Plans[Page Too Large for OCR Processing]
� ► c) S7__so 1 2_— 0000Co
`7000 SW RecL ci- c(
tqCO/Fire & Building CEVED
RE Products -- -
JAN 192012
Technical Services: Tel: (800) 381 -9312 / Fax: (800) 791 -5500 CITY OF TIGARD
BUILDING DIVISION
Series TY -B — 5.6 and 8,0 K- factor
Upright and Pendent Intermediate Level Sprinklers
Standard Response
GGener standard corrosion tests of the appli-
cable approval agencies, the testing is • i
not representative of all possible cor- .
Description rosive atmospheres. Consequently, it - - -r
is recommended that the end user be { ';
The Series TY-B, 5.6 and 8.0 K- factor consulted with respect to the suitability -:!. •
Upright and Pendent Intermediate of these coatings for any given corro-
Level Sprinklers described in this data sive environment. The effects of ambi-
sheet are automatic sprinklers of the ent temperature, concentration of r - •
"standard response" 5 mm frangible chemicals, and gas /chemical velocity, i +4
bulb type. They are "standard spray" should be considered, as a minimum,
sprinklers intended for use in fire sprin- along with the corrosive nature of the
kler systems designed in accordance chemical to which the sprinklers will be . :
with the standard installation rules rec- exposed.
ognized by the applicable Listing or
Approval agency (e.g., UL Listing is
based on NFPA requirements). Both WARNINGS
the Pendent and Upright Sprinklers -------
The Series TY -B Sprinklers described
produce a hemispherical water distri-
bution pattern below the deflector. herein must be installed and main-
tained in compliance with this docu-
Intermediate Level Sprinklers are pri- ment, as well as with the applicable TI marily designed for use in rack storage standards of the National Fire Protec- sprinkler systems where their ther- tion Association, in addition to the mally sensitive elements must be standards of any other authorities hay-
shielded from the water spray of higher ing jurisdiction. Failure to do so may
elevation sprinklers that could operate impair the performance of these de-
earlier during a fire. Intermediate Level vices. .... -.
Sprinklers are also used in other appli-
cations such as beneath open gridded The owner is responsible for maintain
catwalks. ing their fire protection system and de-
vices in proper operating condition.
Corrosion resistant coatings, where The installing contractor or sprinkler
applicable, are utilized to extend the manufacturer should be contacted Technical
life of copper alloy sprinklers beyond with any questions.
that which would otherwise be ob- Data
tained when exposed to corrosive at-
mospheres. Although corrosion resis- Approvals
tant coated sprinklers have passed the Model /Sprinkler UL and C -UL Listed.
FM and NYC Approved.
Identification (Refer to Table A for complete approval
information including corrosion resis-
IMPORTANT Numbers tant status.)
Always refer to Technical Data
Maximum Working Pressure E
Sheet TFP700 for the "INSTALLER
WARNING" that provides cautions TY3153 - Upright 5.6K, 1/2 "NPT 175 psi (12,1 bar) a
TY3251 - Pendent 5.6K, 1/2 "NPT
with respect to handling and instal-
TY4153 - Upright 8.0K , 3/4 "NPT Discharge Coefficient -0
lation of sprinkler systems and corn- TY4251 - Pendent 8.0K, 3/4 "NPT K = 5.6 GPM /psi (80,6 LPM /bar / E
ponents. Improper handling and in- K = 8.0 GPM /psi (115,2 LPM /bar a)
stallation can permanently damage N
a sprinkler system or its compo Temperature Ratings a
nents and cause the sprinkler to fail Refer to Table A °C
--- to operate in a fire situation or cause Finishes a
i to operate prematurely. Sprinkler: Refer to Table A o
4-
Page 1 of 6 JANUARY, 2005 YFP351
Page 2 of 6 TFP351
e 7/16" (11,1 mm) - - - 1/2 " ** - - - - - 3 -1/2" - (88,9 mm) DIA,
NOMINAL MAKE -IN NPT
0-RING SHIELD SCREW mu
( A 7rr� %
p` I UPRIGHT _ ∎� 7/16"
2 3/16" SHIELD * (11,1 mm) 2.3/8"
(55,6 mm) MODEL S2 WRENCHING NOMINAL (60,3 mm)
SHIELD FLATS r MAKE IN
WRENCHING �
FLATS
- 3 -1/2" (88,9 mm) DIA, - 1/2" ** f
NPT
PENDENT UPRIGHT
(FIELD ASSEMBLED - SEE INSTALLATION SECTION) (FACTORY ASSEMBLED)
* Temperature rating is indicated on the deflector, shield, or adjacent to orifice seat on frame.
