Report RECEIVED
APR 04 2016
CITY OF 1•
sf_, �.. _t
vvyAT
TBUILDING
VA.4 !(-14114
r ,r FIRE PROTECTION, INC.
9095 S.W. Burnham
Tigard, OR 97223
GODIVA WASH SQ
9585 SW WASHINGTON SQ RD #B04
PORTLAND, OR 97223
CITY OF TIGARD
REVIEWED FOR CODE COMPLIANCE
Approved: [ `7
OTC: [ ]
Permit#: - &.O„
Address
Suitt I,� i�
Big 41.4.13
.Adeji' Date:
OFFICE COPY
FIRE PROTECTION
EQUIPMENT SUBMITTAL
ticti Worldwide
Contacts www.tyco-fire.com
Series RFII — 5.6 K-factor
"Royal Flush II" Concealed Pendent Sprinklers
Quick & Standard Response, Standard Coverage
General stallation or finish. The tip of the Pro-
tective Cap can be used to mark the
Description center of the ceiling hole into plaster
p board or ceiling tiles by gently push- °`
ingthe ceilingproduct against the Pro- «y
The TYCO Series RFII 5.6 K-factor, g
"Royal Flush II" Concealed Pendent tective Cap. When ceiling installation
Sprinklers Quick Response (3-mm is complete, the Protective Cap is re-
moved and the Cover Plate/Retainer ---
bulb) and Standard Response (5-mm Assemblyis installed.
bulb), are decorative sprinklers featur-
ing a flat cover plate designed to con- As an option,the Series RFII Standard "'
ceal the sprinkler.These sprinklers are Response(5-mm bulb)"Royal Flush II"
optimal for architecturally sensitive ar- Concealed Pendent Sprinklers can be
eas such as hotel lobbies,office build- fitted with a silicone Air and Dust Seal.
ings,churches,and restaurants. (Refer to Figure 5.) The Air and Dust •
TY3531 (3 mm Bulb) is UL Listed,
Seal is intended for sensitive areas C-UL Listed, VdS Approved (Certif-
Each sprinkler includes a Cover Plate/ icate No. G4090007), and NYC Ap-
Retainer Assembly and a Sprinkler/ where it is desirable to prevent air and proved (MEA 353-01-E) as Quick
Support Cup Assembly. The separa- dust from the area above the ceiling to Response.
ble, two-piece assembly design pro-
pass through the cover plate.
vides the following benefits: • TY3531 (3 mm Bulb) is FM and
NOTICE LPCB Approved (Ref. No. 094a/10)
• Allows installation of the sprinklers The Series RFII Concealed Pendent Approved as Standard Response.
and pressure testing of the fire pro- FactoryMutual and LPCB do not
tection system prior to installation Sprinklers described herein must be
of a suspended ceilingor lica installed and maintained in compli- approve any concealed sprinklers
p pp ance with this document and with the for quick response.
tion of the finish coating to a fixed
applicable standards of the National
ceiling. pP TY3551 (5-mm Bulb) is UL Listed,
Fire Protection Association, in addi- C-UL Listed, FM Approved, LPCB
• Permits the removal of suspended tion to the standards of any authori- Approved (Ref. No. 094a/9), and
ceiling panels for access to building ties having jurisdiction.Failure to do so NYC Approved (MEA 353-01-E) as
service equipment without having may impair the performance of these Standard Response.
to first shut down the fire protection devices.
system and remove sprinklers. Approvals for Air and Dust Seal
The owner is responsible for maintain-
• Provides for 1/2 inch (12,7 mm) of ing their fire protection system and de- UL and C-UL Listed for use with the
vertical adjustment to allow a mea- vices in proper operating condition. RFII Standard Response Concealed
sure of flexibility in determining the The installing contractor or sprinkler Sprinkler(TY3551).
length of fixed piping to cut for the manufacturer should be contacted Maximum Working Pressure
sprinkler drops. with any questions.
Maximum 250 psi (17,3 bar) by UL,
The Series RFII Sprinklers are shipped C-UL,and NYC
with a Disposable Protective Cap.The Sprinkler
Protective Cap is temporarily removed p Maximum 175 psi (12,1 bar) by FM,
•
during installation and replaced to help Identification VdS,and LPCB
protect the sprinkler during ceiling in- Temperature Rating
Number (SIN) 155°F(68°C)Sprinkler with
IMPORTANT TY3531 — 3 mm bulb 139°F(59°C)Plate
Always refer to Technical Data
Sheet TFP700 for the "INSTALLER TY3551 — 5 mm bulb 200°F(93°C)Sprinkler with
WARNING" that provides cautions 165°F(74°C)Plate
with respect to handling and instal- Technical Discharge Coefficient
lation of sprinkler systems and corn-
K=5.6 GPM/psi""2(80,6 LPM/bar1i2)
ponents. Improper handling and in- Data
stallation can permanently damage Adjustment
a sprinkler system or its components Sprinkler Approvals 1/2 inch(12,7 mm)
and cause the sprinkler to fail to Approvals apply only to the service
operate in a fire situation or cause it conditions indicated in the Design Cri- Finishes
, to operate prematurely. teria section. See the Ordering Procedure section.
