Permit CITY OF TIGARD ELECTRICAL PERMIT
111 Permit #: ELC2010 -00615
1 8 : C OMMUNITY DEVELOPMENT Da te Issued: 11/02/2010
TIGARD 13125 SW Hall Blvd., Tigard OR 97223 503.718.2439 Parcel: 151260000300
Jurisdiction: TIGARD
Site address: 9524 SW WASHINGTON SQUARE RD H08
Project: H & M Subdivision: WASHINGTON SQUARE MALL Lot: 0
Project Description: Electrical for TI. 1/12/2011: Reprinted for additional fees paid.
Contractor: RIVIERA ELECTRIC LLC Owner: PPR WASHINGTON SQUARE LLC
7312 NE PAR LN 2235 FARADAY AVE STE #0
VANCOUVER, WA 98662 CARLSBAD, CA 92008
PHONE:
PHONE: 503 - 740 -2291
FAX: 360- 230 -2330
FEES
Quantity Description Date Amount
6 ea Services or Feeders - 200 11/02/2010 $604.20
Specifics: amps or less
128 crt Branch Circuits w /Purchase 11/02/2010 $949.76
Type of Use: COM Service or Feeder
Class of Work: ALT 1 ea 12% State Surcharge - 11/02/2010 $186.48
Electrical
Type of Const: 1 ea Services or Feeders - 601 to 01/12/2011 $301.04
Occupancy Grp: 1000 amps
0 ea 12% State Surcharge - 01/12/2011 $36.12
Electrical
1 ea Plan Review Electricial 01/12/2011 $463.75
Total $2,541.35
i
Required Items and Reports (Conditions)
This permit is issued subject to the regulations contained in the Tigard Municipal Code, State of OR. Specialty Codes and all other applicable law. All work will
be done in accordance with approved plans. This permit will expire if work is not started within 180 days of issuance, or if work is suspended for more the 180
days. ATTENTION: Oregon law requires you to follow the rules adopted by the Oregon Utility Notification Center. Those rules are set forth in OAR
952- 001 -0010 throw s R,. -00'0. You may obtain a copy of the rules or direct questions to OUNC by calling 503.232.19877 or 1.800.332.2344.
Issued By: 1 A Permittee Signature: ew ,
OWNER INSTALLATION ONLY
The installation is being made on property I own which is not intended for sale, lease or rent.
OWNER'S SIGNATURE Date:
CONTRACTOR INSTALLATION ONLY
SIGNATURE OF SUPR. ELEC' Date:
LICENSE NO.
Call 503.639.4175 by 7:00 a.m. for the next available inspection date.
This permit card shall be kept in a conspicuous place on the job site until completion of the project
Approved plans are required on the job site at the time of each inspection.
a CITY OF TIGARD ELECTRICAL PERMIT
.114 o COMMUNITY DEVELOPMENT Permit #: ELC2010 00615
T [GA R D 13125 SW Hall Blvd., Tigard OR 97223 503.639.4171 Date Issued: 11/02/2010
Parcel: 1S1260000300
Jurisdiction: TIGARD
Site address: 9524 SW WASHINGTON SQUARE RD H08
Subdivision: WASHINGTON SQUARE MALL Lot: 0
Project: H & M
Project Description: Electrical for TI.
Owner: FEES
PPR WASHINGTON SQUARE LLC Quantity Description Date Amount
2235 FARADAY AVE STE #O
CARLSBAD, CA 92008 6 ea Services or Feeders - 200 11/02/2010 $604.20
amps or less
PHONE: 128 crt Branch Circuits w /Purchase 11/02/2010 $949.76
Service or Feeder
1 ea 12% State Surcharge - 11/02/2010 $186.48
Contractor: Electrical
RIVIERA ELECTRIC LLC
7312 NE PAR LN
VANCOUVER, WA 98662
PHONE: 503 - 740 -2291
FAX: 360 - 230 -2330
Type of Use: COM
Class of Work: ALT Type of Const:
Occupancy Grp:
Total $1,740.44
Required Items and Reports (Conditions)
This permit is issued subject to the regulations contained in the Tigard Municipal Code, State of OR. Specialty Codes and all other applicable law. All work will
be done in accordance with approved plans. This permit will expire if work is not started within 180 days of issuance, or if work is suspended for more the 180
days. ATTENTION: Oregon law requires you to fo • - . - -opted by the Oregon Utility Notification Center. Thos rules are set forth in OAR
952 - 001 -0010 through OAR 952- 001 -0100. You may obtai - copy of the rules • direct questions to OUNC by calling 503 46.6 9 or 1.800. 2 344.
r
..
