Plans . .
. .
i.c/ter3 oo(a
Installation 1: - _: -• - . - Jumper Locations
Genesis horns and strobes mount to any , .' .. To chang he from To change strobe from
-' ► r z ) temporal to steady steady to tem p
standard one -gang surface or flush electrical r ; R cut from circle J7 cut from circle J2
J
box. Matching optional trim plates accommo- E ji
.. ,t , to edge of circuit board to edge of circuit board
date one -gang, two -gang, four -inch square, or ? 'r ,: /
- octagonal boxes, and European 100mm square. i�! / •
�, rt a 0 0J20 0 0
All Genesis signals come pre - assembled with i �"'- `" ti �i 111111111 0
captive mounting screws for easy installation. - °--- -- - go of the si nal unlock the with op i o al trim l — 0
Two tabs at the top 9 with optional trim plate
cover to reveal the mounting hardware. The " °
shallow depth of Genesis devices leaves ample room behind the o t'11r :fit -
signal for extra wiring. Once installed with the cover in place, no
mounting screws are visible. Note: Use temporal strobe configuration for private mode
applications only.
Field Configuration • Genesis strobe -only and combination temporal horn /strobe
Temporal horn and horn /strobe models are factory set to sound in models may be configured for temporal flash. This battery- saving
feature is intended for private mode signaling only. To set the
a three -pulse temporal pattern. Units may be configured for use device for temporal flash, snip the circuit board as shown in the
with coded systems by snipping the circuit board as shown in the Jumper Locations diagram above.
Jumper Locations diagram at right. This results in a steady output
that can be turned on and off as the system applies and removes Non - temporal, horn -only models sound a steady tone. For field -
power to the signal circuit. A Genesis Signal Master is required selectable steady or temporal output, use a temporal horn.
when horn /strobe models are configured for coded systems.
Specifications
Housing Red or white textured UV stabilized, color impregnated engineered plastic. Exceeds 94V -0 UL flammability rating.
Flash tube enclosure Clear polycarbonate
Mounting Flush mount: 21/2 inch (64 mm) deep one -gang box
(indoor wall mount only) Surface mount: EST model 27193 surface mount box, wiremold box, or equivalent surface -mount box
With optional trim plate: One -gang, two -gang, four -inch square, octagonal, or European single -gang box
Wire Connections Two screw terminals: single input for both horn and strobe. #18 to #12 AWG (0.75 mm to 2.5 mm wire size
• Operating environment 32 -120 °F (0 -49 °C) ambient temperature. 93% relative humidity
Agency UL 1971, UL 1638, UL 464, ULC S525, ULC S526, MEA, FM, CSFM, CE, FCC.
Listings /Approvals (All models comply with ADA Code of Federal Regulation Chapter 28 Part 36 Final Rule.)
Dimensions (HxWxD) Signal: 4 -1/2° x 2 -3/4" x 13/16° (113 mm x 68 mm x 21 mm)
Trimplate: 5" (127 mm); Height - 5 -7/8° (149 mm); Depth -' /2 (13 mm)
Strobes: 20 - 31 Vdc filtered continuous only
Operating Voltage 20 - 27 Vdc FWR (full wave rectified) continuous only
Horns: 20 - 31 Vdc filtered continuous (or coded when horn set to continuous - non temporal - output)
20 -27 Vdc FWR continuous (or coded when horn set to continuous - non temporal - output)
Strobe output rating UL 1971, UL 1638, ULC S526: 15 cd, 30 cd, 60 cd, 75 cd or 110 cd
Self- synchronized: one flash per second within 200 milliseconds over 30 minutes on common circuit.
Strobe flash rate With optional Signal Master: one flash per second within 10 milliseconds indefinitely.
Temporal setting (private mode only): synchronized to temporal output of horns on the same circuit.
Temporal Horn: Synchronized at temporal rate within 200 milliseconds over thirty minutes on common circuit. With
Horn pulse rate optional Signal Master, synchronized at temporal rate within 10 milliseconds indefinitely.
Horn: Continuous only.
Temporal audible pattern 1/2 sec ON, '/2 sec OFF,' sec ON, 1/2 sec OFF, 1/2 sec ON, 11/2 sec OFF, then repeat cycle
EDWARDS SYSTEMS TECHNOLOGY
Page 4 of 8 literature Sheet #85001-0529 Issue 6
Not to be used for installation purposes.
For the most current literature and updates visit www.est.net.