Loading...
The URL can be used to link to this page
Your browser does not support the video tag.
Report
r PS2015-- 6a) t-/ zsT5/„.) � 1 . SEAGATE 1 t Fire Alarm Submittal Package 1 /WO 1 1 i 1 Western States Fire ProtectionC o. rPwtecteaf .deve.4 awe Puoettet a subsidiary of API Group, MC. 13896 Fir Street - Ste. B Oregon City, Or. 97045 ' Dave Keller 503-657-3021 i I I DF-60601:A1 •A1-60 MS-92000DLS(E) Rev 3 8 Are•uTe•ALarms IIntelligent Addressable FACP with Built-In Communicator by Honeywell I - Addressable Fire Alarm Control Panel General I The Fire•Lite MS-92000DLS Rev 3 with Version 5.0 firmware is a combination FACP (Fire Alarm Control Panel) and DACT (Digital Alarm Communicator/Transmitter) all on one circuit board.This compact intelligent addressable control panel has I an extensive list of powerful features. While the MS-92000DLS Rev 3 may be used with an SLC configured in the CLIP(Classic Loop Interface Protocol)mode, it can also operate in LiteSpeedTM mode—Fire•Lite's latest I polling technology—for a quicker device response time. ...0 LiteSpeed's patented technology polls 10 devices at a time. This improvement allows a fully-loaded panel with up to 198 devices to report an incident and activate the notification cir- I cuits in under 10 seconds.With Litespeed polling,devices can be wired on standard twisted,unshielded wire up to a distance of 10,000 feet. MS 9,;'0 OUDL.5 The MS-92000DLS Rev 3's quick-remove chassis protects the I electronics during construction. The backbox can be installed allowing field wiring to be pulled. When construction is com- pleted, the electronics can be quickly installed with just two bolts. R I New features for Rev 3 with Version 5.0 firmware include removable terminal blocks, improved transient protection, .74 74 additional secondary ANN-BUS, and increased power for the ,../ resettable and remote sync outputs. I Available accessories include ANN-BUS devices as well as Features ACS LED, graphic and LCD annunciators, and reverse polar- • Listed to UL standard 864,9th edition. ity/city box transmitter. • The integral DACT transmits system status(alarms,superviso- On-board DACT. I ries,troubles,AC loss, etc.)to a Central Station via the public • Remote site or local USB port upload/download, using PS switched telephone network. It also allows remote and local Tools. programming of the control panel using the PS-Tools Upload/ • Four(4) Style Y (Class B) NAC circuits,which can be con- I Download utility. In addition, the control panel may be pro- grammed or interrogated off-site via the public switched tele ZNAC-92 converter module. (Up to 6.0 amps total NAC phone network.Any personal computer with Windows®XP or power when using optional XRM-24B.) greater, a compatible modem, and PS-Tools—the Fire•Lite . Selectable strobe synchronization for System Sensor, I Upload/Download software kit—may serve as a Service Termi- nal. This allows download of the entire program or upload of • Remote Acknowledge,Silence, Reset and Drill via address the entire program, history file, walktest data, current status able monitor modules or LCD-80F,ANN-80 or Legacy ACS and system voltages. The panel can also be programmed Annunciators. through the FACP's keypad or via a standard PS-2 computer I keyboard,which can be plugged directly into the printed circuit • ANN-BUS for connection to following optional modules(cannot board. This permits easy typing of address labels and other be used if ACS annunciators are used): programming information. —ANN-80(-W)Remote LCD Annunciator I Version 5.0 firmware supports the following:Primary and Sec- ondary ANN-bus devices,AD355(LiteSpeed), USB port, NAC —ANN-S/PG Printer Module circuit diagnostics, a new report has been added to the walk- —ANN-RLY Relay Module test that lists untested devices,new device types added:audio —ANN-LED Annunciator Module telephone type code for ACC 25/50ZST, Photo Supervisory I and auto-resettable Drill(non-latching). —ANNREED Annunciator Module alarms only The FireWatch Series Internet monitoring modules IPDACT-2 —ROME Relay Option Module Enclosure - and IPDACT-2UD permit monitoring of alarm signals over the • ACS/TERM: I Internet saving the monthly cost of two dedicated business —ACS Annunciators: Up to 32 Legacy ACM Series annun- telephone lines. Although not required, the secondary tele- ciators(ACM-16AT or ACM-32 series). Cannot be used if phone line may be retained providing backup communication ANN-BUS devices are used. over the public switched telephone line. —Terminal-mode Annunciators: Up to 32 Legacy LCD-80F I NOTE: Unless otherwise specified, the term MS-92000DLS is remote annunciators. used in this document to refer to both the MS-92000DLS and the MS-92000DLS(E)FACPs(Fire Alarm Control Panels). IDF-60601:Al•12/07/2010—Page 1 of 6 I • EIA-232 printer/PC interface (variable baud rate) on main • Supervisory(yellow) circuit board,for use with optional UL-listed printer PRN-6F. • Alarm Silenced(yellow) I • Integral 80-character LCD display with backlighting. • System Trouble(yellow) • Real-time clock/calendar with automatic daylight savings • Maintenance/Presignal(yellow) control. • Disabled(yellow) • Detector sensitivity test capability(NFPA 72 compliant). • Battery Fault(yellow) I • History file with 1,000-event capacity. • Ground Fault(yellow) • Maintenance alert warns when smoke detector dust accu- mulation is excessive. KEYPAD CONTROLS - I • Automatic device type-code verification. • Acknowledge/Step • One person audible or silent walk test with walk-test log and • Alarm Silence printout. • Drill • Point trouble identification. • System Reset(lamp test) 1 • Waterflow(nonsilenceable)selection per monitor point. • 16-key alpha-numeric pad(similar to telephone keypad) • System alarm verification selection per detector point. • 4 cursor keys • PAS (Positive Alarm Sequence) and presignal delay per • Enter 1 point(NFPA 72 compliant). NOTE:Only detectors may participate in PAS. Product Line Information SLC LOOP: MS-92000DLS: 198-point addressable Fire Alarm Control • SLC can be configured for NFPA Style 4,6,or 7 operation. Panel, one SLC loop. Includes 80-character LCD display, sin- • SLC supports up to 198 addressable devices per loop (99 gle printed circuit board mounted on chassis,and cabinet. 120 detectors and 99 monitor,control,or relay modules). VAC operation. • SLC loop maximum length 10,000 ft.(3,000 m.). MS-92000DLSE: Same as MS-92000DLS, except with 240 See installation manual for wire tables. VAC operation. NOTIFICATION APPLIANCE CIRCUITS(NAGS): 4XTMF Reverse Polarity Transmitter Module: Provides supervised output for local energy municipal box transmitter, • Four onboard NACs with additional NAC capability using alarm,and trouble. I output control modules (CMF 300 or CMF-300-6).The four ZNAC-92: Optional converter module which converts four (4) Class B NACs can be converted to four Class A NACs with Style Y(Class B) NAC circuits to four(4) Style Z(Class A)cir- optional ZNAC-92 converter module. cults. • Silence Inhibit and Auto Silence timer options. • Continuous, March Time, Temporal or California code for PK-CD Programming software for Windows®-based PC com- main circuit board NACs with two-stage capability. puter(cable not included),available on www.firelite.com. • Selectable strobe synchronization per NAC. DP-9692:Optional dress panel for MS-92000DLS Rev 3. • 2.5 amps maximum per each NAC circuit. TR-CE:Optional trim Ring for semi-flush mounting. I NOTE:Maximum 24VDC system power output is shared among BB-26: Battery backbox, holds up to two 25 AH batteries and all NAC circuits and 24VDC special-application auxiliary power CHG-75. outputs. Total available output is 3.0 amps. Using the optional BB-55F:Battery box,houses two 55 AH batteries. I XRM-24B transformer increases 24VDC output to 6.0 amps. PROGRAMMING AND SOFTWARE: CHG-75: Battery charger for lead-acid batteries with a rating of 25 to 75 AH. • Autoprogram(learn mode)reduces installation time. CHG-120F:Remote battery charging system for lead-acid bat- • Custom English labels(per point)may be manually entered teries with a rating of 55 to 120 AH. Requires additional BB- I or selected from an internal library file. 55F for mounting. • Three Form-C relay outputs(two programmable). BAT Series:Batteries,see data sheet DF-52397. • 99 software zones. XRM-24B(E): Optional transformer. Increases system power • Continuous fire protection during online programming at the output to 6.0 amps. Use XRM-24BE with MS-92000DLS Rev front panel. 3(E). • Program Check automatically catches common errors not PRT/PK-CABLE: Cable printer/personal computer interface linked to any zone or input point. cable; required for printer or for local upload/download pro- • OFFLINE PROGRAMMING: Create the entire program in gramming and updating panel firmware. your office using a Windows based software package PRN-6F: UL listed compatible event printer. Uses tractor-fed (order programming kit PS-Tools, separately). Upload/ I download system programming locally to the MS- Paper.T 2 92000DLS Rev 3 in less than one minute. IPDAC /2UD, IPDACT Internet Monitoring Module: • USB upload/download programming with standard Male-A Mounts in bottom of enclosure with optional mounting kit (PN to Male-B cable. IPBRKT). Connects to primary and secondary DACT tele- phone output ports for internet communications over customer User Interface provided ethernet internet connection. Requires compatible Teldat VisorALARM Central Station Receiver. Can use DHCP LED INDICATORS or static IP. (See data sheet DF-60407 or DF-52424 for more • AC Power(green) information.) 1 • Fire Alarm(red) Page 2 of 6—DF-60601:A1•12/07/2010 1 I IPBRKT: Mounting kit for IPDACT-2/2UD in common enclo- DNRW: Innovair Flex low-flow non-relay duct-detector hous- ' sure. ing, with NEMA-4 rating. Watertight. (Order SD355R sepa- rately.) Y-adaptor option allows connection of both panel rately.) dialer outputs to one IPDACT-2/2UD cable input. MMF-300: Addressable Monitor Module for one zone of nor- mally-open dry-contact initiating devices. Mounts in standard COMPATIBLE ANNUNCIATORS 4.0" (10.16 cm.) box. Includes plastic cover plate and end-of- ANN-80(-W): LCD Annunciator is a remote LCD annunciator line resistor. Module may be configured for either a Style B that mimics the information displayed on the FACP LCD dis- (Class B)or Style D(Class A)IDC. play. Recommended wire type is un-shielded. (Basic model is MDF-300: Dual Monitor Module. Same as MMF-300 except it I • red;order-W version for white;see DF-52417.) provides two Style B(Class B)only IDCs. ANN-LED: Annunciator Module provides three LEDs for each MMF-301: Miniature version of MMF-300. Excludes LED and zone: Alarm, Trouble and Supervisory. Ships with red enclo- Style D option. Connects with wire pigtails. May mount in sure(see DF-60241). device backbox. I ANN-RLED: Provides alarm (red) indicators for up to 30 input MMF-302: Similar to MMF-300,but may monitor up to 20 con- ventional or addressable points.(See DF-60241). ventional two-wire detectors. Requires resettable 24 VDC ANN-RLY: Relay Module, which can be mounted inside the power.Consult factory for compatible smoke detectors. I cabinet, provides 10 programmable Form-C relays. (See DF- 52431.) ROME: Relay Option Module Enclosure. Provides one ANN- RLY Relay Module already installed. The ROME Series pro- I vides mounting space for one additional Relay Module or one addressable Multi-module. (See Installation Sheet PN 53530.) ANN-S/PG:Serial/Parallel Printer Gateway module provides a connection for a serial or parallel printer.(See DF-52429.) I ANN-I/O: LED Driver Module provides connections to a user supplied graphic annunciator.