Issued By: i _ ��: , 7-4! Permittee Signature:
OWNER INSTALLATION ONLY
The installation is being made on property I own which is not intended for sale, lease or rent.
OWNER'S SIGNATURE Date:
CONTRACTOR INSTALLATION ONLY
SIGNATURE OF SUPR. ELEC' Date:
LICENSE NO.
Call 503.639.4175 by 7:00 a.m. for an inspection that business day.
This permit card shall be kept in a conspicuous place on the job site until completion of the project
Approved plans are required on the Job site at the time of each inspection.
Electrical Permit Application 0 FoR orr►cSI. : ()Nix
City of Tigard �� ►: IJ
et4 \Q Received
� 1. Date/B : f ,�
° 13125 SW Hall Blvd., Tigard, OR 97
1 Phone: 503.639.4171 Fax: 503.598.1960 . \ G ,�:. Other Permit: 11 +,A (0- 1P 1Q 36
I. I t i A I: I > Inspection Line: 503.639.4175 1 0 . , Da Ready/By: • l w See Page 2 for
Internet: www.tigard- or.gov �` Notified/Method: ^TC.`Y Supplemental Information
TYPE OF WORK p 0 ,1.. PLAN REVIEW
E New co El Addition /alteration/rP"placement Please check all that apply (submit 2 sets of plans w /items checked below):
❑ Service or feeder 400 amps or more ❑ Building over three stories.
❑ Demolition ❑ Other: where the available fault current ❑ Marinas and boatyards.
CATEGORY OF CONSTRUCTION exceeds 10,000 amps at 150 volts or ❑ Floating buildings.
Tess to ground, or exceeds 14,000 ❑ Commercial -use agricultural
❑ 1 - and 2- family dwelling Commercial/industrial ❑ Accessory building amps for all other installations. buildings.
❑ Multi - family ❑ Master builder ❑ Other: ❑ Fire pump. ❑ Installation of 75 KVA or
JOB SITE INFORMATION AND LOCATION ❑ Emergency system. larger separately derived system.
❑ Addition of new motor load of ❑ "A ", "E ", "1 -2 ", "I -3 ",
Job no.: I Job site address: 015 ?9 L4.)O�S /� , 1 or more. occupancy.
f� " ` ��1 ❑ Siix x o or r more residential units. ❑ Recreational vehicle parks.
City /State /ZIP: U Cl Health -care facilities. ❑ Supply voltage for more than
❑ Hazardous locations. 600 volts nominal.
Suite/bldg. /apt. no.: /f 0 I Project name: N- 4 oi ❑ Service or feeder 600 amps or more.
FEE SCHEDULE
Cross street/directions to job site: Description 1 Qty. 1 Fee. 1 Total 1 •
New residential single- or multi- family dwelling unit.
Includes attached garage.
Subdivision: Lot no.: 1,000 sq. ft. or less 168.54 4
Ea. add' 1 500 sq. ft. or portion 33.92 1
Tax map /parcel no.: Limited energy, residential
DESCRIPTION OF WORK (with above sq. ft.) 75.00 2
Limited energy, multi - family 75.00 2
., residential (with above sq. ft.)
