Permit UY `'
ii a CITY OF T MECHANICAL PERMIT
COMMUNITY DEVELOPMENT PERMIT #: MEC2008 -00543
TIGARD 13125 SW Hall Blvd., Tigard, OR 97223 503.639.4171 DATE ISSUED: 11/10/2008
PARCEL: 1 S136CD -00500
SITE ADDRESS: 08050 SW PFAFFLE ST 110 ZONING: C -P
SUBDIVISION: PACIFIC CROSSROADS CORP LOT: JURISDICTION: TIG
PROJECT: ACCOUNTAX
Project Description: Installing new rooftop unit. Valuation: $9,800.00
CLASS OF WORK: ALT FLOOR FURN: EVAP COOLERS:
TYPE OF USE: COM UNIT HEATERS: VENT FANS: 2
OCCUPANCY GRP: B VENTS W/O APPL: VENT SYSTEMS:
STORIES: 1 BOILERS /COMPRESSORS HOODS:
FUEL TYPES 0 - 3 HP: 1 DOMES. INCIN:
NAT 3 - 15 HP: COMML. INCIN:
MAX INPUT: BTU 15 - 30 HP:
FIRE DAMPERS ?: 30 - 50 HP: REPAIR UNITS:
GAS PRESSURE: 50 + HP: WOODSTOVES:
FURN < 100K BTU: AIR HANDLING UNITS CLO DRYERS:
OTHER UNITS:
FURN > =100K BTU: <= 10000 cfm: GAS OUTLETS: 1
> 10000 cfm:
Owner: FEES
ACCOUNTAX Description Date Amount
10300 SW GREENBURG RD
SUITE375 [MECH] Permit Fee 11/10/20( $227.90
TIGARD, OR 97223 [MECPLN] Plan Rev 11/10/20( $56.98
[TAX] 12% State Surch 11/10/20( $27.35
Phone: 503 -619 -1040 Total $312.23
Contractor:
OREGON HEATING & NC
PO BOX 397
DUNDEE, OR 97115 REQUIRED ITEMS AND REPORTS
Contact #: PRI 503 -538 -2953
FAX 503- 345 -6628
Reg #: LIC 172126
This permit is issued subject to the regulations contained in the Tigard Municipal Code, State of Ore. Specialty Codes and all other
applicable laws. All work will be done in accordance with approved plans. This permit will expire if work is not started within 180 days of
issuance, or if work is suspended for more than 180 days. ATTENTION: Oregon law requires you to follow rules adopted in the Oregon
Utility Notification Center. Those rules are set forth in OAR 952 - 001 -0010 through OAR 952 - 001 -0100 You may obtain copies of these
rules or direct questions to OUNC by calling 503.246.6699 or 1.800.332.2344.
Iss • ed By: ∎ 4 i j / I A, Permittee Signature:
Call 503.639.4175 by 7:00 a.m. for inspection that business day.
This permit card shall be kept in a conspicuous place on the job site until completion of the project.
Approved plans are required on the job site at the time of each inspection.
CITY OF TIGARD
BUILDING DIVISION PERMIT #: MF 0200 -0 543
13125 SW Hall Blvd., Tigard, OR 97223 I D ATE ISSUED: 11/10/2008
Phone: (503) 639 -4171 r A a to
Inspection Requests (24 Hrs.): (503) 639 -4175 . �. . __..
INSPECTION WORKSHEET FOR DATE: 11/19/2008 TIME: 7:O2AM PAGE: 20
SITE ADDRESS: Ooo50 SW PFAFFLE ST 1 1O CLASS OF WORK:
SUBDIVISION: PACIFIC CROSSROADS CORP LOT #: TYPE OF USE:
PROJECT NAME: ACCOUNTAX
DESCRIPTION: Installing new rooftop unit. Valuation: $9,800.00
OWNER: ACCOUNTAX, PHONE #: 503.618 - 10.10
CONTRACTOR: OREGON HEATING & NC PHONE #: 503 -538 -2953
Inspection Request Scheduled For: Date: 11/19/2008 Pour Time:
Code # Inspection Description Confirm # Contact # Message
615 Mechanical rough - in 078243 -01 503 -538 -2953 N
Corrections /Comme /Instructions:
4 ,1.,/, _ "I( ...
74 -ASS ❑ PARTIAL APPROVAL ❑ CANCEL ❑ NO ACCESS
❑ FAIL ❑ CALL FOR INSPECTION ❑ ADDITIONAL FEES ASSESSED
j nsector: ZIN, Date: 11/ ( Phone #: (503) 718- ��
4 - a - .
