Plans . lr Pa oa�- a000l
tqcci Fire & Building _
Product -� l
JAN - 2 2007
Technical Services: Tel: (800) 381 -9312 / Fax: (800) 791 -5500 CC 6 y
L.4 E ht r. ,'��J
Series TY -B — 2.8, 5.6, and 8.0 K- factor
Upright, Pendent, and Recessed Pendent Sprinklers
Standard Response, Standard Coverage
cable approval agencies, the testing is
General not representative of all possible cor-
rosive atmospheres. Consequently, it ` " --
Description is recommended that the end user be 4 i I •
consulted with respect to the suitability +.:
The Series TY -B, 2.8, 5.6, and 8.0 of these coatings for any given corro- n `
K- factor, Upright and Pendent Sprin- sive environment. The effects of ambi-
klers described in this data sheet are ent temperature, concentration of
standard response - standard cover- chemicals, and gas /chemical velocity,
age, decorative 5 mm glass bulb type should be considered, as a minimum, .� , - 7
spray sprinklers designed for use in along with the corrosive nature of the t -
light, ordinary, or extra hazard, corn- chemical to which the sprinklers will be - -"'
-' ._r r
mercial occupancies such as banks, exposed.
hotels, shopping malls, factories, refin-
eries, chemical plants, etc. An intermediate level version of the
Series TY -B Pendent Sprinkler can be
The recessed version of the Series obtained by utilizing the Series TY -B,„
TY -B Pendent Sprinkler, where appli- Pendent Sprinkler in combination with
cable, is intended for use in areas with the Model S2 Shield.
a finished ceiling It uses a tw y
Style 10 (1/2 inch NPT) or Style 40 (3/4 WARNINGS i
inch NPT) Recessed Escutcheon. The The Series TY-B Sprinklers described f,,\
Recessed Escutcheon provides 1/2 herein must be installed and main- . ,
inch (12,7 mm) of recessed adjust- tained in compliance with this docu- -'
ment or up °'
�
p to 3/4 inch ( 19,1 mm ) of ment, as well as with the applicable .
total adjustment from the flush pen- standards of the National Fire Protec- _
dent position. The adjustment pro- tion Association, in addition to the . .a
vided by the Recessed Escutcheon re- standards of any other authorities hay- 0,, - 7.
duces the accuracy to which the fixed ing jurisdiction. Failure to do so may ',..:"
pipe drops to the sprinklers must be impair the performance of these de-
cut. vices.
Corrosion resistant coatings, where The owner is responsible for maintain -
applicable, are utilized to extend the ing their fire protection system and de-
life of copper alloy sprinklers beyond vices in proper operating condition.
that which would otherwise be ob- The installing contractor or sprinkler
tained when exposed to corrosive at- manufacturer should be contacted
mospheres. Although corrosion resis- with any questions.
tant coated sprinklers have passed the
standard corrosion tests of the appli- Model/Sprinkler
IMPORTANT Identification Y
Always refer to Technical Data c c
Sheet TFP700 for the "INSTALLER Numbers E
m
WARNING" that provides cautions m
with respect to handling and instal - TY1151 - Upright 2.8K, 1/2 "NPT 1-
lation of sprinkler systems and corn- TY1251 - Pendent 2.8K, 1/2 "NPT a
ponents. Improper handling and in- TY3151 - Upright 5.6K, 1/2 "NPT m
stallation can permanently damage TY3251 - Pendent 5.6K, 112 "NPT m
a sprinkler system or its compo- TY4151 - Upright 8.0K, 3/4 "NPT re
nents and cause the sprinkler to fail TY4251 - Pendent 8.0K, 314 "NPT o
to operate in a fire situation or cause TY4851 - Upright 8.0K, 112 "NPT l
it to operate prematurely. TY4951 - Pendent 8.0K, 1/2 "NPT o
Page 1 of 8 OCTOBER, 2005 TFP151
Page 2 of 8 TFP151
,
ESCUTCHEON 7/16" (11,1 mm)
PLATE SEATING 1/2" ** NOMINAL SSU
SURFACE NPT MAKE -IN DEFLECTOR
• .7 5
2 -1/4" f M 2 -3/16" 4
(57,2 mm) f o (55,6 mm) 2
1 -9/16" WRENCH I� .72L- 3
(39,7 mm) FLATS 1
SSP 7
DEFLECTOR CROSS
PENDENT UPRIGHT SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression 7 - Bushing orifice seat on frame.