(See DF-52430.) ACM-8RF: Relay module provides 8 Form-C 5.0 amp relays. I ACS-LED Zone Series:LED-type fire annunciators capable of providing up to 99 software zones of annunciation.Available in increments of 16 or 32 points to meet a variety of applications. I - LDM Series: Lamp Driver Module series for use with custom graphic annunciators. LCD-80F 80F (Liquid Crystal Display) point annunciator: 80-character, backlit LCD-type fire annunciators capable of I displaying English-language text. NOTE:For more information on Compatible Annunciators for use with the MS-92000DLS Rev 3,see the following data sheets(doc- ument numbers) ACM-8RF (DF-51555), ACS/ACMSeries (DF- 52378),LDM Series(OF-51384),LCD-80F(DF-52185). ' LITESPEED COMPATIBLE ADDRESSABLE DEVICES All feature a polling LED and rotary switches for addressing. I CP355:Addressable low-profile ionization smoke detector. SD355:Addressable low-profile photoelectric smoke detector. SD355T: Addressable low-profile photoelectric smoke detec- I tor with thermal sensor. SD355R: Addressable remote test capable detector for use with D355PL or DNR(W)duct smoke detector housings. H355: Fast-response,low-profile heat detector. NI II H355R: Fast-response, low-profile heat detector with rate-of- rise option. H355HT: Fixed high-temperature detector that activates at 190F/88C. AD355(A): Low-profile, intelligent,"Adapt"multi-sensor detec- tor(B350LP base included). I BEAM355: Intelligent beam smoke detector. BEAM355S: Intelligent beam smoke detector with integral sensitivity test. D355PL: Innovair Flex low-flow non-relay duct-detector hous- Iing.SD355R included. DF-60601:Al•12/07/2010—Page 3 of 6 1 1 CMF-300: Addressable Control Module for one Style Y/Z (Class B/A) zone of supervised polarized Notification Appli- I ances. Mounts directly to a 4.0" (10.16 cm.) electrical box. Notification Appliance Circuit option requires external 24 VDC to power notification appliances. CRF-300: Addressable relay module containing two isolated sets of Form-C contacts, which operate as a DPDT switch. Mounts directly to a 4.0"(10.16 cm.)box,surface mount using --- the SMB500. BG-12LX:Addressable manual pull station with interface mod- • MS-92000DLS Remote ACC-25/50(ZS/T) ule mounted inside. Are Alarm Microphone Audio Command Control Panel Center 1300: Fault Isolator Module.This module isolates the SLC loop from short circuit conditions (required for Style 6 or 7 opera- 1118 tion). lIt u) SPR peaker o SMB500:Used to mount all modules except the MMF-301 and 1 N M301. SD355 --� -- SPCMMF-300-10: Ten-input monitor module. Mount one or two II Photo Detector , ,• Series modules in a BB-2F cabinet (optional). Mount up to six mod- - ,.i' Speaker ules on a CHS-6 chassis in a BB-6F. LCD-80F MMF-302-6:Six-zone interface module for compatible conven- tional two-wire detectors. Mount one or two modules in a BB- 2F cabinet (optional). Mount up to six modules on a CHS-6 I AD355 SPS chassis in a BB-6F. Adapt Detector Series speaker/Strobe CMF-300-6: Six-circuit supervised control module. Mount one 1 or two modules in a BB-2F cabinet(optional). Mount up to six ANN-80 modules on a CHS-6 chassis in a BB-6F. CRF-300-6: Six Form-C relay control module. Mount one or H355/H355R/H355HT two modules in a BB-2F cabinet (optional). Mount up to six Heat Detector modules on a CHS-6 chassis in a BB-6F. P2R NOTE: 1)For more information on Compatible Addressable Strobe Devices for use with the MS-92000DLS Rev 3, see the following - 11 data sheets (document numbers):AD355 (DF-52324), BG-12LX I (DF-52013), CMF-300-6 (DF-52365), CRF-300-6 (DF-60379), MDF-300 CMF/CRF Series (DF-52130), CP355 (DF-52383), D355PL (DF- Dual Monitor Module xa 52398), H355 Series (DF-52385), 1300 (DF-52389), MMF-300 - Series/MDF-300 (DF-52121), MMF-300-10 (DF-52347), MMF- P2R 302-6 (DF-52356), SD355/SD355T (DF-52384). 2)Legacy 300 , �— Strobe Series detection devices such as the CP300/CP350, SD300(T)/ Power Supply SD350(T) and older modules such as the M300, M301, M302, SD355T FCPS-24FS6 C304,and BG-10LX are not compatible with LiteSpeed polling.If FCPS-24FS8 rg the SLC contains one of these devices, pollingmust be set for I Photo/Thermal standard LiteSpeed protocol. Please consult factory for further P2R information on previous 300 Series devices. 111-11111 Strobe Wiring Requirements MMF-300 Multi-Modules1 Monitor Module While shielded wire is not required, it is recommended that all • CRF-300-6 Six-Relay Control Module SLC wiring be twisted-pair to minimize the effects of electrical • CMF-300-6 Six-Circuit Supervised Control Module interference. Wire size should be no smaller than 18 AWG II • MMF-302-6 Six-Zone Interface Module (0.78 mm2) and no larger than 12 AWG (3.1 mm2). The wire • MMF-300-10 Ten Input Monitor Module size depends on the length of the SLC circuit. Refer to the MMF-302 panel manual for wiring details. 2-Wire Detector \\4111111;f Monitor Module 1 D355PL Beam Detector/Beam 355 Duct Detector ' I FIFE MS-92000DLS ADDRESSABLE FIRE ALARM I BG-12LXAddressable CONTROL PANEL - Manual Pull Station 1 Page 4 of 6—DF-60601:A1•12/07/2010 1 I SYSTEM SPECIFICATIONS I System Capacity 16.65" (42.29 cm.)wide x 5.20" (13.34 cm.) deep. Trim Ring (TR-CE):22.00"(55.88 cm.)high x 19.65"(49.91 cm.)wide. • Intelligent Signalling Line Circuits 1 • Addressable device capacity 198 Shipping Specifications • Programmable software zones 99 Weight:26.9 lbs. (12.20 kg.) Dimensions:20.00"(50.80 cm.) I • • ACS Annunciators 32 high x 22.5"(57.15 cm.)wide x 8.5"(21.59 cm.)deep. • ANN-bus devices 16 Temperature and Humidity Ranges Electrical Specifications This system meets NFPA requirements for operation at 0 — AC Power: MS-92000DLS Rev 3: 120 VAC,60 Hz, 3.0 amps. 49°C/32 — 120°F and at a relative humidity 93% ± 2% RH MS-92000DLS Rev 3E:240 VAC,5 0 Hz, 1.5 amps.Wire size: (noncondensing) at 32°C ± 2°C (90°F ± 3°F). However, the minimum 14 AWG(2.00 mm2)with 600 V insulation. useful life of the system's standby batteries and the electronic I Battery charger capacity: 7 AH - 18 AH batteries. Up to two components may be adversely affected by extreme tempera- 18 Ah batteries can be housed in the FACP cabinet. Larger ture ranges and humidity. Therefore, it is recommended that batteries require an external battery charger such as the CHG this system and its peripherals be installed in an environment 75 or CHG-120, and a separate battery cabinet such as the with a normal room temperature of 15—27°C/60—80°F. I BB-26 or NFS-LBB. Communication Loop:Supervised and power-limited. NFPA Standards Notification Appliance Circuits: Each terminal block pro- The MS-92000DLS Rev 3 complies with the following NFPA I vides connections for two Style Y (Class B) for a total of four 72 Fire Alarm Systems requirements: Style Y (Class B) or with an optional ZNAC-92 module con- verts to four Style Z(Class A) NACs. Maximum signaling cur- Supervisory). rent per circuit:2.5 amps. End-of-Line Resistor:4.7K ohm, 1/2 —AUXILIARY(Automatic, Manual and Waterflow) (requires I watt(P/N 71252 UL listed)for Style Y(Class B)NAC. Refer to 4XTMF). _ panel documentation and Fire•Lite Device Compatibility Docu- REMOTE STATION (Automatic, Manual, Waterflow and ment for listed compatible devices. Sprinkler Supervisory) (Where a DACT is not accepted, _ Two Programmable Relays and One Fixed Trouble Relay: the alarm, trouble and supervisory relays may be con I Contact rating:2.0 amps @ 30 VDC(resistive),0.5 amps 0 30 VAC(resistive). Form-C relays. nected to UL 864 listed transmitters. For reverse polarity signaling of alarm and trouble,4XTMF is required.) Special Application Non-resettable Power(24 VDC Nomi- —PROPRIETARY (Automatic, Manual, Waterflow and nal): Jumper selectable (JP4) for conversion to resettable Sprinkler Supervisory). I power output. Up to 1.0 amp total DC current available from each output.Power limited. —CENTRAL STATION (Automatic, Manual, Waterflow and Sprinkler Supervisory). Special Application Resettable Power (24 VDC nominal): —OT, PSDN (Other Technologies, Packet-switched Data Jumper selectable (JP6) for conversion to non-resettable Network) I power. Up to 1.0 amp total DC current available. Refer to the Fire•Lite Device Compatibility Document for listed compatible Agency Listings and Approvals devices. Remote Sync Output: Remote power supply synchronization The listings and approvals below apply to the basic MS- output. Nominal special application power:24 VDC. Maximum ules920may notS Rev 3 control panel. In some cases, certain mod- current: 300 mA. End-of-Line Resistor: 4.7K ohm. Output ules may be listed by certain approval agencies, or listing linked to NAC 1 control.Supervised and power limited. may be in process.Consult factory for latest listing status. • Telephone Interface: Unless used with Teldat VISORALARM, UL Listed:S624 I requires dedicated business telephone number with a mini- • FM approved mum of 5 volts DC(off-hook voltage). Obtain dedicated phone • CSFM:7165-0075:0208 line directly from your local phone company.Do not use shared • MEA: 120-06-E I phone lines or PBX(digital)type phone line extensions. For ULC-listed version,see DF-60599. Cabinet Specifications Door: 19.26" (48.92 cm.) high x 16.82" (42.73 cm.) wide x FireLite®Alarms®is a registered trademark of Honeywell International Inc. I 0.12" (.30 cm.) deep. Backbox: 19.00" (48.26 cm.) high x Wheelock®is a registered trademark of and ExcederT'" Is a trademark of Cooper Notification. 02010 by Honeywell International Inc.All rights reserved.Unauthorized use . of this document is strictly prohibited. I This document is not intended to be used for installation purposes. :::::•:•:.: • ISO 9001 We try to keep our product information up-to-date and accurate. ilii C E R T F 1 E O We cannot cover all specific applications or anticipate all requirements. IBMWii` 11M1 All specifications are subject to change without notice. 1 . ISALITT SYSTEMS Made in the U.S.A. For more information,contact Fire•Lite Alarms.Phone:(800)627-3473,FAX:(877)699-4105. www.firelite.com Page 6 of 6—DF-60601:Al•12/07/2010 I 1 1 1 / I 1 I 1 I I 1 1 1 DF-60601:Al•12/07/2010—Page 5 of 6 Idf-52417:c•B-90 ANN-80 8 Flre•LITe•ALarms I 80-Character LCD Serial Annunciator by Honeywell I - Annunciators General I • The ANN-80 annunciator is a compact, backlit, 80-character LCD fire annunciator that mimics the Fire Alarm Control Panel (FACP) display. It provides system status indicators for AC Power, Alarm,Trouble, Supervisory, and Alarm Silenced condi- !' tions.The ANN-80 and the FACP communicate over a two-wire serial interface employing the ANN-BUS communication format. Connected devices are powered, via two additional wires, by either the host FACP or a remote UL-listed,filtered power supply. I ANN-80 is red;for white,order ANN-80-W. 0 The ANN-80 displays English-language text of system point information including device type, zone, independent point alarm, trouble or supervisory status, as well as any custom alpha labels programmed into the control panel. It includes °•"'R u� arms con- trol switches for remote control of critical system functions. (A byueHoneywealecf, keyswitch prevents unauthorized operation of the control $ �jF ` switches.) I Up to eight ANN-80s may be connected to the ANN-BUS of = --- each FACP. No programming is required,which saves time dur- ing system commissioning. I Features • Listed to UL Standard 864,9th Edition. • Backlit 80-character LCD display(20 characters x 4 lines). • Supervisory - • • Mimics all display information from the host panel. Alarm Silenced I • Control switches for System Acknowledge, Signal Silence, Drill,and Reset. Specifications • Control switches can be independently enabled or disabled • Operating voltage range: 18 VDC to 28 VDC. I at the FACP. Current consumption 24 VDC nominal(filtered and non • • Keyswitch enables/disables control switches and mechani- cally locks annunciator enclosure • Ambient temperature:32°F to 120°F(0°C to 49°C). • Keyswitch can be enabled or disabled at the FACP. • Relative humidity: 93%±2% RH (noncondensing)at 32°C I • Enclosure supervised for tamper. ±2°C(90°F±3°F). • System status LEDs for AC Power, Alarm, Trouble, Supervi- • 5.375" (13.65 cm.) high x 6.875" (17.46 cm.) wide x 1.375" sory,and Alarm Silence. (3.49 cm.)deep. • Local sounder can be enabled or disabled at the FACP. • For use indoors in a dry location. I • ANN-80 connects to the ANN-BUS terminal on the FACP and • All connections are power-limited and supervised. requires minimal panel programming. • Displays device type identifiers, individual point alarm, trou- Agency Listings and Approvals I ble,supervisory,zone,and custom alpha labels. Time-and date display field. The listings and approvals below apply to the ANN-80. In some • cases, certain modules may not be listed by certain approval • Surface mount directly to wall or to single, double, or 4" agencies,or listing may be in process.Consult factory for latest square electrical box. listing status. 1 • Semi-flush mount to single, double, or 4" square electrical • UL•S2424 box.Use ANN-SB8OKIT for angled view mounting. • Can be remotely located up to 6,000 feet(1,800 m)from the • FM approved panel. • CSFM:7120-0075:211 • Backlight turns off during AC loss to conserve battery power • MEA:442-06-E but will turn back on if an alarm condition occurs. • May be powered by 24 VDC from the host FACP or by remote The ANN-BUS power supply(requires 24 VDC). I • Up to eight ANN-80s can be connected on the ANN-BUS. POWERING THE DEVICES ON THE ANN-BUS FROM AUXILIARY POWER SUPPLY • Controls and Indicators The ANN-BUS can be powered by an auxiliary power supply when the maximum number of ANN-BUS devices exceeds the 1 • AC Power • Alarm ANN-BUS power requirements.See the FACP manual for more information. • Trouble 1 df-52417:c•05/22/09—Page 1 of 2 1 ANN-BUS DEVICE ADDRESSING After calculating the total worst case current draw,the following Each ANN-BUS device requires a unique address (ID Number) table specifies the maximum distance the modules can be in order to communicate with the FACP.A maximum of 8 devices located from the FACP on a single wire run.The table ensures can be connected to the FACP ANN-BUS communication circuit. 