CITY OFTIGARD `3 ' ,
BUILDING DIVISION PERMIT #: MEC200O -0043
13125 SW Hall Blvd., Tigard, OR 97223 DATE ISSUED: 11/10/2008
Phone: (503) 639 -4171 p, J6
Inspection Requests (24 Hrs.): (503) 639 -4175 .'"71.1. I
e
INSPECTION WORKSHEET FOR DATE: - 11/12/2008 •TIME:. 7 :OOAM PAGE: 5
SITE ADDRESS: 0 13050 SW PFAFFLE ST 110 CLASS OF WORK:
SUBDIVISION: PACIFIC CROSSROADS CORP LOT #: TYPE OF USE:
PROJECT NAME: ACCOUNTAX
DESCRIPTION: Installing new rooftop unit., Valuation: $9,800,00
OWNER: ACCOUNTAX, PHONE #: 603- E;1911110
CONTRACTOR: OREGON HEATING & A/C PHONE #: 503 - 538 -2963
Inspection Request Scheduled For: Date: 11/12/2008 Pour Time:
Code # Inspection Description Confirm # Contact # Message
610 Gas line 077979-01 503 - 538 -2953 N
Corrections /Comments /Instructions:
`,
V
,
��-,,_
(00p/7; o.
cli\e .4- (pqi Af"',) c.
f
® Q
• 4
G
Qe. -vi/ e
PASS PARTIAL APPROVA . n CANCEL V ❑ NO ACCESS
e 0
❑
FAIL CA L FOR INSPECTION n ADDITIONAL FEES ASSESSED
Y Inspector: 4 t .� Date: /,?/lio'v a ' Phone #: (503) 718- "C%
j
r
Mech P mit Applica �w FOR OFFICE USE ONLY
City of Tigard Date/By: . ali0 id , Permit No.: r , 1l
° 13125 SW Hall Blvd., Tigard, OR 97223 0
Phone: 503.639.4171 Fax: 503.598.1960 Plan Revie
/
Date/By: KJ Other Permit: 7� I . La •
�- I G D Inspection Line: 503.639 el Date ReadyBy: � Juris: See Page 2 for
Internet: www.tigard or.gov e ed /Method: `' / do- , `~6. Supplemental Information
l � e- , til
E OF WO � `' COMMERCIAL FEE* SCHEDULE — USE CHECKLIST
❑ New construction ddition/alte elT 1
'�C[ Mechanical permit fees* are based on the value of the work
` performed. Indicate the value (rounded to the nearest dollar) of all
0
❑ Demolition ❑ Other. QANG mechanical materials, equipment, labo ove_ Ih 1 and profit.
CA ORY OF C UCTION Value: $ �(3�
RESIDENTIAL EQUIPMENT / SYSTEMS FEES*
❑ 1- and 2- family dwelling Commercial /industrial ❑ Accessory building
For special information use checklist.
❑ Multi- family ❑ Master builder ❑ Other: Description I Qty. I Ea. I Total
JOB SITE INFORMATION AND LOCATION Heating/cooling
Job site address: (0<70 Air conditioning or heat pump
S51-1) I / F C C (requires site plan showing placement ) 14.00
City /State /ZIP: fi 19 An -rte or
Furnace 100,000 BTU (ducts/vents) 14.00
Furnace 100,000+ BTU (ducts/vents) , 17.90
Suite/bldg. /apt. no.: /1 a Project name: A 6. o ti r
Gas heat pump 14.00
Cross street/directions to job site: Duct work 10.00
9y14' Hydronic hot water system 14.00
Residential boiler (radiator or
hydronic) 14.00
Unit heaters (fuel -type, not electric),
in -wall, in -duct, suspended, etc. 14.00
Flue /vent for any of above 6.80
Subdivision: Lot no.:
Other: 10.00
Tax map /parcel no.: Other fuel appliances
DESCRIPTION OF WORK Water heater 10.00
Gas fireplace 10.00
I /24 Pe - f'V V _ 44 Flue vent for water heater or gas
(�' ?).D fireplace 10.00
Y A N $ j b ✓i tt, 4 Log lighter (gas) 10.00
Wood/pellet stove 10.00
• Wood fireplace /insert 10.00
❑ PROPERTY OWNER ❑ TENANT Chimney /liner /flue /vent 10.00
Other: 10.00
Name: Environmental exhaust and ventilation
Address: Range hood/other kitchen
equipment 10.00
City /State /ZIP: Clothes dryer exhaust 10.00
Single -duct exhaust (bathrooms,
Phone: ( ) Fax: ( . - ) toilet compartments, utility rooms) 6.80
*APPLICANT ❑ CONTACT PERSON Attic /crawlspace fans 10.00
D�)Q Other: 1 0.00
Business name: Fuel i in
PP� I;
Contact name: /?. z ....,) �,r" L All &-V2- $5.40 for first four; $1.00 for each additional
Address: (� Furnace, etc.
