Report RECEIVED
OFFICE COPY NOV 0 3 2022
CITY OF TIGARD
BUILDING DIVISION
W YAT T
FIRE PROTECTION , INC.
9095 S.W. Burnham
Tigard, OR 97223
FPS
PCC 241 250 -280
15350 SW SEQUOIA PARKWAY
TIGARD, OR 97224 Zlt)
FIRE PROTECTION
EQUIPMENT SUBMITTAL
Worldwide wwwtyco-fire.com
ti,iii
Series TY-FRB, 5.6 K-factor
Upright, Pendent, and Recessed Pendent Sprinklers
Quick Response, Standard Coverage
General NOTICE
The TYCO Series TY-FRB Sprinklers
Description described herein must be installed
and maintained in compliance with Ir
The TYCO Series TY-FRB,5.6 K-factor, this document, as well as with the '- ?' w
Upright (TY313) and Pendent (TY323) applicable standards of the National
Sprinklers described in this data sheet Fire Protection Association,in addition `t'
are quick response,standard coverage, to the standards of any other authori- ,
decorative 3 mm glass bulb-type spray ties having jurisdiction.Failure to do so s .„
sprinklers designed for use in light or may impair the performance of these 7t -= a.
ordinary hazard,commercial occupan- devices. •
cies such
ping malls.as banks, hotels, and shop- The owner is responsible for main-
taining their fire protection system .
The recessed version of the Series and devices in proper operating con-
TY-FRB Pendent Sprinkler, where dition. Contact the installing contrac-
applicable, is intended for use in areas for or product manufacturer with any
with a finished ceiling. This recessed questions.
pendent sprinkler uses one of the
following: �''
Sprinkler �.
• A two-piece Style 15 Recessed
Escutcheon with recessed adjust- Identification �"
mentftup to de t siti mm) from Number (SIN) `
the flush pendent position.
• A two-piece Style 20 Recessed TY313.. .. Upright 5.6K,1/2 in. NPT
Escutcheon with recessed adjust- TY323. ...Pendent 5.6K,1/2 in. NPT
ment up to 1/2 in. (12,7 mm) from
the flush pendent position. Technical
The adjustment provided by the Data Operation
Recessed Escutcheon reduces the
accuracy to which the fixed pipe drops The glass bulb contains a fluid which
to the sprinklers must be cut. Approvals expands when exposed to heat.When
Refer to Table A the rated temperature is reached, the
Intermediate level versions of Series fluid expands sufficiently to shatter the
TY-FRB Sprinklers are described in Maximum Working Pressure lass bulb, allowin the s rink
Technical Data Sheet TFP357. Sprin- 175 psi(12.1 bar) 9 g p ' ter to
kler guards and shields are described 250 psi(17.2 bar)* activate and water to flow.
in Technical Data Sheet TFP7S0. 'The maximum working pressure of 250 psi(17.2 bar) Design
only applies to the listing by Underwriters Laborato-
ries,Inc.(UL).
Discharge Coefficient Criteria
IMPORTANT K=5.6 GPM/psi'/=(80,6 LPM/barY') The TYCO Series TY-FRB,5.6 K-factor,
Refer to Technical Data Sheet Temperature Rating Upright (TY313) and Pendent (TY323)
TFP2300 for warnings pertaining to Refer to Table A Sprinklers are intended for fire protec-
regulatory and health information.
Finishes tion systems designed in accordance
Always refer to Technical Data Sprinkler:Refer to Table B with the standard installation rules
Sheet TFP700 for the `INSTALLER recognized by the applicable Listing or
WARNING" that provides cautions Recessed Escutcheon:White Coated, Approval agency (such as, UL Listing
with respect to handling and instal- Black Coated,Chrome Plated,or Brass is based on the requirements of NFPA
lation of sprinkler systems and corn- Plated 13, and FM Approval is based on the
ponents. Improper handling and Physical Characteristics requirements of FM's Loss Prevention
installation can permanently damage Frame Bronze Data Sheets).Only the Style 15 or Style
a sprinkler system or its compo- Button Brass/Copper 20 Recessed Escutcheon is to be used
nents and cause the sprinkler to fail Sealing Assembly...Stainless Steel w/TEFLON for recessed pendent installations.
to operate in a fire situation or cause Bulb Glass
it to operate prematurely. Compression Screw Bronze
Deflector Bronze
Page 1 of 4 AUGUST 2018 TFP172
TFP172 ,
Page 2 of 4
Components: *Temperature rating is ** Pipe thread connections per ISO 7-1
1 Frame 4 Bulb indicated on Deflector. can be provided on special request.
2 - Button 5 - Compression STYLE 15 or 20
3 - Sealing Screw ESCUTCHEON PLATE 1/2" 7/16'(11,1 mm) RECESSED
Assembly 6 - Deflector* DEFLECTOR* SEATING SURFACE NPT** NOMINAL MAKE-IN ESCUTCHEON
6* 1
......air,...".. -.__. _. I —
dT1���GT�Ht 1
5 'l 7/16"
(11,1 mm)
4 1
NOMINAL 2° 1 (I h
MAKE-IN (50,8 mm) \ /
2 �1 `�gro 2' 1-3/8"
�! (50,8 mm) + (34,9 mm)
3 WRENCH
1 / FLATS
1
T 1/2"NPT** DEFLECTOR* -..— 2-7/8"(73,0 mm)DIA. --.--
CROSS SECTION UPRIGHT PENDENT RECESSED PENDENT
FIGURE 1
SERIES TY-FRB UPRIGHT(TY313)AND PENDENT(TY323)SPRINKLERS
5.6 K-FACTOR, 1/2 INCH NPT, QUICK RESPONSE
el Installation Step 2. With pipe-thread sealant
applied to the pipe threads, hand-
The TYCO Series TY-FRB,5.6 K-factor, tighten the sprinkler into the sprinkler
RENCH RECESS W hand-
. (TY313) and Pendent (TY323) fitting.
(USE ONLY Sprinklers must be installed in accor- Step 3. Tighten the sprinkler into the
END"A") dance with this section. sprinkler fitting using only the W-Type
General Instructions 6 Sprinkler Wrench(Figure 2).With ref-
erence to Figure 1,apply the W-Type 6
FIGURE 2 Do not install any y Sprinkler Wrench to the wrench flats.
