 5.6 PENDENT 175°F(79°C) Yellow 1,2,4,5 N/A 1/2"NPT (TY3231) Figure 10 200°F(93°C) Green 286°F(141°C) Blue 135°F(57°C) Orange RECESSED 155°F(68°C) Red PENDENT 175°F(79°C) Yellow 1,2,3,4,5 N/A (TY3231)** Figure 11 200°F(93°C) Green 286°F(141°C) Blue 135°F(57°C) Orange PENDENT (TY4231) 155°F(68°C) Red and 175°F(79°C) Yellow 1,2,3,4,5,6,7 1,2,5 UPRIGHT 200°F(93°C) Green (TY4131) 286°F(141°C) Blue 135°F(57°C) Orange RECESSED 155°F(68°C) Red 8.0 PENDENT 175°F(79°C) Yellow 1,2,5 N/A 3/4"NPT (TY4231)* Figure 12 200°F(93°C) Green 286°F(141°C) Blue 135°F(57°C) Orange RECESSED 155°F(68°C) Red PENDENT 175°F(79°C) Yellow 1,2,3,5 N/A (TY4231)** - Figure 13 200°F(93°C) Green 286°F(141°C) Blue 135°F(57°C) Orange PENDENT 155°F(68°C) Red 8.0 (TY4931) 1/2"NPT and 175°F(79°C) Yellow 1,2,4,5,6 1,2,5 UPRIGHT 200°F(93°C) Green (TY4831) 286°F(141°C) Blue NOTES: 1. Listed by Underwriters Laboratories,Inc.,(UL)as Quick Response Sprinklers. 2. Listed by Underwriters Laboratories,Inc.,for use in Canada(C-UL)as Quick Response Sprinklers. 3. Approved by Factory Mutual Research Corporation(FM)as Quick Response Sprinklers. 4. Approved by the Loss Prevention Certification Board(LPCB Ref.No.007k/04)as Quick Response Sprinklers.However,LPCB does not rate the thermal sensitivity of recessed sprinklers. 5. Approved by the City of New York under.MEA 354-01-E. 6. VdS Approved(For details,contact Tyco Fire Suppression&Building Products,Enschede,Netherlands,Tel.31-53-428-4444/Fax 31-53-428-3377.) 7. Approved by the Loss Prevention Certification Board(LPCB Ref.No.094a/06)as Quick Response Sprinklers. 8. Where Polyester Coated and Lead-Coated Sprinklers are noted to be UL and C-UL Listed,the sprinklers are UL and C-UL Listed as Corrosion-Resistant Sprinklers.Where Lead-Coated Sprinklers are noted to be FM Approved,the sprinklers are FM Approved as a Corrosion-Resistant Sprinklers. Installed with Style 10(1/2"NPT)or Style 40(3/4"NPT)3/4"Total Adjustment Recessed Escutcheon,as applicable. "Installed with Style 20(1/2"NPT)or Style 30(3/4"NPT)1/2"Total Adjustment Recessed Escutcheon,as applicable. '"`Frame and Deflector only.Listings and approvals apply to color(Special Order). N/A:Not Available TABLE B LABORATORY LISTINGS AND APPROVALS FOR 5.6 AND 8.0 K-FACTOR SPRINKLERS TFP171 Page 7 of 10 SPRINKLER FINISH K TYPE NATURAL CHROME SIGNAL LEAD FACTOR BRASS PLATED WHITE COATED PENDENT(TY1231) and 2.8 UPRIGHT(TY1131) 175 PSI(12,1 BAR) N/A 1/2"NPT RECESSED PENDENT(TY1231) PENDENT(TY2231)and 4.2 UPRIGHT(TY2131) 175 PSI(12,1 BAR) N/A 1/2"NPT RECESSED PENDENT(TY2231) PENDENT(TY3231) 175 PSI UPRIGHT(TY3131) 250 PSI(17,2 BAR) (12,1 BAR) 5.6 OR 175 PSI(12,1 BAR) 1/2"NPT (SEE NOTE 1) RECESSED N/A PENDENT(TY3231) PENDENT(TY4231) 175 PSI and (12,1 BAR) UPRIGHT(TY4131) 8.0 175 PSI(12,1 BAR) . 3/4"NPT RECESSED N/A PENDENT(TY4231) 8 0 PENDENT(TY4931) 175 PSI and • 1/2"NPT UPRIGHT(TY4831) 175 PSI(12,1 BAR) (12,1 BAR) NOTES: 1. The maximum working pressure of 250 psi(17,2 bar)only applies to the Listing by Underwriters Laboratories Inc.(UL);the Listing by Underwriters Laboratories,Inc.for use in Canada(C-UL);and,the Approval by the City of New York. TABLE C MAXIMUM WORKING PRESSURE Care and corrosive products of combustion, but tion Service in accordance with local have not operated,should be replaced requirements and/or national codes. Maintenance if they cannot be completely cleaned by wiping the sprinkler with a cloth or Care must be exercised to avoid dam- The TYCO Series TY-FRB must be by brushing it with a soft bristle brush. age to the sprinklers -before, during, and after installation. Sprinklers dam- maintained and serviced in accordance Care must be exercised to avoid dam- aged by dropping, striking, wrench with this section. age to the sprinklers- before, during, twist/slippage, or the like, must be Before closing a fire protection system and after installation.Sprinklers dam- replaced. Also, replace any sprinkler main control valve for maintenance aged by dropping, striking, wrench that has a cracked bulb or that has lost work on the fire protection system twist/slippage, or the like, must be liquid from its bulb. (Ref. Installation that it controls, obtain permission to replaced. Also, replace any sprinkler Section). shut down the affected fire protection that has a cracked bulb or that has lost systems from the proper authorities liquid from its bulb. (Ref. Installation Initial and frequent visual inspections of and notify all personnel who may be Section.) random samples are recommended for affected by this action. The owner is responsible for the corrosion-resistant sprinklers to verify • P the integrity of the corrosion-resistant Absence of the outer piece of an inspection,testing,and maintenance of material of construction. Thereafter, escutcheon, which is used to cover their fire protection system and devices annual inspections per NFPA 25 should a clearance hole, can delay sprinkler in compliance with this document, as suffice. operation in a fire situation. well as with the applicable standards of the National Fire Protection Associa- Inspections of corrosion-resistant Sprinklers which are found to be leak- tion(e.g., NFPA 25), in addition to the sprinklers are recommended at close ing or exhibiting visible signs of corro- standards of any other authorities hav- range, instead of from the floor level sion must be replaced. ing jurisdiction. Contact the installing per NFPA. Inspection at close range Automatic sprinklers must never be contractor or sprinkler manufacturer can better determine the exact sprin- painted, plated, coated, or other- regarding any questions. kler condition and ritthe long-term integ- painted, altered after leaving the factory. Automatic sprinkler systems are rec- whichy f the corrosion-resistantedby material,ose Modified sprinklers must be replaced. ommended to be inspected, tested, can be affected the corrosive Sprinklers that have been exposed to and maintained by a qualified Inspec- conditions present. TFP171 Page 8 of 10 2-7/8"DIA. .