Permit iiilCITY OF TIGARD MASTER PERMIT
• ' COMMUNITY DEVELOPMENT Permit#: MST2021 00142
13125 SW Hall Blvd.,Tigard OR 97223 503.718.2439 Date Issued: 06/22/2021
T t c;:1 I f� g Parcel: 2S104DA09300
Jurisdiction: Tigard
Site address: 13191 SW RAPTOR PL
Subdivision: QUAIL HOLLOW-WEST Lot: 79
Project: Powell
Project Description: Convert 248 sq ft of rear of garage to living area as bonus room. Trade permits to be pulled
separately.
BUILDING
Floor Areas Required Setbacks Required
Stories: 3 Bedrooms: 0 First: 248 sf Basement: 0 sf Left: 0 Parking Spaces: 0
Height: 0 Bathrooms: 0 Second: 0 sf Garage: 0 sf Front: 0 Smoke
Dwelling Units: 0 Third: 0 sf Right: 0
Detectors: Yes
Total: 248 sf Value: $30,370.08 Rear: 0
PLUMBING
Sinks: 0 Water Closets: 0 Washing Mach: 0 Laundry Trays: 0 Rain Drain: 0 Urinals: 0 1
Lavatories: 0 Dishwashers: 0 Floor Drains: 0 Sewer Lines: 0 SF Rain Storm Sewer: 0
Drains: 0
Tubs/Showers: 0 Garbage Disp: 0 Water Heaters: 0 Water Lines: 0 Catch Basins: 0
Bckflw Prevntr: 0
Footing Drain: 0 Ice Maker: 0 Hose Bib: 0 Backwater Value: 0
Drywell-Trench Drain: 0 Other Fixtures: 0
Other Fixture Units:
MECHANICAL
Fuel Types Air Conditioning: N Vent Fans: 0 Clothes Dryers: 0
Heat Pump: N Hoods: 0 Other Units: 0
Furn<100K: 0 Vents: 0 Woodstoves: 0 Gas Outlets: 0
Furn>=100K: 0
ELECTRICAL
Residential Unit Service Feeder Temp Srvc/Feeders Branch Circuits
1000 sf or less: 0 0-200 amp: 0 0-200 amp: 0 W/Svc or Fdr: 0
Ea add'I 500 sf: 0 201-400 amp: 0 201-400 amp: 0 W/O Svc/Fdr: 0
Mfd Home/Feeder/Svc: 0 401-600 amp: 0 401-600 amp: 0
601-1000 amp: 0 601+amp-1000v: 0
1000+amp/volt 0
ELECTRICAL-RESTRICTED ENERGY
SF Residential
Audio&Stereo: N HVAC: N Security Alarm: N Vaccuum System: N Garage Opener: N All
Other: N Other Description: Ecompasing: N
BUILDING INFO
Class of Work: Type of Use: Type of Constr: Occupancy Group: Square Feet:
ADD SF VB R-3 248
Owner: Contractor:
POWELL,ROD C& RIGGS&MARTIN INC Required Items and Reports(Conditions)
MARGARET B 14200 SE MCLOUGHLIN BLVD STE C
13191 SW RAPTOR PL MILWAUKIE,OR 97267
TIGARD,OR 97223
PHONE: PHONE: 503-650-6786
FAX:
Total Fees: $1,400.68
This permit is issued subject to the regulations contained in the Tigard Municipal Code, State of OR. Specialty Codes and all other applicable law. All work will
be done in accordance with approved plans. This permit will expire if work is not started within 180 days of issuance, or if work is suspended for more the 180
days. ATTENTION: Oregon law requires you to follow the rules adopted by the Oregon Utility Notification Center. Those rules are set forth in OAR
952-001-0010 through OAR 952-001-0090. You may obtain a copy of the rules or direct questions to OUNC by calling 503.232.1987 or 1.800.332.2344.
Issued By: Holly VainiDeWeg'e Permittee Signature: O rt.App Ca t.On
Call 503.639.4175 by 7:00 a.m.for the next available inspection date.
This permit card shall be kept in a conspicuous place on the job site until completion of the project.