W-TYPE 6 kler if the bulb is cracked or there is Torque sprinklers 7 to 14 lb-ft (9,5 to
SPRINKLER WRENCH a loss of liquid from the bulb.With the 19,0 N•m).
sprinkler held horizontally, a small air
bubble should be present. The diem- Recessed Pendent Sprinklers
WRENCH eter of the air bubble is approximately The Series TY-FRB Recessed Pendent
RECESS 1/16 in.(1,6 mm)for the 135°F(57°C)and Sprinklers must be installed in accor-
3/32 in. (2,4 mm)for the 286°F(141°C) dance with the following instructions.
temperature ratings. Step A. After installing the Style 15
A leak-tight 1/2 in. NPT sprinkler joint or Style 20 Mounting Plate over the
should be obtained by applying a sprinkler threads,and with pipe-thread
minimum to maximum torque of 7 to sealant applied to the pipe threads,
.,
r
414 lb-ft(9,5 to 19,0 N•m).Higher levels hand-tighten the sprinkler into the
of torque can distort the sprinkler Inlet sprinkler fitting.
%wowith consequent leakage or impairment Step B. Tighten the sprinkler into the
PUSH WRENCH of the sprinkler.
IN TO ENSURE sprinkler fitting using only the W-Type
ENGAGEMENT Do not attempt to compensate for 7 Recessed Sprinkler Wrench (Figure
WITH SPRINKLER insufficient adjustment in the Escutch- 3).With reference to Figure 1,apply the
WRENCHING AREA eon Plate by under- or over-tightening W-Type 7 Recessed Sprinkler Wrench
the sprinkler. Re-adjust the position of to the sprinkler wrench flats. Torque
FIGURE 3 the sprinkler fitting to suit. sprinklers 7 to 14 lb-ft(9,5 to 19,0 N•m).
PPRYPEINK 7 RECESSED Upright and Pendent Sprinklers Step C. After ceiling installation and
SRfNKLER WRENCH The Series TY-FRB Upright and finishing, slide on the Style 15 or Style
Pendent Sprinklers must be installed 20 Closure over the Series TY-FRB
in accordance with the following Sprinkler and push the Closure over the
instructions. Mounting Plate until its flange comes in
Step 1.Install Pendent sprinklers in the contact with the ceiling.
pendent position. Install upright sprin-
klers in the upright position.
TFP172
Page 3 of 4
Care and 2-7/8"DIA.
Maintenance i (73,0 mm)
2-1/4" DIA.
The TYCO Series TY-FRB,5.6 K-factor, FACE OF (57,2 mm)
Upright (TY313) and Pendent (TY323) SPRINKLER
Sprinklers must be maintained and ser- FITTING 5/8"(15,9 mm)
+
viced in accordance with this section. \ __ 1 FLUSH
Before closing a fire protection system 3/8±5/16" � � I
main control valve for maintenance (9,5±7,9 mm) //71 stii ,r
work on the fire protection system f /
that it controls, obtain permission to IN 1/8" J
shut down the affected fire protection MOUNTING
systems from the proper authorities SURFACE (3,2 mm)
and notify all personnel who may be CLOSURE SERIES MOUNTING 1-3/8°(34,9 mm)
affected by this action. TY-FRB PLATE
3/4"(19,1 mm)
Absence of the outer piece of an FIGURE 4
a clearance escutcheon, which is ed to cover SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY Y323)
hole, cann deulay sprinkler WITH TWO PIECE 5/8 INCH TOTAL ADJUSTMENT STYLE 15 operation in a fire situation. RECESSED ESCUTCHEON
The owner must assure that the sprin-
klers are not used for hanging any
objects and that the sprinklers are only 2-7/8"DIA.
cleaned by means of gently dusting (73,0 mm)
with a feather duster; otherwise, non- FACE OF
operation in the event of a fire or inad- SPRINKLER 2-1/4"DIA.
vertent operation may result. FITTING (57,2 mm)
Sprinklers which are found to be 5/16±1/4"
leaking or exhibiting visible signs of (7,9±6,4 mm) 1/2"(12,7 mm)
corrosion must be replaced. FLUSH
Automatic sprinklers must never be 7+ �1 ,�
painted,, plated, leaving Y ��� I
coated, or other-
wise altered afterthe factory.
Modified sprinklers must be replaced. MOUNTING 1/8"
Sprinklers that have been exposed to SURFACE I (3,2 mm)
corrosive products of combustion, but
have not operated,should be replaced �`
if they cannot be completely cleaned CLOSURE SERIES MOUNTING 1-3/8"(34,9 mm)
by wiping the sprinkler with a cloth or TY-FRB PLATE 7/8"(22,2 mm)
by brushing it with a soft bristle brush. FIGURE 5
Care must be exercised to avoid SERIES TY-FRB RECESSED PENDENT SPRINKLER ASSEMBLY(TY323)
damage to the sprinklers before, WITH TWO PIECE 1/2 INCH TOTAL ADJUSTMENT STYLE 20
during, and after installation. Sprin- RECESSED ESCUTCHEON
klers damaged by dropping, striking,
wrench twist/slippage,or the like,must Recessed Escutcheon
be replaced. Also, replace any sprin- Limited Specify: Style 15 Recessed Escutch-
kler that has a cracked bulb or that has eon with(specify*)finish,P/N(specify*)
lost liquid from its bulb. (Ref. Installa- Warranty Specify: St le 20 Recessed scutch-
tion Section.) Y
For warranty terms and conditions,visit eon with(specify')finish,P/N(specify*)
The owner is responsible for the www.tyco-fire.com. Refer to Technical Data Sheet TFP770
inspection,testing,and maintenance of
their fire protection system and devices Ordering Sprinkler Wrench
in compliance with this document, as Specify: W-Type 6 Sprinkler Wrench,
well as with the applicable standards Procedure P/N 56-000-6-387
of the National Fire Protection Asso- Specify: W-Type 7 Sprinkler Wrench,
ciation (e.g., NFPA 25), in addition to Contact your local distributor for avail- P/N 56-850-4-001
the standards of any other authorities ability.When placing an order,indicate
having jurisdiction. Contact the install- the full product name and Part Number
ing contractor or product manufacturer (P/N)
with any questions.
Sprinkler Assemblies with NPT
Automatic sprinkler systems are rec- Thread Connections
ommended to be inspected, tested, Specify: Series TY-FRB Upright or
and maintained by a qualified Inspec- Pendent (specify) Sprinkler, SIN
tion Service in accordance with local (specify), K=5.6, Quick Response,
requirements and/or national codes. (specify) temperature rating, (specify)
finish,P/N (specify, refer to Table A).