- -. 2-7/8"DIA. - 5/8±1/4" (73,0 mm) 3/4"(19,1 mm) 1/2±1/8" (73,0 mm) 1/2"(12,7 mm) (15,9±6,4 mm) 1/4"(6,4 mm) (12,7±3,2 mm) 2-1/4"DIA. 1/4"(6,4 mm) 2-1/4"DIA. / FACE OF (57,2 mm) MOUNTING / FACE OF (57,2 mm) --..- / y MOUNTING SPRINKLER PLATE SPRINKLER PLATE FITTING FITTING / 2m / 1/8" (3,2 mm) ( mm) • 17777 - r . / _, _ MOUNTING j� SURFACE it f SURFACE , ...77/""!-V,..,.. ii•��. CLOSURE SERIES 1-5/16"(33,3 mm) CLOSURE SERIES 1-5/16"(33,3 mm) TY-FRB 13/16"(20,6 mm) TY-FRB 1-1/16"(27,0 mm) FIGURE 6 FIGURE 7 SERIES TY-FRB RECESSED PENDENT SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON 2.8 K-FACTOR, 1/2 INCH NPT Z8 K-FACTOR, 1/2 INCH NPT 2-7/8"DIA. _ _ 2-7/8"DIA. - 5/8±1/4" (73,0 mm) 3/4"(19,1 mm) 1/2±1/8 (73,0 mm) 1/2"(12,7 mm) _' (15,9±6,4 mm) 1/4"(6,4 mm) (12,7±3,2 mm) 1/4" 2-1/4"DIA. 2-1/4"DIA. (6,4 mm) / FACE OF (57,2 mm) MOUNTING / FACE OF (57,2 mm) 1 SPRINKLER MOUNTING PLATE SPRINKLER PLATE FITTING FITTING / 1/8" / 1/8" / 1 'i (3,2 mm) (3,2 mm) r / •1 \ _14 ---=---=---------- 1__• P777>' 7zat 11011 r '/ OR-' j_ \ 11 f _ ',I-: MOUNTING „ MOUNTING SURFACE SURFACE ._ • .. __ • __. CLOSURE SERIES 1-1/4"(31,8 mm) CLOSURE SERIES 1-1/4"(31,8 mm) TY-FRB 3/4"(19,1 mm) TY-FRB 1"(25,4 mm) FIGURE 8 FIGURE 9 SERIES TY-FRB RECESSED PENDENT SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON 4.2 K-FACTOR, 1/2 INCH NPT 4.2 K-FACTOR, 1/2 INCH NPT TFP171 Page 9 of 10 2-7/8"DIA. _ _ 2-7/8"DIA. 5/811/4" (73,0 mm) 3/4"(19,1 mm) (73,0 mm) (15,/8±1/9±6,4 mm) 1/2±1/8" 1/2"(12,7 mm) f- 2-1/4"DIA. 1/4"(6,4 mm) (12,713,2 mm) 1/4"(6,4 2-1/4"DIA. mm) / FACE OF (57,2 mm) / f- (57,2 mm) -y SPRINKLER MOUNTING FACE OF MOUNTING FITTING PLATE SPRINKLER I TI G PLATE / 1/8" 1/8" �,� (3,2 mm) �i (3,2 mm) 2-4 zi. its. __ MI f \ -RJMOUNTING ,,'MOUNTING ii II SURFACE SURFACE - :-„- , - _ i CLOSURE SERIES 1-1/4"(31,8 mm) CLOSURE SERIES 1-1/4"(31,8 mm) TY-FRB 3/4"(19,1 mm) TY-FRB 1"(25,4 mm) FIGURE 10 FIGURE 11 SERIES TY-FRB RECESSED PENDENT SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON 5.6 K-FACTOR, 1/2 INCH NPT 5.6 K-FACTOR, 1/2 INCH NPT 2-7/8"DIA. - 2-7/8"DIA. 5/8±1/4" (73,0 mm) 3/4"(19,1 mm) 1/2±1/8" (73,0 mm) _ 1/2"(12,7 mm) (15,9±6,4 mm) 2-1/4"DIA. 1/4"(6,4 mm) (12,7±3,2 mm) 2-1/4"DIA. 1/4"(6,4 mm) / FACE OF (57,2 mm) MOUNTING / FACE OF (57,2 mm) -y MOUNTING SPRINKLER PLATE SPRINKLER PLATE FITTING FITTING / 1/8" 1/8" (3,2 mm) / (3,2 mm) } \ 4L/7 �,1- MOUNTING IIS MOUNTING I( SURFACE SURFACE �. , . CLOSURE SERIES 1-5/16"(33,3 mm) CLOSURE SERIES 1-5/16"(33,3 mm) TY-FRB 13/16"(20,6 mm) TY-FRB 1-1/16"(27,0 mm) FIGURE 12 FIGURE 13 SERIES TY-FRB RECESSED PENDENT SERIES TY-FRB RECESSED PENDENT WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 40 RECESSED ESCUTCHEON STYLE 30 RECESSED ESCUTCHEON 8.0 K-FACTOR,3/4 INCH NPT 8.0 K-FACTOR,3/4 INCH NPT Gl WRENCH RECESS WRENCH RECESS ,../1"-w. (END"A"USED FOR e'!'� 1/2"NPT MODELS) . t WRENCH RECESS (END"B"USED FOR 44,...., 3/4"NPT MODELS) PUSH WRENCH IN TO ENSURE ENGAGEMENT WITH SPRINKLER WRENCHING AREA FIGURE 14 FIGURE 15 W-TYPE 6 SPRINKLER W-TYPE 7 RECESSED WRENCH SPRINKLER WRENCH TFP171 Page 10 of 10 P/N 57 - XXX - X - XXX SIN SPRINKLER TEMPERATURE FINISH RATINGS 330 2.8K UPRIGHT(1/2"NPT) TY1131 1 NATURAL BRASS 135 135°F(57°C) 331 2.8K PENDENT(1/2"NPT) TY1231 3 PURE WHITE 155 155°F(68°C) (RAL9010)* 340 4.2K UPRIGHT(1/2"NPT) TY2131 4 SIGNAL WHITE 175 175°F(79°C) (RAL9003) • 341 4.2K PENDENT(1/2"NPT) TY2231 5 JET BLACK 200 200°F(93°C) (RAL9005)** • 370 5.6K UPRIGHT(1/2"NPT) TY3131 7 LEAD COATED 286 286°F(141°C) 371 5.6K PENDENT(1/2"NPT) TY3231 9 CHROME PLATED 390 8.0K UPRIGHT(3/4"NPT) TY4131 *Eastern Hemisphere sales only. **Available in only 2.8K,4.2K,and 391 8.0K PENDENT(3/4"NPT) TY4231 8.0K,155°F(68°C)and 200°F(93°C); requires lead time to manufacture. 360 8.0K UPRIGHT(1/2"NPT) TY4831* 361 8.0K PENDENT(1/2"NPT) TY4931* TABLE D SERIES TY-FRB PENDENT AND UPRIGHT SPRINKLERS PART NUMBER SELECTION Ordering Procedure Contact your local distributor for availability. When placing an order, indicate the full product name and Part Number(P/N). Sprinkler Assemblies with NPT Thread Connections Specify: Series TY-FRB(Specify SIN), (specify K-factor),(specify Pendent or Upright) Sprinkler (specify) tempera- ture rating, (specify) finish or coating, P/N(specify from Table D) Recessed Escutcheon: Specify: Style (10, 20, 30, or 40) Recessed Escutcheon with (specify*) finish, P/N(specify*) Sprinkler Wrench Specify: W-Type 6 Sprinkler Wrench, P/N 56-000-6-387 Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 *Refer to Technical Data Sheet TFP770 GLOBAL HEADQUARTERS 11400 Pennbrook Parkway,Lansdale,PA 194461 Telephone+1-215-362-0700 Copyright®2013 Tyco Fire Products,LP. All rights reserved. two TEFLON is trademark of The DuPont Corporation. �f Fire Protection Products `[ICO Worldwide www t co-fire.co Fire Protection Contacts y n' Products Series TY-FRB — 5.6 K-factor