Report Oregon Residential Specialty Code R408.1
MOISTURE BARRIER ACKNOWLEDGEMENT FORM
I, , am the general contractor or the owner-builder
at the following address:
Site Address:
1L-ISct'-‘ St—)
City:
Permit#:
1.`--)\:5 -Oc) 6
Subdivision/Lot#: Ct3
and/or
Map and Tax Lot Oh
To conform with the 2014 Oregon Residential Specialty Code(ORSC), Section R408.1
Ventilation.I am notifying the building official that I have installed the Moisture Barrier as per
Requirement in ORSC Section 408.1 and have taken the following steps to meet this code
requirement:
r 'fhe ground surface of the under-floor space is covered with 6-mil blark polyethylene
sheeting with
LIintS lapped 12"at seams and
rq- xtending up the foundation walls 12".
sigoatur Date: -1( t 1419-1
or Owner-Builder
ts
1:93trildineFonnIRES-Moisturelkanc.r.doc 09/13/2016
Oregon Residential. Specialty Code N1107.2
HIGH-EFFICIENCY INTERIOR LIGHTING SYSTEMS
Permit No.: As-c- 4.0 RsD _00 1.4 G. Jurisdiction:
(
Site Address:
I Lii-Vst LA S Cm%CSC- C_O Or-ST
Subdivision/Lot#:
CA
and/or
Map and Tax Lot#:
By my signature below, I certify that a minimum of fifty(50)percent of the permanently
installed lighting fixtures in the above mentioned building have been installed with compact or
linear fluorescent, or a lighting source that has a minimum efficacy of 40 lumens per input watt.
(Oregon Residential Specialty Code N1107.2)I
Signature: Date: -7/I 4/2-1
'Cohtractor/Authonied Agent
Print Name: (- A',.2k.
ORSC Section N1107.2.High-efficiency interior lighting systems. A minimum of fifty(50)percent o the
permanently installed lighting fixtures shall be installed with compact or linear fluorescent,or a lighting source that
has a minimum efficacy of 40 lumens per input watt. Screw-in compact fluorescent lamps comply with this
requirement.
The building official shall be notified in writing at the final inspection that a minimum of fifty percent of the
permanently installed lighting fixtures are compact or linear fluorescent,or a minimum efficacy of 40 lumens per
input watt
IABuildingTorms1RES-HighEffieiencyLightinvioc 07/01/08
Moffet Energy Modeling
CCB#223372
Phone: 916-342-0742
tyler@moffetco.com
Blower Door Test Affidavit
Permit#: Builder: Taylor Morrison
Site Address: Roshak Lot 93: 14394 SW Gold Coast Ter,Tigard, OR 97224
Conditioned Floor Area (sq.ft.): 1168
Source: Calculated from plans Calculated Building Volume(cubic feet): 10678
TEST RESULTS: 793 CFM @ 50 Pa
ACH @ 50 Pa =((CFM x 60)_Volume): 4.46
Ring: Open OA B
Minneapolis Blower Door and DG 700 Manometer
I certify that these building leakage rates are accurate and determined using standard BPI testing
protocol.
Company Name: Moffet Energy Modeling Technician:Tyler Moffet
Technician Signature: ,_y/� !�� Date: 7/8/2021
(1,, 111400110e
44,;,w4l-t ,a.I NS Ut s*T1
Certificate of Compliance
This document certifies that the fiberglass insulation has been installed in conformance
with the manufacturer's recommendations and requirements to provide thermal resistance value(s)of:
R-value Thickness Coverage Area
Ceilings: R-49 X New Construction
Vaults/Slopes:
Walls: 0 Upgrade
Blown in R-23
Rim Joist:
Floors:
Over Garage R-38 _
Crawl Vapor Barrier installed Y N Sprinkler Tenting 4 mil Poly x Y _N
Loose-Fill Insulation
R-49 using_bags of insulation to cover 676 square feet of area at a thickness of 16.75 inches.
Owens Corning-PROPINK'L77 Loosefill Insulation
Owens Corning will accept no responsibility when the product is not installed in accordance with the product label.Stated R-value is provided by
installing the required number of bags at a thickness not less than the labeled minimum thickness.Installation of the required n umber ofbags may yield
more than the specified minimum thickness.Failure by the installer to provide both the required bags and at least the minimum thickness will result
in lower insulation R-value.
R-VALUE BAGS PER MAXIMUM NET MINIMUM WEIGHT MINUMUM
1000 SQ.FT. COVERAGE PER SQ.FT. THICKNESS
To obtain a No.of bags per 1000 sq. Contents of this bag Weight per sq. ft.of Installed insulation '
thermal resistance ft.of net area: should not cover installed insul.should should not be less
(R)of: more than:(sq. It.) not be less than:(lbs.) than:Iin.)
60 28.0 35.8 0.895 20.00
49 22.2 45.0 0.711 16.75
44 19.7 50.7 0.631 15.00
38 16.7 59.9 0.534 13.25 (
30 13.0 77.0 0.416 10.50 1
26 1 1.2 89.6 0.357 9.25
22 9.4 106.3 0.301 8.00
19 8.0 125.0 0.256 7.00
13 5.4 184.6 0.173 4.75
Property Address: 14394 SW Gold Coast Terrace Lot 93, Tigard,OR
5/11/21 Carolina Jarquin
Date of Installation Westside Drywall Inc.authorization
�7
7/02/21 r✓a2te1isia, I, -c aiv
Today's Date Build./Cs tractor's Signature 1
Taylor Morrison
Company/Customer Name
P.O.BOX 99*HUBBARD,OR 97032*(503)620-7036*FAX(503)624-0599*CCB#71044