TFP172
Page 4 of 4
SPRINKLER FINISH(See Note 7)
K TYPE TEMPERATURE BULB LIQUID NATURAL CHROME POLYESTERO
FACTOR COLOR BRASS PLATED
135°F(57°C) Orange
UPRIGHT 155°F(68°C) Red
(TY313)
and 175°F(79°C) Yellow 1,2,3,4,5,6
PENDENT(TY323) 200°F(93°C) Green
5.6 286°F(141°C) Blue
1/2 in.NPT
135°F(57°C) Orange
RECESSED )PENDENT (155°F 68°C Red
(TY323) 1,2,3,4
Figures 4a and 5b 175°F(79°C) Yellow
200°F(93°C) Green
Notes:
1. Listed by Underwriters Laboratories,Inc..(UL)as Quick Response Sprinklers.
2. Listed by Underwriters Laboratories.Inc.,for use in Canada(C-UL)as Quick Response Sprinklers.
3. Approved by Factory Mutual Research Corporation(FM)as Quick Response Sprinklers.
4. Approved by the Gity of New York under MEA 354-01-E.
5. VdS Approved(For details,contact Johnson Controls,Enschede,Netherlands.Tel.31-53-426-4444/Fax 31-54-426-3377.)
6. Approved by the Loss Prevention Certification Board(LPCB Ref.No.094a/06)as Quick Response Sprinklers.
7. Where Polyester Coated Sprinklers are noted to be UL and C-UL Listed,the sprinklers are UL and C-UL Listed as Corrosion-Resistant Sprinklers.
a. Installed with Style 15(1/2 in.NPT)5/8 in.Total Adjustment Recessed Escutcheon,as applicable.
b. Installed with Style 20(1/2 in.NPT)1/2 in.Total Adjustment Recessed Escutcheon,as applicable.
c. Frame and Deflector only.Listings and approvals apply to color(Special Order).
TABLE A
LABORATORY LISTINGS AND APPROVALS FOR
5.6 K-FACTOR SPRINKLERS
P/Na 77 — XXX — X — XXX
SIN SPRINKLER TEMPERATURE
FINISH RATINGS
370 5.6K UPRIGHT(1/2 in.NPT) TY313 1 NATURAL BRASS 135 135°F(57°C)
•
371 5.6K PENDENT(1/2 in.NPT) TY323 3 PURE WHITE(RAL9010)a 155 155°F(68°C)
POLYESTER
•
Notes: SIGNAL WHITE(RAL9003)
a. Use suffix"I'for ISO 7-1 connection;for example, 4 POLYESTER 175 175°F(79°C)
77-370-4-175-I
5 JET BLACK(RAL9005) 200 200°F(93°C)
POLYESTER
9 CHROME PLATED 286 286°F(141°C)
Notes:
a. Eastern Hemisphere sales only
TABLE B
SERIES TY-FRB UPRIGHT AND PENDENT SPRINKLERS
PART NUMBER SELECTION
1400 Pennbrook Parkway,Lansdale,PA 19446 I Telephone+1-215-362-0700 �a 'AS
NATIONAL
O Eeta Johnson Controls.Nl rights reserved.MI specifications and other infame a m tien shown were current as document revision date and are subject to change without notice. Johnson �
' +I
NATIONAL ORE PROTECTION ASSOCIATION and WPC an mestered trademarks of National Ere Protection Ase°clet°n: Controls
TEFLON is a register.red e trademark of DuPont
Eddythread 40
A Lightweight Schedule 40 Replacement Pipe
That Has a Corrosion Resistance Ratio of 1 .0
Bull Moose Tube Company has been making pipe for a long time and is recognized as a producer of quality pipe
products. Eddythread 40 is designed with the same thoroughness as our other fine pipe products and now our
customers have an option to buy a carefully designed replacement for Schedule 40 that:
• Has a Corrosion Resistance Ratio of 1.0
• Has a Pressure Rating of 300 psi
• Is Lighter Weight Than Schedule 40
• Is Approved by Factory Mutual and Listed by Underwriters Laboratories
• Is Produced in Accordance to ASTM A-135 and A-795
• Can be Used With Standard Schedule 40 Threaded Fittings,
Couplings and Valves
• Is Produced From Steel With Excellent Properties of
Strength and Threadability
• Can be Used in Wet, Dry, Preaction, and Deluge Type Sprinkler Systems*
• Offers Lower Freight Costs
EDDYTHREAD 40 SPECIFICATIONS
NOMINAL P e,SIZE (in) WEIGHT.-68/ft) ME BUNS :. SIZE .y
1 1.461 1.083 70
1 1/4 2.070 1.418 51
1 1/2 2.547 1.654 44
2 3.308 2.123 30
CORROSION RESISTANCE RATIOS
NOMINAL PIPE SIZE(In) SCHEDULE 40 EDDYTHREAD 40
1 1.00 1.00
1 1/4 1.00 1.00
1 1/2 1.00 1.00
2 1.00 1.00
'Eddythread 40 can be hot dipped galvanized to meet FM's requirement for dry systems
1819 Clarkson Road For additional information, ll� us w
n Chesterfield,MO 63017 contact your salesperson today at cAW
V BULL MOOSE TUBE COMPANY (800)325-4467 (800)325-4467 or(636)537-2600 LISTED
FAX:(636)537-2645 in the USA,or from Canada
www.bullmoosetube.com call(800)882-4666 40>
A CCRPRRO company e-mail:sales(a butlmoosetube.com
APPROVED
All information contained herein is accurate es known at the tree of publication. Bull Moose Tube reserves the right to change product specifications without notice and without incurring obligation.
8/08
Ductile Iron Threaded Fittings
•
x. '
yg J sL._ �.J'S 5F' q fi n
gy i iF 5.