Horizontal and Vertical Sidewall Sprinklers Quick Response, Standard Coverage General tamed when exposed to corrosive at- mospheres. Although corrosion resis- Description tant coated sprinklers have passed the standard corrosion tests of the appli- The Series TY-FRB, 5.6 K-factor, Hor cable approval agencies,the testing is izontal and Vertical Sidewall Sprin not representative of all possible cor klers described in this data sheet rosive atmospheres. Consequently, it (.111* r",-01111, are quick response -standard cover- is recommended that the end user be f consulted with respect to the suitabil- I / -i age, decorative 3 mm glass bulb type ity of these coatings for any given cor- " spray sprinklers designed for use in rosive environment.The effects of am- light "` light and ordinary hazard, nksbient temperature, concentration of cial occupancies such as banks,, ho ho- chemicals, and gas/chemical velocity, -''// tels,shopping malls,etc.They are de should be considered, as a minimum, signed for installation along a wall or along with the corrosive nature of the the side of a beam and just beneath a chemical to which the sprinklers will smooth ceiling.Sidewall sprinklers are be exposed. commonly used instead of pendent or upright sprinklers due to aesthetics or building construction considerations, NOTICE - where piping across the ceiling is not The Series TY-FRB Sprinklers de- desirable. scribed herein must be installed and The recessed version of the Series it maintained in compliance with this TY-FRB Horizontal Sidewall Sprin- document, as well as with the appli- kler is intended for use in areas with cable standards of the National Fire a finished wall. It uses a two-piece Protection Association, in addition to Style 10 Recessed Escutcheon with the standards of any other authorities 1/2 inch(12,7 mm)of recessed adjust- having jurisdiction. Failure to do so ment or up to 3/4 inch(19,1 mm)of to- may impair the performance of these tal adjustment from the flush sidewall devices. position, or a two-piece Style 20 Re- The owner is responsible for main- 1 cessed Escutcheon with 1/4 inch (6,4 taming their fire protection system mm) of recessed adjustment or up to and devices in proper operating con- . 1/2 inch (12,7 mm)of total adjustment dition. Contact the installing contrac- from the flush sidewall position. The tor or sprinkler manufacturer with any adjustment provided by the Recessed questions. Technical Escutcheon reduces the accuracy to which the fixed pipe nipples to the Sprinkler Data sprinklers must be cut. p Corrosion resistant coatings, where Identification Approvals applicable, are utilized to extend the UL and C-UL Listed. life of copper alloy sprinklers beyond Numbers FM, LPCB,and NYC Approved. that which would otherwise be ob- (Refer to Table A for complete approv- TY3331 Horizontal al information including corrosion re- TY3431 Vertical sistant status.) . IMPORTANT Always refer to Technical Data Maximum Working Pressure Sheet TFP700 for the "INSTALLER Refer to Table B. ' WARNING" that provides cau- Discharge Coefficient tions with respect to handling K=5.6 GPM/psi1i2(80,6 LPM/bar1/2) and installation of sprinkler sys- tems and components. Improp- Temperature Ratings er handling and installation can Refer to Table A. permanently damage a sprin- Finishes kler system or its components Sprinkler:Refer to Table C. and cause the sprinkler to fail Recessed Escutcheon:Signal or Pure to operate in a fire situation or cause White,Jet Black,Chrome lated ,or it to operate prematurely. Brass Plated. Page 1 of 6 FEBRUARY 2014 TFP176 TFP176 Page 2 of 6 DEFLECTOR Installation 1 - Frame 2 - Button HAT 5 0060.6160 The Series TY-FRB, 5.6 K-factor, Hori- 3 - Sealing _dr. zontal and Vertical Sidewall Sprinklers Assembly I must be installed in accordance with 4 - Bulb r"" /ATOM. this section. 5 - Compression General Instructions Screw / Do not install any bulb type sprin- 6 Deflector* 6* 4 2 3 1 kler if the bulb is cracked or there is a loss of liquid from the bulb.With the 9/16" WRENCH 1/2"** sprinkler held horizontally, a small air (14,3 mm) FLATS NPT bubble should be present. The diam- eter of the air bubble is approximately — 1111111\— -aall—,\ 1/16 inch(1,6 mm)for the 135°F(57°C) / to 3/32 inch (2,4 mm) for the 286°F O lillraidillei I (141°C)temperature ratings. ' .,... / , �� A leak tight 1/2 inch NPT sprinkler joint � should be obtained with a torque of 7 1-13/16" 7/16" to 14 ft.-lbs. (9,5 to 19,0 Nm). Higher (46,0 mm) (11,1 mm) f levels of torque may distort the sprin- NOMINAL kler and cause leakage or impairment CENTERLINE MAKE-IN of the sprinkler. OF SPRINKLER WATERWAY Do not attempt to make-up for insuf- 1-1/2" ficient adjustment in the escutcheon —(38,1 mm)y plate by under-or over-tightening the *Temperature rating sprinkler. Readjust the position of the is indicated on2-3/16" - sprinkler fitting to suit. Deflector. r (55 ,6 mm) ESCUTCHEON Series TY-FRB Horizontal and STYLE I _ PLATE SEATING Vertical Sidewall Sprinkler ** Pipe thread 10 or 20 Installation connections per RECESSED SURFACE ISO 7-1 can be ESCUTCHEON The Series TY-FRB Horizontal and provided on � Vertical Sidewall Sprinklers must be special request. �� installed in accordance with the fol- 01„ lowing instructions. 