Screw **Pipe thread connections per ISO 7/1 can be provided on
' special request.
FIGURE 1
STANDARD RESPONSE SERIES TY -B UPRIGHT (TY1151) AND PENDENT (TY1251) SPRINKLERS
2.8 K- FACTOR, 1/2 INCH NPT
ESCUTCHEON 7/16" (11,1 mm) STYLE 10
PLATE SEATING ** NOMINAL RECESSED
SURFACE NPT MAKE IN ESCUTCHEON DEFLECTOR
6
\-----=
�,,- 7/16" ` . : 5
2- 3/16" ___ -7 i•r � (11,1 mm)
(55,6 mm) k A. - NOMINAL 4
MAKE -IN
1 -1/2" iiiiii iiiiiiii►� `� 2-3/16" 941 2
(38,1 mm) U, I 1 (55,6 mm) r 11 f 3
i WRENCH = # 7 - �.��� r- - �11i= s -, FLATS - I
1
SSP DEFLECTOR 2 -7/8" (73,0 mm) DIA. — •- . 1 1/2" NPT
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame.
Screw ** Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 2
STANDARD RESPONSE SERIES TY-B UPRIGHT (TY3151) AND PENDENT (TY3251) SPRINKLERS
5.6 K- FACTOR, 1/2 INCH NPT
TFP151 Page 3 of 8
ESCUTCHEON 1/2" (12,7 mm) STYLE 40
PLATE SEATING ** NOMINAL RECESSED
- SURFACE 3!4" MAKE -IN ESCUTCHEON SSU
NPT DEFLECTOR
6
i r ' i r r% r''TT S *�
1.11 TT`
1/2" 7
2 -5/16" (12,7 mm)
(58,7 mm) 1 ig�_ i W 7 NOMINAL I i 4
` 01 ____ MAKE -IN
1 9/16" � �� lror� 2-1/4" 9 9 2
(39,7 mm) ' � I (57,2 mm) 3
I
1 __II__ - -- II ° WRENCH — -- - FLATS 1
SSP DEFLECTOR - 2 -7 /8° (73,0 mm) DIA. —1 3/4" NPT ** f
PENDENT RECESSED PENDENT UPRIGHT CROSS SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression 7 - Ejection orifice seat on frame.
Screw Spring ** Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 3
STANDARD RESPONSE SERIES TY-B UPRIGHT (TY4151) AND PENDENT (TY4251) SPRINKLERS
8.0 K- FACTOR, 3/4 INCH NPT
ESCUTCHEON 7/16" (11,1 mm)
PLATE SEATING 1/2" ** NOMINAL SSU
SURFACE NPT MAKE -IN DEFLECTOR
* 6
-- tri \ Tn 44
111 '• 5
2 -1/4" G
2-3/16"
(57,2 mm) � � = �
(55,6 mm) ' I I
t" 4
2
1 -9/16 WRENCH � 1 1� 4'
(39,7 mm) FLATS � � 7 4 ■ 0
SSP
DEFLECTOR CROSS
PENDENT UPRIGHT SECTION
1 - Frame 3 - Sealing 4 - Bulb 6 - Deflector * Temperature rating is indicated on deflector or adjacent to
2 - Button Assembly 5 - Compression orifice seat on frame.
Screw ** Pipe thread connections per ISO 7/1 can be provided on
special request.