Gas heat pump -
City/State /ZIP: Wall /suspended/unit heater
Phone: ( )q g'‘,b'L Fax: : ( ) Water heater
t � Fireplace
E -mail: �1 l L4+ 9 L ' .D'' ka op,- Range
T1'll�t{A�� �
CO CTOR Barbecue
oleo p / Clothes dryer (gas)
Business name: C �
Other:
`
Address: v �-1✓ -- 3e" T MECHANICAL PERMIT FEES*
City/State /ZIP: 9 J c2( - i \-‹ Subtotal
Phone: (g,2 ) 043 ' �1. s 3 Fax: ( � 2,1, -L Minimum permit fee permit fee)
/ � Plan review (25% of permit fee)
CCB lie.: t "7 7,1 State surcharge (12% of permit fee)
TOTAL PERMIT FEE
Authorized signature: &14/1"-- This permit application expires if a permit is not obtained within 180
days a it has been accepted as complete.
Print name: c= V I Date: ( Vc(Ots • Fee metho dology set by Tri- County Building Industry Service Board
1:\ BuildingWermits \MEC- PermitApp.doc 01/19/07 440-COM/WEB)
• i
Mechanical Permit Application. - City of Tigard - •.�
Page 2 - Supplemental Information
•
Commercial Fee Schedule:- .. + r , '
Total Valuation: Permit Fee:'
$1.00 to $2,000.00 Minimum fee $72.50 •
$2,001.00 to $5,000.00 $72.50 for the first $2,000.00 and $2.30
• for each additional $100.00 or fraction
thereof, to and including $5,000.00.
$5,001.00 to $10,000.00 $141.50 for the first $5,000.00 and
$1.80 for each additional $100.00 or
fraction thereof, to and including
$10,000.00.
$10,001.00 to $50,000.00 $231.50 for the first $10,000.00 and
$1.35 for each additional $100.00 or
fraction thereof, to and including
$50,000.00.
$50,001.00 to $100,000.00 $771.50 for the first $50,000.00 and
•
$1.25 for each additional $100.00 or
fraction thereof, to and including
$100,000.00.
$100,000.01 and up $1,396.50 for the first $100,000.00 and
$1.10 for each additional $100.00 or
fraction thereof.
Note: All new commercial buildings require 2 sets of plans.
•
1:\Building\Permits\MEC- PermitApp.doc 01/19/07
2
^ Form'4a Project Name:I /1(,C 1 Page:` I I
SYSTEMS - GENERAL ACc Do N Nex. Part 1 of 6
Applicability p l ow compliance Discussion of qualifying annce byy including a drawing sheet, detail number,
exceptions on page 4-25 specification section and subparagraph.
1. Applicablity (Section 1317)
Is this form required?
Form Required. Complete form if a new HVAC system is being installed, or components of an
existing HVAC system are being replaced (I.e., equipment, controls, ductwork, and insulation.)
❑ Exception. The building or part of the building qualifies for an exception from HVAC code
requirements. Applicable code exception is Section 1317.1. Portions of the building that
qualify:
Area:I I Exception ❑ -1 ❑ -2 ❑ -3
Area:1 I Exception ❑ -1 ❑ -2 ❑ -3
Arena I Exception ❑ -1 ❑ -2 ❑ -3
❑ Form Not Required. This project does not contain work required to comply with code.
Simple or Complex Systems (Section 1317.9 or 1317.10)
Building contains only Simple HVAC System(s). Com lete this form and
Simple System. B g y 4a p p (4a)
equipment efficiency worksheets as required. Form 4b is not required.
❑ Complex System. Project includes a Complex System. Complete this form (4a), form 4b and
• equipment efficiency worksheets as required.
