Plans MI 7 kLt - D-oo g - co O a_,-
I
tqccs / Fire & Building
Products
Technical Services: Tel: (800) 381 -9312 / Fax: (800) 791 -5500
Series TY -B — 2.8, 5.6, and 8.0 K- factor
Upright, Pendent, and Recessed Pendent Sprinklers
Standard Response, Standard Coverage
General cable approval agencies, the testing is
not representative of all possible cor-
rosive atmospheres. Consequently, it ?,t
D escription is recommended that the end user be ,.�.,� Via ;f" > 3.
consulted with respect to the suitability :, ;` ;?'«\'
The Series TY -B, 2.8, 5.6, and 8.0 of these coatings for any given corro- " � ) if K- factor, Upright and Pendent Sprin- sive environment. The effects of ambi-
klers described in this data sheet are ent temperature, concentration of ',, <»;
standard response - standard cover- chemicals, and gas /chemical velocity, , , - �_.: �P,'a
age, decorative 5 mm glass bulb type should be considered, as a minimum, 4 „, a ,
spray sprinklers designed for use in along with the corrosive nature of the � . , , � �' T
light, ordinary, or extra hazard, corn- chemical to which the sprinklers will be '_ - ,A,
mercial occupancies such as banks, exposed. w ° „ `` � ° =' °#
_.3 hotels, shopping malls, factories, refin-
eries, chemical plants, etc. An intermediate level version of the
Series TY -B Pendent Sprinkler can be
The recessed version of the Series obtained by utilizing the Series TY -B
TY -B Pendent Sprinkler, where appli- Pendent Sprinkler in combination with
cable, is intended for use in areas with the Model S2 Shield.
a finished ceiling. It uses a two- piece e` e
Style 10 (1/2 inch NPT) or Style 40 (3/4 WARNINGS 4 e `
inch NPT) Recessed Escutcheon. The The Series TY-B Sprinklers described E '
Recessed Escutcheon provides 1/2 herein must be installed and main -
inch (12,7 mm) of recessed adjust- tained in compliance with this docu- _ - j
5
ment or up to 3/4 inch (19,1 mm) of ment, as well as with the applicable "
total adjustment from the flush pen- standards of the National Fire Protec -
dent position. The adjustment pro- tion Association, in addition to the '2. .
vided by the Recessed Escutcheon re- standards of any other authorities hay -
duces the accuracy to which the fixed ing jurisdiction. Failure to do so may , *,,,„ - 31'
pipe drops to the sprinklers must be impair the performance of these de-
cut. vices.
Corrosion resistant coatings, where The owner is responsible for maintain-
applicable, are utilized to extend the ing their fire protection system and de-
life of copper alloy sprinklers beyond vices in proper operating condition.
that which would otherwise be ob- The installing contractor or sprinkler
tained when exposed to corrosive at- manufacturer should be contacted
mospheres. Although corrosion resis- with any questions.
