Specifications ,e-/A-40.20
//
RECEIVED 71/o 5 5w l e �G, Cepthn D.-
//1rR 22 zen i 670
CITY OF TIGA D A t qC0 Fire & Builcki r IIVG DIVISION
Products Gem
Customer Service /Sales:
Technical Services: Tel: (800) 381 -9312 / Fax (800) 791 -5500 Tel: (414) 570 -5000 / (800) 558 -5236
Fax: (414) 570 -5010 / (800) 877 -1295
Series TY -FRB — Z8, 4.2, 5.6, and 8.0 K- factor
Upright, Pendent, and Recessed Pendent Sprinklers
Quick Response, Standard Coverage
General chemical to which the sprinklers will be
exposed.
An intermediate level versions of the
Description F-F '
Series TY -FRB Pendent Sprinklers are .��
•
detailed in Technical Data Sheet � _ - . , � ,
The S eries TY-FRB, 2.8, 4.2, 5.6, and TFP356, and Sprinkler Guards are de
■
8.0 K- factor, Upright and Pendent p
Sprinklers described in this data sheet tailed in Technical Data Sheet TFP780 1 . - 1 --- - :
are quick response standard cover
age, decorative 3 mm glass bulb type WARNINGS , t t % ,�,
spray sprinklers designed for use in The Series TY -FRB Sprinklers de- - - �,
light or ordinary hazard, commercial scribed herein must be installed and
occupancies such as banks, hotels, maintained in compliance with this Y. .
document, as well as with the a lica- "
shopping malls, etc ble standards of the National Fire
The recessed version of the Series tection Association, in addition to the
TY -FRB Pendent Sprinkler, where ap- standards of any other authorities hay- �rr1
placable, is intended for use in areas ing jurisdiction. Failure to do so may
with a finished ceiling. It uses either a impair the integrity of these devices. —=
two -piece Style 10 (1/2 inch NPT) or
Style 40 (3/4 inch NPT) Recessed Es- The owner is responsible for maintain- y:
cutcheon with 1/2 inch (12,7 mm) of ing their fire protection system and de- �?
recessed adjustment or up to 3/4 inch vices in proper operating condition. , " • ;' j
(19,1 mm) of total adjustment from the The installing contractor or sprinkler 'i ,•�
flush pendent position, or a two -piece manufacturer should be contacted
to any questions. \` ti ^
Style 20 (1/2 inch NPT) or Style 30 (3/4 y 9 . r •
inch NPT) Recessed Escutcheon with
1/4 inch (6,4 mm) of recessed adjust-
ment or up to 1/2 inch (12,7 mm) of Model/Sprinkler rinkler
total adjustment from the flush pen- Maximum Working Pressure
dent position. The adjustment provided Identification 175 psi (12,1 bar)
by the Recessed Escutcheon reduces Discharge Coefficient
the accuracy to which the fixed pipe Numbers K = 2.8 GPM /psili (40,3 LPM /barl'
drops to the sprinklers must be cut. K = 4.2 GPM /psi (60,5 LPM/bar
Corrosion resistant coatings, where TY1131 - Upright 2.8K, 1/2 "NPT K = 5.6 GPM /psi (80,6 LPM /bar
applicable, are utilized to extend the TY1231 - Pendent 2.8K, 1/2 "NPT K = 8.0 GPM /psi (115,2 LPM /bar