Services or feeders installation, alteration, and/or relocation
200 amps or less 6 100.70 tipLi 2
❑ PROPERTY OWNER I ❑ TENANT 201 amps to 400 amps 133.56 2
401 amps to 600 amps 200.34 2
Name: 601 amps to 1,000 amps 301.04 2
Address: Over 1,000 amps or volts 552.26 2
Temporary services or feeders installation, alteration, and /or
City /State /ZIP: relocation
Phone: ( ) Fax: ( ) 200 amps or less 59.36 t
201 amps to 400 amps 125.08 2
Owner installation: This installation is being made on property that I own which is not
intended for sale, lease, rent, or exchange, according to ORS 447, 449, 670, and 701. 401 amps to 599 amps 168.54 2
Branch circuits — new, alteration, or extension, per panel
Owner signature: Date: A. Fee for branch circuits with
❑ APPLICANT I ❑ CONTACT PERSON above service or feeder fee, /1 7.42 ` 1 + V 7 2
each branch circuit
Business name: c S ` t � , v l B. Fee for branch circuits without
i service or feeder fee, first 56.18 2
Contact name: branch circuit
Each add'I branch circuit 7.42 2
Address: Miscellaneous (service or feeder not included)
City/State/ZIP: Each manufactured or modular 67.84 2
Y dwelling, service and/or feeder
Phone: ( ) Fax: : ( )
Reconnect only 67.84 2
Pump or irrigation circle 67.84 2
E - mail:
Sign or outline lighting 67.84 2
CONTRACTOR Signal circuit(s) or limited- energy
Business name: g_ F/ t Gfh. LLG panel, alteration, or extension. Page 2 2
Each additional inspection over allowable in any of the above
Address: 77 /2 /1/6 egg- !al/ Additional inspection (1 hr min) 66.25/ hr
City/State /ZIP: (/A - WeoU vEf_ //i4- 9d66 Z Investigation (1 hr min) 66.25/ hr
/, Industrial plant (1 hr min) 78.18/ hr
Phone: (963 ) 7q 0 ZZQ I Fax: (36 0 ) Z 5o 2350 Inspections for which no fee is 90.00 / hr
specifically listed (%z hr min) _
CCB Lic.: /p 7257 Electrical Lic.: C 7 , i / I Suprv. Lic f29� S ELECTRICAL PERMIT FEES
Suprv. Electrician i ure, required: ` �? 10 Subtotal: i SS 3, Cl
y� ++4 Plan review (25% of permit fee):
Print name: / t l F C 7-r g e Date: /1 , 2 - 20/ 0 State surcharge (12% of permit fee): 1 , if 7
TOTAL PERMIT FEE: 1 1 7/0, IA Li
Authorized signature: This permit application expires if a permit is not obtainkd within 180
days after it has been accepted as complete.
Print name: Date: • Number of inspections allowed per permit.
1:\Building\Permits\Et.C- PermitApp.doc 07/01 /10 440- 4615T(11 /05 /COM/WEB
Electrical Permit Application - City of Tigard
Page 2 - Supplemental Information
LIMITED ENERGY PERMIT FEES:
RESIDENTIAL WORK ONLY:
Fee for all residential systems combined $75.00
Check Type of Work Involved:
❑ Audio and Stereo Systems*
❑ Burglar Alarm
❑ Garage Door Opener*
❑ Heating, Ventilation and Air Conditioning System*
❑ Vacuum Systems*
❑ Other:
COMMERCIAL WORK ONLY:
Fee for each commercial $75.00
system
(SEE OAR 918- 309 -0000)
Check Type of Work Involved:
❑ Audio and Stereo Systems
❑ Boiler Controls
❑ Clock Systems
❑ Data Telecommunication Installation
❑ Fire Alarm Installation
❑ HVAC
❑ Instrumentation
❑ Intercom and Paging Systems
❑ Landscape Irrigation Control*
❑ Medical
❑ Nurse Calls
❑ Outdoor Landscape Lighting*
❑ Protective Signaling
❑ Other
Total number of commercial systems:
*No licenses are required. Licenses are required
for all other installations
I: \Building\Permits\ELC- PermitApp.doc 07/01/10
e l G cam® /U ''(/v 6O k5
JJOki 0 0 rlordiC light Recessed Monopoint
9 T43 -PMKR
English I A
INSTALLATION INSTRUCTIONS _
- READ ALL INSTRUCTIONS BEFORE INSTALLATION. r, -
IMPORTANT SAFETY INSTRUCTIONS:
• The Nordic Light Recessed monopoint T43 -PMKR mounting systems are intended for use with
lighting fixtures marked " For use with Nordic Light T43 track systems." To reduce the risk of fire
and electric shock, do not use other components with these Monopoint systems. ;
• Monopoint installation is only to be performed by a certified Electrician in accordance with the Na- B 2
tional Electrical Code and all local codes and standards.
• RATING: 1 phase 120V 50160z single branch circuit with a maximum capacity of 5 amperes.
• Do not use these Monopoint systems with a power supply cord or convenience receptacle adaptor. 1
• Do not install any fixture closer than six inches from combustible materials. :,
• Do not install any part of these Monopoint systems less than 5 feet above finished floor. '+ f t:..;) --
• Do not install the Monopoint in damp or wet locations. b...