6.0 volts of line drop maximum.In general,the wire length is lim- See the FACP manual for more information. ited by resistance, but for heavier wire gauges, capacitance is the limiting factor. I WIRE REQUIREMENTS:COMMUNICATIONS CIRCUIT These cases are marked in the chart with an asterisk(•). Maxi- The ANN-80 connects to the FACP ANN-BUS communications mum length can never be more than 6,000 feet (1,800 m), circuit. To determine the type of wire and the maximum wiring regardless of gauge used. See table below. distance that can be used with FACP ANN-BUS accessory mod- ules, it is necessary to calculate the total worst case current draw for all modules on a single 4-conductor bus.The total worst • 14 to 18 AWG (0.75-2.08 mm2)wire for 24 VDC power cir- case current draw is calculated by adding the individual worst cuit is acceptable.Power wire distance limitation is set by 1.2 case currents for each module. volt maximum line drop form source to end of circuit. NOTE: For total worst case current draw on a single ANN-BUS • All connections are power-limited and supervised. refer to appropriate FACP manual. • A maximum of eight ANN-80 modules may be connected to this circuit. Communication Pair Wiring Distance: FACP to Last ANN-BUS Module 1 Total Worst Case 22 Gauge 18 Gauge 16 Gauge 14 Gauge Current Draw(amps) i 0.100 1,852 ft. 4,688 ft. •6,000 ft. *6,000 ft. 0.200 926 ft. 2,344 ft. 3,731 ft. 5,906 ft. 0.300 617 ft. 1,563 ft. 2,488 ft. 3,937 ft. 0.400 463 ft. 1,172 ft. 1,866 ft. 2,953 ft. 0.500 370 ft. 938 ft. 1,493 ft. 2,362 ft. 0.600 309 ft. 781 ft. 1,244 ft. 1,969 ft. I 0.700 265 ft. 670 ft. 1,066 ft. 1,687 ft. 0.800 231 ft. 586 ft. 933 ft. 1,476 ft. - 0.900 206 ft. 521 ft. 829 ft. 1,312 ft. I 1.000(max.) 185 ft. 469 ft. 746 ft. 1,181 ft. WIRING CONFIGURATION ORDERING OPTIONS: The following figure illustrates the wiring between the FACP and ANN-80:Red 80 character LCD Annunciator. I ANN-BUS devices. ANN-80-W:White,80 character LCD Annunciator. ANN-BUS and power ANN-SB8OKIT-R: Red surface mount backbox with angled wiring are supervised wedge. and power-limited. I ANN-SB8OKIT W: White surface mount backbox with angled ® n wedge. Tel OOUO 4 3 2 1 ANN-BUS Device ralidluiliA I MS-9050UD Coea p p Q Q CO CO O 783 1 2 3 4 5 6 7 8 FACP Wiring to ANN-BUS Device I FireLite®Alarms is a registered trademark of Honeywell International Inc. ©2009 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. :.:.;� I Iso 9001 We try to keep our product information up-to-date and accurate. :::::::::::� C E R T 1 F 1 E O We cannot cover all specific applications or anticipate all requirements. EMME R I WOW= All specifications are subject to change without notice. I QUALITY SYSTEMS Made in the U.S.A. For more information,contact Fire•Lite Alarms.Phone:(800)627-3473,FAX:(877)699-4105. www.firelite.com Page 2 of 2—df-52417:c•05/22/09 1 IDF-52384:C•E-160 SD355(A) Series rzj FlI'e•LITe®ALat''t'Y1S I Addressable Photoelectric Smoke Detectors by Honeywell I - Addressable Devices General I - The SD355(A), SD355T(A), and SD355R(A)addressable, low- profile plug-in photoelectric detectors use a state-of-the-art pho- toelectric sensing chamber with communications to provide open area protection and are used exclusively with Fire•Lite's111> I/ I Addressable Fire Alarm Control Panels (FACPs). The SD355T(A)adds thermal sensors that will alarm at a fixed tem- perature of 135°F (57°C). Since these detectors are address- -- 9 able, they will help emergency personnel quickly locate a fire I during its early stages, potentially saving precious rescue time while also reducing property damage. Two LEDs on each sen- sor444.1"•# light to provide a local, visible sensor indication. Remote LED annunciator capability is available as an optional acces- R sory, PN RA100Z(A).The SD355R(A) is a remote test capable I detector for use with D355PL(A)or DNR(A)/DNRW duct smoke e detector housings. SD355(A) in B210LP(A) Base gi I Features SLC loop Applications • Two-wire loop connection. Use photoelectric detectors in life-safety applications to provide • Unit uses base for wiring. a broad range of fire-sensing capability, especially where smol- I Addressing Bering fires are anticipated. Ionization detectors are often better • Addressable by device. than photoelectric detectors at sensing fast,flaming fires. - • Rotary, decimal addressing: 01 – 99 with MS-9200 series, I and 01 –159 with MS-9600 series. Construction Architecture These detectors are constructed of off-white fire resistant pias- • Unique single-source, dual-chamber design to respond tic. SD355(A) series plug-in, low-profile smoke detectors are quickly and dependably to a broad range of fires. designed to commercial standards and offer an attractive I • Sleek,low-profile design. appearance. • Integral communications and built-in type identification. Installation • Built-in tamper-resistant feature. I • Removable cover and insect-resistant screen for simple field SD355(A) series plug-in detectors use a detachable mounting cleaning. base to simplify installation,service and maintenance. Operation Mount base(all base types)on an electrical backbox which is at • Withstands air velocities up to 4,000 feet-per-minute (20 m/ least 1.5" (3.81 cm) deep. For a chart of compatible junction I sec.)without triggering a false alarm. boxes,see DF-60059. • Factory preset at 1.5% nominal sensitivity for panel alarm NOTE:Because of the inherent supervision provided by the SLC threshold level. loop, end-of-line resistors are not required. Wiring 'T-taps" or branches are permitted for Style 4 (Class B) wiring. SD355R(A) • Visible LED"blinks"when the unit is addressed(communicat- mounts in a D355PL(A)or DNR(A)/DNRW duct detector housing. I ing with the fire panel)and latches on in alarm. Mechanicals Operation • Sealed against back pressure. Each SD355(A) series detector uses one of 99 possible I • Direct surface mounting or electrical box mounting. addresses on the MS-9200 series and up to 318 (159 on each • Mounts to:single-gang box,3.5"(8.89 cm)or 4.0"(10.16 cm) loop) on the MS-9600 series Signaling Line Circuit (SLC). It octagonal box,or 4.0"(10.16 cm)square electrical box(using responds to regular polls from the system and reports its type a plaster ring—included). and status. I Other system features The addressable photoelectric sensor in the SD355(A) series • Fully coated circuit boards and superior RF/transient protec- has a unique unipolar chamberthat responds quickly and uni- tion. formly to a broad range of smoke conditions. It can withstand • • 94-VO plastic flammability rating. wind gusts up to 4,000 feet-per-minute (20 m/sec.) without • Low standby current. sending an alarm level signal. Because of its unipolar chamber, Options the SD355(A) series is approximately two times more respon- sive than most photoelectric sensors.This makes it a more sta- • Remote LED output connection,PN RA100Z(A). ble detector. I IDF-52384:C•12/07/2011—Page 1 012 • 1 Detector Sensitivity Test INTELLIGENT BASES Each detector can have its sensitivity tested(required per NFPA NOTE: A"suffix indicates ULC Listed model. 72, Chapter 14 on Inspection, Testing and Maintenance) when NOTE: The detector's plug-in base can be changed off for special installed/connected to a MS-9200 series or MS-9600 series applications. For details about intelligent bases and their mount- addressable fire alarm control panel.The results of the sensitiv- ing,see DF-60059. ity test can be printed off the MS-9200 series or MS-9600 series B210LP(A): Plug-in detector base (included); standard U.S. for record keeping. flanged low-profile mounting base. Specification B210LPBP:Bulk pack of B210LP;package contains 10. B501(A):Standard European flangeless mounting base. Voltage range: 15—32 VDC(peak). B501 BP:Bulk pack of B501;package contains 10. Standby current:300 pA o 24 VDC. B200SR(A): Intelligent sounder base capable of producing LED current:6.5 mA CO 24 VDC(latched"ON"). sound output with ANSI Temporal 3 or continuous tone. Air velocity:4,000 ft./min.(20 m/sec.)maximum. Replaces B501 BH series bases in retrofit applications. Size:2.1"(5.33 cm)high;base determines diameter. B224RB(A): Plug-in System Sensor relay base. Screw termi- nals:—B210LP(A):6.1"(15.5 cm)diameter. up to 14 AWG (2.0 mm2). Relay type: Form-C. Rating:2.0 A @ 30 VDC resistive;0.3 A @ 110 VDC inductive; 1.0 A @ 30 —B501(A):4.1"(10.4 cm)diameter. VDC inductive. —B200SR(A):6.875"(17.46 cm)diameter. B224B1(A): Plug-in System Sensor isolator detector base. —B224RB(A):6.2"(15.748 cm)diameter. Maximum 25 devices between isolator bases(see DF-52389). Weight:3.6 oz.(102 g). ACCESSORIES Operating temperature range: for SD355(A): 0°C to 49°C F110: Retrofit flange to convert B210LP(A) to match the (32°F to 120°F); for SD355T(A):0°C to 38°C (32°F to 100°F). B350LP(A)profile,or to convert older high-profile bases to low- SD355R(A):installed in a DNR(A)/DNRW-20°C to 70°C (-4°F profile. to 158°F). F110BP:Bulk pack of F110;package contains 15. Temperature:0°C—49°C(32°F—120°F). F210:Replacement flange for B210LP(A)base. Relative humidity: 10%—93%,non-condensing. RA100Z(A):Remote LED annunciator.3—32 VDC.Mounts to a U.S. single-gang electrical box. For use with B501(A) and Listings B210LP(A)bases only. Listings and approvals below apply to the SD355(A), SMB600:Surface mounting kit SD355T(A),and SD355RT(A)detectors. In some cases,certain M02-04-00:Test magnet. modules may not be listed by certain approval agencies,or list- ing may be in process.Consult factory for latest listing status. M02-09-00:Test magnet with telescoping handle. • UL Listed:S1059. XR2B:Detector removal tool.Allows installation and/or removal • ULC Listed S1059. of detector heads from bases in high ceiling applications. • CSFM:7272-0075:0194. XP-4:Extension pole for XR2B.Comes in three 5-foot(1.524 m) • MEA:243-02-E. sections. • FM approved. T55-127-010:Detector removal tool without pole. BCK-200B: Black detector covers for use with SD355(A) only; Product Line Information box of 10. , WCK-200B: White detector covers for use with SD355(A)only; NOTE:"A"suffix indicates ULC Listed model. box of 10. SD355: Adressable photoelectric detector; B210LP base included. SD355A: Sames as SD355 with ULC Listing; B210LPA base included. SD355T: Same as SD355 but with thermal element; B210LP base included. SD355TA: Same as SD355T with ULC Listing; B210LPA base included. SD355R: Remote test capable addressable photoelectric detec- tor for use with a D355PL(A) or DNRA/DNRW duct detector housing;B210LP base included. SD355RA: Same as SD355R with ULC Listing for use with a D355PLA or DNRA duct detector housing; B210LPA base included. Fire•Lite®Alarms is a registered trademark of Honeywell International Inc. ©22011 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. ISO9001 We try to keep our product information up-to-date and accurate. CER T I F 1 E U We cannot cover all specific applications or anticipate all requirements. 9111111311111 I MAIRCHIMIS All specifications are subject to change without notice. MMALITY SYSTEMS Made in the U.S.A. For more information,contact Fire•Lite Alarms.Phone:(800)627-3473,FAX:(877)699-4105. www.firelite.com Page 2 of 2—DF-52384:C•12/07/2011 1 IDF-52385:D•E-710 I H355(A) Series Flf'�e•LITt3•AL1'Y1S Intelligent Addressable ar Thermal Detectors by Honeywell I - Addressable Devices General I - The Flre•Lite Alarms H355(A) Series thermal detectors are addressable sensors that use a state-of-the-art thermistor sensing circuit for fast response.These sensors provide open- area protection and are intended for use with Fire•Lite's A II I addressable Fire Alarm Control Panels(FACPs). The H355(A) and H355R(A) sensors provide fixed tempera .— //, - ture alarm detection at 135°F (57°C). The H355R(A) sensor I also responds to rate-of-rise conditions of greater than 15°F (8.3°C) per minute. The H355HT(A) is a fixed high-tempera- ture detector that activates at 190°F (88°C). These thermal 114111.1. detectors provide addressable property protection in a variety of applications. a I Two LEDs on each sensor light to provide a local,visible sen- H355(A) in B210LP(A) Base sor indication. Remote LED annunciator capability is available using an optional accessory,the RA100Z. • 94-5V plastic flammability rating. IFeatures Options: SLC loop: • Remote LED output connection to optional RA100Z remote LED annunciator. I • Two-wire SLC loop connection. Flanged surface mounting kit. • Unit uses base for wiring. • Addressing: Installation • Addressable by device. H355(A) Series plug-in intelligent thermal detectors use a • Rotary,decimal addressing:01 —159 with MS-9600 series, detachable base to simplify installation, service and mainte- 01 —99 with MS-9200 series. nance. Installation instructions are shipped with each detector. - Architecture: Mount base(all base types)on an electrical backbox which is • Sleek,low-profile,stylish design. at least 1.5"(3.81 cm)deep. For a chart of compatible junction • State-of-the-art thermistor technology for fast response. boxes,see DF-60059. • Integral communications and built-in device-type identifica- NOTE:Because of the inherent supervision provided by the SLC Ition. loop, end-of-line resistors are not required. Wiring "T-taps" or • Built-in tamper resistant feature. branches are permitted for Style 4(Class B)wiring only. • Built-in functional test switch activated by external magnet. Applications Operation: I • Factory preset at 135°F (57°C) for the H355(A) and Use thermal detectors for protection of property. H355R(A); 190°F(88°C)for the H355HT(A). Construction • Rate-of-rise triggers at 15°F (8.3°C) per minute for the I H355R(A). These detectors are constructed of off-white fire-resistant • 360°-field viewing angle of the visual alarm indicators (two plastic. The H355(A) Series plug-in intelligent thermal detec- tors are designed to commercial standards and offer an attrac- tiveon steady red in Alarm. appearance. I • Visible LEDs"blink"every time the unit is addressed. Operation Mechanicals: Each H355(A) Series detector uses one of 159 (MS-9600 • Sealed against back pressure. series) or 99 (MS-9200 series) possible addresses on a con- I • SEMS screws for wiring of the separate base. • Designed for direct-surface or electrical box mounting. trot panel SLC loop. It responds to regular polls from the con- trol panel and reports its type and the status. If it receives a Plugs into separate base for ease of installation and main- test command from the panel(or a local magnet test), it stimu- • • tenanclates its electronics and reports an alarm. It blinks its LEDs when polled and turns the LEDs on when commanded by the • Separate base allows interchange of photoelectric, ioniza panel. The H355(A) Series offers features and performance tion and thermal sensors. that represent the latest in thermal detector technology. - Other system features: I • Remote test feature from the panel. • Walk test with address display. • Low standby current. IDF-52385:D•5/17/2013—Page 1 of 2 1 Spefications INTELLIGENT BASES Size:2.1"(5.3 cm)high;base determines diameter. NOTE:"A"suffix indicates ULC Listed model. I —B210LP(A) 6.1"(15.5 cm)diameter. NOTE:The detector's plug-in base can be changed off for special applications. For details about intelligent bases and their mount- -B501(A):4.1"(10.4 cm)diameter. ing,see DF-60059. —B200SR(A):6.875"(17.46 cm)diameter. B210LP(A): Plug-in detector base (included); standard U.S. -B224RB(A):6.2"(15.748 cm)diameter. flanged low-profile mounting base. Shipping weight:4.8 oz.