Plans 02/28/07 WED 09:51 FAX 15036560782 Master Fire Control (1002
l�
95 i - / i 0 0.:2007 -o0o5
A
t Fire & Building
Gem
Products
Customer Service/Sates:
Technical Services: Tel: (800) 381 -9312 / Fax: (800) 791 -5500 Tel: (414) 570 -5000 / (800) 558 -5236
Fax: (414) 570 -5010 / (800) 877 -1295
Series TY -B — 2. 5.6, nd 8.0 K- factor
Upright, Pendent, an Recessed Pendent Sprinklers
Standard Response, Standard Coverage
obtained by utilizing the Series TY e
General Pendent Sprinkler in combination with - -
Description the Model 82 Shield
WARNINGS
7
, ° 4.
The Series TY-B, 2.8, 5.6, and 8.0 The Series TY -B Sprinklers described , "y A,; : - r _ ..
.: ,.,., ; i 4 .
K- factor, Upright and Pendent Sprin- herein must be installed and main- t •' l : ;;; 117; klers described in this data sheet are tamed in compliance with this docu- , °" 1
standard response - standard cover- ment, as well as with the applicable ' It ', :i ,:. ,_..: ,; :"'
age, decorative 5 mm glass bulb type standards of the National Fire Protec- • c;.
spray sprinklers designed for use in ,,,,,.. . = .
—•_='
Y P 9 lion Association, in addition to the $ „14 ? :
light, ordinary, or extra hazard, corn- standards of any other authorities hay -
mercial occupancies such as banks, ing jurisdiction. Failure to do so may ' ” --
hotels, shopping malls, factories, refin- impair the integrity of these devices.
eries, chemical plants, etc. The owner is responsible for maintain-
The recessed version of the Series ing their fire protection system and de-
TY-B Pendent Sprinkler, where appli- vices in proper operating condition.
cable, is Intended for use in areas with The installing contractor or sprinkler ,•,•` ?: '' - ;_ ,."
;
a finished ceiling_ It uses a two -piece manufacturer should be contacted '.;,i,t `' ;,:- ;; `
•' _ _ ,, •
Style 10 (1/2 inch NPT) or Style 40 (3/4 relative to any questions. , ,,, ) ",'`.. l i .
inch NPT) Recessed Escutcheon. The i. i',v. I.' , . `; , ..
Recessed Escutcheon provides 1/2 ' 1 1.,
inch (12,7 mm) of recessed adjust- l ' I �� .,
ment or up to 3/4 inch (19,1 mm) of Model/Sprinkler 4 �
total adjustment from the flush en
dent position. The adjustment provided Identification T I l l +r1 r • -4 1.4
by the Recessed Escutcheon reduces '.
the accuracy to which the fixed pipe
drops to the sprinklers must be cut. 1VIJnlbe . ." _
".
Corrosion resistant coatings, where TY1151 - Upright 2.8K, 1/2"NPT Discharge Coefficient
applicable, are utilized to extend the TY1251 - Pendent 2.8K, 1/2"NPT K = 2.8 GPM /psis / (40,3 LPM/barl /
life of copper alloy sprinklers beyond TY3151 - Upright 5.6K,1/2 "NPT K = 5.6 GPM/psi (80,6 LPM/bar'n
that which would otherwise be ob- TY3251 - Pendent 5.6K, 1/2"NPT K = 8.0 GPM /psi (115,2 LPM/bar
tamed when exposed to corrosive at- TY4151 - Upright 8.0K, 3/4 "NPT
mospheres. Although corrosion rests- TY4251 - Pendent 8.0K, 3/4 "NPT Temperature Ratings
tant coated sprinklers have passed the TY4851 - Upright 8.0K, 1/2"NPT Refer to Table A
standard corrosion tests of the appll- TY4951 - Pendent 8.0K,1/2 "NPT Finishes
cable approval agencies, the testing is Sprinkler: Refer to Table A
not representative of all possible cor- Technical Recessed Escutcheon: White Coated,
rosive atmospheres. Consequently, it Chrome Plated, or Brass Plated
is recommended that the end user be Y
consulted with respect to the suitability ata Frame Physical al Characteristics Bronze E