D /1
f
t
�� 4T
S MITJS , C oc Ji 11 A i
INTERNATIONAL
Ductile Iron Threaded Fittings
Specifications
• <0 branded ductile iron threaded fittings are UL Listed and FM Approved at 500 psi
• Rated to 300 WSP
C (1US
• Ductile iron castings conform to ASTM A536 LISTED
• Fitting dimensions conform to ASME B16.3
• Bushings and plugs conform to ASME B16.14
• Fittings are 100% air tested APPROVED
• NPT threads on all fittings conform to ASME B1.20.1
• Independent lab verification that fittings meet applicable chemical &physical properties
• Manufacturing facilities are ISO 9001:2008 and ISO 14001
Temperature Working Pressure, Nonshock psiG
Degrees F 300# Class Threaded Fittings
-20 to 100 500
150 500
200 480
250 460
300 440
350 420
400 400
450 380
500 360
550 340
600 320
650 300
T I ucti e ron 'flings- ass . I I 1 /
c0US
APPROVED
LISTED
Fig. 35E 3- 90°Elbow
,- A Size part Number A Packing Weight
1°�°'�.4. in in Inner Master Ib
___BRA 1/2 35E 3004 1.13 100 200 0.2
��j 3/4 35E 3D06 1.31 70 140 0.3
A 1 35E 3010 1.50 40 80 0.5
/612
q16 1-1/4 35E 3012 1.75 25 50 0.8
1-1/2 35E 3014 1.94 18 36 1.1
2 35E 3020 2.25 10 20 1.8
2-1/2 35E 3024 2.70 4 8 32
Fig. 35RE3- 90°Reducing Elbow
B , Size A B Packing Weight
Part Number
vk�,.....% in in in Inner Master lb
1 3,4 x 1/2 35RE3006004 1.20 1.22 80 160 0.3
1 x 1/2 35RE3010004 1.26 1.36 70 140 0.4
1 x3/4 35RE30'0006 1,38 1.45 50 100 0.4
IA
Ip� 1-1/4 x 1/2 358E3012004 1.34 1.53 35 70 0.5
1-1/4 x 3/4 3518E3012006 1.45 1-63 35 70 0.6
1-1/4 x 1 35RE3012010 1.58 1.67 30 60 0.7
1-1/2 x 1/2 3518E3014004 1.52 1.75 30 60 0.6
1-1/2 x 3/4 35RE3014006 1.52 1.75 25 50 0.7
1-1/2 x 1 35RE3014010 ! 1.65, 1.80 20 40 0.8
1-1/2 x 1-1/4 35RE3014012 1.82 1.88 18 36 1.0
2 x 1/2 35RF3D20004 1.60 1.97 18 36 1.0
2 x 3/4 35RE3020006 1.60 1.97 18 36 1.0
2 x 1 3513E3020010 j 1-.73 2.02 16 32 1.2
2 x 1-1/4 35RE3020012 1.90 2.10 12 24 1.3
:1D 2 x 1-1/2 351-E3020014 I 2.02 2.16 10 20 1-5
U 2-1/2x 1-1/2 35RE3024014 2.16 2.51 6 12 2.2
C 2-1/2 x 2 35RE3024020 I 2.39 2.60 6 12 25
1 Fig. 35F 3-45°Elbow
Size Part Number A Packing Weight
f '`A in in Inner Master lb
�, 1r2_ 350 3004 0.88 150 300 0.2
����•�; 3/4 35F 3006 0.98 80 160 0.3
Arr A 135F 3012 1.19 40 80 0.7
•
i�i 1A 1-1 35F 3012 1.29 25 50 0.7
1-1/2 12 35F 3014 1.44 120
0 40 1.0
2 35F3020 1.69 10 20 1.6
2-1/2 35F 3024 1.95 4 8 2.7
Fig. 35T 3- Tee
Size part Number A Packing Weight
in in Inner Master lb
Vail; IA 1/2 351 3004 1.13 80 160 0.3
3/4 351 3006 1.31 30 60 0.5
1
1 50
25
I I 1-1(4 357 3012 1.75 10 20 1.1
A cif A 3 1-1/2 35T 3014 1 94 10 20 1.5
2 35T 3020 2.25 6 12 2.4
2-1/2 3513024 2.70 4 8 4.3
111 SNII 1'II-COOPER INTERNATIONAL, • TOLL FREE 1-8110-766-0076 • FAX(323)890-4-45, • 'MI w.mithcoopeeeoin
Ductile Iron Fittings- Class 300 UL/FM
c ® us 4111>
APPROVED
Fig. 35RT3-Reducing Tee LISTED
__ Size A B C Packing Weight
Ipl In Part Number in in in Inner Master lb
aaa� x I _ C 3/1 1/2 35RT3006004 1.20 1.20 1-22 60 120 0.4
1 x 1/2 358T3010004 1.26 1.26 1.36 30 60 0.6
-��--�-- 1 x 1/2 x 1 35R13010004010 1.50 1.36 1.50 30 60 0-6
1 x 3/4 35RT3010006 1.38 1.38 1.45 25 50 0.6
1 x 3/4 x 3/4 35RT3010006006 1.38 1-31 1.45 35 70 0.6
B A 1 x 3/4 x 1 35RT3010006010 1.50 1.45 1.50 25 50 0.7
.-1/4 x 1/2 35RT3012004 1,34 ! 1.34 1.53 20 40 0-8
1-1/4 x 1/2 x 1-1/4 35RT3012004012 1.75 1.53 1.75 25 50 0.9
1-1/4x3/4 35RT3012006 1.45 145 1.62 15 30 0.9
1-1/4x 3/4 x 1-1/4 35RT3012006012 1,75 1,62 1.75 20 40 1.0
1-i/4 x 1 35813012010 1.58 1.58 1.67 15 30 1.0
1-1/4 x 1 x 1/2 35RT3012010004 1.34 1.26 1.53 25 50 0.7
1-1/4 x 1 x 3/4 35RT3012010006 14-5 538 1.63 20 40 0.8
1-1/4 x 1 x 1 35RT3012010010 1.58 1.50 1.69 20 40 0,9
'-1/4 x 1 x 1-1/4 35RT3012010012 1.75 1-69 1.75 15 30 1,0
1-1/2x 1/2 35RT3014004 1.41 1.41 1.66 16 32 1.0
1-1/2 x 1/2 x 1-1/4 353(3014004012 1-81 1-56 1 88 24 48 1.1
1-1/2 x 1/2 x 1-1/2 35RT3014004014 1.94 1.66 1.94 12 24 1.2
1-1/2x3i4 35RT3014006 1_52 1-52 1.75 16 32 1.1
1-1/2 x 3/4 x 1-1/4 35RT3014006012 1.94 1.66 1.88 20 40 1.1
1-1/2 x 3/4 x 1-1/2 35RT3014006014 1.94 1.75 1.94 18 36 12
1-1/2 x 1 35RT3014010 1.65 1.65 1.80 12 24 1.2
1-1/2 x 1 x 1/2 35RT3014010004 1,44 1.25 1.69 20 40 0.8
1-1/2 x 1 x 3/4 35RT3014010006 1.50 1.44 1.75 16 32 0.9
1-1(2 x 1 x 1 35RT3014010010 1.65 1.50 1.80 16 32 1.0