3. Equipment Performance (Section 1317.5)
❑ No New HVAC Equipment. The building plans do not call for new electrical HVAC equipment,
combustion heating equipment, or heat - operated cooling equipment.
Complies. All new HVAC equipment have efficiencies not less than those required by code.
The following equipment efficiency worksheets are attached:
)fiii ❑-4b ❑-4c ❑-4d L3 -4e ❑-4f ❑ -4g ❑-4h ❑-4i ❑ -4j
4. Duct Insulation and Sealing (Sections 1317.7 & 1317.8)
❑ No Ducts. The building plans and specifications do not call for new HVAC ducts or plenums.
Complies. The plans and specifications call for all air - handling ducts and plenums to be insulated
and sealed as required by Sections 1317.7 &1317.8.
5 Distribution Transformers (Section 1316.1)
No Distribution Transformers. The plans /specs do not call for new distribution transformers.
❑ Complies. All new distribution transformers comply with efficiency, testing, and labeling
requirements of Section 1316.1.1.
❑ Exception. The project qualifies for an exception per Section 1316.1.1, Exceptiion:
❑-1 0-2 ❑-3 0-4 0-5 0-6 U-7 0-8 ❑ -9 0-10 0-11 0-12 an ❑-14
Attach relevant documentation for appropriate exception. The plans /specs show compliance in the
following locations:
1� I
ap`ssyl %i
` rs�a
4 -1
Compliance with OSSC, effective 04/01/07
Form 4a Project Name:I ACrikerlYry I Pagel I
SYSTEMS - GENERAL Part 2 of 6
6. HVAC Controls (Section 1317.4)
.1 System Thermostat /Zone Controls (Section 1317.4.1)
Complies. All new HVAC systems include at least one temperature control device responding to
temperatures within the zones.
❑ Exception. HVAC system qualifies for an exception from zone control requirements.
The applicable code exception is Section 1317.4.2, Exception ❑ -1 ❑ -2
Portions of the building that qualify: I
The plans/specs show compliance in the following locations:
I I
t. 6.2 Off-hour Controls - Auto Setback or Shutdown (Section 1317.4.3)
Complies. Systems must have at least one of the following features:
Control Setback Complies. Each system is equipped with automatic control capable of
reducing energy through control setback during periods of non -use or alternate use of spaces
Equipment Shutdown Complies. Each system is equipped with controls capable of reducing
energy use through automatic shutdown during periods of non -use or alternate use of spaces.
1 HVAC systems with equipment shutdown are equipped with at least one of the following:
Programmable controls (1317.4.3.1 (1))
Occupant sensor (1317.4.3.1 (2))
❑ Interlocked to a security system (1317.4.3.1 (3))
❑ Manually activated timers with 2-hour operation max (1317.4.3.1 (4))
❑ Exception. The building qualifies for an exception to the requirement for automatic setback or
shutdown controls. The applicable code exception is Section 1317.4.3 Exception ❑ -1 ❑ -2
The plans /specs show compliance in the following locations:
I 1
6.3 Control Capabilities (Sec. 1317.4.2.1)
Complies. Zone thermostats are capable of being set to the temperatures described in Sec.
1317.4.2.1. Where used to control both heating and cooling, zone controls shall be capable of
providing a temperature range or deadband of at least 5 degrees F within which the supply of
heating and cooling energy to the zone is shut off or reduced to a minimum.
❑ Exception. The building qualifies for an exception to the deadband requirements.
The applicable code exception is Section 1317.4.2.1 Exception ❑ -1 ❑ -2
Portions of the building that qualify: I I
The plans /specs show compliance in the following locations:
I I
6.4 Optimum Start Controls (Section 1317.4.3.2)
❑ Complies. Separate HVAC systems have controls capable of varying start-up time of system to
ust meet temperature set point at time of occupancy.
Exception. HVAC systems have a design supply air capacity not exceeding 10,000 cfm.
The plans/specs show compliance in the following locations:
I
.5 Heat Pump Controls (Section 1317.4.4)
No Heat Pump. The plans /specs do not call for a new heat pump
Complies. All new heat pumps equipped with supplementary heaters are controlled to minimize
the use of supplemental heat as defined in Section 1317.4.4.
!'Z, The plans/specs show compliance in the following locations:
c
I
4-2
Compliance with OSSC, effective 04/01/07
Form 4a Project Name:I /^Ili 7fr I Page:I 3 I
SYSTEMS - GENERAL Part 3 of 6
7. Economizer Cooling (Section 1317.3)
❑ No Cooling. The building plans do not call for a new fan s with mechanical cooling.