Approved plans are required on the job site at the time of each inspection.
f
Building Permit Application -4 13 24
Residential RECEIVE C` FOR OFFICE USE ONE
Cityof Tigard Received I�STZ021 00/LIZ
g e / ZQZ_/ Permit No.:
y 13125 SW Hall Blvd.,Tigard,OR 97223 APR 1. 3 2021 Date/By:
g an Review/ _/'te t-/
II a Phone: 503.718.2439 Fax: 503.598.1960 Date/By: tC(/ Other Permit:
TIGARD Inspection Line: 503.639.4175 CITY OF TIGAAL DateReadyBy: r ® See Page 2 for
Internet: www.ti ard-or. ov Notifi /Method ( SupplementalInformation
g g BUILDING nIVISlt�!�" �-�1
TYPE OF WORK REQUIRED DATA:I-AND 2-FAMILY DWELLING
❑New construction ❑Demolition Permit fees*are based on the value of the work performed.
Indicate the value(rounded to the nearest dollar)of all
®Addition/alteration/replacement 0 Other: equipment,materials,labor,overhead,and the profit for t,Jie
z
a,, cAT G work indicated on this application. 36 37a
-6g"lVVI i "?3?:CONSTRUCTION
® 1-and 2-family dwelling 0 Commercial/industrial Valuation: S
❑Accessory building ❑Multi-family Number of bedrooms:
❑Master builder ❑Other: Number of bathrooms:
� ., JOB SITE. Total number of floors:°NFflRMATIQN:AND LOCATION 3
Job site address: 13191 SW Raptor Place New dwelling area: 248 square feet
City/State/ZIP: Tigard, OR 97223 Garage/carport area: square feet
Suite/bldg./apt.no.: Project name: Powell Garage Conversion Covered porch area: square feet
Cross street/directions to job site: Deck area: square feet
Other structure area: square feet
REQUIRED;DATAk. OMMERCIA ; SE.eiii KI IST
Subdivision: Lot no.: Permit fees*are based on the value of the work performed.
Tax map/parcel no.: Indicate the value(rounded to the nearest dollar)of all
equipment,materials,labor,overhead,and the profit for the
DESCRIPTION OF WORK work indicated on this application.
Convert rear of garage to living area (bonus room). Valuation: $
g .s orf'19- Existing building area: square feet
c((.,,,�� t New building area: square feet
7' � � �7v/r �i��ra� � - /
i O' RTY:' t�. to g'" rr€N
. � � r' Number of stories:
Name: Rod and Margi Powell Type of construction:
Address: Occupancy groups:
City/State/ZIP: Existing:
Phone:( ) Fax:( ) New:
`f,z 0-APPLICANT,-� RWI';' 1d ��AT'PERSON' x BUILDING
P R IT E ' 441, n
,., . `...(Please refer So fee sch'edute r . n.6 ., ,,F'
Business name: Riggs& Martin Structural plan review fee(or deposit): /98
Contact name: Scott Weaver
FLS plan review fee(if applicable):
Address:
City/State/ZIP: Total fees due upon application:
Phone:(503)849-8482 Fax: :( ) Amount received:
PHOTOVOLTA,ICrSOLR iPA L S`Y`STEM TIES*
E-mail: weaver@riggsandmartin.com . :. a ,,,, .. ,
A. .. ..u.N�M,43 -k roof-top mounted PhotoVoltaic Solar Panel tSystem
prescriptive
Business name: Riggs& Martin Submit two(2)sets of roof plan with connection details
and fire department access,along with the 2010 Oregon
Address: 14200 SE McLoughlin Blvd. - Suite C Solar Installation Specialty Code checklist.
City/State/ZIP: Milwaukie, OR 97267 Permit Fee(includes plan review $180.00
and administrative fees):
Phone:(503 ) 849-8482 Fax:( )
State surcharge(12%of permit fee): $21.60
CCB lie.: 109829 L /P,
Total fee due upon application: $201.60
Authorized signature: This permit application expires if a permit is not obtained
1 within 180 days after it has been accepted as complete.
Print name: Scott Weaver Date: 4/9/21 *Fee methodology set by Tri-County Building Industry
Service Board.