1-1/2x 1 x 1-1/4 35RT3014010012 1.82 1.67 1.88 12 24 1.2
1-1/2 x 1 x 1-1/2 35RT3014010014 1 94 1.80 1.94 12 24 1 3
1-1/2x 1-1/4 35RT3014012 1.82 1.82 1.88 12 24 1.4 �
1-1,2 x 1-1/4 x 1/2 35813014012004 1.41 1,34 1.66 16 32 0-9
1-1/2 x 1-1/4 x 3/4 35RT3014012006 1.52 1,45 1.75 16 32 1.0
1-1/2 x 1-1/4 x 1 35RT3014012010 1.65 1.58 1.80 16 32 1 1
1-1/2 x 1-1/4 x 1-1/4 35RT3014012012 1.82 1.75 1.88 14 28 1,3
1- 2x1-1/4x1-1/2 35RT3014012014 1.94 1.88 1.94 14 28 1.4
2 x 1/2 35RT3020004 1.49 1.49 1.88 10 20 1.5
2x3,/4 35RT3020006 1.60 1,60 1,97 10 20 1.6
2 x 1 35RT3020010 1.73 1,73 2.02 8 16 1-7
2 x 1 x 2 35RT3020010020 2.25 2,02 2,25 8 16 1.9
2 x 1-1/4 35RT3020012 1.90 1.90 2.10 8 16 1.9
2 x 1-1/4 x 2 35RT3020012020 2.25 2.10 225 8 16 2.0
2 x 1-1/2 35RT3020014 2.02 2.02 I 2.16 8 16 2,1
2x1-1/2x '/7 35013020014004 1.49 1.41 1.88 10 20 1,3
2 x 1-1/2 x 3/4 35RT3020014006 1.60 1.52 1.97 10 20 1,4
2x 1-1/2 x 1 35813020014810 1 73 1-65 202 8 16 1.5
2 x 1-1/2 x 1-1/4 35RT3020014012 1.90 1.82 2.10 8 16 1.7
2 x 1-1/2 x 1-1/2 351-3130200140141 2-02 1-94 2-16 , 8 16 1.8
Fig. 35BT3-Bull Head Tee
Size A B C Packing Weight
n Part Number n in in Inner Masser lb
use T 3/4 x 1 358T3006010 -.45 1.45 1.37 30 60 0.6
h1 x 1-1/4 35813010012 1.67 1.67 1.58 20 40 0.9
1pv...-,...,_,_ 1 x 1-1/2 35RT3010014 1_80 1 1.80 1.0,5 15 30 1_0
A >• B i 1-1/4 x 1 x 1-1/2 358T3012010014 1.88 1.80 1.82 15 30 1.2
1-1/4 x 1-1/2 35[31301201,1 1-88 1 86 1-82 15 3C 1.3
1-1/4 x 2 35BT3012020 2.10 2.10 1.90 10 20 1.6
1 1/2 x 1-1/4 x 2 35BT3014012020 2-16 2.10 2.02 10 I 20 1.8
1-1/2 x 2 35BT3014020 2.16 2,16 2.02 8 16 1,8
5N11'l'l I-COOPIE:R INTFRNAI'1ONAL® • 'lOLL FREE 1-890-766-(1070 • FAX(323)890-4456 • www.smithcooper.com 112
I Ductile Iron Fittings- Class 300 UL/FM
I /eIJ Lr"71'L[O,
C ® US
APPROVED
A
Fig. 35CP3 -Straight Coupling with Ribs LISTED
,, .NI Size Part Number A Packing Weight
in in Inner Master lb
-_- 1/2 35CP3004 1.38 200 400 0.1
0.2
3/4 35CP3006 1.63 100 200
"" �� 35CP3010 75 60 120 0 4
1-1/4 35CP3012 2.00 35 70 0.5
1-1/2 35003014 219 25 50 0,7
2 35CP3020 2.62 15 30 1.2
2-1/2 35003024 3.00 9 18 2.2
Fig. 35RC3 -Hex Reducing Coupling
Size Part Number Packing Weight
illireITM
in lb
A 1 x 1/2
1 x 3/4 356C3010004 1.69 80 160 0.3
•
35RC3010006 1.69 60 120 0.4
��; 1-1/4 x 3/4 35RC3012006 n
206 40 80 0.6
2 x 1 (not hex) 35RC3020010 2 Inner Master 81 20 40 1.0
Fig. 35HB3 -Hex Bushing
_ Size Part Number
B A Packing Weight
' in in Inner Master lb
�._ 1 x,1/2 35HB3010004 1.06 180 360 0.2
A 1 x 3/4 35H63010006 1,06 180 360 I 0.1
1-1/4 x 1 35HB3012010 1.19 90 180 02
,_ 1-1/2 x 1 351-B3014010 125 75 150 0.4
1-1/2 x 1-1/4 35HB301G012 1.25 75 150 0.3
2 x 1 35HB3020010 1.38 40 80 0.6
U 2 x 1-1/4 35HB3020012 1.38 40 80 0.6
C 2 x 1-1/2 35HB3020014 1.38 40 80 0.6
I Fig. 35SP3 -Square Head Plug
E. Size Part Number A Packing Weight
in in Inner Master lb
1/2 35SP3004 0.94 600 1200 0 07
3/4 35SP3006 1.12 350 700 0,1
114;1191 I
1 l A
1 1 35SP3010 1.25 200 400 0.1
1
1-1/4 35SP3012 1.37 100 200 0.3
1-1/2 35SP3014 1.44 80 160 0.4
2 35SP3020 1.50 45 90 0.6
Fig. 35U 3- Union with Brass Seat
� A Size Part Number A Packing Weight
�traism in in___._ _ Inner Master lb ,
1 35U 3010 2.19
20 40 1.0
1-1/4
1-1/2 35U 3012
35U3014 2 50
262 15
10 30
20 1.2
111111
_ 1.7
�. giss 2 35U 3020 3.12 6 12 2.4
ham
113 SNIEFII-COOPER INTERNATIONAL • TOLL FREE 1-800-766-0076 • FAX(323)890-4456 • www.smithcooper.com
,-./: , J ` inch e ron fittings- ass ► I 1
c ® us 440>
APPROVED
Fig. 35X 3— Cross LISTED
E A m A ) Size A Packing Weight
Part Number
in Inner _ Master lb
gaffe! in I 1A 1 35X3010 1,50 20 40 0.9
1 1-1/4 1.75 12 24 1.4
- I 11 A35X 3012
1-1/2 35X 3014 94 8 16 8
2 35X 3020 2.25 6 12 2.8
B B Fig. 35RX3—Reducing Cross
Size A B Packing Weight
Part Number
IT
� lA in ininInner Master Ib
1-1/4 x 1 35RX30120101.67 1 5815301.24111
-1--� 1-1/2 x 1 35RX3014010 1.80 1.65 12 24 1.4
1
I TA 2 x.1 35RX3020010 202 1 73 8 16 2.0
Fig. 35C 3—Cap
Size A Packing Weight
Part Number
in Inner Master lb
®� �A
in 1/2 350 3004 0.87 300 600 0.1
3/4 350 3006 0.97 200 400 0,1
1 1 35C 3010 6 0 220 0.2
1-1/4 35C 3012 1.28 70 140 0.4 ',3, ,
1-1/2 35C3014 1.33 50 100 05
o
2 35C 3020 1.45 25 50 0.8
2-1/2 35C 3024 1.70 18 36 1 6 '. .