** Pipe thread connections per ISO 7/1 can be provided on special request.
FIGURE 1
STANDARD RESPONSE SERIES TY -B UPRIGHT (TY3153) AND PENDENT (TY3251) SPRINKLERS
INTERMEDIATE LEVEL SPRINKLERS, 5.6 K- FACTOR, 1/2 INCH NPT
1/2" (12,7 mm) 3/4 " ** 3 -1/2" (88,9 mm) DIA, -
NOMINAL MAKE -IN NPT
1 SHIELD
1 O RING SCREW -
/ ��
/
2- 5/16"
11111111 UPRIGHT 1/2"
(58,7 mm) MODEL S2 117 WRENCHING SHIELD * (12,7 mm) 2 7/16"
I SHIELD FLATS ,. = NOMINAL (61,9 mm)
NI° WRENCHING -
FLATS MAKE -IN
3 -1/2" (88,9 mm) DIA, -
PENDENT NPT UPRIGHT
(FIELD ASSEMBLED - SEE INSTALLATION SECTION) (FACTORY ASSEMBLED)
* Temperature rating is indicated on the deflector, shield, or adjacent to orifice seat on frame. .
* * Pipe thread connections per ISO 7/1 can be provided on special request.
FIGURE 1
J
STANDARD RESPONSE SERIES TY -B UPRIGHT (TY4153) AND PENDENT (TY4251) SPRINKLERS
INTERMEDIATE LEVEL SPRINKLERS, 8.0 K- FACTOR, 3/4 INCH NPT
TFP351 Page 3 of 6
SPRINKLER FINISH (See Note 5)
_K _ _ _ TYPE - - .TEMP. -- . - .BULB- ... - - - - -- NATURAL - • LEAD - -WAX — WAX OVER
LIQUID BRASS"" COATED COATED LEAD COATED
135 °F /57 °C Orange
UPRIGHT 155 °F /68 °C Red
5.6 (TY3153) 1. 2, 3, 4 1. 2, 3, 4 1, 2. 3. 4 1, 2, 3, 4
1/2" 175 °F /79 °C Yellow
NPT 200 °F /93 °C Green
286 °F /141 °C Blue 1".2", 3" 4" 1 1•• 2" 3•' 4'•
360 °F /182 °C Mauve I N/A
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
(TY3251) 1, 2, 3, 4 N/A
175 °F /79 °C Yellow
200 °F /93 °C Green
286 °F /141 °C Blue
360 °F /182 °C Mauve
•
135 °F /57 °C Orange
UPRIGHT 155 °F /68 °C Red
8 (TY4153) 1, 2, 3, 4 1, 2, 3, 4 1, 2, 3, 4 1, 2, 3, 4
3/4" 175 °F /79 °C Yellow
NPT 200 °F /93 °C Green
286 °F /141 °C Blue 1",2", 3", 4" I 1", 2", 3•', 4"
360 °F /182 °C Mauve I N/A
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
(TY4251) 1, 2, 3, 4 N/A
175 °F179 °C Yellow
200 °F /93 °C Green
286 °F /141 °C Blue
360 °F /182 °C Mauve
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL).
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C -UL).
3. Approved by Factory Mutual Research Corporation (FM).
4. Approved by the City of New York under MEA 354 -01 -E.
5. Where Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted to be UL and C -UL Listed, the sprinklers are UL
and C -UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted
to be FM Approved, the sprinklers are FM Approved as Corrosion Resistant Sprinklers.
•• 150 °F /66 °C Maximum Ceiling Temperature.
With Zinc Plated Shield.
N /A: Not Available
TABLE A
LABORATORY LISTINGS AND APPROVALS
Page 4 of 6 TFP351
Physical Characteristics — Upright Sprinklers —
Frame Bronze The Series TY -B Intermediate Level
Button •• - - Brass /Copper Upright Sprinklers must be installed in
Sealing Assembly accordance with the following instruc- wRENCH RECESS
Beryllium Nickel w/Teflont tions. (END "A° USED FOR
Bulb Glass 1/2" NPT MODELS)
Compression Screw Bronze Step 1 . With pipe thread sealant ap- r ,
Deflector Copper th sprinkler into the sprinkler fitting.