Page 1 of 4 MARCH 2013 TFP181
TFP181
Page 2 of 4
Physical Characteristics 1/2" NPT SEALING
Frame Bronze , ASSEMBLY
. Support Cup Chrome ,
Plated Steel
Guide Pins Stainless Steel FRAME ,), t
Deflector Bronze J/
Compression Screw Brass 'L CAP
Bulb Glass ;��
Cap Bronze or Copper SUPPORT
Sealing Assembly Beryllium CUP WITH I BULB
Nickel w/TEFLON ROLL FORMED
. Cover Plate Brass THREADS
Retainer Brass
Ejection Spring Stainless Steel COMPRESSION
Design _ SCREW
Criteria PINS(2) 4' % %' �
� / 40
The TYCO Series RFII 5.6 K-factor, DEFLECTOR
"Royal Flush II" Concealed Pendent - (DROPPED
Sprinklers are intended for fire protec- DEFLECTOR i �__; r -`__3i POSITION)
tion systems designed in accordance -_, r-
with the standard installation rules rec-
ognized by the applicable Listing or I SPRINKLER/SUPPORT CUP
Approval agency;for example,UL List- ASSEMBLY
ing is based on NFPA 13 and VdS Ap-
proval is based on the CEA 4001. THREAD INTO P I RETAINER
For more information on LPCB and SUPPORT I 0 I WITH THREAD
CUP UNTIL + O DIMPLES
VdS Approvals, contact Tyco Fire Pro- MOUNTING
tection Products at the following office: SURFACE IS EJECTION
Enschede,Netherlands FLUSH WITH SPRING
Telephone:31-53-428-4444 CEILING
Fax:31-53-428-3377
The Series RFII Concealed Pendent ` --
_ Sprinklers are only listed and approved �r
with the Series RFII Concealed Cover
Plates having a factory applied finish. SOLDER J/ COVER
TABS(3) COVER PLATE/RETAINER PLATE
NOTICE ASSEMBLY
Do not use the Series RFII in applica- FIGURE 1
tions where the air pressure above MODEL RFII CONCEALED SPRINKLER
the ceiling is greater than that be- ASSEMBLY
low. Down drafts through the Sprin-
kler/Support Cup Assembly can delay Installation Do not attempt to compensate for in-
sprinkler operation in a fire situation. sufficient adjustment in the Sprinkler
The TYCO Series RFII 5.6 K-factor, by under-or over-tightening the Sprin-
Operation "Royal Flush II" Concealed Pendent kler/Support Cup Assembly. Re-adjust
p Sprinklers must be installed in accor- the position of the sprinkler fitting to
When exposed to heat from a fire,the dance with this section. suit.
Cover Plate, normally soldered to the General Instructions Step 1. Install the sprinkler only in the
exposeRetalr at thehree Sprinkler/Support oints, falls aCup line
Do not install any bulb-type sprinkler if of the nstpr nklernper�pend perpth the endicular
the
Assembly. the bulb is cracked or there is a loss mounting surface.
of liquid from the bulb. With the sprin- Step 2. Remove the Protective Cap.
The Deflector - supported by the kler held horizontally, a small air bub-
Guide Pins - then drops down to its ble should be present. The diameter Step 3. With pipe thread sealant ap-
operational position. of the air bubble is approximately 1/16 plied to the pipe threads, hand-tighten
inch (1,6 mm)for the 155°F (68°C)and the sprinkler into the sprinkler fitting.
The glass bulb exposedconsa fluid that ex-
pands
When 3/32 inch(2,4 mm)for the 200°F(93°C) Step 4. Wrench-tighten the sprinkler
the when to heat. temperature ratings. using only the RFII Sprinkler Wrench.
the rated temperature is reached, the (Refer to Figure 3.) Apply the RFII
fluid expands sufficiently to shatter the A leak-tight 1/2 inch NPT sprinkler joint Sprinkler Wrench to the Sprinkler as
glass bulb, activating the sprinkler and should be obtained by applying a min- shown in Figure 3.