I:\Building\Permits\BUP-RESPermitApp.doc 02/24/2011 440-4613T(1 1/02/COM/WEB)
Building Permit Application Checklist
One- and Two-Family Dwelling FOR OFFICE USE ONLY
Cityof Tigard Received
g Date/By: Permit No.:
13125 SW Hall Blvd.,Tigard,OR 97223 Associated permits:
_ Phone: 503.718.2439 Fax: 503.598.1960 F
TIGARD 24-Hour Inspection Line: 503.639.4175 ❑ Electrical ❑ Plumbing El Mechanical
Internet: www.tigard-or.gov ❑ Other:
- THE FOLLOWING ITEMS ARE REQUIRED FOR PLAN REVIEW Yes No N/A
1 Land use actions completed. See jurisdiction criteria for concurrent reviews. ❑ 0 ❑
2 Zoning. Flood plain,solar balance points,seismic soils designation,historic district,etc. 0 0 ❑
3 Verification of approved plat/lot. 0 ❑ ❑
4 Fire district approval required. Name of district: . ❑ ❑ 0
5 Septic system permit or authorization for remodel. Existing system capacity ❑ 0 ❑
6 Sewer permit. ❑ ❑ ❑
7 Water district approval. 0 0 0
8 Soils report. Must carry original applicable stamp and signature on file or with application. ❑ ❑ ❑
9 Erosion control 0 plan 0 permit required. Include drainage-way protection,silt fence design and location of catch- ❑ El ❑
basin protection,etc.
10 3 Complete sets of legible plans. Must be drawn to scale,showing conformance to applicable local and state Er ❑ ❑
building codes. Lateral design details and connections must be incorporated into the plans or on a separate full-size
sheet attached to the plans with cross references between plan location and details. Plan review cannot be completed if
copyright violations exist.
11 Site/plot plan drawn to scale. The plan must show lot and building setback dimensions;property corner elevations(if W-- ❑ ❑
there is more than a 4-ft.elevation differential,plan must show contour lines at 2-ft.intervals);location of easements
and driveway;footprint of structure(including decks);location of wells/septic systems;utility locations;direction
indicator;lot area;building coverage area;percentage of coverage; impervious area;existing structures on site;and
surface drainage.
12 Foundation plan. Show dimensions,anchor bolts,any hold-downs and reinforcing pads,connection details,vent size R ❑ 0
and location.
13 Floor plans. Show all dimensions,room identification,window size,location of smoke detectors,water heater, 0'" 0 0
furnace,ventilation fans,plumbing fixtures,balconies and decks 30 inches above grade,etc.
14 Cross section(s)and details. Show all framing-member sizes and spacing such as floor beams,headers,joists,sub- E 0 0
floor,wall construction,roof construction. More than one cross section may be required to clearly portray
construction. Show details of all wall and roof sheathing,roofing,roof slope,ceiling height,siding material,footings
and foundation,stairs,fireplace construction,thermal insulation,etc.
15 Elevation views. Provide elevations for new construction;minimum of two elevations for additions and remodels. E'" 0 0
Exterior elevations must reflect the actual grade if the change in grade is greater than four foot at building envelope.
Full-size sheet addendums showing foundation elevations with cross references are acceptable.
16 Wall bracing(prescriptive path)and/or lateral analysis plans. Must indicate details and locations;for non- t ❑ ❑
prescriptive path analysis provide specifications and calculations to engineering standards.
17 Floor/roof framing. Provide plans for all floors/roof assemblies,indicating member sizing,spacing,and bearing ❑ 0 0
locations. Show attic ventilation.
18 Basement and retaining walls. Provide cross sections and details showing placement of rebar. For engineered ❑ 0 ❑
systems,see item 22,"Engineer's calculations."
19 Beam calculations. Provide two sets of calculations using current code design values for all beams and multiple joists [r ❑ ❑
over 10 feet long and/or any beam/joist carrying a non-uniform load.
20 Manufactured floor/roof truss design details. 0 0 ❑
21 Energy Code compliance. Identify the prescriptive path or provide calculations. A gas-piping schematic is required 0 0 0
for four or more appliances.
22 Engineer's calculations. When required or provided,(i.e.,shear wall,roof truss)shall be stamped by an engineer or EK—❑ ❑
architect licensed in Ore•on and shall be shown to be applicable to the Iro'ect under review.