of these coatings for any given corro- Approvals Button Brass /Copper B/Coer A
slue environment. The effects of ambi- UL and C -UL Listed. Sealing Assembly . r-
ent temperature, concentration of PM, LPCB, and NYC Approved. . . . . Beryllium Nickel w/Teflont 0
chemicals, and gas /chemical velocity, (RefertoTable A for complete a roval Bulb Glass d
should be considered, as a minimum, p PP N
along with the corrosive nature of the information including corrosion rests- Compression Screw . . . . Bronze m
chemical to which the sprinklers will be tant status.) Deflector Copper cc
exposed. Maximum Working Pressure Bushing (K =2.8) Bronze o
An intermediate level version of the 175 psi (12,1 bar) d
Series TY -B Pendent Sprinkler can be
o
Page 1 of 8 JANUARY, 2003 TFP751
02/28/07 WED 09:52 FAX 15036560782 Master Fire Control aI003
Page 2 of 6 TFP151
ESCUTCHEON 7/16" (11,1 mm)
PLATE SEATING " *-r, NOMINAL SSU
SURFACE N /2 MAKE -IN DEFLECTOR
2 -3/18'
2 -1/4^ = (55,6 mm) a
(57,2 mm) t �� t1 tilt » b i i 2
1.9/16" WRENCH := iiil 3
(39,7 mm) - t
- -_ ?0
II
i %G'!1 \� SSP* .�V 7
DEFLECTOR CROSS
PENDENT UPRIGHT SECTION
1 • Frame 3 - Sealing 4 • Bulb 6 • Deflector ' • Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly S - Compression 7 - Bushing orifice seat on frame.
Screw * * Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 1
STANDARD RESPONSE SERIES TY-5 UPRIGHT (TY1151) AND PENDENT (TY1251) SPRINKLERS
2.8 K- FACTOR, 1/2 INCH NPT
ESCUTCHEON 7/18" (11,1 mm) STYLE 10
PLATE SEATING ,, . . NOMINAL RECESSED *
SURFACE ,/2 MAKE -IN ESCUTCHEON S
F . . . _ .. .. _ _ i ____=._ __ NPT I DEFLECEC
TOR
7/15" � 5
INFM-
( 55 B m) I Il ip r/ NOMINAL lie
4
I MAKE - IN 1 - 1/2" ' ! �r 2.3/16' ,d 2
(38,1 mm) — (55.6 mm) A I f .
il WRENCH H _ _ l 0- 3
�.A�— -. _ - FIATS 1 4
SSP DEFLECTOR — - 2 -7/8° (73,0 mm) DIA - -I 1/2" NPT
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing a - Buro 6 - Deflector * Temperature rating Is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame.
Screw ** Pipe thread connections per 150 7/1 can be provided on
special request.
FIGURE 2
STANDARD RESPONSE SERIES TY-B UPRIGHT (TY3151) AND PENDENT (TY3251) SPRINKLERS
5.6 K- FACTOR, 1/2 INCH NPT
•
02/28/07 WED 09:52 FAX 15036560782 Master Fire Control 1 004
TFP151 Page 3 of 8
ESCUTCHEON 1/2° (12,7 mm) STYLE 40
PLATE SEATING ** NOMINAL RECESSED *
SURFACE Nf T M -IN ESCUTCHEON DEFLECTOR
1 6
1/2"
S 5
2-5/16° 4.1 if (12,7 mm)
(58,7 m 4 m) II II VIM 7 NOMINAL 4
_ � �
II �� MAKE -!N
1.9/16° I ��� 2 -1/a° j V Op (39,7mm — (57,2 mm)
-• - - - WREN =e . FLATS jq Y,f 1
SSP DEFLECTOR . — 2 -7/8" (73,0 mm) DIA. 3/4° NPT" t
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1- Frame 3 - Sealing 4 - Bulb S - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression 7 - Ejection orifice seat on frame -
Screw Spring * * Pipe thread connections per ISO 7/1 can be provided on
special request
FIGURE 3
STANDARD RESPONSE SERIES TY -B UPRIGHT (P14151) AND PENDENT (7Y4251) SPRINKLERS
8.0 K- FACTOR, 3/4 INCH NPT
ESCUTCHEON 7/16° (11,1 mm)
PLATE SEATING 1/2° ** NOMINAL SSU
1 SURFACE 1/2 MAKE -IN DEFLECTOR
* 6
r, b
2-1/4 ° 2 -3/16"
(57,2 mm) 4r = � i . , ' (55,6 mm) I i 4
�t r ' + 2
�
1 - 9/16" WRENCH
AT +r� y u
(39,7 mm) FLS 7 7 • 3
i °� 1 $ 1
SSP*
DEFLECTOR CROSS
PENDENT UPRIGHT SECTION
1 - Frame 3 • Sealing 4 • Bulb 6 • Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame.