• life of copper alloy sprinklers beyond TY2131 - Upright 4.2K, 1/2 "NPT Temperature Ratings
that which would otherwise be ob- TY2231 - Pendent 4.2K, 1/2 "NPT Refer to Table A and B
r tained when exposed to corrosive at- TY3131 - Upright 5.6K, 1/2 "NPT
mospheres. Although corrosion resis- TY3231 - Pendent 5.6K, 1/2 "NPT Finishes
tant coated sprinklers have passed the TY4131 - Upright 8.0K, 3/4 "NPT Sprinkler: Refer to Table A and B
standard corrosion tests of the apple- TY4231 - Pendent 8.0K, 3/4 "NPT Recessed Escutcheon: White Coated,
cable approval agencies, the testing is Chrome Plated, or Brass Plated m
not representative of all possible cor- E
rosive atmospheres. Consequently, it Technical Physical Characteristics E
is recommended that the end user be Data Frame Bronze I-
consulted with respect to the suitability Button Brass /Copper °'
of these coatings for any given corro- Approvals Sealing Assembly 0
slue environment. The effects of amb UL and C -UL Listed. Beryllium Nickel w/Teflont 0
ent temperature, concentration of FM, LPCB, and NYC Approved. Bulb Glass CC
chemicals, and gas /chemical velocity, (Refer to Table A for complete approval Compression Screw . . . Bronze o
should be considered, as a minimum, information includin corrosion rests Deflector Copper /Bronze a
along with the corrosive nature of the g Bushing K =2.8
tant status.) 9 ( ) Bronze
Page 1 of 8 APRIL, 2003 TFP171
Page2of8 TFP171
1
ESCUTCHEON 7/16" (11,1 mm) STYLE 10 or 20
PLATE SEATING NOMINAL RECESSED SSU*
SURFACE
1/2', MAKE -IN ESCUTCHEON
NPT I DEFLECTOR
2 -1/4° f urw 7/16"
I. 5
(57,2 mm) �I I (11,1 mm) /li
4
} = ff`� NOMINAL
I 111111 �� MAKE IN w 2
1- 9/16" � " � 2- 3/16 ; A
(39,7 mm) FLATS _ / (55,6 mm) 7/, 3
II
/ /l1 \� , /l!� \� I 7
SSP DEFLECTOR * 2 -7/8" (73,0 mm) DIA. 1/2° NPT t
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
"I
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
• 2 - Button Assembly 5 - Compression 7 - Bushing orifice seat on frame.
Screw * * Pipe thread connections per ISO 7/1 can be provided on
special request. _ _
FIGURE 1
QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY1131) AND PENDENT (TY1231) SPRINKLERS
2.8 K- FACTOR, 1/2 INCH NPT
ESCUTCHEON 7/16" (11,1 mm) STYLE 10 or 20
PLATE SEATING 1/2 ** NOMINAL RECESSED SSU*
SURFACE NPT MAKE -IN ESCUTCHEON DEFLECTOR
1 6*
MEM-
ai'�171Rp. ' ���� �,:.
/I
l i .
1111 3 2 3/16" ��r� I ( 11,1 1 m'm ) I 5
(55,6 mm) 111 NOM INAL ; 4
AKE -IN
ill IF
(38,1 / I mm) I ' WRENCH �� 1 2-3/16" 2
1 (55,6 mm) 1 VI II FLATS I 3
f i I = 1
SSP DEFLECTOR * - F — 2 -7/8° (73,0 mm) DIA. 1/2° NPT I
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing a - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame.