. allowing water to flow. imum to maximum torque of 7 to 14 Step 5. Replace the Protective Cap
ft.-lbs. (9,5 to 19,0 Nm). Higher levels by pushing it upwards until it bottoms
of torque can distort the sprinkler In- out against the Support Cup. (Refer
let with consequent leakage or impair- to Figure 4.)The Protective Cap helps
ment of the sprinkler. prevent damage to the Deflector and
TFP181
Page 3 of 4
FACE OF CLEARANCE HOLE CLEARANCE
SPRINKLER - DIAMETER HOLE
- FITTING ` DIMENSION C f
SPRINKLER J :�
SUPPORT CUP J e
ASSEMBLY I 1/2"(12,7 mm) 'iTHREADED- D ADJUSTMENT ��� „ilkilliti
FACE
. OF CEILING, y o
4
RETAINING RING '•''
MOUNTING j ;I
SURFACE / ,4
\ I I FIGURE 4
` DISPOSABLE PROTECTIVE CAP
‘•\ ,d 'NM,
i Arms during ceiling installation and/or
E.-- -.-.0
�___ _ I �r=� finish. You can also use the Protective
T -'- Cap to locate the center of the clear-
3/16”to 11/16" MANUFACTURER DEFLECTOR COVER PLATE ance hole by gently pushing the ceiling
(4,8 to 17,5 mm) PRESET GAP IN DROPPED RETAINER material up against the center point of
REFERENCE 3/32"(2,4 mm) POSITION ASSEMBLY the Protective Cap.
COVER PLATE COVER PLATE NOTICE
-PROFILE DEPTH DIAMETER
As long as the Protective Cap remains
DIMENSION B DIMENSION A in place, the system is considered
A:3-1/4 inches(82,6 mm) C:2-3/8 to 2-5/8 inches(60,3 to 66,7 mm) "Out of Service"
Step 6.After the ceiling has been com-
B:3/16 inches(4,8 mm) D:1-3/4 to 2-1/4 inches(44,5 to 57,2 mm) pleted with the 2-1/2 inch(63,5 mm)di-
ameter clearance hole and in prepa-
FIGURE 2 ration for installing the Cover Plate/
SERIES CONCEALED SPRINKLER INSTALLATION DIMENSIONS Retainer Assembly, remove and dis-
card the Protective Cap.Verify that the
Deflector moves up and down freely.
If the Sprinkler is damaged and the
Deflector does not move up and down
j—1 FRAME % 1=i, freely, replace the entire Sprinkler.
/— --- �1'' Do not attempt to modify or repair a
i i
�I damaged sprinkler.
111
RT — ' _ �, Step 7. When installing an Air and
CUP I - I i , Dust Seal, refer to Figure 5; otherwise,
i proceed to Step 8. To attach the Air
Idol ,�.', i and Dust Seal, verify the angle of the
I � � outside edge of the seal is oriented ac-
cording to Figure 5. Start the edge of
— — — -- the Retainer in the grooved slot of the
0
.limmil7/8"(23 mm) Air and Dust Seal and continue around
SQUARE the retainer until the entire Air and Dust
- Seal is engaged.
/ — Step 8. Screw on the Cover Plate/
ALIGN �� �� Retainer Assembly until the Retainer
ARROWS WITH i i i (shown in Figure 2)or the Air and Dust
FRAME ARMS J \_ Seal (shown in Figure 5) contacts the
�1 al ceiling. Do not continue to screw on
i—i� the Cover Plate/Retainer Assembly
ACCEPTS \ `\, r�� so that it lifts a ceiling panel out of its
0 1/2"SOCKET \ normal position. If you cannot engage
DRIVE the Cover Plate/Retainer Assembly
• FIGURE 3 with the Support Cup or you cannot
SPRINKLER WRENCH engage the Cover Plate/Retainer As-
RFIIsembly sufficiently to contact the ceil-
ing, you must reposition the Sprinkler
Fitting.
TFP181
Page 4 of 4
Care and SUPPORT -- SPRINKLER FACE OF ORIENT
• Maintenance
CUP CEILING , \ SHOWN
B SVEEAL
LAS=L
The TYCO Series RFII 5.6 K-fac 1COVER
tor, "Royal Flush II" Concealed Pen PLATE
lir
dent Sprinklers must be maintained i ; RETAINER MM.
and serviced in accordance with thisASSEMBLY
section. W.
Before closing a fire protection system +I.
-_ . AIRmain control valve for maintenance 'work on the fire protection system that /, 1- !.��/ / AND DUST
it controls, obtain permission to shutes— --• �� LIP OF COVER SEAL
down the affected fire protection sys- RETAINER PLATE
tern from the proper authorities and FIGURE 5
notify all personnel who may be affect- OPTIONAL AIR AND DUST SEAL FOR SERIES RFII(TY3551)
ed by this action.
Absence of the Cover Plate/Retainer If you must remove a sprinkler, do not Ordering
Assembly can delay sprinkler opera- reinstall it or a replacement without re-
tion in a fire situation. installing the Cover Plate/Retainer As- Procedure
When properly installed, there is a sembly. If a Cover Plate/Retainer As Y
nominal 3/32 inch(2,4 mm) air gap be- sembly becomes dislodged during Contact your local distributor for
tween the lip of the Cover Plate and the service,replace it immediately. availability. When placing an order,
ceiling,as shown in Figure 2. The owner is responsible for the in- indicate the full product name.
specThis air gap is necessary for proper their ire testing, and maintenance of Sprinkler/Support Cup Assembly
operation the sprinkler. the cell their fire protection system and devic-
op requires of repaintinghespafter. If sprinkler es in compliance with this document, Specify: Series RFII (specify SIN),
ingeensure that the new paint as well as with the applicable stan- K=5.6, "Royal Flush II" Pendent Sarin-
installation, dards of the National Fire Protection klers (specify) temperature rating and
does not seal off any of the air gap. Association(e.g.,NFPA 25), in addition (specify)finish, P/N(specify).