Fig. 35BC3—Beam Clamp
01 Size A Packing Weight
n Part Number in Inner Master lb
AIKiu
■ 3i8 358C3003 0.75 0C 200 0.3
.� 1/2 35BC3004 0.75 80 160 0.5
S\II'I'I I-COOPER INTERNATIONAL® • TOLL FREE 1-800-766-0076 • FAX(.333)890-4456 • www.smithcoopeccom 114
411111.1111111111.11111=1.1
1
can FM (vs� LPCB
a9T"�_7
SEE VICTAULIC PUBLICATION 10.01 FOR DETAILS
STYLE 922 - --—
The Style 922 Outlet-T prov.des a convenient method of incorporating',3,and 1715,20
and 25mm outlets for directly connecting sprinklers,drop nipples,sprigs,gauges,drains and
other outlet products.Available for 13/4 through 76.1 mm/32 to 76.1 mm piping systems,Style
922 outlets are UL/ULC Listed, LPCB and FM Approved for branch connections and VdS
Approved for direct sprinkler connection only on wet and dry systems.
The locating collar engages into the hole prepared in the pipe.When tightened,the assembly
compresses the gasket onto the 0D of the pipe.The Style 922 Outlet-T is UL/FM rated up
to 300 psi/2068kPa and VdS rated up to 16bar at the ambient temperatures typical for fire
protection systems.
Style 922 is suitable for use on standard,lightwall,Schedule 5 and other specialty pipes.*
Contact Victaulic for other optional coatings.
*Consult Section 10.01 for specific listings/approvals.
MATERIAL SPECIFICATIONS Housing:Ductile iron conforming to ASTM A-536,grade 65-45-12. Ductile iron conforming to
ASTM A-395,grade 65-45-15,is available upon special request.
Gasket:
• Grade"E"EPDM •Type A
(Violet color code). FireLock products have been Listed by Underwriters Laboratories Inc.and •
Approved by Factory Mutual Research for wet and dry(oil free air)sprinkler services up to the
rated working pressure using the Grade"E"Type A Gasket System.
Bolts/Nuts:Heat-treated plated carbon steel,trackhead meeting the physical and chemical
requirements of ASTM A-449 and physical requirements of ASTM A-183.
Housing Coating:
• Orange enamel(North America,Latin America,Asia Pacific)
• Red enamel(Europe) •
•
JOB/OWNER CONTRACTOR ENGINEER
System No. Submitted By Spec Sect Para
Location Date Approved
Date
www.victaulic.com
VICTAJLIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.®2009 VICTAULIC COMPANY.ALL RIGHTS RESERVED. ICtc1l-I lIC.
REV G
IPS CARBON STEEL PIPE- HOLE CUT PRODUCTS 10.52
it Lock tI t-T
STYLE 922
DIMENSIONS Nominal Size Hole App,
inches/mm Diameter Dimensions inches/millimeters Weight Ed di
FPTt` I 0.001 0.0 i T. V W Y 2 Ibs 1
III 1 Y. 13/16 1.30 183 21 70 3 87 2.56 1 0
V .. I I 32 X ,..__IS 30/1 330 46.5 279 98.3 65.0 045
VY
111111k . 8a 13/16 L28 1.83 1.10 3.87 2.56 1.1
I ` 20 302 325 46.5 279 98.3 65.0 0.50
n ni r�s
�., Rr W 1 i) 1 3/16 152 2.18 1.10 3.87 2.56 1.2
INA 25 30.2 38.6 554 279 983 650 054
15 Yz 13/16 1.42 1.95 1.22 408 2.56 12
40 X 15 30.2 36.1 49 5 31.0 103.6 65 0 0.54
-� _ __
3 13/16 140 195 1.22 4.08 256 1.2
20 30.2 35 6 49.5 31.0 103.6 65.0 0.54
1 1 3/16 164 2.30 1.22 4.08 2.56 1.3
25 30.2 41.7 58.4 31.0 103.6 65.0 0.59
2 /__. 13/16 166 2.19 146 4.60 2.56 1.3
50 x 15 30.2 42.2 55.6 3/1 1168 65.0 059
Kr 13/16 1.64 2.19 1.46 460 2.56 14
20 302 41.7 556 371 1168 65.0 0.64
_.. . 1 3/16 1 88 2.54 1 46 4 60 2.56 1.5
25 302 478 64.5 37.1 116.8 65.0 0.68
21/2 Vr 13/16 I91 244 171 5.40 2.56 1 6
65 X 15 30.2 48.5 62.0 434 137.2 65.0 073
/ 13/16 1.89 2 44 1.71 5 40 2.56 1 6
20 30.2 48.0 62.0 434 1372 65.0 0.73
1 13/16 2.13 279 171 540 2.56 1.6
25 302 54.1 709 434 1372 65.0 0.73
76.1 min X Kr 13/16 191 244 171 5.50 2.56 - 16
r 15 30.2 48.5 62.0 43.4 139.7 65.0 0.73
_... / 13/16 1.89 244 1.71 5.50 256 1.6
_ 20_ 30.2 48.0 620 434 139.7 650 0.73
1 13/16 2.13 2.79 1.71 550 2.56 17
25 30.2 541 70.9 43.4 139.7 65.0 0.80
t Victaulic female threaded products are designed to accommodate standard NPT or BSPT(optional)
male pipe threads only.Use of male threaded products with special features,such as probes,dry pen-
dent sprinklers,etc.,should be verified as suitable for use with this Victaulic product.Failure tc verify
suitability in advance may result in assembly problems or leakage.
`Center of run to engaged pipe end for NPT threads(dimensions are approximate).
•
www.victaulic.com
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY.0 2009 VICTAULIC COMPANY.ALL RIGHTS RESERVED. .Ct'auIiC.
10.52_2
IPS CARBON STEEL PIPE- HOLE CUT PRODUCTS 10.52
tr o ® Ou U uT
STYLE 922
PERFORMANCE
Equ.va icrt Length of 1 inch
Schedule 40 Steel Pipe(per ell_
Run Size r Outlet 3iee 213 Sectmn 1611C-120P_I T
Inches/mm Feet/meters
1 Vu X 1 8.5
32 25 2.6
11/2 X 1 8.5
40 25 . 2.6
2 X 1 8.5
50 25 2.6
2Yx X 1 8.5
65 25 2.6
76.1 mm X 85
25 2.6
*Hazen-Williams coefficient of friction is 120
www.victaulic.com
ICta Vls♦r
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY,C 2009 VICTAULIC COMPANY.ALL RIGHTS RESERVED.