Shield Plated Steel
Step 2. Tighten the sprinkler into the WRENCH RECESS
sprinkler fitting using only the W -Type (END °B" USED FOR
Operation 6 Sprinkler Wrench (Ref. Figure 3), • 3/4° NPT MODELS)
except that an 8 or 10 inch adjustable
glass Bulb contains a fluid which
Crescent wrench is to be used for wax FIGURE 3
The
The glass
expands when exposed contains
to hea w When coated sprinklers. With reference to W -TYPE 6 SPRINKLER
the rted temperatue is reached, the Figure 1 or 2, the W -Type 6 Sprinkler WRENCH
Wrench or the Crescent wrench, as
fluid expands sufficiently to shatter the applicable, is to be applied to the
glass Bulb, allowing the sprinkler to wrench flats.
activate and water to flow. ing the wrench.
— Pendent Sprinklers — After installation, the sprinkler wrench
The Series TY-B Intermediate Level flats and frame arms must be in-
Pendent Sprinklers must be installed
Design accordance with the following in- spected and the wax coating re-
in a structions. n touched (repaired) whenever the coat -
Criteria ing has been damaged and bare metal
Step 1. Thread the S2 Shield onto the is exposed. The wax coating on the
The Series TY -B Pendent and Upright sprinkler threads with the stamped wrench flats can be retouched by gen-
Intermediate Level. Sprinklers are in- markings toward the deflector and just tly applying a heated 1/8 inch diameter
tended for fire protection systems de- to the end of the threads. The final steel rod to the areas of wax that have
signed in accordance with the stand- assembly step is easier to accomplish been damaged, to smooth it back over
and installation rules recognized by the if the Shield is not disengaged by con- areas where bare metal is exposed.
applicable Listing or Approval agency tinuing to turn the Shield past the
(e.g., UL Listing is based on the re- threads. NOTES
quirements of NFPA 13, and FM Ap- Step 2. Roll the 0-Ring over the sprin Only retouching of the wax coating ap-
proval is based on the requirements of plied to the wrench flats and frame
kler threads until it seats against the
FM's Loss Prevention'Data Sheets). Shield. arms i permitted, and the retouching
is to be performed only at the time of
Step 3. With pipe thread sealant ap- the initial sprinkler installation.
Installation plied to the pipe threads, hand tighten The steel rod should be heated only to
the sprinkler into the sprinkler fitting. the point at which it can begin to melt
The Series TY-B Sprinklers must be Step 4. Tighten the sprinkler into the the wax, and appropriate precautions
installed in accordance with the follow- sprinkler fitting using only the W -Type need to be taken, when handling the
ing instructions: 6 Sprinkler Wrench (Ref. Figure 3). heated rod, in order to prevent the
With reference to Figure 1 or 2, the installer from being burned.
NOTES W -Type 6 Sprinkler Wrench is to be If attempts to retouch the wax coating
Do not install any bulb type sprinkler if applied to the wrench flats. with complete coverage are unsuc-
the bulb is cracked or there is a loss of Step 5. Rotate the S2 Shield clockwise cessful, additional wax can be ordered
liquid from the bulb. With the sprinkler (looking up) so that it slightly corn- in the form of a wax stick (the end of
held horizontally, a small air bubble presses the O -Ring between the which is color coded). Only the correct
should be present. The diameter of the Shield and sprinkler fitting. color coded wax is to be used, and
air bubble is approximately 1/16 inch retouching of wrench flats and frame
(1,6 mm) for the 135 °F /57 °C to 3/32 arms is only permitted at the time of
inch (2,4 mm) for the 360 °F /182 °C — Wax Coated Sprinklers initial sprinkler installation. With the
temperature ratings. When installing wax coated sprinklers steel rod heated as previously de-
A leak tight 1/2 inch NPT sprinkler joint with the adjustable Crescent wrench, scribed, touch the rod to the area re-
should be obtained with a torque of 7 additional care needs to be exercised quiring additional wax with the rod an-
to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- to prevent damage to the wax coating gled downward, and then touch the
mum of 21 ft. lbs. (28,5 Nm) of torque on the sprinkler wrench flats or frame wax stick to the rod approximately one -
may be used to install sprinklers with arms and, consequently, exposure of half inch away from the area requiring
1/2 NPT connections. A leak tight 3/4 bare metal to the corrosive environ- retouching. The wax will melt and run
inch NPT sprinkler joint should be ob- ment. The jaws of the wrench should down onto the sprinkler.