(137 g). B210LPBP:Bulk pack of B210LP;package contains 10. Installation temperature: B501(A):Standard European flangeless mounting base. - 1 —H355(A),H355R(A):—4°F to 100°F(-20°C to 38°C). B501BP:Bulk pack of B501;package contains 10. —H355HT(A):—4°F to 150°F(-20°C to 66°C). B200SR(A): Intelligent sounder base capable of producing Humidity range: 10% to 93% relative humidity (noncon- sound output with ANSI Temporal 3 or continuous tone. densing). Replaces B501BH series bases in retrofit applications. Voltage range: 15 to 32 VDC peak. B224RB(A): Plug-in System Sensor relay base. Screw termi- Standby current: 300 pA @ 24 VDC (one communication nals:up to 14 AWG(2.0 mm2).Relay type:Form-C.Rating:2.0 every five seconds with LED blink enabled). A © 30 VDC resistive; 0.3 A © 110 VDC inductive; 1.0 A 30 VDC inductive. LED current:6.5 mA @ 24 VDC. B224B1(A): Plug-in System Sensor Isolator detector base. Mounting: B210LP(A) flanged base, included. See "Product Maximum 25 devices between isolator bases(see DF-52389). Line Information: Intelligent Bases"if using a different base. I Fixed-temperature setpoints 135°F (57°C) for the H355(A) ACCESSORIES and H355R(A); 190°F(88°C)for the H355HT(A). F110: Retrofit flange to convert B210LP(A) to match the Rate-of-rise detection:responds to greater than 15°F(8.3°C) B350LP(A) profile, or to convert older high-profile bases to per minute. low-profile. I F110BP:Bulk pack of F110;package contains 15. Listings and Approvals F210:Replacement flange for B210LP(A)base. Listings and approvals below apply to the H355(A) Series RA100Z(A): Remote LED annunciator.3—32 VDC.Mounts to detectors. In some cases, certain modules may not be listed a U.S. single-gang electrical box. For use with B501(A) and by certain approval agencies, or listing may be in process. B210LP(A)bases only. Consult factory for latest listing status. SMB600:Surface mounting kit • UL Listed:S2517. M02-04-00:Test magnet. I • ULC Listed(models H355A, H355RA,H355HTA). M02-09-00:Test magnet with telescoping handle. • CSFM approved:7270-0075:0195. FM approved. XR2B: Detector removal tool. Allows installation and/or • removal of detector heads from bases in high ceiling applica- tions. Product Line Information XP-4: Extension pole for XR2B. Comes in three 5-foot(1.524 NOTE:"A"suffix indicates ULC Listed model. m)sections. H355:Intelligent thermal sensor;135°F(57°C);B210LP base T55-127-010:Detector removal tool without pole. included. H355A: Same as H355 but with ULC Listing; B210LPA base included. I H355R:Same as H355 with rate-of-rise feature;B210LP base included. H355RA: Same as H355R but with ULC Listing; B210LPA I base included. H355HT: Intelligent fixed high-temperature thermal detector; 190° F(88°C); B210LP base included. 1 H355HTA: Same as H355HT but with ULC Listing; B210LPA base included. Fire•Lite®Alarms is a registered trademark of Honeywell International Inc. 1 ©2013 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. - This document is not intended to be used for installation purposes. :.:.:�� I ISO9001 We try to keep our product information up-to-date and accurate. G E R T I F I E O We cannot cover all specific applications or anticipate all requirements. I 6ICINEIMM a MNIIMM MIi All specifications are subject to change without notice. �. , QUALITY SYSTEMS Made in the U.S.A. For more information,contact Fire•Lite Alarms.Phone:(800)627-3473,FAX:(877)699-4105. www.firelite.com Page 2 of 2—DF-52385:D•5/17/2013 1 IDF-60430:C2•E-650 D355PL(A)/DNRW InnovairFlex ��.L�-1-e�ALal"1'Y1S I Intelligent Non-Relay Photoelectric 8 Duct Smoke Detector by H o n eywe l l I - Intelligent Addressable Devices General I . The Fire•Lite InnovairFlex® D355PL(A) intelligent non-relay photoelectric duct smoke detector and DNRW watertight non- relay photoelectric duct smoke detector feature a pivoting housing that fits both square and rectangular footprints capa- I ble of mounting to a round or rectangular duct DNRW duct smoke detector, with its NEMA-4 rating, is listed as a watertight, UV resistant enclosure providing protection ,p"+' against falling dirt, rain, and windblown dust, splashing and I hose directed water, allowing operators to use the detector in the most extreme environments. These units sense smoke in the most challenging conditions, operating in airflow speeds of 100 to 4,000 feet per minute(0.5 I to 20.32 m/s),temperatures of-4°F to 158°F(-20°C to 70°C), and a humidity range of 0 to 95 percent(non-condensing.) An improved cover design isolates the sensor head, which Specifications I allows for ease of maintenance. A cover tamper feature indi- cates a trouble signal for a removed or improperly installed Width,2.5 in(6.6 cm)Depth. sensor cover.The Fire•Lite InnovairFlex housing provides a 3/ 4-inch conduit knockout and ample space to facilitate easy wir- Size:(Square)7.75 in(19.7 cm)Length;9 in(22.9 cm)Width; ing and mounting of a relay module. 2.5 in(6.35 cm)Depth. The Fire•Lite InnovairFlex duct smoke detector can be custom- Weight: 1.6 lb(0.73 kg). ized to meet local codes and specifications without additional Operating Temperature Range: -4°F to 158°F (-20°C to wiring.The new InnovairFlex product line is compatible with all 70°C). I previous Innovair models,including remote test accessories. Storage Temperature Range: -22°F to 158°F (-30°C to 70°C). Features i Operating Humidity Range: 0% to 95% relative humidity • Photoelectric,integrated low-flow technology. (non-condensing). I • Air velocity rating from 100 ft/min to 4,000 ft/min(0.5 m/s to 20.32 m/s). Air Duct Velocity: 100 to 4,000 ft/min(0.5 to 20.32 m/s). • Versatile mounting options: square or rectangular configu- Accessories I ration. • Broad ranges for operating temperature (-4°F to 158°F, - Fire•Lite provides system flexibility with a variety of accesso- 20°C to 70°C)and humidity(0%to 95%non-condensing). ries, including two remote test stations and different means of visible and audible system annunciation. As with our duct • Patented sampling tube installs from front or back of the smoke detectors,all duct smoke detectors accessories are UL I detector with no tools required. listed. • Cover tamper signal. D355PLs and DNRWs with a date code of 0013 or higher do • Increased wiring space with a newly added 3/4" conduit not require external 24VDC for remote test applications when I • knockout. used with a remote-test-capable detector. Available space within housing to accommodate mounting ACCESSORY CURRENT LOADS AT 24 VDC of a relay module. • Easily accessible code wheels on sensor head (sold sepa Device Standby Alarm I rately). • Clear cover for convenient visual inspection. RA100Z OmA 12 mA Max • Remote testing capability. RTS151/ • Requires com line power only. RTS151 KEY OmA 12mA Max I • Accommodates the installation of an addressable relay module, sold separately, (CRF-300)for applications requir- ing aForm-C relay. Agency Listings and Approvals Consult product manual for lists of compatible UL-Listed devices. In some cases,certain modules may not be listed by certain approval agencies, or listing may be in process. Con- - sult factory for latest listing status. I • UL:51059. • ULC:51059 iDF-60430:C2•12/18/2012—Page 1 of 2 • CSFM: 3242-1653:0209. • FM approved. , Product Line Information D355PL: Intelligent non-relay photoelectric low flow smoke detector housing. Includes SD355R Detector. DNRW: Watertight intelligent non-relay photoelectric low flow duct smoke detector housing.Does not include detector head. SD355R(A): Remote test capable addressable low-profile photoelectric smoke detector. SD355(A):Addressable low-profile photoelectric smoke detec- tor. DCOIL: Remote test coil. Required for older DNR(W) duct detector housing. DST1:Metal sampling tube duct width up to 1 ft(0.3m). DST1.5: Metal sampling tube duct widths up to 1 ft to 2 ft(0.3 to 0.6 m). DST3:Metal sampling tube duct widths up to 2 ft to 4 ft(0.6 to 1.2 m). DST5:Metal sampling tube duct widths up to 4 ft to 8 ft(1.2 to 2.4 m). DST10:Metal sampling tube duct widths up to 8 ft to 12 ft(2.4 to 3.7 m). DH4000E-1:Weatherproof enclosure. ETX: Metal exhaust tube duct,width 1 ft(0.3 m). M02-04-00:Test magnet. I P48-21-00: End cap for metal sampling tubes. RA100Z: Remote annunciator alarm LED. RTS151: Remote test station. RTS151 KEY: Remote test station with key lock. • Important Note • DNRW duct detector housings with a date code of 0013 or higher do not require a DCOIL or auxiliary 24 VDC for remote test applications when used with a remote test capable detector. • DNRW duct detector housings with a date code of 0012 or earlier require a DCOIL and auxiliary 24 VDC power for remote test applications. I Fire•Lite®Alarms is a registered trademark of Honeywell International Inc. ©2012 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. • ISO 9001 We try to keep our product information up-to-date and accurate. :::::: CERTIFIED. We cannot cover all specific applications or anticipate all requirements. E81/1®I18 AMMUML1Mllf All specifications are subject to change without notice. IUAIITT SYSTEMS Made in the U.S.A. For more information,contact Fire•Lite Alarms.Phone:(800)627-3473,FAX:(877)699-4105. www.firelite.com Page 2 of 2—DF-60430:C2•12/18/2012 IDF-52121:C•E-325 MMF-300(A) Series, FlI'e•LITt�•ALI'Y1S I MDF-300(A) 8 Addressable Monitor Modules by Honeywell I . Addressable Devices General I - Four different monitor modules are available for Fire•Lite's intelligent control panels to suit a variety of applications. Moni- tor modules are used to supervise a circuit of dry-contact input , , 1110 devices,such as conventional heat detectors and pull stations, ' or monitor and power a circuit of two wire smoke detectors -- (MMF-302(A)). '„,,,, ......W. ."Q."....••.R MMF-300(A)is a standard-sized module(typically mounts to a •�(-11 4" [10.16 cm] square box) that supervises either a Style D I (Class A) or Style B (Class B) circuit of drycontact input •devices. n-•,14 ••"' Mn ....