REV O
IPS CARBON STEEL PIPE- HOLE CUT PRODUCTS (/'�/
t - a,R ��M��x
FireLock® Outlet-T
STYLE 922
INSTALLATION Reference should always be made to the 1-100 Victaulic Field Installation Handbook for the product
you are installing. Handbooks are included with each shipment of Victaulic products for complete
installation and assembly data,and are available in PDF format on our website at www-victaulic.com.
WARRANTY Refer to the Warranty section of the current Price List or contact Victaulic for details.
NOTE This product shall be manufactured by Victaulic or to Victaulic specifications.All products to be
Installed in accordance with current Victaulic installation/assembly instructions.Victaulic reserves the
right to change product specifications,designs and standard equipment without notice and without
incurring obligations.
For complete contact information,visit www-victaulic.com
10.52 3355 REV G UPDATED 12/2009 •ct uIEC
VICTAULIC IS A REGISTERED TRADEMARK OF VICTAULIC COMPANY,02009 VICTAULIC COMPANY.ALL RIGHTS RESERVED.
10.52
Pipe Hangers
Fig. 200 - "Trimline" Adjustable Band Hanger (B-Line Fig. B3170NF) ®TOLCO
Fig. 200F - "Trimline" Adjustable Band Hanger with Felt Lining (B-Line Fig. 8317ONFF► G UL)us
Fig. 200C - "Trimline" Adjustable Band Hanger with Plastic Coated (B-Line Fig.B3170NFC) tlst1=o
Fig. 200S - "Trimline" Adjustable Band Hanger with Non-Captured Nut
41>
Size Range:
Fig. 200 - 1/2" 115mm)thru 8" (200mm) pipe
Material: Steel, Pre-Galvanized to G90 specifications
Function: For fire sprinkler and other general piping purposes. Knurled
swivel nut design permits hanger adjustment after installation.
Features: f I
• (1/2" n 5mml thru 2" 150mm1) Flared edges ease installation for all pipe
types and protect CPVC plastic pipe from abrasion. Captured design
keeps adjusting nut from separating with hanger. Hanger is easily 41 f B
installed around pipe. `®'
A
For hanger with non-captured nut order Fig. 200S.
• (21/2" 165mm)thru 8" (200mm)) Spring tension on nut holds it securely in / f
hanger before installation. Adjusting nut is easily removed.
Approvals: Underwriters Laboratories listed (1/2" (15mm)thru 8" (20omm1) \ rig.208-Vz.200-3/4
in the USA(UL)and Canada (cUL)for steel and CPVC plastic pipe and 1
Factory Mutual Engineering Approved (FM) (3/4" (20mm)thru 8" (200mm0. Fig.200-1 to 200-2 Fig.200-21/2 to 200-8
Conforms to Federal Specifications WW-H-171 E &A-A-1192A, Type 10
and Manufacturers Standardization Society ANSI/MSS SP-69&SP-58, .,.,,,
Type 10.
Maximum Temperature: 650°F(343°C) sere
Finish: Pre-Galvanized. Stainless Steel
materials will be supplied with (2) hex nuts 4„ s
in place of a knurl nut. _
Order By: Figure number and pipe size ,.
Designed to meet or exceed requirements of yr, 3
FM DS 2-0. iii
100
Fig.200
Fig.200C Fig.200F
Pipe Size Rod Size A B Approx.Wt./100 s
Part No. in. Imml in. Imml in. (mm) lbs. (kg) '- e
200.1/2 1/2" (15) 3/8"-16 31/8" (79.4) 25/8" (66.7) 11 15.01
200--3/4 3/4" (20) 3/13'-16 31/8" (79.4) 21/2" (63.5) 11 (5.01
200-1 1" 125) 3/g"-16 33/e' (85.71 25/8" 166.7) 12 (5.5)
200-11/4 11/4' (32) 3/e'-16 33/4" (94.01 27/8" 173.01 13 15.9)
200-11/z 11/z" (40) 3/s"-16 37/6" (98.4) 27/e" 173.0) 14 (6.4)
200-2 2" (50) 3/8"-16 41/2" (114.3) 3" 176.3) 15 (6.9) 4'
200-21/z 21/2" (65) 3/a"-16 55/8" (142.9) 41/8" (104.7) 27 (12.3)
200-3 3" (75) 3/8"-16 57/a" (149.1) 4" (101.6) 29 (13.3) Fig.200S
200-31/z 31/2' (901 3/e"-16 73/e" (187.31 51/4" (133.3) 34 (15.6)
200-4 4" 11001 3/8"-16 73/8" (187.3) 5" (127.0) 35 (16.0)
200-5 5" (125) 1/2"-13 91/8" (231.81 . 61/4" (158.71 66 130.2)
200-6 6" (150) 1/2"-13 101/a" (257.2) 63/4" 1171.4) 73 133.4)
200-8 8" (200) 1/2"_13 131/a" (333.41 83/4" 1222.2) 136 (62.3)
At dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified.
Fire Protection Solutions B-Line
21 by Ei•N
Threaded Accessories
B3205 - Threaded Rod (ri ht-hand threads - both ends) TOLCO Fig. 103 �',.
( 9 f g )
B3205L - Threaded Rod (right& left hand threads) - TL lo
Specify Length <
'Size Range: 3/s"-16 thru 3"-4 rod .t. ))
Material: Steel
Function: Recommended for use as a hanger support in hanger assemblies. TL .ill
Rod is threaded on both ends with right hand threads of the length shown.Also
available with left and right hand threads-specify Fig. B3205L when ordering. 1\04 A
Thread Size
Maximum Temperature: 750°F(399°C)
Finish: Plain.Contact B-Line for alternative finishes and materials.