Screw ** Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 4
STANDARD RESPONSE SERIES TY -B UPRIGHT (TY4851) AND PENDENT (TY4951) SPRINKLERS
8.0 K- FACTOR, 1/2 INCH NPT
02/28/07 WED 09:52 FAX 15036560782 Master Fire Control 0 005
• Page 4 of 8 TFP151
-
SPRINKLER FINISH (See Note 7) _
K TYPE TEMP. BULB NATURAL CHROME WHITE'" LEAD WAX WAX OVER
LIQUID BRASS PLATED POLYESTER COATED COATED LEAD COATED
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red 1, 2, 3 N/A
1122 " and
/ 175 °F /79 °C Yellow NPT UPRIGHT _ 200 °F /93 °C Green
(TY1151) 286 °F /141 °C Blue
360 °F /182 °C Mauve 1, 2
135 °F /57 Orange
PENDENT 155 °F /68 ° C Red
(TY3251) 1, 2, 3, 4, 5, 6 1, 2, 3, 5 1, 2, 3, 5 1, 2. 3, 5
and 175 °F /79 °C Yellow
UPRIGHT 200 °F /93 °C Green
5.6 (TY3151) ° 1",2", 3" 5" 1", 2"" 3 "' 5"
286 °F /141 C Blue
1/2° -
NPT 360 Mauve N/A
135 °F /57°C Orange
RECESSED 155 °F /68 °C Red
PENDENT 1, 2, 3, 5 1, 2, 5 N/A
FY3251)° 175 °F /79 °C Yellow
Figure 4 200 °F /93 °C Green
135 °F /57°C Orange
PENDENT 155 °F /68 °C Red
(TY4251) 1, 2, 5 1, 2, 3, 5 1. 2, 5
end 175'F/79°C Yellow 1, 2, 3.4, 5, 6
8.0 UPRIGHT 200 °F /93 °C Green
3/4'
(TY4151) 286 °F /141 °C Blue 1 ^Z"°, 3", 5 °' 1", 2", 5"
NPT `
380 °F /182 °C Mauve N/A
135 °F /57 °C Orange
RECESSED 155 °F /68 °C Red
PENDENT 1, 2, 3, 5 N/A
(TY4251)° 175 °F /79 °C Yellow
Figure 5 200 °F /93°C Green
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
8.0 (TY4951)
1/2" and 175 °F /79 °C Yellow 1, 2. 3, 5 N/A
NPT UPRIGHT 200 °F /93 °C Green
(TY4851) 286 °F /141 °C Blue
360'F/182 Mauve
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL).
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C -UL).
3. Approved by Factory Mutual Research Corporation (FM).
4, Approved by the Loss Prevention Certification Board (LPCB).
5- Approved by the City of New York under MEA 354 -01 -E.
6. VdS Approved (For details contact Tyco Fre & Building Products, Enschede. Netherlands, Tel. 31-53- 428- 4444/Fax 31 -53- 428 - 3377).