•1•) •• •,•) ••� una mamma MMF-301(A)is a miniature monitor module a mere 1.3"(3.302 M"" cm)H x 2.75"(6.985 cm)W x 0.5"(1.270 cm)D used to super- •' M (�j� ' vise a Style B(Class B)circuit of dry-contact input devices. Its �!J compact design allows the MMF 301(A) to be mounted in a single-gang box behind the device it monitors. MMF-302(A) is a standard sized module used to monitor and , , I supervise compatible two-wire, 24 volt, smoke detectors on a Style D(Class A) or Style B(Class B)circuit. ai MDF-300(A)is a standard-sized dual monitor module used to MMF-300(A)(Type H) I monitor and supervise two independent two-wire Style B (Class B) dry-contact initiating device circuits (IDCs) at two may be wired as an NFPA Style B(Class B)or Style D(Class separate,consecutive addresses in intelligent,two-wire systems. A) Initiating Device Circuit. A 47K ohm End-of-Line Resistor • LiteSpeedTM is a communication protocol developed by (provided) terminates the Style B circuit. No resistor is I Fire•Lite Engineering that greatly enhances the speed of corn- required for supervision of the Style D circuit. munication between analog intelligent devices. Intelligent MMF-300(A) OPERATION devices communicate in a grouped fashion. If one of the devices within the group has new information,the panel CPU Each MMF-300(A) uses one of the available module I stops the group poll and concentrates on single points. The addresses on an SLC loop. It responds to regular polls from net effect is response speed greater than five times that of the control panel and reports its type and the status(open/nor- other designs.designs. maVshort)of its Initiating Device Circuit(IDC).A flashing LED indicates that the module is in communication with the control I MMF-300(A) Monitor Module panel. The LED latches steady on alarm (subject to current limitations on the loop). • Built-in type identification automatically identifies this device as a monitor module to the control panel. MMF-300(A) SPECIFICATIONS I • Powered directly by two-wire SLC loop.No additional power Nominal operating voltage: 15 to 32 VDC. required. Maximum current draw:5.0 mA(LED on). • High noise(EMF/RFI)immunity. Average operating current: 350 pA (LED flashing), 1 corn- • SEMS screws with clamping plates for ease of wiring. munication every 5 seconds,47k EOL. I • Direct-dial entry of address: 01 —159 on MS-9600 series Maximum IDC wiring resistance:40 ohms. panels,01 —99 on other compatible systems. LED flashes during normal operation and latches on steady EOL resistance:47K ohms. • to indicate alarm. Temperature range:32°F to 120°F(0°C to 49°C). I The MMF-300(A) Monitor Module is intended for use in intelli- Humidity range: 10%to 93%noncondensing. gent, two-wire systems, where the individual address of each Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x module is selected using the built-in rotary switches. It pro- 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x I vides either a two-wire or four-wire fault-tolerant Initiating 2 125'(5.398 cm)deep box. Device Circuit (IDC) for normally-open-contact fire alarm and supervisory devices. The module has a panel-controlled LED indicator. The MMF-300(A) can be used to replace M300(A) I modules in existing systems. MMF-300(A)APPLICATIONS Use to monitor a zone of four-wire smoke detectors, manual ' fire alarm pull stations, waterflow devices, or other normally- open dry-contact alarm activation devices. May also be used to monitor normally-open supervisory devices with special supervisory indication at the control panel. Monitored circuit IDF-52121:C•10/06/2010—Page 1 of 4 I MMF-301(A) Mini Monitor Module Dimensions: 1.3" (3.302 cm) high x 2.75" (6.985 cm) wide x • Built-in type identification automatically identifies this deviceI 0.65"(1.651 cm)deep. as a monitor module to the panel. Wire length:6"(15.24 cm)minimum. • Powered directly by two-wire SLC loop.No additional power required. MMF-302(A) Interface Module • High noise(EMF/RFI)immunity. • Supports compatible two-wire smoke detectors. • Tinned,stripped leads for ease of wiring. • Supervises IDC wiring and connection of external power • Direct-dial entry of address: 01 — 159 on MS-9600 series source. panels,01 —99 on other compatible systems • High noise(EMF/RFI)immunity. 1 • SEMS screws with clamping plates for ease of wiring. 1415 0 1 ADDRESS o 1 • Direct-dial entry of address: 01 — 159 on MS-9600 series C 13 ^, 2 panels,01 —99 on other compatible systems. �� Q//.� 4 LOOP e32, • LED flashes during normal operation. I • LED latches steady to indicate alarm on command from control panel. 10 9 TENSs 5 SONES 6 5 The MMF-302(A)Interface Module is intended for use in intelli- n n n n gent, addressable systems, where the individual address of each module is selected using built-in rotary switches. This module allows intelligent panels to interface and monitor two- wire conventional smoke detectors.It transmits the status(nor- 3Y mal,open,or alarm)of one full zone of conventional detectors 0 Lu I W U back to the control panel. All two-wire detectors being moni- Lu 3 03 tored must be UL compatible with the module. The MMF- 302(A) can be used to replace M302(A) modules in existing systems. MMF-302(A)APPLICATIONS I I I Use the MMF-302(A) to monitor a zone of two-wire smoke I The MMF-301(A) Mini Monitor Module can be installed in a detectors. The monitored circuit may be wired as an NFPA single-gang junction directly behind the monitored unit. Its Style B(Class B)or Style D(Class A) Initiating Device Circuit. small size and light weight allow it to be installed without rigid A 3.9 K ohm End-of-Line Resistor (provided) terminates the mounting. The MMF-301(A) is intended for use in intelligent, end of the Style B or D (class B or A) circuit (maximum IDC ii two-wire systems where the individual address of each module loop resistance is 25 ohms). Install ELR across terminals 8 is selected using rotary switches. It provides a two-wire initiat- and 9 for Style D application. 11 ing device circuit for normally-open-contact fire alarm devices. The MMF-301(A)can be used to replace M301(A)modules in MMF-302(A)OPERATION existing systems. Each MMF-302(A) uses one of the available module MMF-301(A)APPLICATIONS addresses on an SLC loop. It responds to regular polls from the control panel and reports its type and the status(open/nor- Use to monitor a single device or a zone of four-wire smoke maVshort)of its Initiating Device Circuit(IDC).A flashing LED detectors,manual fire alarm pull stations,waterflow devices,or indicates that the module is in communication with the control other normally-open dry-contact devices. May also be used to panel. The LED latches steady on alarm (subject to current monitor normally-open supervisory devices with special super- limitations on the loop). visory indication at the control panel. Monitored circuit/device is wired as an NFPA Style B(Class B) Initiating Device Circuit. MMF-302(A)SPECIFICATIONS I A 47K ohm End-of-Line Resistor(provided)terminates the cir- Nominal operating voltage: 15 to 32 VDC. cuit. Maximum current draw:5.1 mA(LED on). MMF-301(A)OPERATION Maximum IDC wiring resistance:25 ohms. Each MMF 301(A) uses one of the available module Average operating current: 300 pA, 1 communication and 1 addresses on an SLC loop. It responds to regular polls from LED flash every 5 seconds,3.9k eol. the control panel and reports its type and the status(open/nor- mal/short)of its Initiating Device Circuit(IDC). EOL resistance:3.9K ohms. , MMF-301(A) SPECIFICATIONS External supply voltage (between Terminals T3 and T4): DC voltage: 24 volts power limited. Ripple voltage: 0.1 Vrms Nominal operating voltage: 15 to 32 VDC. maximum.Current:90 mA per module maximum. Average operating current: 350 pA, 1 communication every Temperature range:32°F to 120°F(0°C to 49°C). I 5 seconds, 47k EOL; 600 pA Max. (Communicating, IDC Shorted). Humidity range: 10%to 93%noncondensing. Maximum IDC wiring resistance 40 ohms. Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x Maximum IDC Voltage: 11 Volts. 2.125"(5.398 cm)deep box. I Maximum IDC Current:400 pA. EOL resistance:47K ohms. Temperature range:32°F to 120°F(0°C to 49°C). 1 Humidity range: 10%to 93%noncondensing. Page 2 of 4—DF-52121:C•10/06/2010 1 I MDF-300(A) Dual Monitor Module Product Line Information I The MDF-300(A) Dual Monitor Module is intended for use in NOTE:"A"suffix indicates ULC-listed model. intelligent, two-wire systems. It provides two independent two- MMF-300(A): Monitor module. wire initiating device circuits(IDCs)at two separate,consecutive addresses. It is capable of monitoring normally open contact fire MMF-301(A): Monitor module, miniature. alarm and supervisory devices.The module has a single panel- MMF-302(A): Monitor module,two-wire detectors. controlled LED. NOTE: The MDF-300(A)provides two Style B(Class B) IDC cir- MDF-300(A): Monitor module, dual, two independent Class B circuits. cults ONLY. Style D(Class A)IDC circuits are NOT supported in I . any application. SMB500:Optional surface mount backbox. MDF-300(A)SPECIFICATIONS NOTE: See installation instructions and refer to the SLC Wiring Manual,PN 51309. Normal operating voltage range: 15 to 32 VDC. I Maximum current draw:6.4 mA(LED on). Architects'/Engineers' Specifications Average operating current:750 NA(LED flashing). Specifications of these devices and all FireLite products are Maximum IDC wiring resistance: 1,500 ohms. available from FireLite. I Maximum IDC Voltage: 11 Volts. Maximum IDC Current:240 pA EOL resistance:47K ohms. I Maximum SLC Wiring resistance:40 Ohms. Temperature range:32°to 120°F(0°to 49°C). Humidity range: 10%to 93%(non-condensing). Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x 2.125"(5.398 cm)deep. MDF-300(A) AUTOMATIC ADDRESSING I The MDF-300(A) automatically assigns itself to two address- able points, starting with the original address. For example, if the MDF-300(A) is set to address "26", then it will automati- cally assign itself to addresses"26"and"27". NOTE: "Ones"addresses on the MDF-300(A)are 0,2, 4, 6, or 8 only. Terminals 6 and 7 use the first address,and terminals 8 and 9 use the second address. I A CAUTION: Avoid duplicating addresses on the system. IInstallation MMF-300(A), MMF-302(A), and MDF-300(A) modules mount directly to a standard 4" (10.16 cm)square,2.125"(5.398 cm) I deep, electrical box. They may also be mounted to the SMB500 surface-mount box. Mounting hardware and installa- tion instructions are provided with each module. All wiring must conform to applicable local codes,ordinances,and regu- Ilations. These modules are intended for power-limited wiring only. The MMF-301(A)module is intended to be wired and mounted without rigid connections inside a standard electrical box. All I wiring must conform to applicable local codes,ordinances,and regulations. Agency Listings and Approvals I In some cases, certain modules may not be listed by certain approval agencies, or listing may be in process. Consult fac- • tory for latest listing status. • UL: S2424 • ULC: S2424 - • FM Approved I • CSFM:7300-0075:0185 • MEA:72-01-E iOF-52121:C•10/06/2010—Page 3 of 4 i . 1 . 1 1 1 1 1 1 1 t 1 1 1 Fire•Lite®and LiteSpeed®are registered trademarks and FireWatchTM is a trademark of Honeywell International Inc. ©2010 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. ISO9001 We try to keep our product information up-to-date and accurate. CER--•F 1 E O We cannot cover all specific applications or anticipate all requirements. MEM M I MNMFir1= All specifications are subject to change without notice. IMALITT SYSTEMS Made in the U.S.A. For more information,contact Fire•Lite Alarms.Phone:(800)627-3473,FAX:(877)699-4105. www.firelite.com Page 4 of 4—DF-52121:C•10/06/2010 1 Idf-60379:A1 •E-400 I CRF-300(A) �ne•uTe•ALarms Relay Module by Honeywell Addressable Devices General I • The CRF-300(A)Addressable Relay Module provides the sys- tem with a dry-contact output for activating a variety of auxil- iary devices, such as fans, door holders, dampers, control equipment, etc. Addressability allows the dry contact to be activated through panel programming,on a select basis. , . No I LiteSpeedTM is a communication protocol developed by0.111.1•11 Fire•Lite Engineering that greatly enhances the speed of corn- ' i munication between analog intelligent devices. Intelligent .ate., �,,. devices communicate in a grouped fashion. If one of the devices within the group has new information, the panel CPU ilt ""'_ ""° " "' stops the group poll and concentrates on single points. The ••••_ mo « net effect is response speed greater than five times that of other designs. r. SO 1 Features • Built-in type identification automatically identifies these , , devices to the control panel. • Internal circuitry and relay powered directly by two-wire SLC loop. I • Integral LED "blinks" green each time a communication is CRF-300(A) received from the control panel and turns on in steady red when activated. - • High noise immunity(EMF/RFI). I • Wide viewing angle of LED. • SEMS screws with clamping plates for wiring ease. Specifications • Direct-dial entry of address:01-159 for MS-9600(A)series Normal operating voltage: 15 to 32 VDC. Ipanels,01 —99 on MS-92000DLS(A)and MS-905OUD(A). Maximum SLC current draw: 6.5 mA(LED on). Applications Average operating current: 230 pA direct poll (CLIP mode), 255 pA group poll(LiteSpeed mode)with LED flashing. The CRF-300(A)may be programmed to operate dry contacts EOL resistance: not used. I for door holders,Air Handling Unit shutdown,etc.,and to reset four-wire smoke detector power. Temperature range: 32°F to 120°F(0°C to 49°C). Humidity range: 10%to 93%non-condensing. I Construction Dimensions: 4.5" (11.43 cm) high x 4" (10.16 cm) wide x • The face plate is made of off-white heat-resistant plastic. 