FIGURE 4
STANDARD RESPONSE SERIES TY-B UPRIGHT (TY4851) AND PENDENT (TY4951) SPRINKLERS
8.0 K- FACTOR, 1/2 INCH NPT
Page 4 of 8 TFP151
SPRINKLER FINISH (See Note 8)
K TYPE TEMP. BULB NATURAL CHROME WHITE"' LEAD WAX WAX OVER
LIQUID BRASS PLATED POLYESTER COATED COATED LEAD COATED
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
2.8 (TY1251) 1, 2, 3 N/A
1/2" and 175 °F /79 °C Yellow
NPT UPRIGHT 200 °F /93 °C Green
(TY1151)
286 °F /141 °C Blue
360 °F /182 °C Mauve 1, 2
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
(TY3251) 1, 2, 3, 4, 5, 6, 7 1,2,3,5 1,2,3,5 1,2,3,5
and 175 °F /79 °C Yellow
UPRIGHT 200 °F /93 °C Green
5.6 (TY3151)
286 °F /141 °C Blue 1 ",2 ", 3 ", 5" T 1 ", 2••, 3`•, 5"
1/2"
NPT 360 °F /182 °C Mauve N/A
135 °F /57 °C Orange
RECESSED 155 °F /68 °C Red
PENDENT 1, 2, 3, 4, 5 1, 2, 4, 5 N/A
(TY3251)' 175 °F /79 °C Yellow
Figure 4 200 °F /93 °C Green
286 °F /141 °C Blue 1, 2
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
(TY4251) 1,2,5 1,2,3,5 1,2,5
and 175 °F /79 °C Yellow 1, 2, 3, 4, 5, 6, 7
8.0 UPRIGHT 200 °F /93 °C Green
3/4" (TY4151) -
286 °F/141 °C Blue 1 ",2 ", 3•`, 5" 1", 2 ", 5**
NPT
360 °F /182 °C Mauve ( N/A
135 °F /57 °C Orange
RECESSED 155 °F /68 °C Red
PENDENT 1, 2, 3, 4, 5 N/A
(TY4251)' 175 °F /79 °C Yellow
Figure 5 200 °F /93 °C Green
286 °F /141 °C Blue 1, 2
135 °F /57 °C Orange
PENDENT 155 °F /68 °C Red
8.0 (TY4951)
1/2" and 175 °F /79 °C Yellow 1, 2, 3, 5 N/A
NPT UPRIGHT 200 °F /93 °C Green
(TY4851)
286 °F /141 °C Blue
360 °F /182 °C Mauve
NOTES:
1. Listed by Underwriters Laboratories, Inc. (UL).
2. Listed by Underwriters Laboratories, Inc. for use in Canada (C -UL).
3. Approved by Factory Mutual Research Corporation (FM).
4. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 007k/03).
5. Approved by the City of New York under MEA 354-01 -E.
6. VdS Approved (For details contact Tyco Fire & Building Products, Enschede, Netherlands, Tel. 31- 53- 428- 4444/Fax 31 -53 -428- 3377).
7. Approved by the Loss Prevention Certification Board (LPCB Ref. No. 094a/05).
8. Where Polyester Coated, Lead Coated, Wax Coated, and Wax over Lead Coated Sprinklers are noted to be UL and C -UL Listed, the
sprinklers are UL and C -UL Listed as Corrosion Resistant Sprinklers. Where Lead Coated, Wax Coated, and Wax over Lead Coated
Sprinklers are noted to be FM Approved, the sprinklers are FM Approved as Corrosion Resistant Sprinklers.
• Installed with Style 10 (1/2" NPT) or Style 40 (3/4" NPT) 3/4" Total Adjustment Recessed Escutcheon, as applicable.
" 150 °F /66 °C Maximum Ceiling Temperature.
•" Frame and deflector only. Listings and approvals apply to color (Special Order).