7. Where Polyester Coated, Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted to be UL and C-UL Listed, the
sprinklers are UL and C -UL Listed as Corrosion Resistant Sprinklers, Where Lead Coated, Wax Coated, and Wax over Lead Coated
Spnnlders are noted to be FM Approved, the sprinklers are FM Approved as Corrosion Resistant Sprinklers.
Installed with Style 10 (1 /2° NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable.
"^ 150 °F /66 °C Maximum Ceiling Temperature.
"" Frame and deflector only. Listings and approvals apply to all colors (Special Order).
N /A: Not Available
TABLE A
LABORATORY LISTINGS AND APPROVALS
02/28/07 WED 09:52 FAX 15036560782 Master Fire Control 1j006
- TFP151 Page 5 of 8
2-7/8' DIA- G
5/8±1/4" (73,0 mm) 3/4" (19,1 mm)
(15,91-6,4 mm) 1/4" (6,4 mm) WRENCH RECESS
2.1/4 " DIA. .. (END °A° USED FOR
FACE OF (57,2 mm) MOUNTING 1/2° N MODELS)
SPRINKLER PLATE
FITTING
�� 1 /8" WRENCH RECESS
lla •� l (3,2 mm) (ENO °B" USED FoR
3/4' NPT MODELS)
FIGURE 7
r l l W TYPE 6 SPRINKLER
�, ,� WRENCH
MOUNTING
Nil
SURFACE '
WRENCH
CLOSURE SERIES 1.1/4" (31,8 mm) , RECESS
TY-1B 3/4" (19,1 olii10-
FIGURE 5
SERIES TY -B RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO - PIECE 3/4 INCH TOTAL ADJUSTMENT
.447 ' 0 '
STYLE 10 RECESSED ESCUTCHEON ��,
56 K- FACTOR, 1/2 INCH NPT
PUSH WRENCH
IN TO ENSURE
ENGAGEMENT
2 -7 /8" DIA.
WITH SPRINKLER
5/8 ±1/4" (73 mm) 3/4" (19,1 mm� WRENCHING AREA
(15,9±6,4 mm) 2 -1/4" DIA. 1/4" (6,4 mm) FIGURE 8
FACE OF (57,2 mm) MOUNTING W -TYPE 7 RECESSED.
SPRINKLER PLATE SPRINKLER WRENCH
FITTING
1 /B"
I .Irll (3, mm) -
��� / Operation
+� t The glass Bulb contains a fluid which
expands when exposed to heat. When
MOUNTING �. the rated temperature is reached, the
SURFACE fluid expands sufficiently to shatter the
" -- glass Bulb, allowing the sprinkler to
CLOSURE SERIES 1- 5/16" (33,3 mm) activate and water to flow.
TY-8 13/16" (20,6 mm)
Design
FIGURE 6 Criteria
SERIES TY -B RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT The Series TY 8 Pendent and Upright
STYLE 40 RECESSED ESCUTCHEON Sprinklers are intended for fire protec-
8.0 K- FACTOR, 3/4 INCH NPT tion systems designed in accordance
with the standard installation rules rec-
ognized by the applicable Listing or
Approval agency (e.g., UL Listing is
based on the requirements of NFPA
13, and FM Approval is based on the
requirements of FM's Loss Prevention
Data Sheets). Only the Style 10 or 40
Recessed Escutcheon, as applicable,
is to be used for recessed pendent
installations.
02/28/07 WED 09:53 FAX 15036560782 Master Fire Control 0 007
' Page 6 of 8 TFP151
ing the wax coating. Before wrench stalled or the finish coat has been ap-
installation tightening the sprinkler, the jaws of the plied. slide on the Style 10 or 40 Clo-
wrench are to be adjusted to just con- sure over the Series TY-B Sprinkler
The Series TY-B Sprinklers must be tact the sprinkler wrench flats. After and push the Closure over the Mount -
installed in accordance with the follow- wrench tightening the sprinkler, loosen ing Plate until its flange comes in con-
ing instructions: the wrench jaws before removing the tact with the ceiling.
wrench.