• Do not install the Monopoint with electric power connected.
Similarly, disconnect electricity when installing or removing lighting fixtures or components or
changing the configuration of the Monopoint.
• Mechanical load: Max 50 N.
Installation of monopoint:
1. The Nordic Light T43 -PMKR Monopoint systems are supplied completely assembled, the conduit
is not attached.(A) C fi ,, '"
2. Secure the recessed monopoint at indicated positions using the locking device to ceiling.(B1)
3. Adjust the locking device so that the lower flange will be about 0,14" (3,5 mm) above the ceiling
' surface. (C1) +
4. Cut hole for ceiling in diameter 6" (152 mm).(C1) A _- T '. f w
5. Pull out the front rim and un -hook the springs.(E1 & E2) / ' ,' ,° . = ''_ j1.-
6. Disconnect power. 1
7. Disassemble plastic cover with screws (C2).
8. Route 120VAC into the mono -point (B2). \ 2
Connecting the main cables to Mono- point.
D
1. Connect the Power cable (Line) to the terminal marked L. '114,-, ��
2. Connect the neutral leader to the terminal marked N. i N i
3. Ground cable must be connected to terminal marked ground. T � ,I Q l
O
4. Replace cover with the two assembly screws, and tighten securely. DO NOT OVER- TIGHTEN , „ �;, . ., 1 .
.(C2) LO /( ,� I 7/
5. Snap in the front rim, by squeeze the torsion spring.(E1) � , r te / Ground
6. Install track lighting fixtures marked For use with Power Source T43 Track Systems: To the � , `7'-...1 P`t 7
Mon track adaptor receptacle. N � Strain Relief
Line
7. Activate branch power to the Monopoint and if the lighting fixture adaptor is supplied with an on /off
switch, make the circuit selection on the adaptor switch which powers the lighting fixtures.
E
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE i - s.,,,,,,
Ur I Ili
;
1
_ .
-71-) " b )‹.
. _
_ O Cc
1 '
r-
„
\ 2_
.,_611. 5), ■
Cubic
1:7 5 ' ?). 5 3 7 -LK”
.A.R2a6um ;I-17E
VoyL
;
337
7
E (v1A.k)
I 'Li 5 Quo(
/11 0 . O I 33
(Lc-c•Jc.-,
t) 5 CD
/7- (0_55 CAA 1 C.
n
''' ' - -,,,,:::,:,-,1,,,!' ,`'...,::,-,..,1:-,I,",,,i'-4-'-'1:i,,I,;::,--1;-,,'
.z'
:-
_ 5 49
3
i _ _
. , _ _ ,, ,iii ` :lr�;y i. tom...
s 'k > .. °rat; ,
_
? �
,. ' 3 rte' a
- : - "^ . � sr '
< '
;, .. - r Vi. "„ — ,_ . �
. 7;" „:" . ) itIk : 2 L c.". . - - - , .., ,>,, . 7. , ,,. ,, ,, ,
� i
x
r 0
d y
9 „ RM'"#.M'°'+' v% A1'� '� , 11 e � 1 a
_ " R7 6V.FJ? 63P , 5 b
r " : €' ' x'$ . t om ,tT ,
py i*
.�' �v '*tea' � �� � � -
te n . � �� a '.
s .,rc - ¢ e p �.r , ?'mot , x r x k , , t ,
n i,i&''' L { b4�. : 3*T Y4 2� -T ;' y ! 1'-: !:: . ,�.' `:+' + $_.., ' i
n
the standard in safety underwriters
Laboratories
File E331883 Vol 1 Issued: 2010 -01 -06
Revised: 2010 -01 -07
FOLLOW -UP SERVICE PROCEDURE
(TYPE R)
TRACK LIGHTS AND TRACKS
(IFFR,IFFR7)
Manufacturer: NORDIC LIGHT SUZHOU CO LTD
(114757 -001) 53 FACTORY
SUZHOU INDUSTRIAL PARK
LOUFENG EAST DISTRICT
SUZHOU
JIANGSU 215123 CHINA
Applicant: NORDIC LIGHT AB
(770320 -001) BOX 390
SE -931 24 SKELLEFTEA SWEDEN
Listee: SAME AS APPLICANT
(770320 -001)
This Procedure authorizes the above manufacturer to use the marking specified by
Underwriters Laboratories Inc.(UL), or any authorized licensee of UL, only on products
covered by this Procedure, in accordance with the applicable UL Services Agreement.