2-7/8"DIA. Step 1. Horizontal sidewall sprinklers (73,0 mm) ireitialliffill are to be installed in the horizontal po- sition with their centerline of waterway perpendicular to the back wall and parallel to the ceiling.The word"TOP" on the Deflector is to face towards the ceiling. Vertical sidewall sprinklers are to be FIGURE 1 installed in the pendent or upright po- 5.6 K-FACTOR QUICK RESPONSE sition with the arrow on the Deflector SERIES TY-FRB HORIZONTAL SIDEWALL(TY3331)SPRINKLERS pointing away from the wall. Ph sical Characteristics Step 2. With pipe thread sealant ap- y Design plied to the pipe threads, hand tighten Frame Bronze the sprinkler into the sprinkler fitting. Button Brass/Copper Criteria Sealing Assembly Beryllium Nickel w/ Step 3. Tighten the sprinkler into the TEFLON sprinkler fitting using only the W-Type Bulb Glass The Series TY-FRB,5.6 K-factor, Hori- 6 Sprinkler Wrench (Ref. Figure 5), Compression Screw Bronze zontal and Vertical Sidewall Sprinklers With reference to Figure 1 or 2,the W- HSW Deflector Bronze are intended for fire protection sys- Type 6 Sprinkler Wrench is to be ap- VSW Deflector Copper tems designed in accordance with the plied to the wrench flats. standard installation rules recognized Operation by the applicable Listing or Approval agency (e.g., UL Listing is based on The glass bulb contains a fluid which the requirements of NFPA 13, and FM expands when exposed to heat.When Approval is based on the requirements the rated temperature is reached, the of FM's Loss Prevention Data Sheets). fluid expands sufficiently to shatter Only the Style 10 or 20 Recessed Es- the glass bulb, allowing the sprinkler cutcheon, as applicable, is to be used to activate and water to flow. for recessed horizontal installations. TFP176 Page 3 of 6 Series TY-FRB Recessed *Temperature ** Pipe thread 1 - Frame 4 - Bulb 7 - Ejection Horizontal Sidewall Sprinkler rating is connections 2 - Button 5 - Compression Spring Installation indicated on per ISO 7-1 can 3 - Sealing Screw The Series TY-FRB Recessed Hari- Deflector. be provided on Assembly 6 - Deflector* zontal Sidewall Sprinklers must be special request. installed in accordance with this , section. ARROW MUST ` POINT AWAY �� Step A. Recessed horizontal sidewall 7/16" FROM AND BE \ sprinklers are to be installed in the ESCUTCHEON (11,1 mm) PERPENDICULAR O p horizontal position with their center- PLATE SEATING NOMINAL TO THE BACK 4 line of waterway perpendicular to the SURFACE ** MAKE-IN WALL SURFACE back wall and parallel to the ceiling. NPT The word "TOP"on the Deflector is to 6* face towards the ceiling. I L f���-Z ••_iey;\ Step B.After installing the Style 10 or ��� FLOW��r�5 20 Mounting Plate over the sprinkler threads,hand tighten the sprinkler into 2-3/16" dl Itsiroi 2-3/16" I 4 the sprinkler fitting. (55,6 mm) 1 (55,6 mm) j v Step C. Tighten the sprinkler into the 1-1/2" \ Iv ; 2 sprinkler fitting using only the WType (38,1 mm) WRENCH/'I7 Recessed Sprinkler Wrench (Ref. FLATS 7 3 Figure 6). With reference to Figure z���s 1, the W-Type 7 Recessed Sprinkler 1 Wrench is to be applied to the sprin- SHOWN SHOWN CROSS kler wrench flats. PENDENT UPRIGHT SECTION • Step D. After the ceiling has been in- FIGURE 2 stalled or the finish coat has been ap- 5.6 K-FACTOR QUICK RESPONSE plied, slide on the Style 10 or 20 Clo SERIES TY-FRB VERTICAL SIDEWALL(TY3431)SPRINKLERS sure over the Series TY-FRB Sprinkler and push the Closure over the Mount- ing Plate until its flange comes in con- if they cannot be completely cleaned The owner is responsible for the in- tact with the ceiling. by wiping the sprinkler with a cloth or spection, testing, and maintenance by brushing it with a soft bristle brush. of their fire protection system and de- are and Care must be exercised to avoid dam vices in compliance with this docu- ment, as well as with theapplicable age to the sprinklers before, during, Maintenance and after installation. Sprinklers dam- standards of the National Fire Pro- aged by dropping, striking, wrench tection Association (e.g., NFPA 25), in The Series TY-FRB,5.6 K-factor, Hori- twist/slippage, or the like, must be addition to the standards of any oth- zontal and Vertical Sidewall Sprinklers replaced. Also, replace any sprinkler er authorities having jurisdiction. The must be maintained and serviced in that has a cracked bulb or that has installing contractor or sprinkler man- accordance with this section. lost liquid from its bulb. (Ref. Installa- ufacturer should be contacted relative tion Section to any questions. Before closing a fire protection sys- )• tem main control valve for mainte- The owner must assure that the sprin- It is recommended that automatic nance work on the fire protection sys- klers are not used for hanging any ob- sprinkler systems be inspected, test- tem that it controls,permission to shut jects and that the sprinklers are only ed, and maintained by a qualified In- down the affected fire n Y5 cleaned by means of gently dustingspectionrequirements and/orrvice in an ternce must be obtained from om the national prop- local with a feather duster; otherwise, non- codes. er authorities and all personnel who operation in the event of a fire or inad- may be affected by this action must vertent operation may result. be notified. Frequent visual inspections are rec- Absence of an escutcheon, which is ommended to be initially performed used to cover a clearance hole, may for corrosion resistant coated sprin- delay the time to sprinkler operation in klers, after the installation has been • afire situation. completed,to verify the integrity of the Sprinklers that