Do not pull the Cover Plate relative to to the standards of any other authori-
the Enclosure.Separation may result. ties having jurisdiction.Contact the in- 155°F(68°C) 200°F(93°CI
S rinklers which are found to be leak- stalling contractor or sprinkler manu- TY3531 51-792-1-155 51-792-1-200
pfacturer regarding any questions. TY3551 51-790-1-155 51-790-1-200
ing or exhibiting visible signs of corro-
sion must be replaced. Automatic sprinkler systems should be Separately Ordered Cover Plate/
inspected,tested,and maintained by a Retainer Assembly:
Automatic sprinklers must never be qualified Inspection Service in accor-
painted, plated, coated, or other- dance with local requirements and/or Specify: (temperature rating from be-
wise altered after leaving the factory. national code. low) Series RFII Concealed Cover
' Modified sprinklers must be replaced. Plate with(finish), P/N(specify).
Sprinklers that have been exposed to 139°F(59°C)(a) 165°F(74°C)(b)
corrosive products of combustion, but Grey White
have not operated,should be replaced (RAL9002) 56-792-0-135 56-792-0-165
if they cannot be completely cleaned Brass 56-792-1-135 56-792-1-165
by wiping the sprinkler with a cloth or Pure White(c)
by brushing it with a soft bristle brush. (RAL9010) 56-792-3-135 56-792-3-165
Care must be exercised to avoid dam- Signal white
(RAL9003) 56-792-4-135 56-792-4-165
age to the sprinklers - before, during, Jet Black
and after installation. Sprinklers dam- (RAL9005) 56-792-6-135 59-792-6-165
aged by dropping, striking, wrench Brushed
twist/slippage, or the like, must be re- Chrome 56-792-8-135 56-792-8-165
placed.Also,replace any sprinkler that Chrome 56-792-9-135 56-792-9-1 65
has a cracked bulb or that has lost Custom 56-792-X-135 56-792-X-165
liquid from its bulb. (Ref. Installation (a) For use with 155°F(68°C)sprinklers.
Section.) (b) For use with 200°F(93°C)sprinklers.
Exercise care to avoid damage to (c) Eastern Hemisphere sales only.
sprinklers before, during, and after in- Sprinkler Wrench
stallation.Replace sprinklers damaged Specify: RFII Sprinkler Wrench,
by dropping, striking, wrench twisting, P/N 56-000-1-075.
wrench slipping, or the like. Also, re-
place any sprinkler that has a cracked Air and Dust Seal
bulb or that has lost liquid from its Specify:Air and Dust Seal,
bulb.(Refer to the Installation section.) P/N 56-908-1-001.
GLOBAL HEADQUARTERS 11400 Pennbrook Parkway,Lansdale,PA 19446 I Telephone+1-215-362-0700
Copyright 0 2013 Tyco Fire Products,LP. All rights reserved. Vico
TEFLON is trademark of The DuPont Corporation.
Eddythread 40
A Lightweight Schedule 40 Replacement Pipe
That Has a Corrosion Resistance Ratio of 1.0
Bull Moose Tube Company has been making pipe for a long time and is recognized as a producer of quality pipe
products. Eddythread 40 is designed with the same thoroughness as our other fine pipe products and now our
customers have an option to buy a carefully designed replacement for Schedule 40 that:
• Has a Corrosion Resistance Ratio of 1.0
• Has a Pressure Rating of 300 psi
• Is Lighter Weight Than Schedule 40
• Is Approved by Factory Mutual and Listed by Underwriters Laboratories
• Is Produced in Accordance to ASTM A-135 and A-795
• Can be Used With Standard Schedule 40 Threaded Fittings,
Couplings and Valves
• Is Produced From Steel With Excellent Properties of
Strength and Threadability
• Can be Used in Wet, Dry, Preaction, and Deluge Type Sprinkler Systems*
• Offers Lower Freight Costs
EDDYTHREAD 40 SPECIFICATIONS
NOMINAL PIPE SIZE(in) WEIGHT(lbs/ft) I.D. (in) BUNDLE SIZE
1 1.461 1.083 70
1 1/4 2.070 1.418 51
1 1/2 2.547 1.654 44
2 3.308 2.123 30
CORROSION RESISTANCE RATIOS
NOMINAL PIPE SIZE(in) SCHEDULE 40 EDDYTHREAD 40
1 1.00 1.00
1 1/4 1.00 1.00
1 1/2 1.00 1.00
2 1.00 1.00
*Eddythread 40 can be hot dipped galvanized to meet FM's requirement for dry systems
1819 Clarkson Road For additional information, CL us �
Chesterfield,MO 63017 contact your salesperson today at
■L MOOSE TUBE CO(v ANY (800)325-4467 (800)325-4467 or(636)537-2600 LIPID
FAX:(636)537-2645 in the USA,or from Canada
www.bullmoosetube.com call(800)882-4666 11>
A CAtO company e-mail:sales,cf bullmoosetube.com
APPROVED
All information contained herein is accurate as known at the time of publication. Bull Moose Tube reserves the right to change product specifications without notice and without incurring obligation.