Order By: Part number, rod size, length and finish
Standard Design Load
Thread Size Thread Length TL 650°F(343°C) 750°F(399°C)
Part No. A in. (mm) Lbs. (kN) Lbs. (kN)
83205-3/8x'1' 3/8"-16 21/2" (63.5) 730 (3.25) 572 (2.54)
63205-1/2 x'L' 1/2"-13 21/2" (63.5) 1350 (6.00) 1057 (4.70)
B3205-5/a x'L' 5/8"-11 21i2" (63.5) 2160 (9.61) 1692 (7.52)
63205-3/4 x'L' 3/4"-10 3" (76.2) 3230 (14.37) 2530 (11.25)
B3205-7/8 x'1' 7/9"-9 31/2" (88.9) 4480 (19.93) 3508 (15.60)
83205-1 x'L' 1"-8 4" (101.6) 5900 1 (26.24) 4620 (20.55)
B3205-11/8 x'L' 114"-7 41/2'° (114.3) 7450 (33.14) 5830 (25.93)
53205-11/4x'I.' 11/4"-7 5" (127.0) 9500 (42.25) 7440 (33.09)
63205-11/2x'L' 11/2"-6 6" (152.4) 13800 (61.38) 10807 (4807)
B3205-13/4 x'L' 13/4"-5 7" (177.8) 18600 (82.73) 14566 (64.79)
B3205-2 x'L' 2 41/2 8" (203.2) 24600 (109 42) 19625 (87.29)
B3205-21/4 x'L' 21/4 41/2 9" (228.6) 32300 (143.67) 25295 (112.51)
B3205-21/2 x'1' 21/2"-4 10" (254.0) 39800 (177.03) 31169 1 (138.64)
B3205-23/4 x'L' 23/4'4 11" (279.4) 49400 (219.73) 38687 (172.08)
-,-,.,I's nArtiO:
B3205-3 x'L' 3"-4 12" (304.8) 60100 (267 32) 47066 (209.35)
ATR - All Threaded Rod 120" (3.05m) Lengths (TOLCO Fig. 100)
Fig. 99 - All Threaded Rod Cut To Length
Size Range: 3/a"-16 thru 11/2"-6 rod in 120"(3.05m)lengths or cut to length
Material: Steel _ r��'
Maximum Temperature: 750°F(399°C) �,. \ . `o
Finish: Plain.Contact B-Line for alternative finishes and materials. "� g m
Order By: Part number, rod diameter and finish a
Part No.-Size x Length Threads Recommended Load Approx.Wt./100 Ft.
AIR Fig.99 Per Inch Lbs. (kN) Lbs. (kg)
ATR 1/4"x 120 99-1/4"x length 20 240 (1.07) 12 (5.44)
ATR 3/8"x 120 99-3/8"x length 16 730 (3.24) 29 (13.15)
AIR 1/2"x 120 99-1/2"x length 13 1350 (6.00) 53 (24.04)
ATR 5/a"x 120 99-5/8"x length 11 2160 (9.80) 89 (40.37)
ATR 3/4"x 120 99-3/4"x length 10 3230 (14.37) 123 (55.79)
ATR 7/8"x 120 99-7/8"x length 9 4480
ATR 1"x 120 99-1"x length 8 5900 1 (26.24) 225 (102.06)
All dimensions in charts and on drawings are in inches.Dimensions shown in parentheses are in millimeters unless otherwise specified.
B
Pipe Hangers&Supports 236 Revised 4/28/2014 y b Line
®: 41
VERTICAL MOUNT SAMMYS®
SAMMYS° for Wood
410
Not less than Wood Flooring
2•nominal width Product Features
1 � drlNo pre-drilling required.
I
Notless men Quick
driver.to install using the Sammy
IMP ## 3•nominal Nut Driver with an 18V cordless
thickness(2.112")
(depth or side Wood Joist N
of vertical member)
G t
•Saves time from traditional
Double Sheetrock methods.
For vertical use- Ceiling
install in center of lower face.
•Reduces installation cost.
Minimum 2'embedment into base ".-
material for WAN 13 compliance Composite I Truss
Consult truss marwlactorer far •Made in the U.S.A.
e recommended installation point
' °Pradnllmg may be required for GST
r 25-380.Tool available on page 10.
}
,.F 1.
Approvals Rod Part Model Screw Ultimate UL Test FM Test Box Case
Size Number Descriptions Pullout(Ibs) Load(Ibs) Load(Ibs) Oty Oty
—
1/4" 8002957 GST 100 114 x 1' 210(7116"OSB) 25 125
670(3/4°Ply)
1l4" 8003957 GST 200 1/4 x 2' 1760 (Fir) 25 125
1/4" 8004957 GST 300 1/4 x 3" 2060(Fir) 25 125
318" 8006957 GST.75 114 x 314" 564 (3/4"Ply) 25 125
lig• 3/8" 8007957 GST 10 114 x 1' 210(7/16"OSB) 300 25 125
670(314'Ply) —
il
52-<> 318" 8008957 GST20 114x 2" 1760 (Fir) 850 1475 25 125
ai• 3/8' 8058925 GST 20SS 1/4 x 2° 1760 (Fir) 850 25 125
Q` 3/8" 8009925 GST 25-380 318 x 2-112" 2113 (Fir) 1500 25 125
*X-Q 3/8' 8010957 GST 30 114 x 3" 2060(Fir) 1500 1475 25 125 #14 Black
Nut Driver
3/8" 8069925 GST 30-SS 114 x 3" 2060 (Fir) 25 125 Pad#8113910
3B° 8011925 GST40 1/4 x4' 2180(Fir) 25 125
3/8" 8012925 GST 60 1/4 x 6" 2230 (Fir) 25 125 _
12" 8013925 GST 2 114 x 2' 1760(Fir) 25 125
1/2" 8014925 GST 2.5-380 3/8 x 2-1/2" 2113 (Fir) 25 125
12° 8015925 GST 3 1/4 x 3' 2275(Fir) 25 125 —
1/2" 8016925 GST 4 114 x4" 2180(Fir) 25 125
12' 8017925 GST 6 1/4 x 6" 2230(Fir) 25 125 — #14 SW Red
Nut Driver
Part#8114910
SAMMY Swivel Head® for Wood
Product Features
•Eliminates distortion of threaded rod. •Saves time from traditional methods.
•Accommodates up to 3 A"x 12 pitch roof. •Reduces installation cost.
I*
Allows 17°deflection from vertical. Made in the U.S.A.
Approvals Rod Part Model Screw Ultimate UL Test FM Test Min Box Case
Size Number Descriptions Pullout(Ibs) Load(Ibs) Load(Ibs) Thickness Qty Qty
+� 3!8" 8139957 SN-GST 2O N4 x 2" 1257(Fir) 1050 1475 25 125 125
3/8" 8141957 SH-GST 30 114 x 3" 1720(Fir) 1500 1475 25 125
#14 Black
Nut Driver
SPECIAL NUT DRIVER SYSTEM:The nut drivers were designed with a unique spin-off feature which provides a fast and safe installation each lime.When the face of the driver comes into Part#8113910
contact with the material you are installing into,continue drilling until nut driver spins free.Installation is then complete.Warranty requires the use of the appropriate nut driver for installations.
For the most up to date information,visit www.sammysuperscrew.com 4 .