Complies. Each new fan system has an air economizer capable of modulating outside -air and
return-air dampers to provide up to 100 percent of the design supply air as outside air.
❑ Exception At least one new fan system qualifies for an exception. The applicable code exception
is Section 1317.3, Exception ❑ -1 ❑ -2 ❑ -3 ❑ - ❑ -5 ❑ -6 ❑ -7
If Exception 3 is selected complete the following:
(a) Total cooling capacity of exempt units ( Btu/hr) I I
(b) Total installed building cooling capacity ( Btu/hr) I
❑ Complies. Sum of exempt units rated at less than 54,000 Btu/hr is <240,000 or a/b
< 0.10 (10% of total building cooling capacity). I
Unit Identifier of exempt units: I
The plans/specs show compliance in the following locations:
8. Economizer Pressure Relief & Integration (Section 1317.3.1 and 1317.3.2)
❑ No Economizers Required. Project does not contain a new fan system requiring economizers.
> 4 Overpressurization Complies. The drawings specifically identify a pressure relief mechanism for
each fan system that will relieve the extra air introduced by the economizer.
❑ Integration Complies. Economizer is capable of providing partial cooling even when additional
mechanical cooling is required to meet the remainder of the cooling load.
❑ Exception. The applicable exception is Section 1317.3.2, Exception ❑ -1 ❑ -2
The plans/specs show compliance in the following locations:
1
9 Hot Gas Bypass (Section 1317.5)
No Hot Gas Bypass
❑ Complies. See allowable amount of hot gas bypass as a percentage of total cooling capacity in
table below.
Unit ID Rated Cooling Capacity Hot Gas Bypass Capacity
�., Allowable Hot Gas Bypass
E - , Rated Cooling Capacity Max Hot Gas Bypass
A24O,000 Btu /hr 50%
Ws, >240,000 Btu /hr 25%
❑ Exception. Unitary packaged system with cooling capacity no greater than 90,000 Btu/h
4 -3
Compliance with OSSC, effective 04/01/07
Form 4a Project Name:I A2.4 4!) I Page:I /
SYSTEMS - GENERAL Part 4 of 6
1 . Shutoff Dampers (1317.4.3.3)
Not Required. Shutoff dampers are not required on this project.
Complies. Each outdoor air supply & exhaust system shall be equipped with motorized dampers
❑ Exception. The building qualifies for an exception to the motorized damper requirement. The
applic -able code exception is Section 1317.4.3.3 Exception ❑ -1 ❑ -2 ❑ -3 ❑ -4 ❑ -5
The plans /specs show compliance in the following locations:
I
0 ,10.1. Shutoff Damper Controls (Section 1317.4.3.3.1)
Complies. Outdoor air supply and exhaust systems shall be provided dampers that automatically
shut when systems or spaces served are not in use or during building warm -up, cooldown, or
setback.
❑ Complies. Stair and shaft vents are capable of being automatically closed during normal building
operation and interlocked to open as required by fire and smoke detection systems.
The plans /specs show compliance in the following locations:
I
10.2. Motorized Damper Leakage (1317.4.3.3.2)
❑ Complies. Motorized outdoor air supply and exhaust air dampers have a maximum leakage rate
of 4 cfm/ft2 at 1.0 in w.g. when tested in accordance with AMCA Standard 500 -1998.
Exception. Packaged HVAC equipment may have maximum leakage rate of 20 cfm /ft at 1.0 in
w.g. when tested in accordance with AMCA Standard 500 -1998.
The plans /specs show compliance in the following locations:
1. Piping Insulation (Section 1314)
No New Piping. The building plans and specifications do not call for new piping serving a
heating or cooling system or part of a circulating service water heating system.
,01-7A.. Complies. All new piping serving a heating or cooling system or part of a circulating service
, .., water
r water heating system complies with the requirements of the Code, Section 1314.1.
Exception. New piping qualifies for exception: Section 1314.1, Exception ❑ -1 ❑ -2 .
12. Occupancy Ventilation
Complies. Mechanical ventilation systems provide the required amount of ventilation specified
in Chapter 4 of the Oregon Mechanical Specialty Code.