are found to be leaking corrosion resistant coating. Thereaf- or exhibiting visible signs of corrosion ter, annual inspections per NFPA 25 must be replaced. should suffice; however, instead of in- • specting from the floor level,a random Automatic sprinklers must never be sampling of close-up visual inspec- painted, plated, coated or other- tions should be made, so as to better wise altered after leaving the factory.y determine the exact sprinklerrinkler condi- Modified sprinklers must be replaced. tion and the longterm integrity of the Sprinklers that have been exposed to y corrosion resistant coating, as it may Y corrosive products of combustion,but be affected by the corrosive condi- have not operated,should be replaced tions present. TFP176 Page 4 of 6 5/8±1/4" G, (15,9±6,4 mm) MOUNTING FACE OF WRENCH RECESS SURFACE --- SPRINKLER (END"A"USED FOR FITTING 1/2"NPT MODELS) A t FIGURE 5 CLOSURE A - W-TYPE 6 SPRINKLER WRENCH ,10= 2-7/8"DIA. SERIES real (73,0 mm) TY FRB ���/11III (57 2-1/4,2 mm) WRENCH RECESS 11 ma MOUNTING 1 �1 PLATE Ir � / r � � y 1/8" YYY I (3,2 mm) 1-1/4"(31,8 mm) _ _ I 3/4"(19,1 mm) PUSH WRENCH 3/4"(19,1 mm) r 1/4"(6,4 mm) IN TO ENSURE ENGAGEMENT FIGURE 3 WITH SPRINKLER SERIES TY-FRB RECESSED HORIZONTAL SIDEWALL SPRINKLER WRENCHING AREA . WITH TWO-PIECE 3/4 INCH TOTAL ADJUSTMENT FIGURE 6 STYLE 10 RECESSED ESCUTCHEON W-TYPE 7 RECESSED SPRINKLER WRENCH _ 1/2±1/8" y (12,7±3,2 mm) MOUNTING FACE OF SURFACE --- SPRINKLER FITTING A CLOSURE A �_ 2-7/8"DIA. (73,0 mm) SERIES 701111 2-1/4"DIA. TY FRB t lull (57,2 mm) �`I MOUNTING ! PLATE I '� /1 — I 1/8" I (3,2 mm) 1-1/4"(31,8 mm) I 1/2"(12,7 mm) 1"(25,4 mm) r 1/4"(6,4 mm) FIGURE 4 SERIES TY-FRB RECESSED HORIZONTAL SIDEWALL SPRINKLER WITH TWO-PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20 RECESSED ESCUTCHEON TFP176 Page 5 of 6 SPRINKLER FINISH(See Note 11) K TYPE TEMP. BULB NATURAL CHROME LIQUID BRASS PLATED POLYESTER"' LEAD COATED 135°F(57°C) Orange j HORIZ. 155°F(68°C) Red SIDEWALL 175°F(79°C) Yellow 1,2,3,4,9,10 1,2,3,9 1,2,3,9 (TY3331) 200°F(93°C) Green 286°F(141°C) Blue 5.6 RECESSED 135°F(57°C) Orange 1/2" HORIZ. 155°F(68°C) Red NPT SIDEWALL 175°F(79°C) Yellow 1,2,4,9,10 1,2,9 N/A (TY3331)* Figure 3 200°F(93°C) Green RECESSED 135°F(57°C) Orange HORIZ. 155°F(68°C) Red SIDEWALL 1,2,3,4,9 N/A (TY3331)** 175°F(79°C) Yellow Figure 4 200°F(93°C) Green VERTICAL 135°F(57°C) Orange SIDEWALL 155°F(68°C) Red 5.6 (TY3431) 1/2" Installed 175°F(79°C) Yellow 5,6,7,8,9 5,6,7,9 NPT Pendent or 200°F(93°C) Green Upright P86°F(141°C) Blue NOTES: 1. Listed by Underwriters Laboratories,Inc.(UL)as Quick Response Sprinklers for use in Light and Ordinary Hazard Occupancies at a 4 to 12 inch(100 to 300 mm)top of deflector to ceiling distance. 2. Listed by Underwriters Laboratories Inc.for use in Canada(C-UL)as Quick Response Sprinklers for use in Light and Ordinary Hazard Occupancies at a 4 to 12 inch(100 to 300 mm)top of deflector to ceiling distance. 3. Approved by Factory Mutual Research Corporation(FM)as Quick Response Sprinklers for use in Light Hazard Occupancies at a 4 to 12 inch(100 to 300 mm)top of deflector to ceiling distance. 4. Approved by the Loss Prevention Certification Board(LPCB Ref.No.007a/04)at a 4 to 6 inch(100 to 150 mm)top of deflector to ceiling distance.The LPC does not rate the thermal sensitivity of horizontal sidewall sprinklers. 5. Listed by Underwriters Laboratories,Inc.as Quick Response Sprinklers for use in Light and Ordinary Hazard Occupancies. 6. Listed by Underwriters Laboratories for use in Canada(C-UL)as Quick Response Sprinklers for use in Light and Ordinary Hazard Occupancies. 7. Approved by Factory Mutual Research Corporation(FM)as Quick Response Sprinklers for use in Light Hazard Occupancies. 8. Approved by the Loss Prevention Certification Board(LPCB Ref.No.094a/06&007a/04)as Quick Response Sprinklers. 9. Approved by the City of New York under MEA 354-01-E. 10. Approved by the Loss Prevention Certification Board(LPCB Ref.No.094a/06)at a 4 to 6 inch(100 to 150 mm)top of deflector to ceiling distance.The LPC does not rate the thermal sensitivity of horizontal sidewall sprinklers. 11. Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C-UL Listed,the sprinklers are UL and C-UL Listed as Corrosion Resis- tant Sprinklers.Where Lead Coated Sprinklers are noted to be FM Approved,the sprinklers are FM Approved as Corrosion Resistant Sprinklers. Installed with Style 10(1/2"NPT)3/4"Total Adjustment Recessed Escutcheon. "Installed with Style 20(1/2"NPT)1/2"Total Adjustment Recessed Escutcheon. —Frame and deflector only. TABLE A LABORATORY LISTINGS AND APPROVALS TFP176 Page 6 of 6 SPRINKLER FINISH K TYPE NATURAL BRASS CHROME PLATED POLYESTER LEAD COATED HORIZONTAL SIDEWALL 250 PSI(17,2 BAR) (TY3331) or 175PSI(12,1 BAR) 5.6 RECESSED HORIZ. 1/2 SIDEWALL(TY3331) (SEE NOTE 1) NPT VERTICAL SIDEWALL 175 PSI(12,1 BAR) (TY3431) NOTES: 1. The maximum working pressure of 250 psi(17,2 bar)only applies to the Listing by Underwriters Laboratories,Inc.