The prescribed Mark or Marking shall be used only at the above manufacturing location on such
products which comply with this Procedure and any other applicable requirements.
The Procedure contains information for the use of the above named Manufacturer and
representatives of Underwriters Laboratories Inc. and is not to be used for any other
purpose. It is lent to the Manufacturer with the understanding that it is not to be copied,
either wholly or in part, and that it will be returned to Underwriters Laboratories Inc. (UL)
or any authorized licensee of UL, upon request.
This PROCEDURE, and any subsequent revision, is the property of Underwriters Laboratories
Inc.)UL) and the authorized licensee of UL and is not transferable.
Underwriters Laboratories Inc.
Stephen Hewson William R. Carney
Senior Vice President Director
Global Follow - Up Service Operations North American Certification Program
File E331883 Vol. 1 Sec. 1 Page 6 Issued: 2005 -05 -25
and Report Revised: 2009 -01 -27
CATALOG DESIGNATIONS:
Max 120 Series and Max 277 Series Track Systems Consisting of Fittings
Cat. Nos.
May be provided with suffixes for commercial purposes:
Catalog Number Fig. No. Fitting
T4 -CE "Max" End Cap
T4 -CM "Max 120" Mini Coupler
T4 -CK "Max 120" Knuckle Connector
T4 -FE1 "Max 120" End Feed
T4 -FE2 "Max 120" Mirror End Feed
T4 -FL "Max 120" Adjustable L Feed - connector
T4 -FM "Max 120" Middle Feed - connector
T4 -FT1 "Max 120" Adjustable T Feed - connector
T4 -FT2 "Max 120" Adjustable Mirror T Feed - connector
T4 -FX "Max 120" X Feed - connector
T4 -FKJE "Max" Jbox End Feed Kit
T4 -FKJU "Max" Universal Jbox Feed Kit
T4 -HSC Fixture Safety Cable
T4 -MTC1 Track Mounting, twist -clip
T4 -MTC2 Track Mounting, twist -clip + ceiling -tile clip
T4 -MTC3 Track Mounting, twist -clip + dropped ceiling -tile
clip
T4 -MTC4 Track Suspension, twist - clip + zinc plated 4 -20
threaded stud, 7mm
T4 -MTC5 Track Suspension, twist -clip + zinc plated 4 -20
threaded receptacle, 12mm
T4 -MRP1 Joint Suspension Reinforcement, Plate for Mini
coupler, zinc plated
T4 -MRP2 Joint Mounting, plate + ceiling -tile clip
T4 -MRP3 Joint Mounting, plate + dropped ceiling -tile clip
T4 -MRP4, T4 -MS4 Joint Suspension Mounting, plate + 1/4 -20 threaded
stud, 7mm
T4 -MAP5, T4 -MS5 Joint Suspension Mounting, plate + 1/4 -20 threaded
receptacle, 12mm
T4 -FK "Max 120" Knuckle Feed
T4 -CF "Max 120" Flex Connector
T52 -CM, TS22 -CM, T4U -CM, "DiMax 277" Mini Coupler
T47CM
T52 -CK, TS22 -CK, T4U -CK, "DiMax 277" Knuckle Connector
T47 -CK
T52 -FE1, TS22 -FE1, T4U- "DiMax 277" End Feed
FE1,T47 -FE1
T52 -FE2, TS22 -FE2, T4U- "DiMax 277" Mirror End Feed
FE2,T47 -FE2
T52 -FL, TS22 -FL, T4U -FL, "DiMax 277" Adjustable L Feed - connector
T47 -FL
T52 -FM, TS22 -FM, T4U -FM, "DiMax 277" Middle Feed - connector
T47 -FM
T52 -FT1, TS22 -FT1, T4U- "DiMax 277" Adjustable T Feed - connector
FT1, T47 -FT1
T52 -FT2, TS22 -FT2, T4U- "DiMax 277" Adjustable Mirror T Feed - connector
FT2, T47 -FT2
T52 -FX, TS22 -FX, T4U -FX, "DiMax 277" X Feed - connector
T47 -FX
T52 -FK, TS22 -FK, T4U -FK, "DiMax 277" Knuckle Feed
T47 -FK
T52 -CF, TS22 -CF, T4U -CF, "DiMax 277" Flex Connector
T47 -CF
File E331883 Vol. 1 Sec. 1 Page 7 Issued: 2005 -05 -25
and Report Revised: 2009 -01 -27
Catalog Number Fig. No. Fitting
T73 -CM "TriMax 277" Mini Coupler