❑ Complies. Natural ventilation systems provide required amount of ventilation as certified by a
reg- istered architect or engineer as specified by Section1203.4.1, Exception. Attach worksheet
The plans /specs show compliance in
the following locations:
The plans /specs show compliance
on the following pages:
4-4
Compliance with OSSC, effective 04/01/07
•
•
•
Form 4a Project Name:I Ark, f ',X ( I Pagel ,
SYSTEMS - GENERAL Part 5 of 6
13. High Occupancy Ventilation (Section 1317.2.2)
❑ Complies. HVAC systems with ventilation air capacities of 1,500 CFM or greater that serve
areas having an average occupant load of 20 square feet per person or less from Table
1004.1.2 have a means to automatically reduce outside air intake.
Identify applicable systems: I
Plans /specs indicate where equipment (i.e. carbon dioxide sensor) and sequence is specified:
I
I- Exception. HVAC systems are equipped with an energy recovery device with at least 50%
recovery effectiveness.
No High Occupancy Systems. Project does not contain an HVAC system as described above.
4 Exhaust Air Heat Recovery (Section 1318.3)
Not Regulated. HVAC system does not have: 1) design supply air cap. of >10,000 cfm, and 2)
min. outside air supply >70 %, and 3) at least 1 exhaust fan rated at 75% of min outside air
❑ Complies. Heat recovery system increases outside air temperature by 20 °F (Climte Zone 1) or
30 °F (Zone 2) and has provision to provide bypass during air economizer mode.
❑ Exception. An HVAC system qualifies for an exception to this requirement. Applicable
exception from Section 1318.3 Exception I] -1 ❑ -2 ❑ -3 ❑ - ❑ -5 I] -6 0 - 7
The plans/specs show compliance in the following I
locations:
. Large Volume Fan Systems (Section 1318.4.2.4)
Not Regulated. The building plans or specifications do not call for fan systems over 15,000
CFM that serve a single zone and function for the purpose of temperature control.
❑ Complies. Fan systems are equipped with variable frequency drive or two speed motor to
reduce airflow as required by Section 1318.4.2.3.
The plans/specs show compliance in the following (
locations:
. Variable Speed Drives (Section 1317.10.3.1)
Not Regulated. The building plans or specifications do not call for fan and pump motors 10
horsepower and greater that serve variable -flow air or liquid systems.
❑ Complies. All fan and pump motors 10 hp and greater which serve variable -flow air or liquid
systems are controlled by a variable -speed drive.
❑ Exception. The building qualifies for an exception to the variable -speed drive requirement.
Portions of the building that qualify: I
Applicable code exception is Section 1317.10.3.1, Exception
The plans/specs show compliance in the following I
locations:
. Service Water Heating (Sec. 1315)
No New Water Heating. The building plans and specifications do not call for new water
heaters, hot water storage tanks or service hot water distribution systems.
❑ Complies. All new water heaters, hot water storage tanks or service hot water distribution
systems comply with the requirements of the Section 1315.
❑ Exception. The applicable code exception is Section: I Exception:
" ? ` Portions of the building that qualify:
The plans/specs show compliance in the following locations:
I
4-5
Compliance with OSSC, effective 04/01107
•
• Form 4a Project Name:I //1 z/+ A. I Page:1 (U 1
SYSTEMS - GENERAL Part 6 of 6
1 8. swimming Pools, Spas and Hot Tubs (Section 1315.5)
No New Pools. The building plans and specifications do not call for new, swimming pools, spas or
hot tubs.
❑ On /Off Controls Complies. Spa and hot tub heaters are equipped with a readily accessible
ON/OFF switch as required by Section 1315.5.1.
❑ Ventilation Controls Complies. Pool ventilation system is controlled based on humidity.
❑ Cover Complies. All heated pools, hot tubs and spas are equipped with a cover.
❑ Heat Recovery Complies. Pools, Spas, and hot tubs, over 200 ft utilize recovered heat as
required by Section 1315.5.3.
❑ Exception. Heat recovery is not necessary as pool is heated by renewable energy or waste
heat recovery sources capable of providing at least 70 percent of the heating energy
required over an operating season.
9. Fume Hoods (Section 1317.2.1.)
No Fume Hoods. The building plans do not call for fume hood systems that have a total exhaust
rate greater than 15,000 cfm.
❑ Complies. Fume hood systems have at least one of the following features:
❑ Variable air volume hood exhaust and room supply systems capable of reducing exhaust
and makeup air volume to 50% or less of design values.