(UL);the Listing by Underwriters Laboratories,Inc.for use in Canada(C-UL);and,the Approval by the City of New York. TABLE B MAXIMUM WORKING PRESSURE P/N57 - XXX - X - XXX I I SIN SPRINKLER TEMPERATURE FINISH RATINGS 378 HORIZONTAL SIDEWALL TY3331 1 NATURAL BRASS 135 135°F(57°C) F___ 155 155°F(68°C) 375 VERTICAL SIDEWALL TY3431 3 PURE WHITE(RAL9010)' POLYESTER 4 SIGNAL WHITE(RAL9003) 175 175°F(79°C) POLYESTER 5 JET BLACK(RAL9005)" 200 200°F(93°C) POLYESTER 7 LEAD COATED 286 286°F(141°C) 9 CHROME PLATED 'Eastern Hemisphere sales only. "Available in 155°F(68°C)or 200°F (93°C)temperature rating only. TABLE C PART NUMBER SELECTION SERIES TY-FRB HORIZONTAL AND VERTICAL SIDEWALL SPRINKLERS Ordering Sprinkler Assemblies with NPT Recessed Escutcheon Thread Connections: Specify:Style(10 or 20)Recessed Es- Procedure Specify: Series TY-FRB(specify SIN), cutcheon with (specify*) finish, P/N (specify K-factor), (specify) Horizontal (specify*). Contactour local distributor for avail- Sidewall or Vertical Sidewall Sprinkler, Y *Refer to Technical Data Sheet TFP770 • ability. When placing an order, indi- Standard Response, Standard Cov- cate the full product name and Part erage, (specify) temperature rating, Sprinkler Wrench - Number(P/N). (specify) finish or coating, P/N (spec- Specify: W-Type 6 Sprinkler Wrench, ify from Table C) P/N 56-000-6-387 . Specify: W-Type 7 Sprinkler Wrench, P/N 56-850-4-001 GLOBAL HEADQUARTERS 11400 Pennbrook Parkway,Lansdale,PA 19446 I Telephone+1-215-362-0700 Copyright®2013 Tyco Fire Products,LP. All rights reserved. two TEFLON is trademark of The DuPont Corporation. Fire Protection Products FireLock® Buterfly Valve ✓CtauiiC Style 705 with Weatherproof Actuator 10.81 Material Specifications: Mt. _ i Body: Ductile iron conforming to ASTM A-536, grade 4 65-45-12 End Face, 2 —6"/50— 150 mm: Ductile iron conforming to ASTM A-536,grade 65-45-12 Seal Retainer, 8— 127200—300 mm: Ductile iron conforming to ASTM A-536, grade 65-45-12 Approvals/Listings: Coating: Black alkyd enamel coos FM Vds) IIJDCO Disc: Ductile iron conforming to ASTM A-536, grade #G410001 104j/04 65-45-12, with electroless nickel coating conforming to See VictaulicPuhlicatlon 10.01 for more details. ASTM B-733 Seat: Product Description: ❑ Grade "E" EPDM The Series 705 Butterfly Valve features a weatherproof actuator housing Approved for indoor or outdoor use, a Stems: 416 stainless steel conforming to ASTM A-582 ductile iron body and disc with EPDM seats. Designed for fire protection services only.Victaulic FireLock Stem Seal Cartridge: C36000 brass Series 705 Butterfly Valve is cULus Listed, LPCB Listed, • FM and VdS Approved for 300 psi/2068 kPa service. Bearings: Stainless Steel with TFE lining Contact Victaulic for details of agency approvals. Stem Seals: EPDM Stem Retaining Ring: Carbon steel Actuator: ❑ 2—8'/50—200mm: Brass or bronze traveling nut on a steel lead screw, in a ductile iron housing ❑ 10— 12'/250—300mm: Steel worm and cast iron quadrant gear, in a cast iron housing • Job/Owner Engineer System No. Spec Section Location Paragraph Contractor Approved Submitted By Date Date victaulic.com I Butterfly Valve I Series 705 I Publication 10.81 10.81 5662 Rev F Updated 11/2014 0 2014 Victaulic Company.All rights reserved. 1 iCtaUIicr • victaulic.com I Butterfly Valve I Series 705 I Publication 10.81 Approvals and Listings: Approval/Listing Service Pressures Series 705 Butterfly Valve Size cULus FM Vds LPCB 2"/50 mm up to 300psi/2068kPa n/a up to 300psi/2068kPa up to 300psi/2068kPa 2'h"165 mm up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 76.1 mm up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 3"/80 mm up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 4"/100 mm up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 5"/125 mm up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 139.7 mm up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 6'/150 mm up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 165.1 mm up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 8"/200 mm up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa up to 300psi/2068kPa 10"/250 mm up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa 12"/300 mm up to 300psi/2068kPa up to 300psi/2068kPa n/a up to 300psi/2068kPa • 10.81 5662 Rev F Updated 11/2014 ©2014 Victaulic Company.All rights reserved. victaulic.com 2 ictaluliC' victaulic.com I Butterfly Valve I Series 705 I Publication 10.81 Dimensions: .lKi 1 ra-0 - =fi10 i r i 0 �, • ,,I4_!. B r __. F4 ,- -»I G E-•, A -D NOTE:OPTIONAL 1715MM TAP AVAILABLE. CONTACT VICTAULIC FOR DETAILS. Actual Dimensions Nominal Outside E to E Size Diameter A B C D E F G DIA H J inches inches inches inches inches inches inches inches inches inches inches mm mm mm mm mm mm mm mm mm mm mm 2 2.375 4.25 2.28 6.41 _ _ 4.00 4.22 4.50 2.12 60.3 60.3 108.0 57.9 162.8 101.6 107.2 114.3 53.8 2' 2.875 3.77 2.28 7.54 _ _ 4.00 4.22 4.50 1.77 73 73.0 95.8 57.9 191.5 101.6 107.2 114.3 45.0 76.1 mm 3.000 3.77 2.28 7.54 _ - 4.00 4.22 4.50 1.77 76.1 95.8 57.9 191.5 101.6 107.2 114.3 45.0 3 3.500 3.77 2.53 7.79 _ _ 4.50 4.22 4.50 1.77 88.9 88.9 95.8 64.3 197.9 114.3 107.2 114.3 45.0 108mm 4.250 4.63 2.88 8.81 - - 5.50 4.22 4.50 2.20 108.0 117.6 73.2 223.8 139.7 107.2 114.3 55.9 4 4.500 4.63 2.88 8.81 _ _ 5.50 4.22 4.50 2.20 114.3 114.3 117.6 73.2 223.8 139.7 107.2 1143 55.9 133 mm 5.250 5.88 3.35 10.88 - - 6.56 6.19 6.30 2.58 133.0 149.4 85.1 276.4 166.6 157.2 160.0 65.5 5.500 5.88 3.35 10.88 _ _ 6.56 6.19 6.30 2.58 139.7 mm 139.7 149.4 85.1 276.4 166.6 157.2 160.0 65.6 5 5.563 5.88 3.35 10.88 _ _ 6.56 6.19 6.30 2.58 141.3 141.3 149.4 85.1 276.4 166.6 157.2 160.0 65.5 159mm 6.250 5.88 3.84 11.38 - 0.41 7.52 6.19 6.30 2.58 159.0 149.4 97.5 289.1 10.4 191.0 157.2 160.0 65.5 165.1 mm 6.500 5.88 3.84 11.38 - 0.41 7.52 6.19 6.30 2.58 165.1 149.4 97.5 289.1 10.4 191.0 157.2 160.0 65.5 6 6.625 5.88 