8/08
,' • 1. Ductile Iron Fittings - Class 300 UL/FM
c04) us
APPROVED
• Fig. 35E 3- 90°Elbow LISTED
A Size A Packing Weight
Part Number
` in in Inner Master lb
;---: 1/2 35E 3004 1.13 100 200 0.2
�► 3/4 35E 3006 1.31 - 70 140 0.3
A 1 35E 3010 1.50 40 80 0.5
Ian 1-1/4 35E 3012 1.75 25 50- 0.8
1-1/2 35E 3014 1.94 18 36 1.1
2 35E 3020 225 10 20 1.8
2-1/2 35E 3024 2.70 4 8 3.2
Fig. 35RE3- 90°Reducing Elbow
�� Size Part Number A B Packing Weight
ft ',, 'in" in �" in Inner Master lb
111, 3/4 x 1/2 35RE3006004 1.20 1.22 80 160 0.3
I� 1 x 1/2 35RE3010004 1.26 1.36 70 140 0.4
1 x 3/4 35RE3010006 1.38 1.45 50 100 0.4
�a' A 1-1/4 x 1/4 ...35012004 1.34 . 1.53. • 3,$,5�, 70 0.5
35RE3
012006 1.45 1.63 35 70 0.6
1-1/4 x 1 2 35RE3012010,; _ , ,.1.58... ..a', 1.67..:.,. 30 60 0.7
1-1/2 x 1/2 35RE3014004 1.52 1.75 30 60 0.6
,l-j1,2 x 3/4 x 35RE3Q14006 1.52 � _ 1 75 25:',.:;; 50 0.7
1-1/2 x 1 35RE3014010 1.65 1.80 20 40 0.8
1-1/2 x 1-1/4 35R43014010.r. .11g. ,+" 1.861 'c, 36 1.0
2 x 1/2 35RE3020004 1.60 1.97 18 36 1.0
2.x3/4 " ' 35f'E3020006 . . 1.60 - .1.97 "18 36 1.0
2 x 1 35RE3020010 1.73 2.02 16 32 1.2
2 x 1-114 . 35RE3920012 1.90,,, 2.10 u 12' , 24 1.3
;w El 2 x 1-1/2 35RE3020014 2.02 2.16 10 20 1.5
2-1/2 x 1-1/2 ;:,461.:1 .:602494.
E1x 2.16 ., 2;51 ;, 6 12 2.2
+ 2-1/2 x 2 35RE3024020 2.39 2.60 6 12 2.5
k;I Fig. 35F 3-45°Elbow
Size • A Packing " ., Weight
Part Ilumb`er
1A in In` Inner Master lb
7 1/2 35F 3004 0.88 150 300 0.2
3/4 35F3006 , 0.98 . 80 ;< , .. .160 04tik 1 35F 3010 1.13 40 80 0.5
17114 35E3912 1;.29 ,,.,, ,, 25 50, 0.7
1-1/2 35F 3014 1.44 20 40 1.0
!AIu �
A . 2 35F 3020 1.69 10 20 1.6
2-1/2 35F 3024 1.95 4 8 2.7
Fig. 35T 3- Tee
Size A Packing Weight
Part Number
in • in inner Master lb
IP4IXIA
1/2 35T 3004 1.180 3/4 35T 3006 131 30 60
�_ _I 1 35T 3010 1.50 25 50 0.7
��� - 1-1/4 357 3012 1.75 10 20 1.1
- rr" A lc-)
A 1-1/2 35T 3014 1.94 10 20 1.5
2 35T 3020 2.25 6 12 2.4
•
2-1/2 35T 3024 2.70 4 8 4.3
111 SMITH-COOPER [NTERNATIONAL2' • TOLL FREE 1-800-766-0076 • FAX(323)890-4456 • www.smithcooper.com
Ductile Iron Fittings - Class 300 UL/FM
QttrrY Prays .
c (rj) IIS
APPROVED
. Fig. 35CP3 -Straight Coupling with Ribs
LISTED
A g g P g
Size A Packing Weight
Part Number in Inner Master Ib
Bin
_ 1/2 35CP3004 138 200 400 0.1
3/4 35CP3006 163 100 200 02
fill.