N /A: Not Available
TABLE A, LABORATORY LISTINGS AND APPROVALS
TFP151 Page 5 of 8
2 -7/8" DIA. L,
(73,0 mm)
5/8±1/4" 3/4" (19,1 mm)
(15,9±6,4 mm) 2 -1 /4" DIA. 1/4" (6,4 mm) WRENCH RECESS
(END "A" USED FOR
FACE OF (57,2 mm) MOUNTING �. 1/2 NPT MODELS)
SPRINKLER PLATE
FITTING
1/8" WRENCH RECESS
(3,2 mm) (END "B" USED FOR
3/4" NPT MODELS)
i I i ijl J FIGURE 7
W -TYPE 6 SPRINKLER
WRENCH
MOUNTING
SURFACE
WRENCH
CLOSURE SERIES 1 -1/4" (31,8 mm) RECESS
TY-B 3/4" (19,1 mm)
FIGURE 5
SERIES TY-B RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT �,
STYLE 10 RECESSED ESCUTCHEON
5.6 K- FACTOR, 1/2 INCH NPT % ` e �
PUSH WRENCH
IN TO ENSURE
2 - 7/8" DIA. ENGAGEMENT
(73,0 mm) 3/4" (19,1 mm) WITH SPRINKLER
5/8±1/4" WRENCHING AREA
(15,9±6,4 mm) 2 -1/4" DIA. 1/4" (6,4 mm)
(57,2 mm) FIGURE 8
FACE OF MOUNTING W -TYPE 7 RECESSED
SPRINKLER PLATE SPRINKLER WRENCH
FITTING
1/8"
III (3,2 mm)
11
1,14 r
MOUNTING
SURFACE •
CLOSURE SERIES 1 -5/16" (33,3 mm)
TY 13/16" (20,6 mm)
FIGURE 6
SERIES TY-B RECESSED PENDENT SPRINKLER ASSEMBLY
WITH TWO -PIECE 3/4 INCH TOTAL ADJUSTMENT
STYLE 40 RECESSED ESCUTCHEON
8.0 K- FACTOR, 3/4 INCH NPT
Page 6 of 8 TFP151
ing the wax coating. Before wrench
Technical Installation tightening the sprinkler, the jaws of the
wrench are to be adjusted to just con -
D ata The Series TY -B Sprinklers must be tact the sprinkler wrench flats. After
installed in accordance with the follow- wrench tightening the sprinkler, loosen
Approvals ing instructions: the wrench jaws before removing the
UL and C -UL Listed. wrench.
FM, LPCB, VdS, and NYC Approved. NOTES
(Refer to Table A for complete ap- Do not install any bulb type sprinkler if After installation, the sprinkler wrench
proval information including corrosion the bulb is cracked or there is a loss of flats and frame arms must be in-
resistant status.) liquid from the bulb. With the sprinkler spected and the wax coating re-
held horizontally, a small air bubble touched (repaired) whenever the coat -
Maximum Working Pressure should be present. The diameter of the
ing has been damaged and bare metal
175 psi (12,1 bar) air bubble is approximately 1/16 inch is exposed. The wax coating on the
Discharge Coefficient (1,6 mm) for the 135 °F /57 °C to 3/32 wrench flats can be retouched by gen-
K = 2.8 GPM /psilI (40,3 LPM /bar inch (2,4 mm) for the 360 °F /182 °C tly applying a heated 1/8 inch diameter
K = 5.6 GPM /psili (80,6 LPM /bar / temperature ratings. steel rod to the areas of wax that have
K = 8.0 GPM /psi - la (115,2 LPM/bar1/2) been damaged, to smooth it back over
A leak tight 1/2 inch NPT sprinkler joint areas where bare metal is exposed.
Temperature Ratings should be obtained with a torque of 7
Refer to Table A to 14 ft.lbs. (9,5 to 19,0 Nm). A maxi- NOTES
Finishes mum of 21 ft. lbs. (28,5 Nm) of torque Only retouching of the wax coating ap-
Sprinkler: Reessed Escutcheon: may be used to install sprinklers with plied to the wrench flats and frame
White Coated, Chrome Plated, or 1/2 NPT connections. A leak tight 3/4 arms is permitted, and the retouching
Brass Plated inch NPT sprinkler joint should be ob- is to be performed only at the time of
. tained with a torque of 10 to 20 ft.lbs. the initial sprinkler installation.