Screw * * Pipe thread connections per ISO 7/1 can be provided on
• special request
FIGURE 2
QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY2131) AND PENDENT (TY2231) SPRINKLERS
4.2 K- FACTOR, 1/2 INCH NPT
TFP171 Page 3 of 8
I
ESCUTCHEON 7/16" (11,1 mm) STYLE 10 or 20
PLATE SEATING * * NOMINAL RECESSED SSU*
SURFACE 1/2" MAKE -IN ESCUTCHEON
NPT DEFLECTOR
t -rr- , �,
2-3/16" -� � 1'• ,� 11.116 '�/ 5
( )
(55,6 mm) =A ��_ rit,14 — NOMIN ' 4
MAKE -IN
�� I 2- 3/16" fro 'y 2
ill (38,1 mm FLATS _ (55,6 mm) V 3
,, i I
SSP DEFLECTOR * - F — 2 -7/8° (73,0 mm) DIA i 1/2" NPT ** I
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame
Screw ** Pipe thread connections per ISO 7/1 can be provided on
special request
FIGURE 3
QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY3131) AND PENDENT (TY3231) SPRINKLERS
5.6 K- FACTOR, 1/2 INCH NPT
ESCUTCHEON 1/2" (12,7 mm) STYLE 30 or 40
PLATE SEATING 3/4" ** NOMINAL RECESSED SSU*
SURFACE NPT MAKE-IN ESCUTCHEON DEFLECTOR iiiillirrIl
2-5/16' 1/2" I f ' 5
�� �� (12,7 mm) I
(58,7 mm) .� . NOMINAL ��� - I 1 4
- MAKE -IN
1- 9/16" I I 2-1 /a• y + ' .' 2
(39,7 mm) FLATSH (57 mm) -1 V 3
a 65
SSP DEFLECTOR -*-- 2 -7/8° (73,0 mm) DIA. 3/4" NPT }
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
") 2 - Button Assembly 5 - Compression orifice seat on frame.
Screw ** Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 4
QUICK RESPONSE SERIES TY -FRB UPRIGHT (TY4131) AND PENDENT (TY4231) SPRINKLERS
8.0 K- FACTOR, 3/4 INCH NPT
Listing is based on the requirements of
Operation Design NFPA 13, and FM Approval is based
ia
C on the requirements of FM's Loss Pre -
The glass Bulb contains a fluid which vention Data Sheets ). Only the Style
expands when exposed to heat. When 10, 20, 30, or 40 Recessed Escutch-
the rated temperature is reached, the The Series TY -FRB Pendent and Up- eon, as applicable, is to be used for
fluid expands sufficiently to shatter the right Sprinklers are intended for fire recessed pendent installations.
glass Bulb, allowing the sprinkler to protection systems designed in ac-
activate and water to flow. cordance with the standard installation
rules recognized by the applicable
Listing or Approval agency (e.g., UL
Page 4 of 8 TFP171
/ SPRINKLER FINISH (See Note 7)
K Installation
TYPE TEMP. BULB NATURAL CHROME WHITE*"
LIQUID BRASS PLATED POLYESTER The Series TY -FRB Sprinklers must be
installed in accordance with the follow -
135°F/57°C Orange ing instructions
PENDENT 155 °F /68 °C Red
(TY1231) 1, 2, 3. 5 NOTES
and 175 °F /79 °C Yellow Do not install any bulb type sprinkler if
UPRIGHT 200 °F /93 °C Green the bulb is cracked or there is a loss of
2 8 (TY1131) liquid from the bulb. With the spnnkler
286F/141°C Blue held horizontally, a small air bubble
1/2°
NPT 135 °F /57 °C Orange should be present. The diameter of the
RECESSED air bubble is approximately 1/16 inch
PENDENT 155 °F /68 °C Red (1,6 mm) for the 135 °F /57 °C to 3/32
(TY2231)• 175 °F /79 °C Yellow inch (2,4 mm) for the 286 °F /141 °C
temperature ratings.
Figure 5 200 °F /93 °C Green 1, 2, 5 A leak tight 1/2 inch NPT sprinkler joint
135 °F /57 °C Orange should be obtained with a torque of 7
RECESSED 155 °F /68 °C Red to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi-
•
PENDENT mum of 21 ft. lbs. (28,5 Nm) of torque
(TY2231r 175 °Ff79 °C Yellow may be used to install sprinklers with
Figure 6 200 °F /93 °C Green 1/2 NPT connections. A leak tight 3/4
inch NPT sprinkler joint should be ob-
135°F/57°C Orange tained with a torque of 10 to 20 ft.lbs.
PENDENT 155 °F /68 °C Red (13,4 to 26,8 Nm). A maximum of 30
(TY2231) ft.lbs. (40,7 Nm) of torque is to be used
and 175 °F /79 °C Yellow to install sprinklers with 3/4 NPT con -
UPRIGHT 200 °F /93 °C Green nections. Higher levels of torque may
(TY3131) distort the sprinkler inlet and cause
4.2 286 °F /141 °C Blue 1 2 leakage or impairment of the sprinkler.