1.25" (3.175 cm) deep. Mounts to a 4" (10.16 cm) square x • Controls include two rotary switches for direct-dial entry of 2.125'(5.398 mm)deep box. address setting. • The CRF-300(A)is configured for a single Class B(Style Y) Relay Contact Ratings or Class A(Style Z)Notification Appliance Circuit. Maximum Current • The CRF-300(A) provides two Form-C dry contacts that Load Description Application Voltage Rating I switch together. Resistive Non-Coded 30 VDC 3.0 A Operation Resistive Coded 30 VDC 2.0 A Each CRF-300(A)uses one of the addresses on a SLC loop.It Resistive Non-Coded 110 VDC 0.9 A I responds to regular polls from the control panel and reports its Resistive Non-Coded 125 VAC 0.9 A type and status, including the open/normal/short status of its • Notification Appliance Circuit(NAC).The LED blinks with each Inductive(UR=5ms) Coded 30 VDC 0.5 A • poll received.On command,it activates its internal relay. Inductive(UR=2ms) Coded 30 VDC 1.0 A INOTE:Open/short supervision is suspended with the CRF-300. Inductive(PF=0.35) Non-Coded 125 VAC 0.5 A Rotary switches set a unique address for each module. The address may be set before or after mounting. The built-in I TYPE CODE(not settable)will identify the module to the con- trol panel,so as to differentiate between a control module and a relay module. Idf-60379:A1•08/04/09—Page 1 of 2 • Agency Listings and Approvals In some cases, certain modules may not be listed by certain I approval agencies, or listing may be in process. Consult fac- tory for latest listing status. • UL:S2424 • ULC:S2424 • FM approved • CSFM:7300-0075:185 • MEA:72-01-E - Product Line Information CRF-300(A): Intelligent addressable relay module. I :Intelligent addressable relay module,ULC listed model. SMB500:Optional surface-mount backbox. NOTE: For installation instructions, see document 156-1190-005 and refer to the SLC Wiring Manual,document 51309. I i 1 1 1 1 1 I 1 LiteSpeed""is a trademark and Fire•Lite©Alarms is a registered trademark of Honeywell International Inc. ©2009 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. :.:.;�� 'SO 9001 We try to keep our product information up-to-date and accurate. - C E R T I F I E U We cannot cover all specific applications or anticipate all requirements. II IIIMI MIME All specifications are subject to change without notice. QUALITY SYSTEMS Made in the U.S.A. For more information,contact Fire•Lite Alarms.Phone:(800)627-3473,FAX:(877)699-4105. www.firelite.com Page 2 of 2—df-60379:A1•08/04/09111 1 DF-52013:D•E-1 00 I BG-12LX Are•LITe`AL ms Addressable Manual Pull Station by Honeywell I ' Addressable Devices General I • The Fire•Lite BG-12LX is a state-of-the-art, dual-action (i.e., requires two motions to activate the station) pull station that includes an addressable interface (mounted inside) for Fire•Lite's addressable fire alarm control panels (FACPs) FIRE I Because the BG-12LX is addressable, the control panel can display the exact location of the activated manual station.This leads fire personnel quickly to the location of the alarm. I Features IPULL PUSH IN I • Maintenance personnel can open station for inspection and P U L L DOWN address setting without causing an alarm condition. I • Built-in bicolor LED, which is visible through the handle of the station,flashes in normal operation and latches steady red when in alarm. • Handle latches in down position and the word"ACTIVATED" I appears to clearly indicate the station has been operated. • Captive screw terminals wire-ready for easy connection to F 11 c ii-c'al 21111S 6 SLC loop(accepts up to 12 AWG/3.25 mm2 wire). I, i'c rE:y;,e n • I • Can be surface mounted (with SB-10 or SB-I/O) or semi- flush mounted. Semi-flush mount to a standard single- g gang,double-gang,or 4"(10.16 cm)square electrical box. s • Smooth dual-action design. a I - • Meets ADAAG controls and operating mechanisms guide- LL lines (Section 4.1.3[13]); meets ADA requirement for 5 lb. maximum activation force. - • Highly visible. usually needed for semi-flush mounting with 4" (10.16 cm) or • Attractive shape and textured finish. double-gang boxes(not with single-gang boxes). • Key reset. • Includes Braille text on station handle. Operation I . Pushing in,then pulling down on the handle causes it to latch Optional trim ring(BG12TR). in the down/activated position. Once latched,the word"ACTI- VATED" (in bright yellow) appears at the top of the handle, Boxes. while a portion of the handle protrudes from the bottom of the station.To reset the station, simply unlock the station with the I Construction key and pull the door open.This action resets the handle;clos- Shell, door, and handle are molded of durable polycarbonate clos- ing the door automatically resets the switch. material with a textured finish. Each manual station, on command from the control panel, sends data to the panel representing the state of the manual I Specifications switch.Two rotary decimal switches allow address settings (1 —159 with Breakaway Tab removed for MS-9600 Series, 1 — • Shipping Weight:9.6 oz.(272.15 g) 99 and MS-92000DLS, 1 —50 for MS-9050UD). • Normal operating voltage:24 VDC. • Maximum SLC loop voltage:28.0 VDC. Architectural/Engineering • Maximum SLC standby current:375 NA. Specifications • Maximum SLC alarm current:5 mA. Manual Fire Alarm Stations shall be non-coded, with a key- I • Temperature Range:32°F to 120°F(0°C to 49°C) operated reset lock in order that they may be tested, and so • Relative Humidity: 10%to 93%(noncondensing) designed that after actual Emergency Operation, they cannot be restored to normal except by use of a key.An operated sta- • • For use Indoors In a dry location tion shall automatically condition itself so as to be visually I detected as activated. Manual stations shall be constructed of Installation red-colored polycarbonate material with clearly visible operat- The BG-12LX will mount semi-flush into a single-gang,double- ing instructions provided on the cover. The word FIRE shall gang,or standard 4"(10.16 cm)square electrical outlet box,or appear on the front of the stations in white letters, 1.00 inches I will surface mount to the model SB-10 or SB-I/O surface back- (2.54 cm) or larger. Stations shall be suitable for surface box. If the BG-12LX is being semi-flush mounted, then the mounting on matching backbox SB-10 or SB-I/O;or semi-flush optional trim ring (BG12TR) may be used. The BG12TR is mounting on a standard single-gang, double-gang, or 4"(10.16 cm) square electrical box, and shall be installed IDF-52013:D•4/13/2012—Page 1 of 2 within the limits defined by the Americans with Disabilities Act (ADA) or per national/local requirements. Manual Stations 1111 shall be Underwriters Laboratories listed. Manual stations shall connect with two wires to one of the con- trol panel SLC loops. The manual station shall, on command from the control panel,send data to the panel representing the state of the manual switch. Manual stations shall provide address setting by use of rotary decimal switches. Product Line Information - BG-12LX: Dual-action addressable pull station. Includes key locking feature. (Listed for Canadian and non-Canadian appli- cations.) SB-10:Surface backbox;metal. SB-UO:Surface backbox; plastic. BG12TR:Optional trim ring. 17003:Keys,set of two. Agency Listings and Approvals In some cases, certain modules or applications may not be I listed by certain approval agencies, or listing may be in pro- cess.Consult factory for latest listing status. • UL/ULC Listed: S711 (listed for Canadian and non-Cana- dian applications). • MEA:67-02-E. • CSFM:7150-0075:0184. • FM Approved. Patented: U.S. Patent No. D428,351; 6,380,846; 6,314,772; 6,632,108. I 1 1 I I 1 FireLite®Alarms®is a registered trademark of Honeywell International Inc. 02012 by Honeywell International Inc.All rights reserved.Unauthorized use of this document is strictly prohibited. This document is not intended to be used for installation purposes. 's0 9001 We try to keep our product information up-to-date and accurate. E R.11 E O We cannot cover all specific applications or anticipate all requirements. MIME INi I MNIIMCSIMM All specifications are subject to change without notice. IMALITT SYSTEMS Made in the U.S.A. For more information,contact Fire•Lite Alarms.Phone:(800)627-3473,FAX:(877)699-4105. www.firelite.com Page 2 of 2—DF-52013:D•4/13/2012 . a ... , I SILENTModel 5495 Distributed Power Module I . 44 KNIGHT © In an emergency, by Honeywell you need maximum power I The 5495 Distributed Power Module by Silent Knight is the most powerful and cost-effective power supply available today. It delivers 6 amps of notification appliance circuit power and built-in synchronization for appliances from System Sensor®,Gentex®,AMSECO®, Wheelock and Faraday—what you need to drive power- ' hungry components like ADA notification appliances. The 5495's advanced microprocessor design is years ahead of the competition. Its switch mode power supply design is up to 50% more efficient than competitive linear mode power supplies.And,ADA retrofits are easier and less expensive with the 5495 because it integrates into current systems without the costly investment in new components. IFor the most sophisticated and cost-effective notification power supply available, you need the 5495. Call Silent Knight today for more information at 1-800-328-0103. IModel 5495 to non-essential high-current Distributed Power Module accessories like magnetic door holders I The 5495 is a 6 amp notification power Built-in• synchronization for expander that provides its own AC appliances from System power connection, battery charging Sensor®,Gentex®,AMSECO®, circuit, and backup battery for use with Wheelock and Faraday I fire and security controls such as the Silent Knight Model 5208 Fire Control • Stand alone operation /Communicator.The 5495 is the cost- • Lightweight design adds to ease of effective solution for powering installation and reduces shipping Inotification appliances required by the with Disabilities Act(ADA). Operates with most polarized, UL The 5495 has built-in ANSI cadence Listed notification devices I pattern,which can upgrade older ANSI Cadence pattern output control panels that lack cadence capability. • capability built-in TS IFeatures Connection to Local Fire Control The 5495 may be connected to a local • UL Listed for 6 amps of notification Model 5495 fire control which utilizes Class A or I power Class B type notification circuits Distributed Power Module • Power supply's advanced switch operating between 9 and 32 VDC.The mode design reduces damaging control panel's notification circuit is Approvals heat and manages power up to 50% connected to one of the inputs on the • UL Listed I more efficiently than other systems 5495.The control panel's notification • MEA 429-92-E Vol XII • Dip switches allow for easy circuit end-of-line resistor is also • CSFM 7300-0559:123 reconfiguration connected across two terminals on the • I . 24 VDC filtered output voltage 5495,which provides supervision NFPA 72 • Four power-limited notification between the 5495 and the fire control • OSHPD (CA)OSP-0065-10 outputs; 2 Class A or 4 Class B, or 1 panel. Polarized audible and/or visual (see accessories) Class A and 2 Class B notification devices are then connected • Additional continuous auxiliary to the 5495 signal circuits using the output 4.71d)end-of-line resistors provided. Since the 5495 draws very little power ' • 3 amps per output circuit from the control, it is possible to I • 2 inputs; 2 Class B or 2 Class A • Ground fault detector/indicator connect one 5495 to each notification circuit on the control panel and still • Independent trouble relay provide full supervision of the I • AC loss delay option shuts off power notification circuits all the way back to the control panel. - • , •-• Model 5495 1 Distributed Power Module . 1 Model 5495 Block Diagram . i Signal Circuit Output Signal 1 Signal 1 I Input Distributed Signal 2 SiSignal Circuit Output SInnal2 put Module Power4955 Signal 31 (Optional) Signal 4 120 VAC Aux. Power I Trouble Output Local Fire Control (Alternative to notificationI circuit trouble.) Supervision Current: Input I The 5495 supervises a variety of Standby 75 mA voltage range: 9 -32 VDC functions including: Alarm 205 mA Battery charging • • Low AC power Auxiliary capacity: 35.0 AH I • Low battery condition power circuit: 1 Ambient temp.: 32° to 120° F _ • Earth ground fault Notification (0° to 49° C) • Auxiliary output power limit circuits: 4 Mechanical I condition Output Dimensions: 12.25"W x 16" H x • EOL supervision trouble or configuration: 2 Class A(Style Z) 3" D (30.88 cm W power limited condition at an 4 Class B (Style Y) x 40.64 cm H x output (1 Class A& 7.62 D cm) When a trouble condition occurs, 2 Class B) Indicator Lights the 5495 creates a trouble Amps per AC power on : GreenI condition on the host control signal output circuit: 3.0 (6.0 amps circuits to which it is connected. the p p total) Battery trouble: Yellow 5495 still maintains the ability to be Notification Ground fault: Yellow activated by the host control. In circuit output: 20.4 to 27.3 VDCI addition, the 5495 provides a Form @ 3.0 amps each, Aux trouble: Yellow C trouble relay output as an 4.7 Id2 EOL Output troubles (1-4): Yellow alternative to using the notification resistor required Ordering Information I circuit trouble. on each Class B 5495 Distributed Power Module circuit Electrical Specification Accessories: AC input: 120 VAC at 2 amps No. of inputs 2 pInput SK-SCK Seismic Compliance Kit Output: 24 VDC at 6 amps configuration: 2 Class B or 2 Class A 1 SILENT This document is not intended to be used for installation purposes.We try to MADE IN AMERICA KNIGHT keepproduct on pode ae.Wcanno specific applicationsprducinformatior anticipateu -tall- atrequirements.andaccurAlltspeceificationsotcare alI FORM#350395 Rev F subject to change without notice. For more information,contact Silent Knight ©2013 Honeywell International Inc. by Honeywell 12 Clintonville Road, Northford,CT 06472-7161 Phone:(800)328-0103, Fax:(203)484-7118.For Technical Support,please call 800-446-6444. I www.sllentkn ight.com I . ,. . I *, Th, SYSTEM SENSOR •I . ,6 { ... may. :, .... . , - ,s I . Indoor Selectable- _. Output Strobes and ,,, , I Horn Strobes for � � Ceiling .....4,1 ii II Applications ii ` 4*---TP'' ''' ::1.': t 4 d I SpectrAled®Advance audible visible notification products are rich with features guaranteed to cut installation times SPE I FAlert iand maximize profits. A o v A N c E I Features The SpectrAlert Advance series offers the most versatile and I easy-to-use line of horns,strobes,and horn strobes in the industry. • Plug-in design with minimal intrusion into the back box With white and red plastic housings,wall and ceiling mounting • Tamper-resistant construction options,and plain and FIRE-printed devices,SpectrAlert Advance • Automatic selection of 12-or 24-volt operation at 15 and can meet virtually any application requirement. I 15/75 candela Like the entire SpectrAlert Advance product line,ceiling-mount • Field-selectable candela settings on ceiling units: 15, 15/75,30, 75,95, 110, 115, 135, 150, 177,and 185 strobes and horn strobes include a variety of features that increase I their application versatility while simplifying installation.All devices • Horn rated at 88+dBA at 16 volts feature plug-in designs with minimal intrusion into the back box, • Rotary switch for horn tone and three volume selections making installations fast and foolproof while virtually eliminating costly and time-consuming ground faults. • Universal mounting plate for ceiling units • Mounting plate shorting spring checks wiring continuity before To further simplify installation and protect devices from construction device installation damage,SpectrAlert Advance utilizes a universal mounting plate I • Electrically Compatible with legacy SpectrAlert devices with an onboard shorting spring,so installers can test wiring • Compatible with MDL sync module continuity before the device is installed. I • Listed for ceiling or wall mounting Installers can also easily adapt devices to a suit a wide range of application requirements using field-selectable candela settings, automatic selection of 12-or 24-volt operation,and a rotary switch Ifor horn tones with three volume selections. Agency Listings I SIGNALING `0) I 0 ® ATEA Iiiiii approved77112255:11665533 - (indoosr tr LISTED �APPROVEDPP 71257125-1653:1881653186(horn trsobes,obes) 54011(chimes.horn strobes,horns) 3023572 MEA452-05-E chime strobes) S5512(strobes) 7135-1653189(horns.chimes) I SpectrAlert Advance Specifications I Architect/Engineer Specifications General SpectrAlert Advance strobes and horn strobes shall mount to a standard 4 x 4 x 11/2-inch back box,4-inch octagon back box,or double- gang back box.Two-wire products shall also mount to a single-gang 2 x 4 x 17/8-inch back box.A universal mounting plate shall be used for mounting ceiling and wall products.The notification appliance circuit wiring shall terminate at the universal mounting plate.Also,SpectrAlert Advance products,when used with the Sync•Circuitvm Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 9 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 17 and 33 volts. Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full-wave rectified unfiltered power supply.Strobes and horn strobes shall have field-selectable candela settings including 15, 15/75,30,75,95, 110, 115, 135, 150, 177,and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have three audibility options and an option to switch between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.On four-wire products,the strobe shall be powered independently of the sounder.The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync•Circuit model MDL listed to UL 464 and shall be approved for fire protective service.The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three.Also,while operating the strobes,the module shall silence the horns on horn strobe models over a single pair of wires.The module shall mount to a 411/16 x 411/16 x 21/8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power supply. Physical/Electrical Specifications Standard Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR1 Operating Voltage Rangel 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Ceiling-Mount Dimensions(including lens) 6.8"diameter x 2.5"high(173 mm diameter x 64 mm high) Ceiling-Mount Back Box Skirt Dimensions(BBSC-2,BBSCW-2) 7.1"diameter x 2.2"high(180 mm diameter x 57 mm high) Ceiling-Mount Trim Ring Dimensions(sold as a 5 pack)(TRC-HS, 6.9"diameter x 0.35"high(175 mm diameter x 9 mm high) TRCW-HS) Notes: 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.P,S,PC,and SC products will operate at 12 V nominal only for 15 and 15/75 cd. 1 1 1 AVDS00501 , I IUL Current Draw Data UL Max.Strobe Current Draw(mA RMS) 8-17.5 Volts 16-33 Volts Candela DC FWR DC FWR Standard Candela Range 15 123 128 66 71 15/75 142 148 77 81 30 NA NA 94 96 75 NA NA 158 153 95 NA NA 181 176 110 NA NA 202 195 I 115 NA NA 210 205 High 135 NA NA 228 207 Candela Range 150 NA NA 246 220 I 177 NA NA 281 251 185 NA NA 286 258 UL Max.Current Draw(mA RMS),2-Wire Horn Strobe,Standard Candela Range(15-115 cd) I 8-17.5 Volts 16-33 Volts DC Input 15 15/75 15 15/75 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 I Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 I Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 - Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 • Non-Temporal Medium 134 155 85 95 110 166 189 208 216 Non-Temporal Low 132 154 80 90 105 161 184 202 211 UL Max.Current Draw(mA RMS),2-Wire Horn Strobe,High Candela Range(135-185 cd) 16-33 Volts 16-33 Volts I DC Input 135 150 177 185 FWR Input 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non-Temporal High 255 270 303 309 Non-Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 IHorn Strobe Tones and Sound Output Data Horn Strobe Output(dBA) I 8-17.5 16-33 24-Volt Nominal Switch Volts Volts Reverberant Anechoic Position Sound Pattern dB DC FWR DC FWR DC FWR DC FWR 1 Temporal High 78 78 84 84 88 88 99 98 2 Temporal Medium 74 74 80 80 86 86 96 96 3 Temporal Low 71 73 76 76 83 80 94 89 4 Non-Temporal High 82 82 88 88 93 92 100 100 5 Non-Temporal Medium 78 78 85 85 90 90 98 98 6 Non-Temporal Low 75 75 81 81 88 84 96 92 7t Coded High 82 82 88 88 93 92 101 101 I 8t Coded Medium 78 78 85 85 90 90 97 98 9t Coded Low 75 75 81 81 88 85 96 92 tSettings 7,8,and 9 are not available on 2-wire horn strobes. IAVDS00501 I SpectrAlert Advance Dimensions I 7.1" 1.-2.25 1 I 6.8" — Dia. I C omit Dia. / O Q. [ i-j--- -----------......A O f� o Q COoer ) ( o o • I 1 I It b N Cy sI Ceiling-mount horn strobes Ceiling back box skirt I I I -. I I I SpectrAlert Advance Ordering Information Model Description Model Description I Ceiling Horn Strobes Ceiling Strobes PC2R* 2-Wire Horn Strobe,Standard cd,Red SCR Strobe,Standard cd,Red PC2RH 2-Wire Horn Strobe,High cd,Red SCRH Strobe,High cd,Red I PC2W*1 2-Wire Horn Strobe,Standard cd,White SCW* Strobe,Standard cd,White PC2WH* 2-Wire Horn Strobe,High cd,White SCWH Strobe,High cd,White PC4R 4-Wire Horn Strobe,Standard cd,Red Accessories PC4RH 4-Wire Horn Strobe,High cd,Red BBSC-2 Back Box Skirt,Ceiling,RedI PC4W 4-Wire Horn Strobe,Standard cd,White Back Box Skirt,Ceiling,White TRC-HS Trim Ring,Ceiling,Red TRCW- Trim Ring,Ceiling,White 1 HS Notes: *Add"-P"to model number for plain housing(no"FIRE"marking on cover),e.g.,P2R-P. t Add"-SP"to model number for"FUEGO"marking on cover,e.g.,P2R-SP. 1 t"Standard cd"refers to strobes that include 15,15/75,30,75,95,110,and 115 candela settings."High cd"refers to strobes that include 135,150,177,and 185 candela settings. ,� SYSTEM ©2012 System Sensor. 3825 Ohio Avenue•St.Charles,IL 60174 Product specifications subject to change wiUautnotice.Visit systemsensor.com �� SEwSOR" Phone:800-SENSOR2•Fax:630-377-6495 for current product information,including the latest version of this data sheet. AVDS00501•3/12 1 I . ., . I SYSTEM , V SENSOR` Fz.---,.." F I Indoor Selectable- R =,, Output Horns, IIII 1 Strobes, and , .:-."":"^"\,T. 10 Horn Strobes for R Wall Applications 0 Ifit SpectrAlert®Advance audible visible notification products SPECTRAIert iare rich with features guaranteed to cut installation times __ o v i N c E and maximize profits. I Features The SpectrAlert Advance series offers the most versatile and • Plug-in design with minimal intrusion into the back box easy-to-use line of horns,strobes,and horn strobes in the industry. With white and red plastic housings,wall and ceiling mounting • Tamper-resistant construction options,and plain and FIRE-printed devices,SpectrAlert Advance • Automatic selection of 12-or 24-volt operation at can meet virtually any application requirement. 15 and 15/75 candela • Field selectable candela settings on wall units: 15, 15/75, Like the entire SpectrAlert Advance product line,wall-mount horns, 30,75,95, 110, 115, 135, 150, 177,and 185 strobes,and horn strobes include a variety of features that increase their application versatility while simplifying installation.All devices • Horn rated at 88+dBA at 16 volts feature plug-in designs with minimal intrusion into the back box, • Rotary switch for horn tone and three volume selections making installations fast and foolproof while virtually eliminating I • Universal mounting plate for wall units costly and time-consuming ground faults. • Mounting plate shorting spring checks wiring continuity before To further simplify installation and protect devices from construction device installation damage,SpectrAlert Advance utilizes a universal mounting plate i • Electrically Compatible with legacy SpectrAlert devices with an onboard shorting spring,so installers can test wiring • Compatible with MDL3 sync module continuity before the device is installed. I • Listed for ceiling or wall mounting Installers can also easily adapt devices to a suit a wide range of application requirements using field-selectable candela settings, automatic selection of 12-or 24-volt operation,and a rotary switch Ifor horn tones with three volume selections. IAgency Listings co; MALMO I01 ® MEA roved (no LISTED approved 7125-16531887125-1653.186 i (horndostrobes,rstrobes) 54011(chimes,horn strobes,horns) 3023572 MEA452-05-E chime strobes) S5512(strobes) 7135-1653.189(horns,chimes) SpectrAlert Advance Specifications Architect/Engineer Specifications General 1 SpectrAlert Advance horns,strobes,and horn strobes shall mount to a standard 4 x 4 x 11/2-inch back box,4-inch octagon back box,or double-gang back box.Two-wire products shall also mount to a single-gang 2 x 4 x 17/8-inch back box.A universal mounting plate shall be used for mounting ceiling and wall products.The notification appliance circuit wiring shall terminate at the universal mounting plate. Also,SpectrAlert Advance products,when used with the Sync•Circuit'"Module accessory,shall be powered from a non-coded notification appliance circuit output and shall operate on a nominal 12 or 24 volts.When used with the Sync•Circuit Module, 12-volt-rated notification appliance circuit outputs shall operate between 8.5 and 17.5 volts;24-volt-rated notification appliance circuit outputs shall operate between 16.5 and 33 volts.Indoor SpectrAlert Advance products shall operate between 32 and 120 degrees Fahrenheit from a regulated DC or full- wave rectified unfiltered power supply.Strobes and horn strobes shall have field-selectable candela settings including 15,15/75,30,75,95, 110, 115, 135, 150, 177,and 185. Strobe The strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and shall be approved for fire protective service. The strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system. Horn Strobe Combination The horn strobe shall be a System Sensor SpectrAlert Advance Model listed to UL 1971 and UL 464 and shall be approved for fire protective service.The horn strobe shall be wired as a primary-signaling notification appliance and comply with the Americans with Disabilities Act requirements for visible signaling appliances,flashing at 1 Hz over the strobe's entire operating voltage range.The strobe light shall consist of a xenon flash tube and associated lens/reflector system.The horn shall have three audibility options and an option to switch 111 between a temporal three pattern and a non-temporal(continuous)pattern.These options are set by a multiple position switch.On four-wire products,the strobe shall be powered independently of the sounder.The horn on horn strobe models shall operate on a coded or non-coded power supply. Synchronization Module The module shall be a System Sensor Sync•Circuit model MDL3 listed to UL 464 and shall be approved for fire protective service.The module shall synchronize SpectrAlert strobes at 1 Hz and horns at temporal three.Also,while operating the strobes,the module shall silence the horns on horn strobe models over a single pair of wires.The module shall mount to a 411/16 x 411/16 x 21/8-inch back box.The module shall also control two Style Y(class B)circuits or one Style Z(class A)circuit.The module shall synchronize multiple zones.Daisy chaining two or more synchronization modules together will synchronize all the zones they control.The module shall not operate on a coded power supply. Physical/Electrical Specifications Standard Operating Temperature 32°F to 120°F(0°C to 49°C) Humidity Range 10 to 93%non-condensing Strobe Flash Rate 1 flash per second Nominal Voltage Regulated 12 DC/FWR or regulated 24 DC/FWR' Operating Voltage Rangel 8 to 17.5 V(12 V nominal)or 16 to 33 V(24 V nominal) Operating Voltage Range MDL3 Sync Module 8.5 to 17.5 V(12 V nominal)or 16.5 to 33 V(24 V nominal) Input Terminal Wire Gauge 12 to 18 AWG Wall-Mount Dimensions(including lens) 5.6"L x 4.7-W x 2.5"D(142 mm L x 119 mm W x 64 mm D) Horn Dimensions 5.6"L x 4.7"W x 1.3"D(142 mm L x 119 mm W x 33 mm D) Wall-Mount Trim Ring Dimensions(sold as a 5 pack)(TR-HS) 5.7"L x 4.8"W x 0.35"D(145 mm L x 122 mm W x 9 mm D) Notes: 1.Full Wave Rectified(FWR)voltage is a non-regulated,time-varying power source that is used on some power supply and panel outputs. 