tant coated sprinklers have passed the
standard corrosion tests of the appli-
Model/Sprinkler
IMPORTANT Identification
Always refer to Technical Data �®
Sheet TFP700 for the "INSTALLER Numbers
WARNING” that provides cautions
with respect to handling and instal- TY1151 - Upright 2.8K, 1/2 "NPT
lation of sprinkler systems and com- TY1251 - Pendent 2.8K, 1/2"NPT
ponents. Improper handling and in- TY3151 - Upright 5.6K, 1/2 "NPT
stallation can permanently damage TY3251 - Pendent 5.6K, 1/2 "NPT
a sprinkler system or its compo- TY4151 - Upright 8.0K, 3/4"NPT
nents and cause the sprinkler to fail TY4251 - Pendent 8.0K, 3/4 "NPT
to operate in a fire situation or cause TY4851 - Upright 8.0K, 1/2 "NPT
it to operate prematurely. TY4951 - Pendent 8.0K, 1/2 "NPT
Page 1 of 8 DECEMBER, 2007 TFP151
TFP151 Page 5 of 8
SPRINKLER FINISH
K TYPE NATURAL CHROME WHITE LEAD WAX WAX OVER
BRASS PLATED POLYESTER COATED COATED LEAD COATED
2.8 PENDENT (TY1251)
1/2" and 175 PSI (12,1 BAR) N/A
NPT UPRIGHT (TY1151)
PENDENT (TY3251)
5.6 and 250 PSI (17,2 BAR) 175 PSI (12,1 BAR)
• 1/2" UPRIGHT (TY3151) OR
NPT 175 PSI (12,1 BAR)
RECESSED PENDENT
(TY3251) (SEE NOTE 1) N/A
8.0 PENDENT (TY4251)
3/4" and 175 PSI (12,1 BAR)
NPT UPRIGHT (TY4151)
RECESSED PENDENT
(TY4251) 175 PSI (12,1 BAR) N/A
8.0 PENDENT (TY4951)
1/2" and 175 PSI (12,1 BAR)
NPT UPRIGHT (TY4851)
NOTE:
1. The maximum working pressure of 250 psi (17,2 bar) only applies to the Listing by Underwriters Laboratories, Inc. (UL); the Listing by
Underwriters Laboratories, Inc. for use in Canada (C -UL); and, the Approval by the City of New York.
TABLE B, MAXIMUM WORKING PRESSURE
Technical Operation
Data The glass Bulb contains a fluid which
expands when exposed to heat. When
Approvals the rated temperature is reached, the
UL and C -UL Listed. fluid expands sufficiently to shatter the
FM, LPCB, VdS, and NYC Approved. glass Bulb, allowing the sprinkler to
(Refer to Table A for complete ap- activate and water to flow.
proval information including corrosion
resistant status.) Design
Maximum Working Pressure /�
Refer to Table B. Criteria
Discharge Coefficient
K = 2.8 GPM /psi (40,3 LPM /bar1 /2) The Series TY -B Pendent and Upright
K = 5.6 GPM /psi (80,6 LPM /bar112) Sprinklers are intended for fire protec-
K = 8.0 GPM /psi (115,2 LPM /bar1 /22) tion systems designed in accordance
with the standard installation rules rec-
Temperature Ratings ognized by the applicable Listing or
Refer to Table A. Approval agency (e.g., UL Listing is
Finishes based on the requirements of NFPA
Sprinkler: Refer to Table A. 13, and FM Approval is based on the
Recessed Escutcheon: White Coated, requirements of FM's Loss Prevention
Chrome Plated, or Brass Plated. Data Sheets). Only the Style 10 or 40
Recessed Escutcheon, as applicable,
Physical Characteristics is to be used for recessed pendent
Frame Bronze installations.
Button Brass /Copper a
Sealing Assembly a�
Beryllium Nickel w /Teflont m
Bulb Glass
Compression Screw Bronze
Deflector Copper a
Bushing (K =2.8) Bronze
.- . ScheduI
Fully Listed and FM Approved Sprinkler Pipe
When you specify Schedule -10 /Schedule -40 sprinkler pipe you get a UL listed and FM approved product. Although these
products do not require separate approvals, Schedule -10 /Schedule -40 gives you the extra quality assurance you demand.
Our Sch -10 (1' / "- 8 ") pipe and Sch -40 (I"- 2''4 ") pipe have passed the same thorough lab testing as our other listed pipe
products, and receive periodic mill inspections from both UL and FM agents to ensure consistent quality.
Galvanized Pipe Sch -40 Sp .
