Report (5) Oregon Residential Specialty Code N1107.2
HIGH-EFFICIENCY INTERIOR LIGHTING SYSTEMS
Permit No.: As-c. ket_ 9.a."2 Jurisdiction.
•
Site Address: kul 9..33 SZ \
subdivisionfut#:
and/or
Map and Tax Lot#:
By my signature below, I certify that a minimum of fifty(50)percent of the permanently
installed lighting fixtures in the above mentioned building have been installed with compact or
linear fluorescent, or a lighting source that has a minimum efficacy of 40 lumens per input watt.
(Oregon Residential Specialty Code N1107.2)1
Signature: Date: LA. / SI 0-Z
tractor/Autc-oriled Agent
Print Name:
ORSC Section N1107.2.High-efficiency interior lighting systems. A minimum of fifty(50)percent o the
permanently installed lighting fixtures shall be installed with compact or linear fluorescent,or a lighting source that
has a minimum efficacy of 40 lumens per input watt. Screw-in compact fluorescent lamps comply with this
requirement.
The building official shall be notified in writing at the final inspection that a minimum of fifty percent of the
permanently installed lighting fixtures are compact or linriir fluorescent,or a minimum efficacy of 40 lumens per
input watt.
I:\BuildineForms\RES-HighEfticieacyLighting.doc 07/01/08
Oregon Residential Specialty Code R408.1
MOISTURE BARRIER ACKNOWLEDGEMENT FORM
, am the general contractor or the owner-builder
at the following address:
Site Address: I 1-k3
City:
Permit#: ocDp.
Subdivision/Lot#: Las
and/or
Map and Tax Lot#:
To conform with the 2014 Oregon Residential Specialty Code(ORSC), Section R408.1
Ventilation. I am notifying the building official that I have installed the Moisture Barrier as per
Requirement in ORSC Section 408.1 and have taken the following steps to meet this code
requirement:
R4--The ground surface of the under-floor space is covered with 6-mil black polyethylene
sheeting with
D‘ints lapped 12"at seams and
REX-i-ending up the foundation walls 12".
Signatur0: Date: WI
Gxthcgr or Owner-Builder
1:1BuildingWorm1RES-MoistureEtarriendoc 09/13/2016
Oregon Residential Specialty Code R318.2
MOISTURE CONTENT ACKNOWLEDGEMENT FORM
I, am the general contractor or the owner-builder
at the following address:
Site Address-
. 11—t IL12.CA.-111' A-0-e--
City.
Permit#:
\q— 009-•
Subdivision/Lot#: 3
and/or
Map and Tax Lot#:
To conform with the 2008 Oregon Residential Specialty Code(ORSC), Section R318.2 and
OAR 918-480-0140, I am notifying the building official that I am aware of the moisture content
Requirement of ORSC Section R318.2 and have taken steps to meet this code requirement.
[Section R318.2 is provided for reference].
R3I8.2 Moisture Content: Prior to the installation of interior finishes, the building
official shall be notified in writing by the general contractor that all moisture-sensitive
wood framing members used in construction have a moisture content of not more than 19
percent by dry weight of dry framing members.
4„ I
Signa e: Date: (-(2/1 (9`•°
cto or Owner-Builder
I:\Buildinfform\RES-MoistureSensitiveWood.doc 0925/98
Moffet Energy Modeling
CCB#223372
Phone: 916-342-0742
tyler@moffetco.com
Blower Door Test Affidavit
Permit#: Builder: Taylor Morrison
Site Address: Roshak Lot 63: 14233 SW 169th Ave,Tigard, OR 97224
Conditioned Floor Area (sq.ft.): 1554
Source: Calculated from plans Calculated Building Volume (cubic feet): 14970
TEST RESULTS: 1020 CFM @ 50 Pa
ACH @ 50 Pa = {(CFM x 60)_Volume}: 4.09
Ring: Open oA B
Minneapolis Blower Door and DG 700 Manometer
I certify that these building leakage rates are accurate and determined using standard BPI testing
protocol.
Company Name: Moffet Energy Modeling Technician: Tyler Moffet
Technician Signature: r- Date: 6/12/2020