2.P,S,PC,and SC products will operate at 12 V nominal only for 15 and 15/75 cd. I 1 I 1 T SYSTEM I .. �_ SENSOR® at '1104 I ' Outdoor Selectable- Output Horns, "' Strobes, and 1 Horn Strobes for Wall Applications I SPECTFAlert SpectrAlert®Advance outdoor audible visible products g► o v .ta N c E Iare rich with features that cut installation times and maximize profits. I Features SpectrAlert Advance offers the broadest line of outdoor horns, I - • Weatherproof per NEMA 4X, IP56 strobes,and horn strobes in the industry.With white or red plastic housings,wall or ceiling mounting options,and plain or FIRE-printed • Listed to UL 1638(strobe)and UL 464(horn) devices,SpectrAlert Advance can meet virtually any application • • Compatible with System Sensor synchronization protocol and requirement,including indoor,outdoor,wet,and dry applications in legacy SpectrAlert products temperatures from-40°F to 151°F. • Field-selectable candela settings: 15, 15/75,30,75,95, 110, 115, 135, 150, 177,and 185 Like the entire SpectrAlert Advance line,outdoor horns,strobes, and horn strobes for wall applications include a variety of features • Automatic selection of 12-or 24-volt operation at 15 and that increase application flexibility and simplify installation.First, 15/75 candela field-selectable settings, including candela,automatic selection of I • Rotary switch for horn tone and three volume selections 12-or 24 volt operation,horn tones,and three volume options enable • Horn rated at 88+dBA at 16 volts installers to easily adapt devices to meet requirements. • Rated from-40°F to 151°F Next,SpectrAlert Advance devices use a universal mounting plate I • Universal mounting plate with an onboard shorting spring that for both wall and ceiling applications.This mounting plate includes tests wiring continuity before devices are installed an onboard shorting spring that ensures wiring continuity before • Plug-in design with minimal intrusion into the back box devices are installed,so installers can verify proper wiring without mounting the devices and exposing them to potential construction I • Tamper-resistant construction damage.Once the plates are mounted,all SpectrAlert Advance • Listed for ceiling or wall mounting devices utilize a plug-in design with a single captured screw to Ispeed installation and virtually eliminate costly ground faults. Outdoor devices ship with weatherproof plastic back boxes(metal back boxes are available separately)that accommodate in-and- I Agency Listings out wiring for daisy chaining devices.Plastic back boxes feature removable side flanges and improved resistance to saltwater SIGNALING corrosion.Knock-outs located on the back eliminate the need to drill o)( holes for screw-in mounting.Plastic and metal weatherproof back I 0 �C A t y t boxes come with 3/4-inch top and bottom conduit entries and 3/4-inch LISTED ® L!1 7305-1653 187(outdoorhornststrobes) approved 7125.1653188(horn strobes. knock-outs at the back.A screw-in NPT plug with an 0-ring gasket S4011(ch Ines,horn strobes.horns) APPROVED chime strobes) IS3593(outdoor and alert strobes) 3023572 MEA452-05-E 7135-1653189(horns,chimes) for a watertight seal is included with each back box. I L rrent Draw I U Cu Data UL Max.Strobe Current Draw(mA RMS) UL Max.Horn Current Draw(mA RMS) 8-17.5 Volts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC FWR DC FWR Sound Pattern dB DC FWR DC FWR Standard 15 123 128 66 71 Temporal High 57 55 69 75 Candela 15/75 142 148 77 81 Temporal Medium 44 49 58 69 Range 30 NA NA 94 96 Temporal Low 38 44 44 48 I . 75 NA NA 158 153 Non-Temporal High 57 56 69 75 95 NA NA 181 176 Non-Temporal Medium 42 50 60 69 I 110 NA NA 202 195 Non-Temporal Low 41 44 50 50 115 NA NA 210 205 Coded High 57 55 69 75 High 135 NA NA 228 207 Coded Medium 44 51 56 69 Candela 150 NA NA 246 220 Coded Low 40 46 52 50 Range 177 NA NA 281 251 185 NA NA 286 258 UL Max.Current Draw(mA RMS).2-Wire Horn Strobe.Standard Candela Range(15-115 cd) 1 8-17.5 Volts 16-33 Volts DC Input 15 15!75 15 15/75 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 I Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 Non-Temporal Low 131 144 68 79 96 156 182 201 210 I FWR Input Temporal High 136 155 88 97 112 168 190 210 218 - Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 - Non-Temporal Medium 134 155 85 95 110 166 189 208 216 I Non-Temporal Low 132 154 80 90 105 161 184 202 211 UL Max.Current Draw(mA RMS).2-Wire Horn Strobe.High Candela Range(135-185 cd) 16-33 Volts 16-33 Volts I DC Input 135 150 177 185 FWR Input 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 a Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 I Non-Temporal High 255 270 303 309 Non Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 ICandela Derating Horn Tones and Sound Output Data For K series products used at low temperatures,listed Horn and Horn Strobe Output(dBA) candela ratings must be reduced in accordance with 8-1Z5 16-33 24-Volt Nominal I this table. Strobe Output(cd) Switch Sound Volts Volts Reverberant Anechoic Position Pattern dB DC FWR DC FWR DC FWR DC FWR Listed Candela Candela rating at-40°F 1 Temporal High 78 78 84 84 88 88 99 98 15 2 Temporal Medium 74 74 80 80 86 86 96 96 I 15/75 Do not use below 32°F 3 Temporal Low 71 73 76 76 83 80 94 89 30 4 Non- High • 75 44 Temporal 82 82 88 88 93 92 100 100 95 70 5 Non- Medium 110 110 Temporal 78 78 85 85 90 90 98 98 • 115 115 6 Non- Low 135 135 Temporal 75 75 81 81 88 84 96 92 I 150 150 7t Coded High 82 82 88 88 93 92 101 101 177 177 8t Coded Medium 78 78 85 85 90 90 97 98 185 185 9t Coded Low 75 75 81 81 88 85 96 92 ItSettings 7,8,and 9 are not available on 2-wire horn strobe. Aws01201 I SpectrAlert Advance Diagrams I lo--4.7" ► 2.9r. ® lj57■ \4 ; : �� I ■ / 5.6" "4 /pi II) I j II.." -_, -_____L___ ke:llkI. 11k, o i-I ca IWall-Mount HornStrobes <� �--- Wall Plastic Weatherproof Back Box �� 1 ' 1.------::---- --- , ips u�� 1 i) I WI Wall-Mount Horn Strobe with Plastic Weatherproof Back Box I SpectrAlert Advance Ordering Information • Model Description I Wall Horn Strobes P2RK*t 2-Wire Horn Strobe,Standard cd,Red,Outdoor(includes plastic weatherproof back box) P2RHK*t 2-Wire Horn Strobe,High cd,Red,Outdoor(includes plastic weatherproof back box) P2WK*t 2-Wire Horn Strobe,Standard cd,White,Outdoor(includes plastic weatherproof back box) P2WHK*t 2-Wire Horn Strobe,High cd,White,Outdoor(includes plastic weatherproof back box) P4RKt 4-Wire Horn Strobe,Standard cd,Red,Outdoor(includes plastic weatherproof back box) P4WK 4-Wire Horn Strobe,Standard cd,White,Outdoor(includes plastic weatherproof back box) P2RHK-120 2-Wire Horn Strobe,High cd,Red,Outdoor, 120 V(includes plastic weatherproof back box) Wall Strobes SRK*t Strobe,Standard cd,Red,Outdoor(includes plastic weatherproof back box) SRHK*t Strobe,High cd,Red,Outdoor(includes plastic weatherproof back box) SWK*t Strobe,Standard cd,White,Outdoor(includes plastic weatherproof back box) SWHK*t Strobe,High cd,White,Outdoor(includes plastic weatherproof back box) Horns HRKt Horn,Red,Outdoor(includes plastic weatherproof back box) Accessories SA-WBB Red,Metal Weatherproof Back Box SA-WBBW White,Metal Weatherproof Back Box Notes: ` *Add"-P"to model number for plain housing(no"FIRE"marking on cover),e.g.,P2RK-P. t Add"-R"to model number for weatherproof replacement device(no back box included),only for use with weatherproof outdoor flush mounting plate,WTP and WTPW. "Standard cd"refers to strobes that include 15,15/75,30,75,95,110,and 115 candela settings."High cd"refers to strobes that include 135,150,177,and 185 candela settings.When replacing standard outdoor units both the device and back box must be replaced. ` m SYSTEM ®21)12 System Sensor. 3825 Ohio Avenue•St.Charles, IL 60174 Product speciications subject to change without notice.Visit systemsensor.com �$ SENSOR Phone:800-SENSOR2•Fax:630-377-6495 for current product information,including the latest version of this data sheet. AVDS01201•3/12 . I TUL Current Draw Data UL Max.Strobe Current Draw(mA RMS) UL Max.Horn Current Draw(mA RMS) 8-17.5 Volts 16-33 Volts 8-17.5 Volts 16-33 Volts Candela DC FWR DC FWR Sound Pattern dB DC FWR DC FWR Standard 15 123 128 66 71 Temporal High 57 55 69 75 Candela 15/75 142 148 77 81 Temporal Medium 44 49 58 69 I . Range 30 NA NA 94 96 Temporal Low 38 44 44 48 75 NA NA 158 153 Non-temporal High 57 56 69 75 95 NA NA 181 176 Non-temporal Medium 42 50 60 69 j 110 NA NA 202 195 Non-temporal Low 41 44 50 50 I115 NA NA 210 205 Coded High 57 55 69 75 High 135 NA NA 228 207 Coded Medium 44 51 56 69 Candela 150 NA NA 246 220 Coded Low 40 46 52 50 Range 177 NA NA 281 251 185 NA NA 286 258 UL Max.Current Draw(mA RMS).2-Wire Horn Strobe,Standard Candela Range(15-115 cd) 8-17.5 Volts 16-33 Volts DC Input 15 15175 15 15/75 30 75 95 110 115 Temporal High 137 147 79 90 107 176 194 212 218 Temporal Medium 132 144 69 80 97 157 182 201 210 Temporal Low 132 143 66 77 93 154 179 198 207 Non-Temporal High 141 152 91 100 116 176 201 221 229 Non-Temporal Medium 133 145 75 85 102 163 187 207 216 I Non-Temporal Low 131 144 68 79 96 156 182 201 210 FWR Input Temporal High 136 155 88 97 112 168 190 210 218 ' Temporal Medium 129 152 78 88 103 160 184 202 206 Temporal Low 129 151 76 86 101 160 184 194 201 Non-Temporal High 142 161 103 112 126 181 203 221 229 Non-Temporal Medium 134 155 85 95 110 166 189 208 216 INon-Temporal Low 132 154 80 90 105 161 184 202 211 UL Max.Current Draw(mA RMS).2-Wire Horn Strobe,High Candela Range(135-185 cd) 16-33 Volts 16-33 Volts DC Input 135 150 177 185 FWR Input 135 150 177 185 Temporal High 245 259 290 297 Temporal High 215 231 258 265 Temporal Medium 235 253 288 297 Temporal Medium 209 224 250 258 Temporal Low 232 251 282 292 Temporal Low 207 221 248 256 Non Temporal High 255 270 303 309 Non Temporal High 233 248 275 281 Non-Temporal Medium 242 259 293 299 Non-Temporal Medium 219 232 262 267 Non-Temporal Low 238 254 291 295 Non-Temporal Low 214 229 256 262 I Horn Tones and Sound Output Data I Horn and Horn Strobe Output(dBA) 8-17.5 16-33 24-Volt Nominal Switch Volts Volts Reverberant Anechoic I Position Sound Pattern dB DC FWR DC FWR DC FWR DC FWR 1 Temporal High 78 78 84 84 88 88 99 98 2 Temporal Medium 75 75 80 80 86 86 96 96 3 Temporal Low 71 71 76 76 83 80 94 89 I 4 Non-Temporal High 82 82 88 88 93 92 100 100 5 Non Temporal Medium 78 78 85 85 90 90 98 98 6 Non-Temporal Low 73 74 81 81 88 84 96 92 71 Coded High 82 82 88 88 93 92 101 101 8t Coded Medium 78 78 85 85 90 90 97 98 91 Coded Low 74 75 81 81 88 85 96 92 Settings 7,8,and 9 are not available on 2-wire horn strobes. I SpectrAlert Advance Dimensions I 1.-4.7" 2.5'=. 1 • 5.6"IIIM1 1.voI■ re 1. Wall-mount horn strobes I I i SpectrAlert Advance Ordering Information Model Description Model Description Wall Horn Strobes Wall Strobes(cont.) I P2R 2-Wire Horn Strobe,Standard cd,Red SRH Strobe,High cd,Red P2R-P 2-Wire Horn Strobe,Standard cd,Red,Plain SRH-P Strobe,High cd,Red,Plain P2R-SP 2-Wire Horn Strobe,Standard cd,Red,"FUEGO" SRH-SP Strobe,High cd,Red,"FUEGO" I P2RH 2-Wire Horn Strobe,High cd,Red SW Strobe,Standard cd,White P2RH-P 2-Wire Horn Strobe,High cd,Red,Plain SW-P Strobe,Standard cd,White,Plain P2W 2-Wire Horn Strobe,Standard cd,White SWH Strobe,High cd,White P2W-P 2-Wire Horn Strobe,Standard cd,White,Plain SWH-P Strobe,High cd,White,PlainI P2WH 2-Wire Horn Strobe,High cd,White Horns P2WH-P 2-Wire Horn Strobe,High cd,White,Plain HR Horn,Red P4R 4-Wire Horn Strobe,Standard cd,Red HW Horn,White I P4R-P 4-Wire Horn Strobe,Standard cd,Red,Plain Accessories P4RH 4-Wire Horn Strobe,High cd,Red TR-HS Trim Ring,Wall,Red P4W 4-Wire Horn Strobe,Standard cd,White SBBR Indoor Surface Mount Back Box,Red Wall Strobes SBBW Indoor Surface Mount Back Box,White I SR Strobe,Standard cd,Red SR-P Strobe,Standard cd,Red,Plain SR-SP Strobe,Standard cd,Red,"FUEGO" I Notes: All-P models have a plain housing(no"FIRE"marking on cover) All-SP models have"FUEGO"marking on cover I "Standard cd"refers to strobes that include 15,15/75,30,75,95,110,and 115 candela settings. "High cd"refers to strobes that include 135,150,177,and 185 candela settings. SYSTEM 3825 Ohio Avenue•St.Charles, IL 60174 02014 System Sensor. I Phone:800-SENSOR2•Fax:630-377-6495 Product specifications subject to change without notice.visit systemsensor.com SENSOR afor current product information,including the latest version of this data sheet. www.SystemsenSOLCOm AVDS10201.1/14