NPT 135 °F /57 °C Orange Do not attempt to make -up for insuffi-
RECESSED 155 °F /68 °C Red dent adjustment in the escutcheon
PENDENT plate by under- or over- tightening the
(TY2231)• 175 °F /79 °C Yellow sprinkler. Readjust the position of the
Figure 7 2OOF/93°C Green sprinkler fitting to suit.
The Series TY -FRB Pendent and Up-
135°F/57°C Orange right Sprinklers must be installed in
RECESSED 155 °F /68 °C Red accordance with the following instruc-
PENDENT
tions.
(TY2231)** 175 °F /79 °C Yellow
Step 1. Pendent sprinklers are to be
Figure 8 200 °F /93 °C Green installed in the pendent position, and
upright sprinklers are to be installed in
NOTES: the upright position.
1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers.
2. Listed by Underwriters Laboratories, Inc for use in Canada (C -UL) as Quick Response Step 2. With pipe thread sealant ap-
Sprinklers. plied to the pipe threads, hand tighten
3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Spnn- the sprinkler into the sprinkler fitting.
klers.
5. Approved by the City of New York under MEA 354 -01 -E. Step 3. Tighten the sprinkler into the
7. Where Polyester Coated Sprinklers are noted to be UL and C -UL Listed, the sprin-
sprinkler fitting using only the W
klers are UL and C -UL Listed as Corrosion Resistant Sprinklers. 6 Sprinkler Wrench (Ref. Figure 13).
• Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4° Total Adjustment Re- With reference to Figures 1, 2, 3, and
cessed Escutcheon, as applicable. 4, the W - Type 6 Sprinkler Wrench is to
• - Installed with Style 20 (1/2° NPT) or Style 30 (3/4° NPT) 1/2" Total Adjustment Re- be applied to the sprinkler wrench
cessed Escutcheon, as applicable. flats.
"' Frame and Deflector only. Listings and approvals apply to all colors (Special Order)
N /A. Not Available
The Series TY -FRB Recessed Pen-
dent Sprinklers must be installed in
TABLE A accordance with the following instruc-
LABORATORY LISTINGS AND APPROVALS tions.
2.8 AND 4.2 K- FACTOR SPRINKLERS Step A. After installing the Style 10.
20, 30, or 40 Mounting Plate, as appli-
cable, over the sprinkler threads and
with pipe thread sealant applied to the
pipe threads, hand tighten the sprin-
kler into the sprinkler fitting.
Step B Tighten the sprinkler into the
TFP171 Page 5 of 8
I
SPRINKLER FINISH (See Note 7)
K TYPE TEMP. BULB NATURAL CHROME WHITE ** LEAD
LIQUID BRASS PLATED POLYESTER COATED
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
(TY3231) 1, 2, 3. 4, 5, 6 1, 2, 3, 5
and 175 °F /79 °C Yellow
UPRIGHT 200 °F /93 °C Green
5.6 (TY3131)
286 °F /141 °C Blue
1/2"
NPT 135 °F /57 °C Orange
RECESSED 155 °F /68 °C Red
PENDENT 1, 2, 4, 5 N/A
(TY3231)' 175 °F /79 °C Yellow
Figure 9 200 °F /93 °C Green
135 °F /57 °C Orange
RECESSED 155F/68°C Red
• PENDENT 1. 2, 3, 4, 5 1, 2, 4, 5 N/A
(TY3231)** 175 °F /79 °C Yellow
Figure 10 200 °F /93 °C Green
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
(TY4231) 175 °F /79 °C Yellow 1, 2, 3, 4, 5, 6 1, 2, 5
UPRIGHT 200 °F /93 °C Green
8.0 (TY4131)
286 °F /141 °C Blue
3/4"
NPT 135 °F /57 °C Green
RECESSED 155 °F /68 °C Orange
PENDENT 1, 2, 4, 5 N/A
(TY4231)* 175 °F /79 °C Red
Figure 11 200 °F /93 °C Yellow
135 °F /57 °C Orange
RECESSED 155F/68°C Red
PENDENT 1, 2, 3, 4, 5 N/A
(TY4231)'° 175 °F /79 °C Yellow
Figure 12 200 °F /93 °C Green
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL) as Quick Response Sprinklers
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C -UL) as Quick Response Sprinklers.