tamed with a torque of 10 to 20 ft.lbs. be opened sufficiently wide to pass
(13.4 to 26,8 Nm). A maximum of 30 over the wrench flats without damag-
ft.lbs. (40,7 Nm) of torque is to be used ing the wax coating. Before wrench
to install sprinklers with 3/4 NPT con- tightening the sprinkler, the jaws of the
nections. Higher levels of torque may wrench are to be adjusted to just con -
distort the sprinkler inlet and cause tact the sprinkler wrenching flanges.
leakage or impairment of the sprinkler. After wrench tightening the sprinkler,
loosen the wrench jaws before remov-
TFP351 Page 5 of 6
It is recommended that automatic
Care and sprinkler systems be inspected, Ordering
tested, and maintained by -- - -
Maintenance Inspection Service in accordance with P rocedure
local requirements and /or national
The Series TY -B Sprinklers must be code. When placing an order, indicate the full
maintained and serviced in accord- product name. Refer to the Price List
ance with the following instructions: Limited for complete listing of Part Numbers.
NOTES Contact your local distributor for avail -
Before closing a fire protection system Warranty ability.
main control valve for maintenance
work on the fire protection system that Products manufactured by Tyco Fire Upright Sprinkler Assemblies with
it controls, permission to shutdown the Products are warranted solely to the Shield and NPT Thread
affected fire protection system must be original Buyer for ten (10) years Connections:
obtained from the proper authorities against defects in material and work- Specify: (Specify Model /SIN), Stand -
and all personnel who may be affected manship when paid for and properly and Response, (specify K- factor),
by this action must be notified. installed and maintained under normal (specify temperature rating), Series
use and service. This warranty will ex- TY -B Upright Intermediate Level Sprin-
Sprinklers that are found to be leaking Aire ten (10) years from date of ship- kler with (specify type of finish or coat -
or exhibiting visible signs of corrosion by Tyco Fire Products. No war- ing), P/N (specify from Table B).
must be replaced. ranty is given for products or
Automatic sprinklers must never be components manufactured by compa- Pendent Sprinkler Assemblies wi
painted, plated, coated or otherwise Hies not affiliated by ownership with (Shield Ordered Separately) and
altered after leaving the factory. Modi- Tyco Fire Products or for products and NPT Thread Connections:
Pied sprinklers must be replaced. components which have been subject Specify: (Specify Model /SIN), Stand
Sprinklers that have been exposed to to misuse, improper installation, corro- and Response, (specify K- factor),
corrosive products of combustion, but sion, or which have not been installed, (specify temperature rating), Series
have not operated, should be replaced maintained, modified or repaired in ac- TY-B Pendent Sprinkler with (specify
if they cannot be completely cleaned cordance with applicable Standards of type of finish or coating), P/N (specify
by wiping the sprinkler with a cloth or the National Fire Protection Associa- from Table C)
by brushing it with a soft bristle brush. tion, and /or the standards of any other M o d e l S2 Pendent Shield & O -Ring:
Authorities Having Jurisdiction. Mate- g:
Care must be exercised to avoid dam- pals found by Tyco Fire Products to be Specify: S2 Pendent Shield & 0-Ring
age to the sprinklers - before, during, defective shall be either repaired or for use with (specify 1/2" NPT or 3/4"
and after installation. Sprinklers dam replaced, at Tyco Fire Products' sole NPT) Series TY -B Pendent Sprinklers,
aged by dropping, striking, wrench P/N (specify).
option. Tyco Fire Products neither as-
twist/slippage, or the like, must be re- sumes, nor authorizes an y person to
placed. Also, replace any sprinkler that 1/2° NPT S2
has a cracked bulb or that has lost assume for it, any other obligation in Pendent Shield
liquid from its bulb. (Ref. Installation connection with the sale of products or & 0 -Ring P/N 56 -070 -9 -332
Section). parts of products. Tyco Fire Products 3 /4Pendent NPT
Shield
shall not be responsible for sprinkler
Frequent visual inspections are rec- system design errors or inaccurate or & 0-Ring P/N 56-070-9-342
ommended to be initially performed for incomplete information supplied by Sprinkler Wrench:
corrosion resistant coated sprinklers, Buyer or Buyer's representatives. Specify: W-Type 6 Sprinkler Wrench,
after the installation has been com- IN NO EVENT SHALL TYCO FIRE P/N 56- 000 -6 -387.