1 35CP3010 1.75 60 120 0.4
1-1/4 - 35CP3012 2.00 ' 35 70 05
1-1/2 35CP3014 2.19 25 50 0.7
2 35CP3020 2.62 15 30 1.2
2-1/2 35CP3024 3.00 9 18 2.2
Fig. 35RC3 -Hex Reducing Coupling111 Part Number
Size A Packing Weight
ik.,,,,IIA
in in Inner Master lb
1 x 1/2 35RC3010004 1.69 80 160 0.3
1 x 3/4 35RC3010006 1.69 60 120 0.4
1-1/4 x 3/4 35RC3012006 2.06 40 80 0.6
2 x 1(not hex) 35RC3020010. 2.81 20 40 1.0
Fig. 35HB3 -Hex Bushing
Size _m A Packing Weight
B in Part Number in - Inner Master lb
1 x 1/2 35HB3010004 1.06 180 360 0.2
i 1 x 3/4 . 35HB3010006„„ 108 ,,. 180 ; 360 0.1
1 , rA 1-1/4 x 1 35HB3012010 1.19 90 180 0.2
� . I 11-1%2 x 1135HB3014010 1.25 75 :' " 150 0.4
1 1/2 x 1-1/4 �35HB3014012 1.25 75150 0.3
m*
�>0 2 x 1 `_ .=351-4B30200 �'
10; 1,38', 40 '° ' 80 0.6
°LJ 2 x 1-1/4 35HB3020012 1 38 40 80 0.6
2 x 1-1/2 ''35H83020014.. 9. .1.38 40 ` 80 0.6
I
Fig. 35SP3 -Square Head Plug
Size , A Packing ,. Weight
in Part Numbr in - Inner Master lb
1/2 35SP3004 0.94 600 1200 0.07
i It' i,I A 3/4 , 4, 35SP0006 '1.12 ‘,,, 350. ?It-, 0.1
is
I. i
1 35SP3010 1.25 200 400 0.1
1-1/4 35SP3012 1.37 100 200 03
1-1/2 35SP3014 1.44 80 160 0.4
2 35SP3020 ':. 1.50 45 ''. 90 0.6
Fig. 35U 3-Union with Brass Seat
A Size A Packing Weight
Part Number
it ' in in Inner Master lb
'I'll
35U 3010 2.19 20 40 1.0
1 1/4 35U 3012 2.50 15 30 12
1-1/2 35U 3014 2.62 10 20 1.7
2 35U 3020 3.12 6 12 2.4
11/1111
113 SNIITH-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX(323)890-4456 • wwwsmithcooper.com
Pipe Hangers
Fig. 200- "Trimline"Adjustable Band Hanger (B-Line Fig.B317ONF) ®TOLICO
Fig. 200F- "Trimline"Adjustable Band Hanger with Felt Lining (B-Line Fig.B317ONFF)
CC)US
Fig. 200C- "Trimline" Adjustable Band Hanger with Plastic Coated (B-Line Fig.B317ONFC) tin
Fig. 200S - "Trimline"Adjustable Band Hanger with Non-Captured Nut
41>
Size Range: � m
Fig. 200 - 1/2" (15mm)thru 8" (200mm)pipe
Material: Steel, Pre-Galvanized to G90 specifications
Function: For fire sprinkler and other general piping purposes. Knurled --- v
swivel nut design permits hanger adjustment after installation.
Features: ® :_
• (1/2" (15mm)thru 2" (5omm)) Flared edges ease installation for all pipe _ � ...,
• types and protect CPVC plastic pipe from abrasion. Captured design - ���
keeps adjusting nut from separating with hanger. Hanger is easily e
installed around pipe. A
For hanger with non-captured nut order Fig. 200S.
• (21/2" (65mm)thru 8" (2oomm)) Spring tension on nut holds it securely in
hanger before installation.Adjusting nut is easily removed.
Approvals: Underwriters Laboratories listed(1/2" (15mm)thru 8" (200mm)) = Fig.200 /2.200-3/4
in the USA(UL)and Canada(cUL)for steel and CPVC plastic pipe and
Factory Mutual Engineering Approved(FM)(3/4" (20mm)thru 8" (200mm)). Fig.200-1 to 200-2 Fig.200-21/z to 200-6
Conforms to Federal Specifications WW-H-171 E&A-A-1192A,Type 10
and Manufacturers Standardization Society ANSI/MSS SP-69&SP-58, ,,,,,.
Type 10.