3. Approved by Factory Mutual Research Corporation (FM) as Quick Response Sprinklers.
4. Approved by the Loss Prevention Certification Board (LPCB) as Quick Response Sprinklers; however, the LPC does not rate the thermal
sensitivity of recessed sprinklers.
5. Approved by the City of New York under MEA 354 -01 -E.
6. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31 -53- 428- 4444/Fax 31 -53- 428 - 3377).
7. Where Polyester Coated and Lead Coated Sprinklers are noted to be UL and C -UL Listed, the sprinklers are UL and C -UL Listed as
Corrosion Resistant Sprinklers. Where Lead Coated Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as a
Corrosion Resistant Sprinklers.
Installed with Style 10 (1/2° NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable.
Installed with Style 20 (1/2" NPT) or Style 30 (3/4" NPT) 1/2" Total Adjustment Recessed Escutcheon, as applicable.
"" Frame and Deflector only. Listings and approvals apply to all colors (Special Order).
N/A Not Available
TABLE B
LABORATORY LISTINGS AND APPROVALS
5.6 AND 8.0 K- FACTOR SPRINKLERS
sprinkler fitting using only the W -Type Step C. After the ceiling has been in-
7 Recessed Sprinkler Wrench (Ref. stalled or the finish coat has been ap-
Figure 14). With reference to Figure 1, plied, slide on the Style 10, 20, 30, or
2, 3, and 4, the W -Type 7 Recessed 40 Closure over the Series TY -FRB
Sprinkler Wrench is to be applied to Sprinkler and push the Closure over
the sprinkler wrench flats. the Mounting Plate until its flange
comes in contact with the ceiling.
N
Page 6 of 8 TFP171
2 -7/8" DIA 2 -7/8" DIA
(73,0 mm) 3/4° (19.1 mm) (73,0 mm ) I
518.1/4"
1/2x1/8" 1/2" (12.7 mm)
(15.9±6,4 mm) F . 2 -1/4' DIA 1/4" (6,4 mm) (12.7±3.2 mm) " DIA. 1/4° (6,4 mm)
2 -1/4
FACE OF (57.2 mm) MOUNTING FACE OF (57,2 mm)
SPRINKLER PLATE SPRINKLER MOUNTING
FITTING FITTING PLATE
1/8" 1/8'
' (3.2 mm) +� (3.2 mm) .,,,,,,J...
,.....„,,,,.. - � I MOUNTING IF
MOUNTING I SURFACE
SURFACE .. �i. t
CLOSURE SERIES 1- 5/16" (33.3 mm)I CLOSURE SERIES 1 -5/16' (33.3 mm)I
TY -FRB 13/16' (20.6 mm) TY -FRB 1 -1/16° (27,0 mm)
FIGURE 5 FIGURE 6
SERIES TY -FRB RECESSED PENDENT SERIES TY -FRB RECESSED PENDENT
WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT
. , STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON
2.8 K- FACTOR, 1/2 INCH NPT 2.8 K- FACTOR, 1/2 INCH NPT
I. 2 -7/8" DIA. 2 -7/8° DIA -
5/8 ±1/4'
(73,0 mm) 3/4' (19,1 mm) (73,0 mm )
1/2±1/8" 1/2' (12,7 mm)
(15,9±6.4 mm) 2 -1/4' DIA 1/4' (6,4 mm) (12,7 ±3,2 mm)
F 2 -1/4° DIA. 1 1/4' (6,4 mm)
FACE OF (57.2 mm) MOUNTING FACE OF I (57,2 mm) MOUNTING
SPRINKLER PLATE SPRINKLER I PLATE
FITTING FITTING
1/8' 1/8'
1 - (3,2 mm) q (3. mm) • VA
i1r I \ - ,
MOUNTING u I MOUNTING SURFACE
SURFACE -.