NOTES After installation, the sprinkler wrench
Do not Install any bulb type sprinkler if flats and frame arms must be wrench
the bulb Is cracked or there is a loss of spatted and the wax coating re-
liquid from the bulb. With the sprinkler touched (repaired) whenever the coat -
held horizontally, a small air bubble ing has been damaged and bare metal
should be present. The diameter of the Is exposed. The wax coating on the
air bubble is approximately 1/16 Inch
(1,6 mm) for the 135F/57°C to 3/32 wrench flats can be retouched by gen-
inch (2,4 mm) for the 36oF/182°C tly applying a heated 1/8 inch diameter
temperature ratings. steel rod to the areas of wax that have
been damaged, to smooth it back over
A leak tight 1/2 inch NPT sprinkler joint areas where bare metal is exposed.
should be obtained with a torque of 7
to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- NOTES
mum of 21 ft. lbs. (28,5 Nm) of torque Only retouching of the wax coating ap-
may be used to install sprinklers with plied to the wrench flats and frame
1/2 NPT connections. A leak tight 3/4 arms is permitted, and the retouching
inch NPT sprinkler joint should be ob- is to be performed only at the time of
tained with a torque of 10 to 20 ft.lbs. the initial sprinkler installation.
(13,4 to 26,8 Nm). A maximum of 30 T steel rod should be heated only to
Vbs. lbs. (40,7Nm) of torque is to be used The
e point rod
which should can begin only to melt
n install Higher levels with o f 3/4 torque NPT con- orque may the wax, and appropriate precautions
disto r Nighr lels f t need to be taken, when handling the
distort the sprinkler inlet and cause heated rod, in order to prevent the
leakage or impairment of the sprinkler. installer from being burned.
Do not attempt to make -up for insuffi- cient adjustment in the escutcheon If attempts coating
wax f f at complete coverage ax ating
tempts to retouch the wa co
plate under- or over - tightening the cessful, additional wax can be ordered
sprinkler. Readjust the position of the
in the form of a wax stick (the end of
sprinkler fitting to suit. which is color coded). Only the correct
The Series TY -8 Pendent and Up- color coded wax is to be used, and
right Sprinklers must be installed in retouching of wrench flats and frame
accordance with the following Instruc- arms is only permitted at the time of
lions, initial sprinkler installation. With the
Step 1. Pendent sprinklers are to be steel rod heated as previously de-
installed in the pendent position, and scribed, touch the rod to the area re-
upright sprinklers are to be installed in quiring additional wax with the rod an-
the upright position. gled downward, and then touch the
wax stick to the rod approximately
Step 2. With pipe thread sealant ap- one -half inch away from the area re-
plied to the pipe threads, hand tighten quiring retouching. The wax will melt
the sprinkler into the sprinkler fitting. and run down onto the sprinkler.
Step 3. Tighten the sprinkler into the
sprinkler fitting using only the W -Type The Series TY -8 Recessed Pendent ,
6 Sprinkler Wrench (Ref. Figure 7), Sprinklers must be installed in ac-
except that an 8 or 10 inch adjustable cordance with the following instruc-
Crescent wrench is to be used for wax tions.
coated sprinklers. With reference to Step A. After installing the Style 10 or
Figures 1, 2 and 4 the 7 40 Mounting Plate, as applicable, over
Sprinkler Wrench enn ch or the e e adjustable the sprinkler threads and with pipe
Crescent wrench, as applicable is to thread sealant applied to the pipe
be applied to the wrench flats. threads, hand tighten the sprinkler into
When installing wax coated sprinklers the sprinkler fitting.
with the adjustable Crescent wrench, Step a lighten the sprinkler into the
- additional care needs to be exercised sprinkler rinkter fitting using only the W T e
to prevent damage to the wax coating 7 Recessed Sprinkler Sprinkler (Ref.
on the sprinkler wrench flats or frame
Figure 8). With reference to Figure 3 or
arms and, consequently, exposure of should 4, the Type reference
Recessed Sprinkler
merit. The jaws of the wrench shou
bare metal to the corrosive hoo ld d Wrench is to be applied to the sprinkler be opened sufficiently wide to pass wrench flats.
over the wrench flats without damag- Step C. After the ceiling has been in-
02/28/07 WED 09:53 FAX 15036560782 Master Fire Control 11008
• TFP151 Page 7 of 8
addition to the standards of any other
are and authorities having jurisdiction. The in- Lifl
stalling contractor or sprinkler manu- Warranty
Maintenance facturer should be contacted relative to
any questions.