Maximum Temperature: 650°F 1343°C) Rss►
Finish: Pre-Galvanized. Stainless Steel ,
materials will be supplied with (2) hex nuts *
iik
in place of a knurl nut
Order By: Figure number and pipe size 1
Designed to meet or exceed requirements of
FM DS 2-0. ,
Fig.200 ''
Fig.200C Fig.200F
Pipe Size Rod Size A B Approx.Wt./100
Part No. in. (mm) in. (mm) in. (mm) lbs. (kg) i. ''''
200-1/2 1/2" (15) 3/8"-16 31/8 (79.4) 25/8" (667) 11 (5.0) A ,
200-3/4 3/4" (201 3/8'-16 31/8" (79.4) 21/2" (63.51 11 (5.0) f ,
200-1 1" (25) 3/8"-16 33/8" (85.7) 25/8" (66.7) 12 (5.5)
200-11/4 11/4" 1321 3/8"-16 33/4" (94.0) 27/8' (73.01 13 (5.9)
" 200-11/2 11/2" (40) 3/e"-16 37/8" (98.4) 27/8" (73.0) 14 (6.4) 4.
200-2 2" 150) 3/8"-16 41/2" 1114.31 3" (76.3) 15 (6.9) {
200-21/2 21/2' (65) 3/8"-16 55/8" (142.9) 41/8" (104.7) 27 (12.3)
200-3 3" 175) 3/a"-16 51/8" (149.1) 4" (101.61 29 (13.3) Fig.200S
200-31h 31/2" (90) 3/8"-16 73/s (187.3) 51/4" (133.3) 34 (15.6)
200-4 4" 11001 3/8"-16 13/8- (187.3) 5" (127.0) 35 (16.0)
200-5 5" (125) 1/2"-13 91/8" (231.8) 61/4 (158.1) 66 (30.2)
200-6 6" 11501 1/2"-13 101/8" (257.2) 63/4" 1171.41 13 133.41
200-8 8" (200) 1/2"-13 131/8" (333.4) 83/4" (222.2) 136 (62.3)
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified.
B-Line
Fire Protection Solutions 21
by E.T•N
r
Threaded Accessories
. B3205 - Threaded Rod (right-hand threads- both ends) (TOLCO Fig.103)
B3205L -Threaded Rod (right&left hand threads) TL %
Size Range: 3/8"-16 thru 3"-4 rod Specify Length ,,,) �����1
Material: Steel
Function: Recommended for use as a hanger support in hanger assemblies. TL�������,
Rod is threaded on both ends with right hand threads of the length shown.Also 11l p
available with left and right hand threads-specify Fig. B3205L when ordering. CThread Size
Maximum Temperature: 750°F(399°C)
Finish: Plain. Contact B-Line for alternative finishes and materials.
Order By: Part number,rod size,length and finish
Standard Design Load
Thread Size Thread Length TL 650°F(343°C) 750°F(399°C)
Part No. A in. (mm) Lbs. (kN) Lbs. (kN)
83205-3/8 X'L' 3/8"-16 21/2" (63.5) 730 (3.25) 572 (2.54)
B3205-1/2 x'L' 1/2"-13 21/2" (63.5) 1350 (6.00) 1057 (4.7(
83205-5/8x'L' 5/8"-11 21/2" (63.5) 2160 (9.61) 1692 (7.52)
B3205-3/4 X'L' ';` 3/4"-10 3" (76.2) 3230 (14.37) 2530 (11.25)
B3205-7/8 x'L' . 7/8"-9 31/2" (88.9) 4480 (19.93) 3508 (15.60)
83206-1 x'L'.; 1"-8 4" (101.6) 5900 (26.24) 4620 (20.55)
133205-11/a x'L' 11/8"-7 41/2" (114.3) 7450 (33.14) 5830 (25.93)
B3205-11/4 x'L' 11/4"-7 5" (127.0) 9500 (42.25) 7440 (33.09)
B3205-11/2 x'L' 11/2"-6 6" (152.4) 13800 (61.38) 10807 (48.07)
B3205-13/4 x'L' `< 13/4"-5 7" (177.8) 18600 (82.73) 14566 (64.79)
83205-2 x'L' ` 2"-41/2 8" (203.2) 24600 (109.42) 19625 (87.29)
83205-21/4x11.' 21/4"-41/2 9" (228.6) 32300 (143.67) 25295 (112.51)
83206-21/2 x'L' 21/2"-4 10" (254.0) 39800 (177.03) 31169 (138.64)
B3205-23/4 x'L' . 23/4"-4 11" (279.4) 49400 (219.73) 38687 (172.08)
B3205-3 x'L' 3"-4 12" (304.8) 60100 (267.32) 47066 (209.35)
ATR -All Threaded Rod 120" (3.05m) Lengths (TOLCO Fig.loo)
Fig. 99-All Threaded Rod Cut To Length
Size Range: 3/8"-16 thru 11/2"-6 rod in 120"(3.05m)lengths or cut to length ������111111`��1111�
Material: Steel 0��>>� N
,s m
Maximum Temperature: 750°F(399°C) ,,,�/� -mo 0
Finish: Plain.Contact B-Line for alternative finishes and materials. - m m
Order By: Part number,rod diameter and finish a
Part No.-Size x Length Threads Recommended Load Approx.Wt./100 Ft.