pleted, to verify the integrity of the cor- PRODUCTS BE LIABLE, IN CON -
rosion resistant coating. Thereafter, TRACT, TORT, STRICT LIABILITY OR Wax Sticks:
annual inspections per NFPA 25 UNDER ANY OTHER LEGAL THE- (for retouching wrench damaged
should suffice; however, instead of in- ORY, FOR INCIDENTAL, INDIRECT, wax coating)
specting from the floor level, a random SPECIAL OR CONSEQUENTIAL Specify: (Specify color) color coded
sampling of close -up visual inspec- DAMAGES, INCLUDING BUT NOT Wax Stick for retouching (specify tern-
bons should be made, so as to better LIMITED TO LABOR CHARGES, RE- perature rating) temperature rated Se-
determine the exact sprinkler condi- GARDLESS OF WHETHER TYCO rtes TY-B Sprinklers, P/N (specify).
tion and the long term integrity of the FIRE PRODUCTS WAS INFORMED
corrosion resistant coating, as it may ABOUT THE POSSIBILITY OF SUCH Black for 135°F. .... P/N 56 -065 -1 -135
be affected by the corrosive conditions DAMAGES. AND IN NO EVENT Red for 155 °F . P/N 56- 065 -1 -155
present. SHALL TYCO FIRE PRODUCTS' LI- Bu for 200 F and P/N 56 -065 -1 -175
The owner is responsible for the in ABILITY EXCEED AN AMOUNT 286 °F . ... P/N 56 -065 -1 -286
spection, testing, and maintenance of EQUAL TO THE SALES PRICE.
their fire protection system and de- THE FOREGOING WARRANTY IS NOTES
Each wax stick is suitable for retouch-
vices in compliance with this docu- MADE IN LIEU OF ANY AND ALL
' ment, as well as with the applicable OTHER WARRANTIES EXPRESS OR ing up to twenty-five sprinklers.
standards of the National Fire Protec- IMPLIED. INCLUDING WARRANTIES The wax used for 286 °F sprinklers is
tion Association (e.g., NFPA 25), in OF MERCHANTABILITY AND FIT- the same as for 200 °F sprinklers, and,
addition to the standards of any other NESS FOR A PARTICULAR PUR- therefore, the 286 °F sprinkler is limited
authorities having jurisdiction. The in- POSE. to the same maximum ceiling tempera -
stalling contractor or sprinkler manu- ture as the 200 °F sprinkler (i.e.,
facturer should be contacted relative to 150 °F).
any questions.
• Page 6 of 6 TFP351
- - P/N 57 -XXX- X XXX - -- -- - TEMPERATURE
RATING
SPRINKLER
MODEUSIN 135 135 °F /57 °C
533 5.6K UPRIGHT (1/2 "NPT) TY3153 1 NATURAL BRASS 155 155 °F /68 °C
543 8.0K UPRIGHT (3/4 "NPT) TY4153 7 LEAD COATED 175 175Ff79°C
6 WAX COATED 200 200 °F /93 °C
286°F/141°C MAX.
286 286°F/141°C
8 WAX OVER LEAD
286°F/141°C MAX. 360 360 °F /182 °C
TABLE B
PART NUMBER SELECTION
SERIES TY -B UPRIGHT INTERMEDIATE LEVEL SPRINKLERS
(UPRIGHT SHIELD INCLUDED WITH SPRINKLER)
P/N 57 - XXX - X - XXX
I I
TEMPERATURE
RATING
SPRINKLER
MODEUSIN 135 135 °F /57 °C
571 5.6K PENDENT (1/2 "NPT) TY3251 ( 1 NATURAL BRASS 155 155 °F /68 °C
591 8.0K PENDENT (3/4 "NPT) TY4251 175 175F/79°C
200 200 °F /93 °C
286 286°F/141°C
360 360F/182°C
TABLE C
PART NUMBER SELECTION
SERIES TY -B PENDENT SPRINKLERS
(MODEL S2 PENDENT SHIELD & 0-RING MUST BE SEPARATELY ORDERED)
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446