Physical Characteristics (13,4 t 0 26,8 Nm). A maximum of 30 The steel rod should be heated only to
Frame Bronze ft.lbs. 4,7 Nm) of torque is to be used the point at which it can begin to melt
Button Brass /Copper to install sprinklers with 3/4 NPT con- the wax, and appropriate precautions
Sealing Assembly nections. Higher levels of torque may need to be taken, when handling the
Beryllium Nickel w/Teflont distort the sprinkler heated rod, in order to prevent the
rinkler inlet and cause
Bulb Glass leakage or impairment of the sprinkler. install eat e er from nei r e t o p
Compression Screw Bronze Do not attempt to make -up for insuf-
Deflector Copper cient adjustment in the escutcheon If attempts to retouch the wax coating
Bushing (K =2.8) Bronze plate by under- or over- tightening the with complete coverage are unsuc-
sprinkler. Readjust the position of the cessful, additional wax can be ordered
sprinkler fitting to suit. in the form of a wax stick (the end of
which is color coded). Only the correct
Operation The Series TY -B Pendent and Up- color coded wax is to be used, and
The glass Bulb contains a fluid which right Sprinklers must be installed in retouching of wrench flats and frame
9 accordance with the following instruc- arms is only permitted at the time of
expands when exposed to heat. When tions. initial sprinkler installation. With the
the rated temperature is reached, the steel rod heated as previously de-
fluid expands sufficiently to shatter the Step 1. Pendent sprinklers are to be scribed, touch the rod to the area re-
glass Bulb, allowing the sprinkler to installed in the pendent position, and
activate and water to flow. upright sprinklers are to be installed in quiring additional wax with the rod an-
the upright position. gled downward, and then touch the
wax stick to the rod approximately
Design Step 2. With pipe thread sealant ap - one -half inch away from the area re-
plied to the pipe threads, hand tighten quiring retouching. The wax will melt
C riteria the sprinkler into the sprinkler fitting. and run down onto the sprinkler.
Step 3. Tighten the sprinkler into the
The Series TY -B Pendent and Upright sprinkler fitting using only the W -Type The Series TY -B Recessed Pendent
Sprinklers are intended for fire protec- 6 Sprinkler Wrench (Ref. Figure 7), Sprinklers must be installed in ac-
tion systems designed in accordance except that an 8 or 10 inch adjustable cordance with the following instruc-
with the standard installation rules rec- Crescent wrench is to be used for wax bons.
ognized Step A. After installing the Style 10 or
. p e
ed by the applicable Listing or coated sprinklers. With reference to
Approval agency (e.g., UL Listing is Figures 1, 2, 3, and 4 the W -Type 7 St p A. Af Plate, as applicable, 10 or
- based on the requirements of NFPA Sprinkler Wrench or the adjustable Mountin
13, and FM Approval is based on the Crescent wrench, as applicable is to the sprinkler threads and with pipe
requirements of FM's Loss Prevention be applied to the wrench flats. thread sealant applied to the pipe
Data Sheets). Only the Style 10 or 40 threads, hand tighten the sprinkler into
Recessed Escutcheon, as applicable When installing wax coated sprinklers the sprinkler fitting.
,
is to be used for recessed pendent with the adjustable Crescent wrench,
installations. additional care needs to be exercised Step B. Tighten the sprinkler into the
to prevent damage to the wax coating sprinkler fitting using only the W -Type
on the sprinkler wrench flats or frame 7 Recessed Sprinkler Wrench (Ref.
arms and, consequently, exposure of Figure 8). With reference to Figure 3
bare metal to the corrosive environ- or 4, the W -Type 7 Recessed Sprinkler
ment. The jaws of the wrench should Wrench is to be applied to the sprinkler
be opened sufficiently wide to pass wrench flats.