❑ Direct makeup (auxiliary) air supply equal to at least 75% of the exhaust rate, heated no
warmer than 2° F below room set point, cooled no cooler than 3° F above room set point,
no humidification added, and no simultaneous heating and cooling used for
• dehumidification control.
❑ Heat recovery systems to precondition makeup air from fume hood exhaust in accordance
with 1318.3 - Exhaust Air Energy Recovery, without using any exception.
The plans/specs show compliance in the following locations:
I I
Z Parking Garage Ventilation (Section 1317.2.3)
o Enclosed Garages. The building plans and specifications do not call for enclosed Group S-2
parking garages with a ventilation exhaust rate greater than 30,000 CFM.
❑ Complies. The plans and specifications call for carbon monoxide sensing devices as required by
Section 1317.2.3.
❑ Exception. Open parking garages.
2 1. Kitchen Hoods (Section 1317.11)
Not Regulated. The plans /specs do not call for any new kitchen hoods with exhaust capacity
greater than 5,000 cfm each.
❑ Complies. All new kitchen hoods with a total exhaust capacity greater than 5,000 cfm have at
least 50 percent of the required makeup air; (a) unheated or heated to no more than 60 °F; and (b)
uncooted or evaporatively cooled.
."� The plans /specs show compliance in the following locations:
2. Outside Heating Systems (Section 1317.12)
No Outside Heating Systems. The plans /specs do not call for new permanently installed heating
systems outside the building.
❑ Complies. All new permanently installed outside heating systems are radiant gas fired systems
controlled by an occupancy sensor or timer switch as required by Section 1317.12.
4- 6
Compliance with OSSC. effective 04/01/07
CITY OF TIGARD
BUILDING DIVISION PERMIT #: MEC 0 00E 3
13125 SW Hall Blvd., Tigard, OR 97223 D ATE ISSUED: 1111 {1/2008
Phone: (503) 639 -4171 tmu�(ge�i�„
Inspection Requests (24 Hrs.): (503) 639 -4175 �:_
INSPECTION WORKSHEET FOR DATE: 1/2/200 TIME: 7 :01AM PAGE: 9
SITE ADDRESS: 08050 SW PFAFFLE ST 110 CLASS OF WORK:
SUBDIVISION: PACIFIC CROSSROADS CORP LOT #: TYPE OF USE:
PROJECT NAME: ACCOUNTAX
DESCRIPTION: Installing new rooftop unit. Valuation: $9,800.00
OWNER: ACCOUNTAX, PHONE #: 503-619-'1040
CONTRACTOR: OREGON HEATING & NC PHONE #: 503-538.2953
Inspection Request Scheduled For: Date: 1/2!2009 Pour Time:
Code # Inspection Description Confirm # Contact # Message
699 Mechanical final 079342 -01 503691 -9699 N
Corrections /Comments / Instructions:
C �� p• _ ! • PARTIAL APPROVAL ❑ CANCEL ❑ NO ACCESS
❑ FAIL • CALL FOR INSPECTION ❑ ADDITIONAL FEES ASSESSED
Inspector: .w A- Date: / 2 11 Phone #: (503) 718-
ZA
Oregon Heating
& Air Conditioning
Air Balance Report
Job Name: Accountax
Job Address: 8050 SW Pflaffle
Date Completed: Jan 2, 2009
Written By: Todd A. Bly
Equipment Schedule:
•
• System: . • .Make: Model: Serial No.:
RTU -1 Trane YSC072A3EMA37D 845101934L
• EF -1,2 Nutone QTRN80
EF3,4 Nutone QTRN 150
Testing Equipment:
Instrument: - Model #:
Shortridge Flowhood 8400
UEI Anemometer DAFM2
Dwyer Magnehelic
Ideal Multimeter 61 -730
Fieldpiece RPM Gauge SRPM1
•
•
•
Oregon Heatin
a a, ca,wn�,,.r g . �.