JURISDICTIONAL SPECIFICS
23 Three(3)site plans are required for Item 11 above. Site plans must be 8-1/2"x 11"or 11"x 17". ❑ ❑ ❑
24 Two(2)sets each are required for Items 16, 19,20 and 22 above. ❑ El ❑
25 Building plans shall not contain red lines or tape-ons. "Mirrored"building plans will not be accepted. El ❑ El
26 "Reversed"building plans must meet criteria outlined in the Permit&System Development Fees document. ❑ ❑ ❑
27 "Drawn to scale"indicates standard architect or engineer scale. ❑ 0 ❑
28 Site plan to include tree size,type and location per approved project street tree plan(if applicable),and City of Tigard ❑ ❑ ❑
Street Tree List.
29 Site plan to include trees and tree protection measures as required by conditions of approval. Tree locations,driplines, 0 ❑ ❑
and protection measures must be drawn to scale and must include the project arborist's signature of approval.
30 A Clean Water Services'Sensitive Area Pre-Screening Site Assessment form is required for all building additions, ❑ ❑ ❑
including decks,patio covers(over non-impervious surface)and accessory structures to existing residential dwellings
on a lot of record approved prior to September 9, 1995.
I:\Building\Permits\BUP-RESPermitApp.doc 02/24/2011 440-4613T(11/02/COM/WEB)
FOR OFFICE USE ONLY—SITE ADDRESS:
This form is recognized by most building departments in the Tri-County area for transmitting information.
Please complete this form when submitting information for plan review responses and revisions.
This form and the information it provides helps the review process and response to your project.
City of Tigard • COMMUNITY DEVELOPMENT DEPARTMENT
N . Transmittal Letter
T i A it F) 13125 SW Hall Blvd. • Tigard, Oregon 97223 • 503.718.2439 • www.tigard-or.gov
TO: Tigard Building Permit Department/Allyson Armstrong DATE RECEIVED:
DEPT: BUILDING DIVISION RECEIVED
FROM: Scott Weaver JUK 1 2?It
COMPANY: Riggs&Martin CITY OF TIGARD
BUILDING DIVISION
PHONE: 503-849-8482 By:
EMAIL: weaver@riggsandmartin.com
RE: 13191 SW Raptor Place MST2021-00142
(Site Address) (Permit Number)
Powell Garage Conversion
(Project name or subdivision name and lot number)
ATTACHED ARE THE FOLLOWING ITEMS:
Copies: Description: Copies: Description:
Additional set(s) of plans. 1 each Revisions: Plan Pages A2 and A7
Cross section(s)and details. Wall bracing and/or lateral analysis.
Floor/roof framing. Basement and retaining walls.
Beam calculations. Engineer's calculations.
Other(explain):
REMARKS: Adding notes and detail regarding slab edge insulation at exterior of rear exterior wall on plan pages A2 and A7.
Note to Allyson: Application of slab edge insulation is not feasible at new interior wall due to extent new footing extends into the
new living space.
FOR OFFICE USE ONLY
Routed to Permit Technic'an: Date:(c)f . z 1 Initials: NI-
Fees Due: ID No✓"fee Description: Amount Due:
$
v $
Special
Instructions:
Reprint Permit (per PE): ❑ Yes / g5No ❑ Done
Applicant Notified: ` � Date: /I M I J.LJ Initials: " l
RECEIVED
Oregon Residential Specialty Code R318.2 APR 1 3 202
CITY OF TIGARD
3UILDING DIVISION
MOISTURE CONTENT ACKNOWLEDGEMENT FORM
v v sz4..ve r— , am the general contractor or the owner-builder
at the following address:
Site Address: / 3 (ci / 540 ICsr ( _r uce_
City:
t .icy,(ZL
Permit#:
Subdivision/Lot#:
and/or
Map and Tax Lot#:
To conform with the 2017 Oregon Residential Specialty Code (ORSC), Section R318.2 and
OAR 918-480-0140, I am notifying the building official that I am aware of the moisture content
Requirement of ORSC Section R318.2 and have taken steps to meet this code requirement.
[Section R318.2 is provided for reference].
R318.2 Moisture Content: Prior to the installation of interior finishes, the building
official shall be notified in writing by the general contractor that all moisture-sensitive
wood framing members used in construction have a moisture content of not more than 19
percent by dry weight of dry framing members.
Signature: Date:
Gen I ontractor or Owner-Builder
I:\Building\Form\RES-Mo istureContentAcknowl edgement_022018