T73 -CK "TriMax 277" Knuckle Connector
T73 -FE1 "TriMax 277" End Feed
T73 -FE2 "TriMax 277" Mirror End Feed
T73 -FL "TriMax 277" Adjustable L Feed - connector
T73 -FM "TriMax 277" Middle Feed - connector
T73 -FT1 "TriMax 277" Adjustable T Feed - connector
T73 -FT2 "TriMax 277" Adjustable Mirror T Feed -
connector
T73 -FX "TriMax 277" X Feed - connector
T43 -PMK Monopoint
T43 -PMKS Monopoint with bracket for wire suspension
support of pendant fixture
T43 -PMKR Recessed Monopoint with trim
File E331883 Vol. 1 Sec. 1 Page 14 Issued: 2005 -05 -25
and Report Revised: 2006 -09 -19
Monopoint
T43 - PMK Fig. 7
General - See polymeric materials described on page 2 where described
below as plastic. The above model number may be provided with an additional
suffix.
1. Housing - Two pieces. Plastic, min. 1.5mm thick. Shaped as shown,
overall 100 mm dia. by 32 mm high.Provided with two mounting slots
measuring 5mm by 12 mm. Provided with one 11 mm opening for wires.
Top cover has 15 mm by 77 mm opening for securement of fixture
adaptors.
2. Line /Neutral connectors - Copper alloy, min. 1.5mm thick. Measures
13mm by 7 mm. Two provided. Provided with a 5/16 in. square tab for
pressure plate securement. Secured within housing.
3. Grounding - Copper alloy, min. 1.5 mm thick. Overall 37 mm by 7 mm,
secured to bottom of housing. Provided with a 5/16 in. square tab for
pressure plate securement.
4. Pressure Plate - Three provided. Plated copper alloy or steel, overall
5/16 in by 5/16 in with a 0.10 in (2.5 mm) dia. threaded opening for terminal
screw passage; threaded opening provided with a min. 2 full threads which
engages 0.11 in (2.8 mm) dia. terminal screw.
5. Markings - Provided in accordance Construction Details including the
following:
a. Supply terminal shall be identified with a marking other than
the markings identified for the Neutral and Ground. The marking
shall be located adjacent to the terminal.
b. Neutral terminal shall be identified with a marking such as
"N ", "NEUT" or "NEUTRAL ". The marking shall be located adjacent
to the terminal. The single letter "N" may be used to denote the
neutral terminal if instruction manual is provided with a
statement showing the marking and definition.
c. Equipment grounding terminal shall be identified with a
marking such as "GND ", "GRND ", "GROUND ", or the ground
symbol. The marking shall be located adjacent to the
terminal. The electrical symbol for ground may be used to denote
the ground terminal if instruction manual is provided with a
statement showing the marking and definition.
•
File E331883 Vol. 1 Sec. 1 Page 15 Issued: 2005 -05 -25
and Report New: 2009 -01 -27
MONOPOINT, CAT. NO. T43 -PMKS, FIG. 8
General - Cat. No. T43 -PMKS is identical to Fig. 7, except additionally
provided with brackets for wire suspension /support of pendant Luminaires.
Max weight is 20 lb. As shown.
1. Bracket - Cast Aluminum, min. 2.4 mm (0.09 in) thick. Overall 18.2 cm
(7 -1/4 in) long, 10 mm (4 in) wide max.
MONOPOINT, CAT. NO. 143 -PMKR, FIG. 9
General - Cat. No. T43 -PMKR is identical to Fig. 7, except additionally
provided with recessed housing, as shown.
1. Recessed Housing - Cast Alum. Min. 2.1 mm (0.08 in) thick. Overall
14.5 cm (5 -3/4 in) OD, 27 mm (1 -1/8 in) deep. Provided with openings
for securement of the decorative trim.