over the wrench flats without damag- Step C. After the ceiling has been in-
L
TFP151 Page 7 of 8
stalled or the finish coat has been ap- The owner is responsible for the in-
plied, slide on the Style 10 or 40 Clo- spection, testing, and maintenance of L imited
sure over the Series TY -B Sprinkler their fire protection system and de-
and push the Closure over the Mount- vices in compliance with this docu- W arrant
ing Plate until its flange comes in con- ment, as well as with the applicable
tact with the ceiling. standards of the National Fire Protec- Products manufactured by Tyco Fire &
tion Association (e.g., NFPA 25), in Building Products are warranted solely
Care and addition to the standards of any other to the original Buyer for ten (10) years
authorities having jurisdiction. The in- against defects in material and work -
stalling contractor or sprinkler manu- manship when paid for and properly
Maintenance facturer should be contacted relative installed and maintained under normal
The Series TY -B Sprinklers must be to any questions. use and service. This warranty will ex-
P pire ten (10) years from date of ship -
maintained and serviced in accord- It is recommended that automatic ment by Tyco Fire & Building Products.
ance with the following instructions: sprinkler systems be inspected, No warranty is given for products or
tested, and maintained by a qualified components manufactured by compa-
NOTES Inspection Service in accordance with Hies not affiliated by ownership with
Before closing a fire protection system local requirements and /or national Tyco Fire & Building Products or for
main control valve for maintenance codes. products and components which have
work on the fire protection system that been subject to misuse, improper in-
it controls, permission to shut down the stallation, corrosion, or which have not
affected fire protection system must be been installed, maintained, modified
obtained from the proper authorities or repaired in accordance with applica-
and all personnel who may be affected ble Standards of the National Fire Pro -
by this action must be notified. tection Association, and /or the stand -
Absence of an escutcheon, which is aids of any other Authorities Having
used to cover a clearance hole, may Jurisdiction. Materials found by Tyco
delay the time to sprinkler operation in Fire & Building Products to be defec-
• afire situation. tive shall be either repaired or re-
placed, at Tyco Fire & Building Prod -
Sprinklers that are found to be leaking ucts' sole option. Tyco Fire & Building
or exhibiting visible signs of corrosion Products neither assumes, nor author -
must be replaced. izes any person to assume for it, any
Automatic sprinklers must never be other obligation in connection with the
painted, plated, coated or otherwise sale of products or parts of products.
altered after leaving the factory. Modi- Tyco Fire & Building Products shall not
Pied sprinklers must be replaced. be responsible for sprinkler system de-
Sprinklers that have been exposed to sign errors or inaccurate or incomplete
corrosive products of combustion, but information supplied by Buyer or
have not operated, should be replaced Buyer's representatives.
if they cannot be completely cleaned IN NO EVENT SHALL TYCO FIRE &
by wiping the sprinkler with a cloth or BUILDING PRODUCTS BE LIABLE,
by brushing it with a soft bristle brush. IN CONTRACT, TORT, STRICT LI-
Care must be exercised to avoid dam - ABILITY OR UNDER ANY OTHER
age to the sprinklers - before, during, LEGAL THEORY, FOR INCIDENTAL,
and after installation. Sprinklers dam- INDIRECT, SPECIAL OR CONSE-
aged by dropping, striking, wrench QUENTIAL DAMAGES, INCLUDING
twist/slippage, or the like, must be re- BUT NOT LIMITED TO LABOR
placed. Also, replace any sprinkler that CHARGES, REGARDLESS OF
has a cracked bulb or that has lost WHETHER TYCO FIRE & BUILDING
liquid from its bulb. (Ref. Installation PRODUCTS WAS INFORMED
Section). ABOUT THE POSSIBILITY OF SUCH
DAMAGES, AND IN NO EVENT
Frequent visual inspections are rec- SHALL TYCO FIRE & BUILDING
ommended to be initially performed for PRODUCTS' LIABILITY EXCEED AN
corrosion resistant coated sprinklers, AMOUNT EQUAL TO THE SALES
after the installation has been corn- PRICE.
pleted, to verify the integrity of the cor- THE FOREGOING WARRANTY IS
rosion resistant coating. Thereafter,
annual inspections per NFPA 25 MADE /N LIEU OF ANY AND ALL
should suffice; however, instead of in OTHER WARRANTIES EXPRESS
specting from the floor level, a random OR IMPLIED, INCLUDING WARRAN-
sampling of close -up visual inspec- TIES OF MERCHANTABILITY AND
tions should be made, so as to better FITNESS FORA PARTICULAR PUR-
determine the exact sprinkler condi- POSE,
tion and the long term integrity of the
corrosion resistant coating, as it may
be affected by the corrosive conditions
present.