The Series TY B Sprinklers must be Products manufactured by Tyco Fire
maintained and serviced in accord- It is recommended that automatic Products are warranted solely to the
ance with the following instructions: sprinkler systems be inspected, original Buyer for ten (10) years
tested, and maintained by a qualified against defects in material and work -
NOTES Inspection Service. manship when paid for and properly
Before closing a fire protection system installed and maintained under normal
main control valve for maintenance use and service. This warranty will ex-
work on the fire protection system that pire ten (10) years from date of ship -
it controls, permission to shut down the ment by Tyco Fire Products. No war-
affected fire protection system must be ranty is given for products or
obtained from the proper authorities components manufactured by compa-
and all personnel who may be affected nies not affiliated by ownership with
by this action must be notified. Tyco Fire Products or for products and
components which have been subject
Absence of an escutcheon, which is
to misuse, improper installation, corro-
used to cover a clearance hole, may sion, or which have not been installed,
delay the time to sprinkler operation 117 maintained, modified or repaired in ac-
a fire situation. cordance with applicable Standards of
Sprinklers that are found to be leaking the National Fire Protection Associa-
or exhibiting visible signs of corrosion Lion, and/or the standards of any other
must be replaced. Authorities Having Jurisdiction. Mate-
rials found by Tyco Fire Products to be
Automatic sprinklers must never be defective shall be either repaired or
painted, plated, coated or otherwise replaced, at Tyco Fire Products' sole
altered after leaving the factory. Modl- option. Tyco Fire Products neither as-
fied sprinklers must be replaced. sumes, nor authorizes any person to
Sprinklers that have been exposed to assume for it, any other obligation in
corrosive products of combustion, but connection with the sale of products or
have not operated, should be replaced parts of products. Tyco Fire Products
if they cannot be completely cleaned shall not be responsible for sprinkler
by wiping the sprinkler with a cloth or system design errors or inaccurate or
by brushing it with a soft bristle brush. incomplete information supplied by
Care must be exercised to avoid dam- Buyer or Buyer's representatives.
age to the sprinklers - before, during, IN NO EVENT SHALL TYCO FIRE
and after installation. Sprinklers dam- PRODUCTS BE LIABLE, IN CON -
aged by dropping, striking, wrench TRACT, TORT, STRICT LIABILITY OR
twist/slippage, or the like, must be re- UNDER ANY OTHER LEGAL THE -
placed. Also, replace any sprinkler that ORY, FOR INCIDENTAL. INDIRECT,
has a cracked bulb or that has lost SPECIAL OR CONSEQUENTIAL
liquid from its bulb. (Ref. Installation DAMAGES. INCLUDING BUT NOT
Section). LIMITED TO LABOR CHARGES, RE-
Frequent visual inspections are rec- GARDLESS OF WHETHER TYCO
ommended to be initially performed for FIRE PRODUCTS WAS INFORMED
corrosion resistant coated sprinklers, ABOUT THE POSSIBILITY OF SUCH
after the Installation has been corn- DAMAGES, AND IN NO EVENT
pleted, to verify the integrity of the cor- SHALL TYCO FIRE PRODUCTS' LI-
rosion resistant coating. Thereafter, ABILITY EXCEED AN AMOUNT
annual inspections per NFPA 25 EQUAL TO THE SALES PRICE.
should suffice; however, instead of in- IHE FORFGPING Wag ,IANTY (,,2
spectiog from the floor level, a random 14,4nE IN LIEU OF _ANY AND _ILL
sampling of close -up visual inspec- OTHER W BRANTIESEXPRESS_OR
tions should be made, so as to better JMPIJED WI WINGWARPJYTIES
determine the exact sprinkler condi- OF MERcHANTABILLTY AND FLT -
tlon and the long term integrity of the NESS FQB A PARTICULAR PUB-
. corrosion resistant coating, as it may BOIL
be affected by the corrosive conditions
present.