CLOSURE SERIES 1 -1/4" (31,8 mm) CLOSURE SERIES 1 -1/4' (31,8 mm)
TY -FRB 3/4' (19,1 mm) TY -FRB 1' (25,4 mm)
FIGURE 7 FIGURE 8
SERIES TY -FRB RECESSED PENDENT SERIES TY -FRB RECESSED PENDENT
WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON
4.2 K- FACTOR, 1/2 INCH NPT 4.2 K- FACTOR, 1/2 INCH NPT
used to cover a clearance hole, may and after installation. Sprinklers dam -
Care and delay the time to sprinkler operation in aged by dropping, striking, wrench
- - a fire situation. twist/slippage, or the like, must be re-
Maintenance Sprinklers that are found to be leaking has a cracked Also, replace any sprinkler kler lost
The Series TY -FRB Sprinklers must be or exhibiting visible signs of corrosion liquid from its bulb. (Ref. Installation
maintained and serviced in accord- must be replaced. Section).
ance with the following instructions: Automatic sprinklers must never be Frequent visual inspections are rec-
NOTES painted, plated, coated or otherwise ommended to be initially performed for
altered after leaving the factory. Modi corrosion resistant coated
Before closing a fire protection system fied sprinklers must be replaced. an coa sprinklers,
main control valve for maintenance Sprinklers that have been exposed to after the Installation has been com-
work on the fire protection system that corrosive products of combustion, but pleted, to verify the integrity of the cor-
it controls, permission to shut down the have not operated, should be replaced rosion resistant coating. Thereafter,
affected fire protection system must be If they cannot be completely cleaned annual inspections per NFPA 25
obtained from the proper authorities by wiping the sprinkler with a cloth or should suffice; however, instead of in
and all personnel who may be affected by brushing it with a soft bristle brush. specting from the floor level, a random
by this action must be notified. sampling of close-up visual inspec
Care must be exercised to avoid dam- tions should be made, so as to better
Absence of an escutcheon, which is age to the sprinklers - before. during, determine the exact sprinkler condi-
° TFP171 Page7of8
• 2 -7/8" DIA _ 2 -7/8" DIA ,
5/6.1/x° (73,0 mm) 3/4' (19,1 mm) (73.0 mm)
_ 1/21/8" 1/2" (12.7 mm)
(15.9x6,4 mm) 2 -1/4' DIA ■ 1/4° (6,4 mm) (12.7x3,2 mm) 2 -1/4" DIA --1, 1/4" (6.4 mm)
FACE OF (57,2 mm) MOUNTING FACE OF (57.2 mm) I
SPRINKLER PLATE SPRINKLER I MOUNTING
PLATE
FITTING FITTING
1/8" 1/8'
°' (3.2 mm) t 47 (3,2 mm)
I ;4 M 11 " _.1
f IZ !rag I 1 \ - -----.....oln .... I I
MOUNTING I
MOUNTING � ■ I SURFACE '
SURFACE ^� --
/ I %.