3.84 11.38 _ 0.41 7.52 6.19 6.30 1.90 1683 168.3 149.4 97.5 289.1 10.4 191.0 157.2 160.0 48.3 8 8.625 5.33 5.07 13.53 0.80 1.47 10.00 6.19 8.10 2.33 219.1 219.1 135.4 128.8 343.6 20.3 37.3 254.0 157.2 205.7 59.2 10 10.750 6.40 6.37 15.64 1.41 1.81 12.25 8.10 9.00 _ 273 273.0 162.6 161.8 397.3 35.8 46.0 311.2 205.7 228.6 12 12.750 6.50 7.36 16.64 2.30 2.80 14.25 8.10 9.00 - 323.9 323.9 165.1 186.9 422.7 58.4 71.1 362.0 205.7 228.6 10.81 5662 Rev F Updated 11/2014 0 2014 Victaulic Company.AD rights reserved. victaulic.com 3 iataulic victaulic.com I Butterfly Valve I Series 705 I Publication 10.81 Performance: The chart expresses the frictional resistance of Victaulic Series 705 Butterfly Valve in equivalent feet/ meters of straight pipe. Nominal Outside Equivalent Size Diameter mm mm Feet/m inches inches of pipe 2 2.375 6 50 60.3 1.8 21/2 2.875 6 65 73.0 1.8 76.1 mm 3.000 6 76.1 1.8 3 3.500 7 80 88.9 2.1 4 4.500 8 100 114.3 2.4 108 mm 108 mm 2.4 5 5.563 12 125 141.3 3.7 133 mm 133 mm 12 3.7 139.7 mm 5.500 12 139.7 3.7 6 6.625 14 150 168.3 4.2 159 mm 159 mm 14 4.3 165.1 mm 6.500 14 165.1 4.2 8 8.625 16 200 219.1 4.9 10 10.750 18 250 273.0 5.5 12 12.750 19 300 323.9 5.8 10.81 5662 Rev F Updated 11/2014 ©2014 Victaulic Company.All rights reserved. victaulic.com 4 ictaulic victaulic.com I Butterfly Valve I Series 705 I Publication 10.81 Performance: C„values for flow of water at+60°F/+16°C through a fully open valve are shown in the table below. For additional details, contact Victaulic. Formulas for C,values Formulas for K„values AP=Qz/C z Where: AP=Qz/K z Where: Flow Coefficient C Flow Factor K Q=CvxVAP Q=KvxVAP Q(Flow) GPM Q(Flow) mVhr AP(Pressure Drop) psi AP(Pressure) bar Valve Size Full Open Valve Size Full Open Actual Actual Nominal Outside Nominal Outside Size Diameter Flow Coefficient Size Diameter Flow Coefficient inches inches C, inches inches K,, mm mm mm mm 2 2.375 2 2.375 50 60.3 170 50 60.3 147 2 Y7 2.875 2'h 2.875 260 225 65 73.0 65 73.0 376.1 mm 000 260 7676.1 .1 mm 763.0� 225 3 3.500 3 3.500 80 88.9 440 80 88.9 380 4 4.500 4 4.500 100 114.3 820 100 114.3 710 108mm 108mm 820 108mm 108mm 710 5 5.563 5 5.563 125 141.3 1200 125 141.3 1040 133 mm 133 mm 1200 133 mm 133 mm 1040 139.7 mm 5.5003 1200 139.7 .7mm 139 1040 6 6.625 6 6.625 150 168.3 1800 150 168.3 1560 159 mm 159 mm 1800 159 mm 159 mm 1560 165.1 mm 6.50065 1800 165.1 .1 mm 6.565.100 65 1560 18 8.625 8 8.625 200 219.1 3400 200 219.1 2940 10 10.750 10 10.750 250 273.0 5800 250 273.0 5020 12 12.750 12 12.750 9000 7790 300 323.9 300 323.9 • 10.81 5662 Rev F Updated 11/2014 ®2014 Victaulic Company.All rights reserved. victaulic.com 5 ctaulic' victaulic.com I Butterfly Valve I Series 705 I Publication 10.81 Switch and Wiring: LIIDI,' JUNCTION CONDUI 4.40/ 1. The supervisory switch contains two single pole, > �;;� ���;;_� double throw, pre wired switches. —_'�, 1,.(,-C' OONNi1TORT �1, 2. Switches are rated: /16 10 amps @ 125 or 250 VAC/60 Hz 0.50 amps CP 125 VDC E'ER[ALARM. "D:NJ-0�.'�N�4:ti5TOT 0.25 amps© 250 VDC CSNPRo SUPERVISORYPANORNGTiND(A 09 CIUIT CIRCUIT 3. Switches supervise the valve in the "OPEN" position. SW-C- CONTACT 9AA�ND _, t� °A AT DO AND MI 5. One switch has two#18 insulated wires per terminal, °SA"T„S�DC. which permit complete supervision of leads(refer ""s°"D a ii to diagrams and notes below). The second switch °°" ' w,'A��so,;Rc has one#18 insulated wire per terminal. This double SwitchT Z'eods per terminalSwit<h 2:1 lead per terminal circuit provides flexibility to operate two electrical devices at separate locations, such as an indicating light and an audible alarm, in the area that the valve NOTE: The above diagram shows a connection between is installed. the common terminal (yellow–S1 and yellow-with- orange stripe–S2) and the normally closed terminal 6. A#14 insulated ground lead (green) is provided. (blue–S1 and blue-with-orange stripe–S2). In this Switch #1 =S1 example, the indicator light and alarm will stay on until the valve is fully open. When the valve is fully open, the For connection to the supervisory circuit of a UL indicator light and alarm will go out. Cap off any unused Listed alarm control panel wires (e.g. brown with orange stripe). Switch #2 =S2 Only S1 (two leads per terminal) may be connected to - Auxiliary switch that may be connected to auxiliary the fire alarm control panel. devices, per the authority having jurisdiction The connection of the alarm switch wiring shall be in accordance with NFPA 72 and the auxiliary switch per Normally Closed: (2) Blue NFPA 70(NEC). Sl Common: (2) Yellow Normally Closed: Blue with Orange Stripe S2 Normally Open: Brown with Orange Stripe Common: Yellow with Orange Stripe Installation Note Reference should always be made to the 1100 V0lau c 1.0 c Insta:ation Hancbook for This product shall be manufactured by Victaulic or to Victaulic specifications.All products the product you are installing.Handbooks are included with each shipment of Victaulic to be installed in accordance with current Victaulic installation/assembly instructions. products for complete installation and assembly data,and are available in PDF format Victaulic reserves the right to change product specifications,designs and standard on our website at www.victaulic.com. equipment without notice and without incurring obligations. Warranty Trademarks Refer to the Warranty section of the current Price List or contact Victaulic for details. Victaulic®is a registered trademark of Victaulic Company. 