Page 8 of 8 TFP151
P/N 57- XXX -X -XXX
I I
SPRINKLER TEMPERATURE
MODEUSIN RATING
530 2.8K UPRIGHT (1/2 "NPT) TY1151 1 NATURAL BRASS 135 135 °F /57 °C
531 2.8K PENDENT (1/2 "NPT) TY1251 4 WHITE POLYESTER 155 155 °F /68 °C
570 5.6K UPRIGHT (1/2 "NPT) TY3151 3 WHITE (RAL9010)* 175 175 °F/79 °C
571 5.6K PENDENT (1/2 "NPT) TY3251 9 CHROME PLATED 200 200 °F /93 °C
590 8.0K UPRIGHT (3/4 "NPT) TY4151 7 LEAD COATED 286 286 °F /141 °C
591 8.0K PENDENT (3/4 °NPT) TY4251 6 WAX COATED 360 360 °F /182 °C
286 °F /141 °C MAX.
560 8.0K UPRIGHT (1/2 °NPT) TY4851
8 WAX OVER LEAD
561 8.0K PENDENT (1/2 "NPT) TY4951 286 °F /141 °C MAX.
Eastern Hemisphere sales only.
TABLE B
PART NUMBER SELECTION
SERIES TY-B PENDENT AND UPRIGHT SPRINKLERS
Recessed Escutcheon: Wax Sticks:
Ordering Specify: Style (specify) Recessed Es- (for retouching wrench damaged
cutcheon with (specify finish), P/N wax coating)
Procedur (specify). Specify: (Specify color) color coded
When placing an order, indicate the full 1/2" (15 mm) Wax Stick for retouching (specify tern -
product name. Refer to the Price List Style 10 perature rating) temperature rated Se-
for complete listing of Part Numbers. 1/2° Chrome ( 15 mm Plated ) P/N 56-701 -9-010 ries TY -B Sprinklers, P/N (specify).
Contact your local distributor for avail- Style 10 Black for 135 °F P/N 56 -065 -1 -135
ability. White Colo Red for 155 °F P/N 56 -065 -1 -155
Coated P/N 56-701-4-010 Yellow for 175 °F P/N 56 -065-1 -175
Sprinkler Assemblies with NPT 1/2 y o) 91u for 200°F and
Thread Connections: White RAL9010" P/N 56- 701 -3-010 286°F P/N 56-065-1-286
Specify: (Specify Model /SIN), Stand- 1/2° (15 mm)
NOTES
and Response, (specify K- factor), Brass Plated P/N 56- 701 -2 -010 Each wax stick is suitable for retouch -
(specify temperature rating), Series 3/4° (20 mm) ing up to twenty-five sprinklers.
TY -B (specify Pendent or Upright) Style 40
Sprinkler with (specify type of finish or Chrome Plated P/N 56- 700 -9-010 The wax used for 286 °F sprinklers is
coating), P/N (specify from Table B). 3/4" (20 mm) the same as for 200 °F sprinklers, and,
Style 40 therefore, the 286 °Fsprinkler is limited
White Color
Coated P/N 56-700-4-010 to the same maximum ceiling tempera -
3/4° (20 mm) ture as the 200 °F sprinkler (i.e.,
Style 40 150 °F).
White RAL9010° P/N 56- 700 -3-010
3/4" (20 mm)
Style 40
Brass Plated P/N 56- 700 -2 -010
• Eastern Hemisphere sales only.
Sprinkler Wrench:
Specify: W -Type 6 Sprinkler Wrench,
P/N 56 -000 -6 -387.
Specify: W -Type 7 Sprinkler Wrench,
P/N 56 -850 -4 -001.
TYCO FIRE & BUILDING PRODUCTS, 451 North Cannon Avenue, Lansdale, Pennsylvania 19446