CLOSURE SERIES 1 -1/4° (31,8 mm) CLOSURE SERIES 1 -1/4' (31,8 mm)
TY -FRB 3/4" (19,1 mm) TY -FRB 1' (25,4 mm)
FIGURE 9 FIGURE 10
SERIES TY -FRB RECESSED PENDENT SERIES TY -FRB RECESSED PENDENT
WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT
- . STYLE 10 RECESSED ESCUTCHEON STYLE 20 RECESSED ESCUTCHEON
5.6 K- FACTOR, 1/2 INCH NPT 5.6 K- FACTOR, 1/2 INCH NPT
• 2 -7/8' DIA. _j 2 -7/8' DIA
5 /8x1 /4° ( mm) I 3/4' (19.1 mm) (73,0 mm) 1/2" (12,7 mm)
1/2x1/8'
(15,936,4 mm) 2 -1/4' DIA 1/4" (6,4 mm) - (12,7x3.2 mm) 2 -1/4" DIA 1/4' (6,4 mm)
FACE OF (57,2 mm) (57,2 mm ) MOUNTING
FACE OF MOUNTING
SPRINKLER I PLATE SPRINKLER PLATE
FITTING FITTING
1 /8' 1/8'
" (3.2 mm) (3.2 mm)
._....-_•.11,1 I I• iii —1 r■ i ■ \ i 4
_� �� o r
MOUNTING
lip s I
MOUNTING SURFACE
SURFACE 11
CLOSURE SERIES 1 -5/16' (33,3 mm) CLOSURE SERIES 1 -5/16" (33,3 mm)I
TY -FRB 13/16" (20.6 mm) TY -FRB 1 -1/16' (27,0 mm)
FIGURE 11 FIGURE 12
SERIES TY -FRB RECESSED PENDENT SERIES TY -FRB RECESSED PENDENT
WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT WITH TWO -PIECE 1/2 INCH TOTAL ADJUSTMENT
STYLE 40 RECESSED ESCUTCHEON STYLE 30 RECESSED ESCUTCHEON
8.0 K- FACTOR, 3/4 INCH NPT 8.0 K- FACTOR, 3/4 INCH NPT
tion and the long term integrity of the
corrosion resistant coating, as it may WRENCH
r be affected by the corrosive conditions �' RECESS
present. /
WRENCH RECESS - y '
The owner is responsible for the in- - (END "A° USED FOR
spection, testing, and maintenance of 1/2° NPT MODELS)
their fire protection system and de- -...d vices In compliance with this docu- `
ment, as well as with the applicable WRENCH RECESS u,
N
standards of the National Fire Protec- END 3 °URED FOR PUSH WRENCH
tion Association (e.g., NFPA 25), in ( 3/4" NPT MODELS) INTO ENSURE
addition to the standards of any other ENGAGEMENT
authorities having jurisdiction. The in- WITH SPRINKLER
stalling contractor or sprinkler manu- FIGURE 13 WRENCHING AREA
facturer should be contacted relative to W -TYPE 6 SPRINKLER
any questions. WRENCH
It is recommended that automatic FIGURE 14
sprinkler systems be inspected, W -TYPE 7 RECESSED
tested, and maintained by a qualified SPRINKLER WRENCH
Inspection Service.
. Page 8 of 8 TFP171
•
P/N 57 - XXX - X - XXX
I I
TEMPERATURE
MODEL/SIN RATING
SPRINKLER
330 2.8K UPRIGHT (1/2 "NPT) TY1131 135 135 °F /57 °C
331 2.8K PENDENT (1/2 "NPT) TY1231 1 NATURAL BRASS 155 155 °F /68 °C
340 4.2K UPRIGHT (1/2 "NPT) TY2131 4 WHITE POLYESTER 175 175 °F /79 °C
341 4.2K PENDENT (1/2 °NPT) TY2231 9 CHROME PLATED 200 200 °F /93 °C
370 5.6K UPRIGHT (1/2 "NPT) TY3131 7 LEAD COATED 286 286 °F /141 °C
371 5.6K PENDENT (1/2 "NPT) TY3231
390 8.0K UPRIGHT (3/4 °NPT) TY4131
391 8.0K PENDENT (3/4 "NPT) TY4231
° • TABLE C
PART NUMBER SELECTION
SERIES TY -FRB PENDENT AND UPRIGHT SPRINKLERS
ORY, FOR INCIDENTAL, INDIRECT, cutcheon with (specify finish), P/N
Limited SPECIAL OR CONSEQUENTIAL (specify).