ATR Fig.99 Per Inch Lbs. (kN) Lbs. (kg)
ATR 1/4"x 120 99-1/4"x length 20 240 (1.07) 12 (5.44)
ATR 3/8"x 120 99-3/a"x length 16 730 (3.24) 29 (13.15)
ATR 1/2"x 120 99-1h"x length 13 1350 (6.00) 53 (24.04)
ATR 5/8"x 120 99-5/"x length 11 2160 (9.60) 89 (40.37)
ATR /4"x 120 .' /4"X length 10 3230 (14.37) 123 (55.79)
ATR 7/8"x 120 99-7/s"x length 9 4480 (19.93) 170 (77.11)
ATR 1"x 120 99-1"x length 8 5900 (26.24) 225 (102.06)
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers&Supports 236 Revised 4/28/2014
B-Line
by ELT•N
P.
SAMMY X-PRESS® SAMMYS
Sammy X Press® , ,.
iProduct Features
11 I(Ye) •The Sammy X-Press expands to provide •Installs in seconds,saving time&
direct vertical attachment in: installation costs.
Patent No. -Metal Deck(22-16 gauge)
.x. 8,935,821
.. -Z-Purlin(18-16 gauge) •Use in applications where access
Vie to the back of the installed fastener is
•The Sammy X-Press Swivel allows you prohibited.ie.metal roof deck,tubular
/1 ,
to hang plumb in extreme roof pitches: steel,or vapor barrier fabric.
(SWXP) -89°in in
45°in metal metal deck for 12/12 pitch •Less jobsite material needed.
Patent Pending
for
(SXP) PXt r Pt11Q •The Sammy X-Press Sidewinder expands •No retaining nut required.
to provide horizontal attachment in:
-16 ga-3/16"steel-purlin,tubular •Provides design flexibility.
or steel.
Patent Pending variant
roof fiches
Rod Pad Ultimate UL Test FM Test Min Max Box Case'
Approvals Size Number Model Description Pullout(lbs) Load(lbs) Load(Ms) Thick Thick Qty Qty -DPikafl?n`
- 4• 1/4' 8181922 XP 200 X-Press 200 1146(22 ga) 185(Luminaire)
250(Luninake) 027
.056' .125' 25 125 Metal Deck
850(2X'Pipe)
0(2'Pipe)
94 .02T
i•I 3/8' 8150922 XP 20 X-Press 20 1146(22 ga) 18S(Luminaire)
ka1475(4'Pipe) .027' .125' 25 125 Metal Deck
250 O.Irnhaire)'' .. .056'
283(Co duh&Cabb)
1500(4'Pipe) .060'
Q. 3/8' 8153922 XP 35 X-Press 35 1783(16 ga) 85(Luminaire) 940 (7 Pipe) 105' .125' 25 125 Purlin
250(Luminaire) 1475(4'PO) .027'
416(Conduit&Cable) .056' i
10-'61 ga Vertical) 170 reNcal(Luminaire)
&It 3/8' 8294922 SXP 20 Swivel X-Press 20 829(45°ort Vertical) 0283 04�� ie�Cable) (7 Pipe) .027' .125' 25 125 Mete Deck
233 045°(Conduit&Cable)
1500(4'Pipe)
165(16 ga Vertical) 250 vertical(Luminaire)
3/8' 8295922 SXP 35 Swr el X-Press 35 1558(8°Off Vertical) 80(4)90°(Luminaire) 635(2'Pipe) .060' 125' 25 125 Pullin
500 vertical(Conduit&Cable)
333 @ 89°(Conduit 8 Cable)
Pr,.PecrSthxvjralConcreteO 3000 pet MefalDeck
— "3/8' .8150922 `XP 20 Sammy X-Press 20 1146(22 pa) 850 PK Ptpe) ''`. "'' 25 125 (Pre-Pour)
Pmt-Par Range 35PCF pia')) Metal Deck
{ r. . e II L- •ost-Pou
H01:'. NI,=L410U`1'
1250(3y:"Pipe)
Q' 3/8' 8293957 SWXP 35 Sidewinder X-Press 35 1798(16 gal 80(Luminaire) .060' .125' 25 125 Purlin
416(Conduk 8 Cable)
Pre-Pour Structural Concrete @ 3000 psi Post-Pour Range II LWCS 35 PCF Obit R')
ii
,ti
If.
Sammy X-Press It® INSTALLATION TOOL
��
",* UXPIT r :� - u # .,�
Patent Pending - '4...... �, - t °-„ Pj r
v
Part Number Model Description Each Qty # k I
8194910 UXPIT° Universal X-PressltTool 1 . -
8195910 RXPIT Retro Socket for 8151910 1 r' '
•
8152910 XPDB 25164°DdiBit 1 • To watch a video demonstration oft he SammyX-Press,visit htlpiNiww.sammysuperscrew.com/sammyxpress.htm
Includes:Sleeve,Bit Receiver,Hex Wrench,and 2584'Drill Bin.
For the most up to date information visa www sarnnrysuperscrew corn 80 -... e
t v