The owner is responsible for the in-
spection, testing, and maintenance of
their fire protection system and de-
vices in compliance with this docu-
ment, as well as with the applicable
standards of the National Fire Protec-
tion Association (e.g., NFPA 25), in
02/28/07 WED 09:54 FAX 15036560782 Master Fire Control 2009
Page 8 of 8 TFP1 51
P/N 57 - XXX --- X - XXX
TEMPERATURE
MODEL/SIN RATING
SPRINKLER
•
530 2.8K UPRIGHT (1 /2 TY1151 135 135 °F /57 °C
531 2.8K PENDENT (1/2 °NPT) TY1251 1 NATURAL BRASS 155 I55'F/68°C
•
570 5.6K UPRIGHT (1/2 "NPT) TY3151 4 WHITE POLYESTER 175 175 °F /79°C
a
571 5.6K PENDENT (1/2 "NPT) 1Y3251 9 f CHROME PLATED 200 200 °F /93 ° C
590 8.0K UPRIGHT (3/4 "NPT) TY4151 7 LEAD COATED 286 286 °F /141 °C
591 8.0K PENDENT (3/4 "NPT) TY4251 6 WAX COATED 380 360 °F /182 °C
286 °F /141 °C MAX.
560 8.0K UPRIGHT (1/2 "NPT) TY4851
_ 8 WAX OVER LEAD
561 8.0K PENDENT (1/2 "NPT) TY4951 286 °F /141 °C MAX
TABLE B
PART NUMBER SELECTION
SERIES TY -8 PENDENT AND UPRIGHT SPRINKLERS
Recessed Escutcheon: Wax Sticks:
Ordering Specify: Style (specify) Recessed Es- (tor retouching wrench damaged
cutcheon with (specify finish), P/N wax coating)
Procedure (specify). Specify: (Specify color) color coded
When placing an order, indicate the full 1/2' (15 mm) Wax Stick for retouching (specify tam
product name. Refer to the Price List Style 10 perature rating) temperature rated Se-
for complete listing of Part Numbers. Chrome Plated P/N 56- 701 -9.010 ries TY B Sprinklers, P/N (specify).
P 9 1/2" (15 mm)
Contact your local distributor for avail- st y l e 10 Black for 135 °F P/N 58- 065 -1•135
ability. Co tad Dior P/N 5 701 310 Red (or 155 °F . .. P/N 58 -0e -1 -155
1/2" (15 mm) Yellow for 175 °F P/N 56.065•1•175
Sprinkler Assemblies with NPT Style 10 Blue for 200 °F ano 286°F 286 °F PIN 56-065-1•286
Thread'Connections: Brass Plated P/N 58. 701.2 -010
Specify: (Specify Model/SIN), Stand- 3/4" (20 mm)
Response, (specify K- factor ,
Style ao NOTES
and Res
A ( Y ) Chrome Plated ... , PIN 56 -700-9 -010 Each wax stick is suitable for retouch-
(specify temperature rating), Series 5/4° (20 mm) ing up to twenty -five sprinklers.
TY -B (specify Pendent or Upright) Style 40
Sprinkler with (specify type of finish or White Color The wax used for 266 °F sprinklers is
coating), P/N (specify from Table B). Coated . . . .. . , , . P/N 56 - 4 - 010 the same as for 200 °F sprinklers, and,
3/4Style �o therefore, the 286 ° F sprinkler's limited
Brass Plated.. P/N 56 - 700 - 2 - 010 to the same maximum ceiling tempera-
ture as the 200 °F sprinkler (i.e.,
Sprinkler Wrench: 150 °F).
Specify: W-Type 6 Sprinkler Wrench,
P/N 56 -000 -6 -387.
Specify: W -Type 7 Sprinkler Wrench,
P/N 56-850-4-001.
TYCO FIRE PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19448