DAMAGES, INCLUDING BUT NOT
Warranty LIMITED TO LABOR CHARGES, RE- 1/2° (15 mm)
GARDLESS OF WHETHER TYCO Style 10
Products manufactured by Tyco Fire FIRE PRODUCTS WAS INFORMED Y Chrome Plated P/N 56 701 - - 010
Products are warranted solely to the 1 /2" e ABOUT THE POSSIBILITY OF SUCH Styy le 1 10 0
original Buyer for ten (10) years DAMAGES, AND IN NO EVENT White Color
against defects in material and work- SHALL TYCO FIRE PRODUCTS' LI- Coated P/N 56- 701 -4 -010
manship when paid for and properly ABILITY EXCEED AN AMOUNT 1/2" (15 mm)
installed and maintained under normal EQUAL TO THE SALES PRICE. Style Bra
use and service. This warranty will ex- 1/2 (1 5m �ted .... P/N 56- 701 -2 -010
pire ten (10) years from date of ship- THE FOREGOING WARRANTY I S Style 20 )
ment by Tyco Fire Products. No war- MADE /N LIEU OF ANY AND ALL Chrome Plated . . .. P/N 56- 705 -9 -010
ranty is given for products or OTHER WARRANTIES EXPRESS OR 1/2° (15mm)
components manufactured by compa
IMPLIED. INCLUDING WARRANTIES Style c lor
nies not affiliated by ownership with OF MERCHANTABILITY AND FIT- Coated P/N 56- 705 -4 -010
Tyco Fire Products or for products and NESS FOR A PARTICULAR PUR- 1/2' (16 mm)
components which have been subject POSE Style 20
to misuse, improper installation, corro- Brass Plated ... . . P/N 56 -705 -2 -010
3/a° mm)
sion, or which have not been installed, ( 30
maintained, modified or repaired in ac- Ordering Chr Plated .. .... P/N 56- 705 -9 -011
cordance with applicable Standards of ,/ 3/4" (20 mm)
the National Fire Protection Associa- Procedure Style 30
P tion, and /or the standards of any other white Color
Y Coated . ... P/N 56 -705 -4 -011
• • Authorities Having Jurisdiction. Mate - When placing an order, indicate the full 3/4' (20 mm)
vials found by Tyco Fire Products to be product name. Refer to the Price List Style 30
defective shall be either repaired or for com lete listing of Part Numbers. Brass Plated P/N 56- 705-2-011
replaced, at Tyco Fire Products' sole p g 3/4' (20 mm)
option. Tyco Fire Products neither as- Contact your local distributor for avail- Style 40
p y abillt Chrome Plated . . P/N 56- 700 -9 -010
sumes, nor authorizes any person to ability. 3/4' (20 mm)
assume for it, any other obligation in Style 40
connection with the sale of products or Sprinkler Assemblies with NPT White Color
parts of products. Tyco Fire Products Thread Connections: coated P/N 56- 700 -4 -010
shall not be responsible for sprinkler Specify: (Specify Model /SIN), Quick 3/4 mm)
system design errors or inaccurate or Response, (specify K- factor), (specify Brass Plated .. .. P/N 56-700-2-010
incomplete information supplied by temperature rating), Series TY -FRB
Buyer or Buyer's representatives. (specify Pendent or Upright) Sprinkler Sprinkler Wrench:
with (specify type of finish or coating), Specify: W -Type 6 Sprinkler Wrench,
IN NO EVENT SHALL TYCO FIRE P/N (specify from Table C). P/N 56- 000 -6 -387.
PRODUCTS BE LIABLE, IN CON-
TRACT, TORT, STRICT LIABILITY OR Recessed Escutcheon: Specify: W -Type 7 Sprinkler Wrench,
UNDER ANY OTHER LEGAL THE- Specify: Style (specify) Recessed Es- P/N 56- 850 -4 -001.
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446