Office 503.538.2953 • Fax 503.537.2172 • PO Box 397 • 992 Highway 99 West • Dundee, OR 97115
800- Furnace
Oregon CCB #172126 • Washington #OREGOHA045D9 L1•�
www.oregonheating.co
•
Equipment Area served # Size Blow Spec CFM Test #1 Test#2 Test3 Final CFM
RTU -1 Supply Office 100 1 10 in 4W 350 396 360 360
Office 104 2 10 in 4W 350 445 404 404
Office 109 3 10 in 4W 350 419 381 381
Office 114 4 10 in 4W 350 430 391 391
Blower Rpm: 940 803 Total Supply 1536
RTU -1 Return Office 100 1 10 in 294 267 267
Office 104 2 • 10 in 365 332 332 •
Office 109 3 10 in 355 323 323
Office 114 _ 4 10 in 400 _ 364 _ 364
Total Return 1286
Total OSA 16% 250
RTU -2 Supply Entry 106 1 8 in 4W 170 209 209
Entry 106 2 8 in 4W 170 188 188
Office 103 3 10 in 4W 240 172 172
Office 102 4 8 in 4W 150 133 133
Office 101 5 8 in 4W 150 129 129
Hallway 6 8 in 4W 125 127 127
Office 107 7 8 in 4W 180 134 134
Office 108 8 8 in 4W 180 212 212
Conference 9 10 in 4W 220 245 245
Conference 10 10 in 4W 220 234 234
Break 117 11 8 in 4W 130 130 130
Office 116 12 10 in 4W 210 319 319
Office 113 13 10 in _ 4W 210 258 258
Blower Rpm: 876 Total Supply 2490
RTU -2 Return Entry Hallway 1 12 in 339 314 314
•
Conference 2 14 in 341 316 316
Office 103 3 8 in 180 155 155
Office 102 4 8 in 151 126 126
Office 101 5 8 in 575 550 550
Office 116 6 10 in 202 177 177
Office 113 7 _ 10 in 281 256 _ 256
Total Return 1894
Total OSA 24% 596
•
i
CITY OF TIGARD
BUILDING DIVISION PERMIT #: MEC2000.005A3
13125 SW Hall Blvd., Tigard, OR 97223 DATE ISSUED: 11/10/2008
Phone: (503) 639 -4171 ittighlll
Inspection Requests (24 Hrs.): (503) 639 -4175
INSPECTION WORKSHEET FOR DATE: 12/19/2008 TIME :OOAM PAGE: 21
SITE ADDRESS: 08050 SW PFAFFLE ST 110 CLASS OF WORK:
SUBDIVISION: PACIFIC CROSSROADS CORP LOT #: • TYPE OF USE:
PROJECT NAME: ACCOUNTAX
DESCRIPTION: Installing new rooftop unit. Valuation: $9,800.00
OWNER: ACCOUNTAX, PHONE #: 503-619 -10.10
CONTRACTOR: OREGON HEATING & NC PHONE #: 503
Inspection Request Scheduled For: Date: 12/19/2008 Pour Time:
Code # Inspection Description Confirm # Contact # Message
615 Mechanical rough -in 079146- 503- 201 -5718 N
Corrections /Comments/ Instructions:
PASS ❑ PARTIAL APPROVAL ❑ CANCEL ❑ NO ACCESS
❑ FAIL ❑ CALL FOR INSPECTION ❑ ADDITIONAL FEES ASSESSED
1 12A
Inspector: 1 V l/ Date: 71 lvl / Phone #: (503) 718-
7
_ )
CITY OF TIGARD
BUILDING DIVISION PERMIT #: MFC2008-00543
13125 SW Hall Blvd., Tigard, OR 97223 DATE ISSUED: 11/10/2008
Phone: (503) 639 -4171 1 I
Inspection Requests (24 Hrs.): (503) 639 -4175 .,' . I �..
INSPECTION WORKSHEET FOR DATE: 11/25/2008 TIME: 7:01AM PAGE: 23
SITE ADDRESS: 08050 SW PFAFFLE ST 110 CLASS OF WORK:
SUBDIVISION: PACIFIC CROSSROADS CORP LOT #: TYPE OF USE:
PROJECT NAME: ACCOUNTAX
DESCRIPTION: Installing new rooftop unit. Valuation: $9,800.00
OWNER: ACCOUNTAX, PHONE #: 503.619 -1040
CONTRACTOR: OREGON HEATING & A/C PHONE #: 503 -53 &2953
Inspection Request Scheduled For: Date: 1 Pour Time: pi
1
Code # Inspection Description Confirm # Contact # Mes -_ • : dif i00.0...... --
610 Gas line 078483 -01 503 - 849.8162
Corrections/Comments/Instructions: ?Abgiii
W4S A S
"17kr d ef.
&v1g__ +
1 149
•
•
P .S ❑ P' ` ' L APPROV' ❑ CA-CEL • • ' CESS
VAIL FOR INSPECTION • • DDITIONA " S ASSESSE'
Inspector: _ Date: 1 #C #: (503) 718 y
Y