10.81 5662 Rev F Updated 11/2014 ©2014 Victaulic Company.All rights reserved. victaulic.com 6 ictaulic* FireLock® Fittings 4tauiicr 10.03 - Material Specifications: ., Fitting: Ductile iron conforming to ASTM A-536, grade 65-45-12. 0 11 Fitting Coating: ❑ Orange enamel ❑ Red enamel in Europe, Middle East, Africa, and India ❑ Optional: Hot dipped galvanized Approvals/Listings: C®us Q ILPCBI VdS uslw Product Description: FireLock® products comprise a unique system specifically designed for fire protection services. FireLock full-flow elbows and tees feature CAD- developed, hydrodynamic design, affording a shorter center-to-end dimension than standard fittings. A noticeable bulge allows the water to make a smoother turn to maintain similar flow characteristics as standard full flow fittings. FireLock fittings are designed for use exclusively with Victaulic couplings that have been Listed or Approved for Fire Protection Services. Use of other couplings or flange adapters may result in bolt pad interference. Refer to the appropriate listing agency or approval body for pressure ratings. Pressure ratings vary by agency. Job/Owner Engineer System No. Spec Section Location Paragraph - Contractor Approved Submitted By Date Date victaulic.com I FireLock® Fittings I Publication 10.03 10.03 1539 Rev M Updated 12/2014 ®2014 Victaulic Company.All rights reserved. 1ictauIic1 victaulic.com I FireLock® Fittings I Publication 10.03 Dimensions: hCtoE+I C I I ^a i t 0 CME p 0 T to E .1� •-to I_ i Mr), to t� NO.001 NO.003 NO.002 No.006 No.001 No.003 No.002 No.006 90°Elbow 45°Elbow Straight Tee Cap _ Actual Approx. Approx. Approx. Approx. Nominal Outside Weight Weight Weight Weight Size Diameter C to E Each C to E Each C to E Each C to E Each inches inches inches Lbs. inches Lbs. inches Lbs. inches Lbs. mm mm mm kg mm kg mm kg mm kg 11/4 1.660 0.82 0.3 32 42.4 - - - - - - 21 0.1 11/2 1.900 - - - - - - 0.82 0.4 40 48.3 - - - - - - 21 0.2 _ 2 2.375 2.75 1.7 2.00 1.8 2.75 2.4 0.88 0.6 50 60.3 70 0.8 51 0.8 70 1.1 22 0.3 21/2 2.875 3.00 3.1 2.25 2.2 3.00 3.6 0.88 1.0 65 73.0 76 1.4 57 1.0 76 1.6 22 0.5 3.000 3.00 3.30 2.25 2.4 3.00 3.8 76.1 mm - - 76.1 76 1.5 57 1.1 76.2 1.7 3 3.500 3.38 4.0 2.50 3.1 3.38 5.3 0.88 1.2 80 88.9 86 1.8 _ 64 1.4 86 2.4 22 0.5 108mm 4.250 4.00 5.7 3.00 5.1 4.00 7.5 - 108.0 102 2.6 76 2.3 102 3.4 4 4.500 4.00 6.7 3.00 5.6 4.00 8.7 1.00 2.4 . 100 114.3 _ 102 3.0 76 2.5 102 3.9 25 1.1 . 5 5.563 4.88 12.6 3.25 8.3 4.88 15.7 1.00 4.1 125 141.3 124 5.7 83 3.8 124 7.1 25 1.9 5.500 4.88 12.4 3.25 8.2 4.88 15.4 • 139.7 mm _ - 139.7 124.0 5.6 82.6 3.7 124.0 6.9 6.250 5.50 12.6 3.50 9.2 5.50 17.9 159mm _ - 158.8 140 5.7 89 4.2 140 8.0 6 6.625 5.50 18.3 3.50 11.7 5.50 22.7 1.00 5.9 150 168.3 140 8.3 89 5.3 140 10.3 25 2.7 165.1 mm 6.500 5.43 17.6 3.50 11.4 5.50 22.0 - 165.1 139.7 7.9 88.9 5.2 139.7 9.9 8 8.625 6.81 25.5 4.25 20.4 6.94 38.7 1.13 12.7 200 219.1 173 11.6 108 9.3 176 17.6 29 5.8 10.03 1539 Rev M Updated 12/2014 ©2014 Victaulic Company.All rights reserved. victaulic.com 2 ictauli victaulic.com I FireLock® Fittings I Publication 10.03 Flow Data: .s Frictional Resistance Actual Equivalent Feet/meters of Straight Pipe' Nominal Outside No.002 Size Diameter Elbows Straight Tee inches inches No.001 No.003 mm mm 90°Elbow 45°Elbow Branch Run 11/4 1.660 - - - - 32 42.4 - - - - 1' 1.900 - - 40 48.3 - - - - 2 2.375 3.5 1.8 8.5 3.5 50 60.3 1.1 _ 0.5 2.6 1.1 2' 2.875 4.3 2.2 10.8 4.3 65 73.0 1.3 0.7 3.3 _ 1.3 76.1 mm 3.000 4.5 2.3 11.0 4.5 76.1 1.4 0.7 3.4 1.4 3 3.500 5.0 2.6 13.0 5.0 80 88.9 1.5 0.8 4.0 1.5 108mm 4.250 6.4 3.2 15.3 6.4 108.0 2.0 0.9 4.7 2.0 4 4.500 6.8 3.4 16.0 6.8 100 114.3 2.1 1.0 4.9 2.1 5 5.563 8.5 4.2 21.0 8.5 125 141.3 2.6 1.3 6.4 2.6 139.7 mm 5.500 8.3 4.1 20.6 8.3 139.7 2.5 1.3 6.3 2.5 159 mm 6.250 9.4 4.9 25.0 9.6 158.8 2.9 1.5 7.6 2.9 • 6 6.625 10.0 5.0 25.0 10.0 150 168.3 3.0 1.5 7.6 3.0 165.1 mm 6.500 9.8 4.9 24.5 9.8 165.1 3.0 1.5 7.5 3.0 8 8.625 13.0 5.0 33.0 13.0 200 219.1 4.0 1.5 10.1 4.0 ' The flow data listed is based upon the pressure drop of Schedule 40 pipe. General Notes: NOTE: When assembling FireLock EZ couplings onto end caps, take additional care to make certain the end cap is fully seated against the gasket end stop. For FireLock EZ Style 009N/009H couplings, use FireLock No. 006 end caps containing the "EZ" marking on the inside face or No. 60 end caps containing the "QV EZ" marking on the inside face. Non-Victaulic end cap products shall not be used with Style 009/009V/009H couplings. s Installation Note Reference should always be made to the I-100 V claw-c F ielc Insla:at an I lanebook for This product shall be manufactured by Victaulic or to Victaulic specifications.All products the product you are installing.Handbooks are included with each shipment of Victaulic to be installed in accordance with current Victaulic installation/assembly instructions. products for complete installation and assembly data,and are available in PDF format Victaulic reserves the right to change product specifications,designs and standard on our website at www.victaulic.com. equipment without notice and without incurring obligations. Warranty Trademarks Refer to the Warranty section of the current Price List or contact Victaulic for details. Victaulic•is a registered trademark of Victaulic Company. 10.03 1539 Rev M Updated 12/2014 ®2014 Victaulic Company.All rights reserved. victaulic.com 3 ictaulic'