Report (5) - .-------------- •",..0 •"
Oregon Residential Specialty Code N1107.2
HIGH-EFFICIENCY INTERIOR LIGHTING SYSTEMS
Permit No.:
(LD ThOLI4L0 Jurisdiction:
I ,‘
Site Address: Lo
Subdivision/Lot#: s
and/or
Map and Tax Lot#:
By my signature below, I certify that a minimum of fifty(50)percent of the permanently
installed lighting fixtures in the above mentioned building have been installed with compact or
linear fluorescent, or a lighting source that has a minimum efficacy of 40 lumens per input watt.
(Oregon Residential Specialty Code Nil 07.2)1
Signature:
Date: CA/I S /).-40
tractor/Authoriied Agent
Print Name:
'ORSC Section N1107.2.High-efficiency interior lighting systems. A minimum of fifty(50)percent o the
permanently installed lighting fixtures shall be installed with compact or linear fluorescent,or a lighting source that
has a minimum efficacy of 40 lumens per input watt. Screw-in compact fluorescent lamps comply with this
requirement.
The building official shall be notified in writing at the final inspection that a minimum of fifty percent of the
permanently installed lighting fixtures are compact or linear fluorescent,or a minimum efficacy of 40 lumens per
input watt
\BuilclineForms\RES-HighEfficiencyLighting.doc 07/01/08
.. ,,, ....... .......... ........ ... .
Oregon Residential Specialty Code R408.1
MOISTURE BARRIER ACKNOWLEDGEMENT FORM
1.71'4-a,k S , am the general contractor or the owner-builder
at the following address:
Site Address:
tut ,)-• t S\-3 tUCATI"
City:
t
Permit#:
ek OOLQ
-
Subdivision/Lot#: Lt.
and/or
Map and Tax Lot#:
To conform with the 2014 Oregon Residential Specialty Code(ORSC), Section R408.1
Ventilation. I am notifying the building official that I have installed the Moisture Barrier as per
Requirement in ORSC Section 408.1 and have taken the following steps to meet this code
requirement:
The ground surface of the under-floor space is covered with 6-mil black polyethylene
sheeting with
[ lits lapped 12"at seams and
[--- -ending up the foundation walls 12".
Signature: Date: (PP S /09.0
or Owner-Builder
IABuildingWorm‘RES-MoistureBarrier.doc 09/13/2016
Oregon Residential Specialty Code R318.2
MOISTURE CONTENT ACKNOWLEDGEMENT FORM
;•.\,(a,A,AA,S , am the general contractor or the owner-builder
at the following address:
Site Address: ILI
City:
Permit#:
t'AST -C)kq-Subdivision/Lot#: La s-
and/or
Map and Tax Lot#:
To conform with the 2008 Oregon Residential Specialty Code(ORSC), Section R318.2 and
OAR 918-480-0140, I am notifying the building official that I am aware of the moisture content
Requirement of ORSC Section R318.2 and have taken steps to meet this code requirement.
[Section R318.2 is provided for reference].
R318.2 Moisture Content: Prior to the installation of interior finishes, the building
official shall be notified in writing by the general contractor that all moisture-sensitive
wood framing members used in construction have a moisture content of not more than 19
percent by dry weight of dry framing members.
Signatu* Date: CP- i/ S19—C)
cto or Owner-Builder
1:\BuildingTorm\RES-MoisnreSensitiveWood.doc 09/25108
Moffet Energy Modeling
CCB#223372
Phone: 916-342-0742
tyler@moffetco.com
Blower Door Test Affidavit
Permit#: Builder: Taylor Morrison
Site Address: Roshak Lot 65: 14241 SW 169th Ave,Tigard, OR 97224
Conditioned Floor Area (sq. ft.): 1554
Source: Calculated from plans Calculated Building Volume (cubic feet): 14970
TEST RESULTS: 988 CFM @ 50 Pa
ACH @ 50 Pa ={(CFM x 60)-Volume}: 3.96
Ring: Open 0 B
Minneapolis Blower Door and DG 700 Manometer
I certify that these building leakage rates are accurate and determined using standard BPI testing
protocol.
Company Name: Moffet Energy Modeling Technician: Tyler Moffet
Technician Signature: Date: 6/12/2020