NPS Nominal I.D. Wt. Wt. (H20 Filled) Pcs/ WI/Lift (21') Wt/Lift (24') WI/Litt (25')
Schedule-10/Schedule-40 product can be In; mm In: mm Lbs /Ft; Kg /m Lbs/Ft; Kg /m Lift Lbs; Kg Lbs; Kg Lbs; Kg
"hot -dip" galvanized to meet FM
requirements for dry systems in 1" 1.049 1.680 2.05 70 2,470 2,822 2,940
accordance with the zinc coating 25 26.6 2.5 3.05 70 1,120 1,280 1,334
specifications of ASTM A -123. 11/4' 1.380 2.270 2.93 51 2,431 2,778 2,894
32 35.1 4.36 4.36 51 1,103 1,260 1,313
Superior Coating 1W 1.610 2.720 3.61 44 2,513 2,872 2,992
40 40.9 4.0 5.37 44 1,140 1,303 1,357
Our advanced formula mill coating of- 2" 2.067 3.650 5.13 30 2,300 2,628 2,738
fers a clean, durable surface, It is also 50 52.5 5.4 7.63 30 1,043 1,192 1,242
paint -ready for custom color applications
2W 2,469 5.790 7.86 19 2,310 2,640 2,750
without special preparation. 65 62.7 8.6 11.73 19 1,048 1,197 1,247
The internal surface of all black Allied
Tube & Conduit Fire Sprinkler pipe
products up to 4.5000" in diameter is SCh -10 Specifications
coated with our new Antibacterial For- NPS Nominal I.D. Wt. Wt. (H20 Filled) Pcs/ Wt/Lift (21') WI/Litt (24') Wt/Lift (25')
mula, "ABF ". In scientific laboratory In; mm In; mm Lbs /Ft; Kg /m Lbs/Ft; Kg /m Lift Lbs; Kg Lbs; Kg Lbs; Kg
test, ABS proved to have superior resis- 1" 1.097 1.400 1.81 91 2,675 3,053 3,185
tance to microbial colonization of pipe 25 27.9 2.1 2.70 91 1,213 1,385 1,445
walls, thereby delaying or possibly pre- 11/4" 1.442 1.810 2.52 61 2,319 2,664 2,760
venting the onset of Microbiologically 32 36.6 2.7 3.75 61 1,052 1,208 1,252
Influenced corrosion (MIC) when the 11/2' 1.682 2.080 3.04 61 2,664 3,045 3,172
First Sprinkler System is first installed. 40 42.7 3.1 4.52 61 1,208 1,381 1,439
American Made ` 72 2'157. - ?;.--'; - 4.22 - 37..,.:205i • - - :. 2 ;344 - , _ 2;442 - -~ ;:- . ..
50 54.8 3.9 6.28 37 930 1,063 1,108
Meets `Buy American" requirement 21/2° 2.635 3.530 5.89 30 2,224 2,542 2,648
and is available through distributors in 65 66.9 5.3 8.77 30 1,009 1,153 1,201
the USA, Canada and Mexico. 3" 3.260 4.330 7.94 19 1,728 1,975 2,057
Specifications' & App 80 82.8 6.4 11.82 19 784 896 933
4" 4.260 5.610 11.78 19 2,238 2,558 2,665
Schedule -10 /Schedule -40 pipe are in 90 108.2 8.3 17.53 19 1,015 1,160 1,209
compliance with the following: 5" 5.295 7.77 17.33 10 1,632 1,865 1,943
125 134.5 11.56 25.80 10 740 846 881
ASTM A -135, and NFPA 13. Both pipe 6" 6.357 9.290 23.03 10 1,951 2,230 2,322
products have a working pressure rating 150 161.5 13.8 34.27 10 885 1,012 1,053
of 300 psi maximum and also meet the 8" 8.249 16.490 40.15 7 2,424 2,770 2,885
stringent requirement for the following 200 209.5 24.5 59.75 7 1,100 1,256 1,309
tests:
• Welded Outlets el 41t• 0
• Hydrostatic Pressure Listed Approved Listed
• Side Wall Rupture
• Vibration Test
��� ® /F /ow Conrro/ 16100 S. Lathrop • Harvey, IL 60426 Customer Service:
aIIi®d 11350 Norcom Rd. • Philadelphia, PA 19154 (800) 882 -5543
TUBE 8 CONDUIT 2525 N. 27 th Ave. • Phoenix, AZ 85009 Fax 708 - 339 -1806
S5 - 3